[PATCH v3 3/3] drm/bridge: anx7625: add MIPI DPI input feature support

25 Jan 2021

Add MIPI rx DPI input support
Reported-by: kernel test robot lkp@intel.com
Signed-off-by: Xin Ji xji@analogixsemi.com
---
 drivers/gpu/drm/bridge/analogix/anx7625.c | 326 ++++++++++++++++++++++++------
 drivers/gpu/drm/bridge/analogix/anx7625.h |  20 +-
 2 files changed, 285 insertions(+), 61 deletions(-)

diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.c b/drivers/gpu/drm/bridge/analogix/anx7625.c
index 04536cc..c7fc92b 100644
--- a/drivers/gpu/drm/bridge/analogix/anx7625.c
+++ b/drivers/gpu/drm/bridge/analogix/anx7625.c
@@ -150,18 +150,18 @@ static int anx7625_write_and(struct anx7625_data *ctx,
    return anx7625_reg_write(ctx, client, offset, (val & (mask)));
 }
-static int anx7625_write_and_or(struct anx7625_data *ctx,
-				struct i2c_client *client,
-				u8 offset, u8 and_mask, u8 or_mask)
+static int anx7625_config_bit_matrix(struct anx7625_data *ctx)
 {
-	int val;
+	int i, ret;
-	val = anx7625_reg_read(ctx, client, offset);
-	if (val < 0)
-		return val;
+	ret = anx7625_write_or(ctx, ctx->i2c.tx_p2_client,
+			       AUDIO_CONTROL_REGISTER, 0x80);
+	for (i = 0; i < 13; i++)
+		ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
+					 VIDEO_BIT_MATRIX_12 + i,
+					 0x18 + i);
-	return anx7625_reg_write(ctx, client,
-				 offset, (val & and_mask) | (or_mask));
+	return ret;
 }
static int anx7625_read_ctrl_status_p0(struct anx7625_data *ctx)
@@ -195,6 +195,60 @@ static int wait_aux_op_finish(struct anx7625_data *ctx)
    return 0;
 }
+static int anx7625_aux_dpcd_read(struct anx7625_data *ctx,
+				 u8 addrh, u8 addrm, u8 addrl,
+				 u8 len, u8 *buf)
+{
+	struct device *dev = &ctx->client->dev;
+	int ret;
+	u8 cmd;
+
+	if (len > MAX_DPCD_BUFFER_SIZE) {
+		DRM_DEV_ERROR(dev, "exceed aux buffer len.\n");
+		return -EINVAL;
+	}
+
+	cmd = ((len - 1) << 4) | 0x09;
+
+	/* Set command and length */
+	ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				AP_AUX_COMMAND, cmd);
+
+	/* Set aux access address */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				 AP_AUX_ADDR_7_0, addrl);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				 AP_AUX_ADDR_15_8, addrm);
+	ret |= anx7625_write_and(ctx, ctx->i2c.rx_p0_client,
+				 AP_AUX_ADDR_19_16, addrh);
+
+	/* Enable aux access */
+	ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client,
+				AP_AUX_CTRL_STATUS, AP_AUX_CTRL_OP_EN);
+
+	if (ret < 0) {
+		DRM_DEV_ERROR(dev, "cannot access aux related register.\n");
+		return -EIO;
+	}
+
+	usleep_range(2000, 2100);
+
+	ret = wait_aux_op_finish(ctx);
+	if (ret) {
+		DRM_DEV_ERROR(dev, "aux IO error: wait aux op finish.\n");
+		return ret;
+	}
+
+	ret = anx7625_reg_block_read(ctx, ctx->i2c.rx_p0_client,
+				     AP_AUX_BUFF_START, len, buf);
+	if (ret < 0) {
+		DRM_DEV_ERROR(dev, "read dpcd register failed\n");
+		return -EIO;
+	}
+
+	return 0;
+}
+
 static int anx7625_video_mute_control(struct anx7625_data *ctx,
    			      u8 status)
 {
@@ -219,38 +273,6 @@ static int anx7625_video_mute_control(struct anx7625_data *ctx,
    return ret;
 }
-static int anx7625_config_audio_input(struct anx7625_data *ctx)
-{
-	struct device *dev = &ctx->client->dev;
-	int ret;
-
-	/* Channel num */
-	ret = anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
-				AUDIO_CHANNEL_STATUS_6, I2S_CH_2 << 5);
