From: Thierry Reding treding@nvidia.com
This panel requires dual-channel mode. The device accepts command-mode data on 8 lanes and will therefore need a dual-channel DSI controller. The two interfaces that make up this device need to be instantiated in the controllers that gang up to provide the dual-channel DSI host.
Signed-off-by: Thierry Reding treding@nvidia.com --- .../bindings/panel/sharp,lq101r1sx01.txt | 46 +++ drivers/gpu/drm/panel/Kconfig | 13 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-sharp-lq101r1sx01.c | 426 +++++++++++++++++++++ 4 files changed, 486 insertions(+) create mode 100644 Documentation/devicetree/bindings/panel/sharp,lq101r1sx01.txt create mode 100644 drivers/gpu/drm/panel/panel-sharp-lq101r1sx01.c
diff --git a/Documentation/devicetree/bindings/panel/sharp,lq101r1sx01.txt b/Documentation/devicetree/bindings/panel/sharp,lq101r1sx01.txt new file mode 100644 index 000000000000..4ab4380ddac8 --- /dev/null +++ b/Documentation/devicetree/bindings/panel/sharp,lq101r1sx01.txt @@ -0,0 +1,46 @@ +Sharp Microelectronics 10.1" WQXGA TFT LCD panel + +This panel requires a dual-channel DSI host to operate. It supports two modes: +- left-right: each channel drives the left or right half of the screen +- even-odd: each channel drives the even or odd lines of the screen + +Each of the DSI channels controls a separate DSI peripheral. The peripheral +driven by the first link (DSI-LINK1), left or even, is considered the primary +peripheral and controls the device. The 'link2' property contains a phandle +to the peripheral driven by the second link (DSI-LINK2, right or odd). + +Note that in video mode the DSI-LINK1 interface always provides the left/even +pixels and DSI-LINK2 always provides the right/odd pixels. In command mode it +is possible to program either link to drive the left/even or right/odd pixels +but for the sake of consistency this binding assumes that the same assignment +is chosen as for video mode. + +Required properties: +- compatible: should be "sharp,lq101r1sx01" +- link2: phandle to the DSI peripheral on the secondary link. Note that the + presence of this property marks the containing node as DSI-LINK1. +- power-supply: phandle of the regulator that provides the supply voltage + +Optional properties: +- backlight: phandle of the backlight device attached to the panel + +Example: + + dsi@54300000 { + panel: panel@0 { + compatible = "sharp,lq101r1sx01"; + reg = <0>; + + link2 = <&secondary>; + + power-supply = <...>; + backlight = <...>; + }; + }; + + dsi@54400000 { + secondary: panel@0 { + compatible = "sharp,lq101r1sx01"; + reg = <0>; + }; + }; diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig index bee9f72b3a93..024e98ef8e4d 100644 --- a/drivers/gpu/drm/panel/Kconfig +++ b/drivers/gpu/drm/panel/Kconfig @@ -27,4 +27,17 @@ config DRM_PANEL_S6E8AA0 select DRM_MIPI_DSI select VIDEOMODE_HELPERS
+config DRM_PANEL_SHARP_LQ101R1SX01 + tristate "Sharp LQ101R1SX01 panel" + depends on OF + depends on DRM_MIPI_DSI + help + Say Y here if you want to enable support for Sharp LQ101R1SX01 + TFT-LCD modules. The panel has a 2560x1600 resolution and uses + 24 bit RGB per pixel. It provides a dual MIPI DSI interface to + the host and has a built-in LED backlight. + + To compile this driver as a module, choose M here: the module + will be called panel-sharp-lq101r1sx01. + endmenu diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile index 8b929212fad7..4b2a0430804b 100644 --- a/drivers/gpu/drm/panel/Makefile +++ b/drivers/gpu/drm/panel/Makefile @@ -1,3 +1,4 @@ obj-$(CONFIG_DRM_PANEL_SIMPLE) += panel-simple.o obj-$(CONFIG_DRM_PANEL_LD9040) += panel-ld9040.o obj-$(CONFIG_DRM_PANEL_S6E8AA0) += panel-s6e8aa0.o +obj-$(CONFIG_DRM_PANEL_SHARP_LQ101R1SX01) += panel-sharp-lq101r1sx01.o diff --git a/drivers/gpu/drm/panel/panel-sharp-lq101r1sx01.c b/drivers/gpu/drm/panel/panel-sharp-lq101r1sx01.c new file mode 100644 index 000000000000..09356697d22f --- /dev/null +++ b/drivers/gpu/drm/panel/panel-sharp-lq101r1sx01.c @@ -0,0 +1,426 @@ +/* + * Copyright (C) 2014 NVIDIA Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/backlight.h> +#include <linux/gpio/consumer.