-
-	/* FS */
-	ret |= anx7625_write_and_or(ctx, ctx->i2c.tx_p2_client,
-				    AUDIO_CHANNEL_STATUS_4,
-				    0xf0, AUDIO_FS_48K);
-	/* Word length */
-	ret |= anx7625_write_and_or(ctx, ctx->i2c.tx_p2_client,
-				    AUDIO_CHANNEL_STATUS_5,
-				    0xf0, AUDIO_W_LEN_24_24MAX);
-	/* I2S */
-	ret |= anx7625_write_or(ctx, ctx->i2c.tx_p2_client,
-				AUDIO_CHANNEL_STATUS_6, I2S_SLAVE_MODE);
-	ret |= anx7625_write_and(ctx, ctx->i2c.tx_p2_client,
-				 AUDIO_CONTROL_REGISTER, ~TDM_TIMING_MODE);
-	/* Audio change flag */
-	ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client,
-				AP_AV_STATUS, AP_AUDIO_CHG);
-
-	if (ret < 0)
-		DRM_DEV_ERROR(dev, "fail to config audio.\n");
-
-	return ret;
-}
-
 /* Reduction of fraction a/b */
 static void anx7625_reduction_of_a_fraction(unsigned long *a, unsigned long *b)
 {
@@ -410,7 +432,7 @@ static int anx7625_dsi_video_timing_config(struct anx7625_data *ctx)
    ret |= anx7625_write_and(ctx, ctx->i2c.rx_p1_client,
    		MIPI_LANE_CTRL_0, 0xfc);
    ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client,
-				MIPI_LANE_CTRL_0, 3);
+				MIPI_LANE_CTRL_0, ctx->pdata.mipi_lanes - 1);
/* Htotal */
    htotal = ctx->dt.hactive.min + ctx->dt.hfront_porch.min +
@@ -595,6 +617,101 @@ static int anx7625_dsi_config(struct anx7625_data *ctx)
    return ret;
 }
+static int anx7625_api_dpi_config(struct anx7625_data *ctx)
+{
+	struct device *dev = &ctx->client->dev;
+	u16 freq = ctx->dt.pixelclock.min / 1000;
+	int ret;
+
+	/* configure pixel clock */
+	ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				PIXEL_CLOCK_L, freq & 0xFF);
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
+				 PIXEL_CLOCK_H, (freq >> 8));
+
+	/* set DPI mode */
+	/* set to DPI PLL module sel */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+				 MIPI_DIGITAL_PLL_9, 0x20);
+	/* power down MIPI */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+				 MIPI_LANE_CTRL_10, 0x08);
+	/* enable DPI mode */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client,
+				 MIPI_DIGITAL_PLL_18, 0x1C);
+	/* set first edge */
+	ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
+				 VIDEO_CONTROL_0, 0x06);
+	if (ret < 0)
+		DRM_DEV_ERROR(dev, "IO error : dpi phy set failed.\n");
+
+	return ret;
+}
+
+static int anx7625_dpi_config(struct anx7625_data *ctx)
+{
+	struct device *dev = &ctx->client->dev;
+	int ret;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "config dpi\n");
+
+	/* DSC disable */
+	ret = anx7625_write_and(ctx, ctx->i2c.rx_p0_client,
+				R_DSC_CTRL_0, ~DSC_EN);
+	if (ret < 0) {
+		DRM_DEV_ERROR(dev, "IO error : disable dsc failed.\n");
+		return ret;
+	}
+
+	ret = anx7625_config_bit_matrix(ctx);
+	if (ret < 0) {
+		DRM_DEV_ERROR(dev, "config bit matrix failed.\n");
+		return ret;
+	}
+
+	ret = anx7625_api_dpi_config(ctx);
+	if (ret < 0) {
+		DRM_DEV_ERROR(dev, "mipi phy(dpi) setup failed.\n");
+		return ret;
+	}
+
+	/* set MIPI RX EN */
+	ret = anx7625_write_or(ctx, ctx->i2c.rx_p0_client,
+			       AP_AV_STATUS, AP_MIPI_RX_EN);
+	/* clear mute flag */
+	ret |= anx7625_write_and(ctx, ctx->i2c.rx_p0_client,
+				 AP_AV_STATUS, (u8)~AP_MIPI_MUTE);
+	if (ret < 0)
+		DRM_DEV_ERROR(dev, "IO error : enable mipi rx failed.\n");
+
+	return ret;
+}
+
+static int anx7625_hdcp_setting(struct anx7625_data *ctx)
+{
+	u8 bcap;
+	struct device *dev = &ctx->client->dev;
+
+	if (!ctx->pdata.hdcp_support || !ctx->hdcp_en) {
+		DRM_DEV_DEBUG_DRIVER(dev, "hdcp_support(%d), hdcp_en(%d)\n",
+				     ctx->pdata.hdcp_support, ctx->hdcp_en);
+		DRM_DEV_DEBUG_DRIVER(dev, "disable HDCP by config\n");
+		return anx7625_write_and(ctx, ctx->i2c.rx_p1_client,
+					 0xee, 0x9f);
+	}
+
+	anx7625_aux_dpcd_read(ctx, 0x06, 0x80, 0x28, 1, &bcap);
+	if (!(bcap & 0x01)) {
+		DRM_WARN("downstream not support HDCP 1.4, cap(%x).\n", bcap);
+		return anx7625_write_and(ctx, ctx->i2c.rx_p1_client,
+					 0xee, 0x9f);
+	}
+
+	DRM_DEV_DEBUG_DRIVER(dev, "enable HDCP 1.4\n");
+
+	return anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xee, 0x20);
+}
+
 static void anx7625_dp_start(struct anx7625_data *ctx)
 {
    int ret;
@@ -605,9 +722,13 @@ static void anx7625_dp_start(struct anx7625_data *ctx)
    	return;
    }
-	anx7625_config_audio_input(ctx);
+	/* HDCP config */
+	anx7625_hdcp_setting(ctx);
-	ret = anx7625_dsi_config(ctx);
+	if (ctx->pdata.is_dpi)
+		ret = anx7625_dpi_config(ctx);
+	else
+		ret = anx7625_dsi_config(ctx);
if (ret < 0)
    	DRM_DEV_ERROR(dev, "MIPI phy setup error.\n");
@@ -688,8 +809,7 @@ static int sp_tx_get_edid_block(struct anx7625_data *ctx)
    return c;
 }
-static int edid_read(struct anx7625_data *ctx,
-		     u8 offset, u8 *pblock_buf)
+static int edid_read(struct anx7625_data *ctx, u8 offset, u8 *pblock_buf)
 {
    int ret, cnt;
    struct device *dev = &ctx->client->dev;
@@ -992,8 +1112,9 @@ static void anx7625_chip_control(struct anx7625_data *ctx, int state)
if (state) {
    	atomic_inc(&ctx->power_status);
-		if (atomic_read(&ctx->power_status) == 1)
+		if (atomic_read(&ctx->power_status) == 1) {
    		anx7625_power_on_init(ctx);
+		}
    } else {
    	if (atomic_read(&ctx->power_status)) {
    		atomic_dec(&ctx->power_status);
@@ -1051,6 +1172,7 @@ static void anx7625_start_dp_work(struct anx7625_data *ctx)
    	return;
    }
+	ctx->hpd_status = 1;
    ctx->hpd_high_cnt++;
/* Not support HDCP */
@@ -1060,8 +1182,10 @@ static void anx7625_start_dp_work(struct anx7625_data *ctx)
    ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xec, 0x10);
    /* Interrupt for DRM */
    ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xff, 0x01);
-	if (ret < 0)
+	if (ret < 0) {
+		DRM_DEV_ERROR(dev, "fail to setting HDCP/auth\n");
    	return;
+	}
ret = anx7625_reg_read(ctx, ctx->i2c.rx_p1_client, 0x86);
    if (ret < 0)
@@ -1080,6 +1204,10 @@ static void anx7625_hpd_polling(struct anx7625_data *ctx)
    int ret, val;
    struct device *dev = &ctx->client->dev;
+	/* Interrupt mode, no need poll HPD status, just return */
+	if (ctx->pdata.intp_irq)
+		return;
+
    if (atomic_read(&ctx->power_status) != 1) {
    	DRM_DEV_DEBUG_DRIVER(dev, "No need to poling HPD status.\n");
    	return;
@@ -1130,6 +1258,21 @@ static void anx7625_remove_edid(struct anx7625_data *ctx)
    ctx->slimport_edid_p.edid_block_num = -1;
 }
+static void anx7625_dp_adjust_swing(struct anx7625_data *ctx)
+{
+	int i;
+
+	for (i = 0; i < ctx->pdata.dp_lane0_swing_reg_cnt; i++)
+		anx7625_reg_write(ctx, ctx->i2c.tx_p1_client,
+				  DP_TX_LANE0_SWING_REG0 + i,
+				  ctx->pdata.lane0_reg_data[i] & 0xFF);
+
+	for (i = 0; i < ctx->pdata.dp_lane1_swing_reg_cnt; i++)
+		anx7625_reg_write(ctx, ctx->i2c.tx_p1_client,
+				  DP_TX_LANE1_SWING_REG0 + i,
+				  ctx->pdata.lane1_reg_data[i] & 0xFF);
+}
+
 static void dp_hpd_change_handler(struct anx7625_data *ctx, bool on)
 {
    struct device *dev = &ctx->client->dev;
@@ -1145,9 +1288,8 @@ static void dp_hpd_change_handler(struct anx7625_data *ctx, bool on)
    } else {
    	DRM_DEV_DEBUG_DRIVER(dev, " HPD high\n");
    	anx7625_start_dp_work(ctx);
+		anx7625_dp_adjust_swing(ctx);
    }
-
-	ctx->hpd_status = 1;
 }
static int anx7625_hpd_change_detect(struct anx7625_data *ctx)
@@ -1224,20 +1366,69 @@ static irqreturn_t anx7625_intr_hpd_isr(int irq, void *data)
    return IRQ_HANDLED;
 }
+static int anx7625_get_swing_setting(struct device *dev,
+				     struct anx7625_platform_data *pdata)
+{
+	int num_regs;
+
+	if (of_get_property(dev->of_node,
+			    "analogix,lane0-swing", &num_regs)) {
+		if (num_regs > DP_TX_SWING_REG_CNT)
+			num_regs = DP_TX_SWING_REG_CNT;
+
+		pdata->dp_lane0_swing_reg_cnt = num_regs;
+		of_property_read_u32_array(dev->of_node, "analogix,lane0-swing",
+					   pdata->lane0_reg_data, num_regs);
+	}
+
+	if (of_get_property(dev->of_node,
+			    "analogix,lane1-swing", &num_regs)) {
+		if (num_regs > DP_TX_SWING_REG_CNT)
+			num_regs = DP_TX_SWING_REG_CNT;
+
+		pdata->dp_lane1_swing_reg_cnt = num_regs;
+		of_property_read_u32_array(dev->of_node, "analogix,lane1-swing",
+					   pdata->lane1_reg_data, num_regs);
+	}
+
+	return 0;
+}
+
 static int anx7625_parse_dt(struct device *dev,
    		    struct anx7625_platform_data *pdata)
 {
    struct device_node *np = dev->of_node;
    struct drm_panel *panel;
    int ret;
+	int bus_type;
+	anx7625_get_swing_setting(dev, pdata);
+
+	pdata->is_dpi = 1; /* default dpi mode */
    pdata->mipi_host_node = of_graph_get_remote_node(np, 0, 0);
    if (!pdata->mipi_host_node) {
    	DRM_DEV_ERROR(dev, "fail to get internal panel.\n");
    	return -ENODEV;
    }
-	DRM_DEV_DEBUG_DRIVER(dev, "found dsi host node.\n");
+	of_property_read_u32(pdata->mipi_host_node, "bus-type", &bus_type);
+	if (bus_type == 5) /* bus type is Parallel(DSI) */
+		pdata->is_dpi = 0;
+
+	pdata->mipi_lanes = of_property_count_u32_elems(pdata->mipi_host_node,
+							"data-lanes");
+	if (pdata->mipi_lanes > MAX_LANES_SUPPORT || pdata->mipi_lanes < 0)
+		pdata->mipi_lanes = MAX_LANES_SUPPORT;
+
+	if (pdata->is_dpi)
+		DRM_DEV_DEBUG_DRIVER(dev, "found MIPI DPI host node.\n");
+	else
+		DRM_DEV_DEBUG_DRIVER(dev, "found MIPI DSI host node.\n");
+
+	ret = of_property_read_u32(np, "analogix,hdcp-support",
+				   &pdata->hdcp_support);
+	if (ret)
+		pdata->hdcp_support = 0;
ret = drm_of_find_panel_or_bridge(np, 1, 0, &panel, NULL);
    if (ret < 0) {
@@ -1300,9 +1491,13 @@ static enum drm_connector_status anx7625_sink_detect(struct anx7625_data *ctx)
 {
    struct device *dev = &ctx->client->dev;
-	DRM_DEV_DEBUG_DRIVER(dev, "sink detect, return connected\n");
+	DRM_DEV_DEBUG_DRIVER(dev, "sink detect\n");
+
+	if (ctx->pdata.panel_bridge)
+		return connector_status_connected;
-	return connector_status_connected;
+	return ctx->hpd_status ? connector_status_connected :
+				     connector_status_disconnected;
 }
static int anx7625_attach_dsi(struct anx7625_data *ctx)
@@ -1330,7 +1525,7 @@ static int anx7625_attach_dsi(struct anx7625_data *ctx)
    	return -EINVAL;
    }
-	dsi->lanes = 4;
+	dsi->lanes = ctx->pdata.mipi_lanes;
    dsi->format = MIPI_DSI_FMT_RGB888;
    dsi->mode_flags = MIPI_DSI_MODE_VIDEO	|
    	MIPI_DSI_MODE_VIDEO_SYNC_PULSE	|
@@ -1376,10 +1571,12 @@ static int anx7625_bridge_attach(struct drm_bridge *bridge,
    	return -ENODEV;
    }
-	err = anx7625_attach_dsi(ctx);
-	if (err) {
-		DRM_DEV_ERROR(dev, "Fail to attach to dsi : %d\n", err);
-		return err;
+	if (!ctx->pdata.is_dpi) {
+		err = anx7625_attach_dsi(ctx);
+		if (err) {
+			DRM_DEV_ERROR(dev, "Fail to attach to dsi : %d\n", err);
+			return err;
+		}
    }
if (ctx->pdata.panel_bridge) {
@@ -1478,6 +1675,10 @@ static bool anx7625_bridge_mode_fixup(struct drm_bridge *bridge,
DRM_DEV_DEBUG_DRIVER(dev, "drm mode fixup set\n");
+	/* No need fixup for external monitor */
+	if (!ctx->pdata.panel_bridge)
+		return true;
+
    hsync = mode->hsync_end - mode->hsync_start;
    hfp = mode->hsync_start - mode->hdisplay;
    hbp = mode->htotal - mode->hsync_end;
@@ -1786,8 +1987,13 @@ static int anx7625_i2c_probe(struct i2c_client *client,
platform->bridge.funcs = &anx7625_bridge_funcs;
    platform->bridge.of_node = client->dev.of_node;
-	platform->bridge.ops = DRM_BRIDGE_OP_EDID | DRM_BRIDGE_OP_HPD;
-	platform->bridge.type = DRM_MODE_CONNECTOR_eDP;
+	platform->bridge.ops = DRM_BRIDGE_OP_EDID;
+	if (!platform->pdata.panel_bridge)
+		platform->bridge.ops |= DRM_BRIDGE_OP_HPD |
+					DRM_BRIDGE_OP_DETECT;
+	platform->bridge.type = platform->pdata.panel_bridge ?
+				    DRM_MODE_CONNECTOR_eDP :
+				    DRM_MODE_CONNECTOR_DisplayPort;
    drm_bridge_add(&platform->bridge);
DRM_DEV_DEBUG_DRIVER(dev, "probe done\n");
diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.h b/drivers/gpu/drm/bridge/analogix/anx7625.h
index 193ad86..127081e 100644
--- a/drivers/gpu/drm/bridge/analogix/anx7625.h
+++ b/drivers/gpu/drm/bridge/analogix/anx7625.h
@@ -141,12 +141,20 @@
 #define  HORIZONTAL_BACK_PORCH_H      0x22  /* Bit[7:4] are reserved */
/******** END of I2C Address 0x72 *********/
+
+/***************************************************************/
+/* Register definition of device address 0x7a */
+#define DP_TX_SWING_REG_CNT		0x14
+#define DP_TX_LANE0_SWING_REG0		0x00
+#define DP_TX_LANE1_SWING_REG0		0x14
+/******** END of I2C Address 0x7a *********/
+
 /***************************************************************/
 /* Register definition of device address 0x7e */
#define  I2C_ADDR_7E_FLASH_CONTROLLER  0x7E
-#define FLASH_LOAD_STA 0x05
+#define FLASH_LOAD_STA          0x05
 #define FLASH_LOAD_STA_CHK	BIT(7)
#define  XTAL_FRQ_SEL    0x3F
@@ -347,11 +355,20 @@ struct s_edid_data {
/***************** Display End *****************/
+#define MAX_LANES_SUPPORT	4
+
 struct anx7625_platform_data {
    struct gpio_desc *gpio_p_on;
    struct gpio_desc *gpio_reset;
    struct drm_bridge *panel_bridge;
    int intp_irq;
+	int is_dpi;
+	int mipi_lanes;
+	int hdcp_support;
+	int dp_lane0_swing_reg_cnt;
+	int lane0_reg_data[DP_TX_SWING_REG_CNT];
+	int dp_lane1_swing_reg_cnt;
+	int lane1_reg_data[DP_TX_SWING_REG_CNT];
    u32 low_power_mode;
    struct device_node *mipi_host_node;
 };
@@ -371,6 +388,7 @@ struct anx7625_data {
    atomic_t power_status;
    int hpd_status;
    int hpd_high_cnt;
+	int hdcp_en;
    /* Lock for work queue */
    struct mutex lock;
    struct i2c_client *client;
-- 
2.7.4


    

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

[PATCH v3 3/3] drm/bridge: anx7625: add MIPI DPI input feature support