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/regulator/consumer.h> + +#include <drm/drmP.h> +#include <drm/drm_crtc.h> +#include <drm/drm_mipi_dsi.h> +#include <drm/drm_panel.h> + +#include <video/mipi_display.h> + +#include <linux/host1x.h> + +struct sharp_panel { + struct drm_panel base; + /* the datasheet refers to them as DSI-LINK1 and DSI-LINK2 */ + struct mipi_dsi_device *link1; + struct mipi_dsi_device *link2; + + struct backlight_device *backlight; + struct regulator *supply; + + bool prepared; + bool enabled; + + const struct drm_display_mode *mode; +}; + +static inline struct sharp_panel *to_sharp_panel(struct drm_panel *panel) +{ + return container_of(panel, struct sharp_panel, base); +} + +static int sharp_panel_write(struct sharp_panel *sharp, u16 offset, u8 value) +{ + u8 payload[3] = { offset >> 8, offset & 0xff, value }; + struct mipi_dsi_device *dsi = sharp->link1; + ssize_t err; + + err = mipi_dsi_generic_write(dsi, payload, sizeof(payload)); + if (err < 0) + dev_err(&dsi->dev, "failed to write %02x to %04x: %d\n", + value, offset, err); + + err = mipi_dsi_dcs_nop(dsi); + if (err < 0) + dev_err(&dsi->dev, "failed to send DCS nop: %d\n", err); + + usleep_range(10, 20); + + return err; +} + +static __maybe_unused int sharp_panel_read(struct sharp_panel *sharp, + u16 offset, u8 *value) +{ + ssize_t err; + + cpu_to_be16s(&offset); + + err = mipi_dsi_generic_read(sharp->link1, &offset, sizeof(offset), + value, sizeof(*value)); + if (err < 0) + dev_err(&sharp->link1->dev, "failed to read from %04x: %d\n", + offset, err); + + return err; +} + +static int sharp_panel_disable(struct drm_panel *panel) +{ + struct sharp_panel *sharp = to_sharp_panel(panel); + + if (!sharp->enabled) + return 0; + + if (sharp->backlight) { + sharp->backlight->props.power = FB_BLANK_POWERDOWN; + backlight_update_status(sharp->backlight); + } + + sharp->enabled = false; + + return 0; +} + +static int sharp_panel_unprepare(struct drm_panel *panel) +{ + struct sharp_panel *sharp = to_sharp_panel(panel); + int err; + + if (!sharp->prepared) + return 0; + + err = mipi_dsi_dcs_set_display_off(sharp->link1); + if (err < 0) + dev_err(panel->dev, "failed to set display off: %d\n", err); + + err = mipi_dsi_dcs_enter_sleep_mode(sharp->link1); + if (err < 0) + dev_err(panel->dev, "failed to enter sleep mode: %d\n", err); + + msleep(120); + + regulator_disable(sharp->supply); + + sharp->prepared = false; + + return 0; +} + +static int sharp_setup_symmetrical_split(struct mipi_dsi_device *left, + struct mipi_dsi_device *right, + const struct drm_display_mode *mode) +{ + int err; + + err = mipi_dsi_dcs_set_column_address(left, 0, mode->hdisplay / 2 - 1); + if (err < 0) + dev_err(&left->dev, "failed to set column address: %d\n", err); + + err = mipi_dsi_dcs_set_page_address(left, 0, mode->vdisplay - 1); + if (err < 0) + dev_err(&left->dev, "failed to set page address: %d\n", err); + + err = mipi_dsi_dcs_set_column_address(right, mode->hdisplay / 2, + mode->hdisplay - 1); + if (err < 0) + dev_err(&right->dev, "failed to set column address: %d\n", err); + + err = mipi_dsi_dcs_set_page_address(right, 0, mode->vdisplay - 1); + if (err < 0) + dev_err(&right->dev, "failed to set page address: %d\n", err); + + return 0; +} + +static int sharp_panel_prepare(struct drm_panel *panel) +{ + struct sharp_panel *sharp = to_sharp_panel(panel); + u8 format = MIPI_DCS_PIXEL_FMT_24BIT; + int err; + + if (sharp->prepared) + return 0; + + err = regulator_enable(sharp->supply); + if (err < 0) + return err; + + usleep_range(10000, 20000); + + err = mipi_dsi_dcs_soft_reset(sharp->link1); + if (err < 0) + dev_err(panel->dev, "soft reset failed: %d\n", err); + + msleep(120); + + err = mipi_dsi_dcs_exit_sleep_mode(sharp->link1); + if (err < 0) + dev_err(panel->dev, "failed to exit sleep mode: %d\n", err); + + /* + * The MIPI DCS specification mandates this delay only between the + * exit_sleep_mode and enter_sleep_mode commands, so it isn't strictly + * necessary here. + */ + /* + msleep(120); + */ + + /* set left-right mode */ + err = sharp_panel_write(sharp, 0x1000, 0x2a); + if (err < 0) + dev_err(panel->dev, "failed to set left-right mode: %d\n", err); + + /* enable command mode */ + err = sharp_panel_write(sharp, 0x1001, 0x01); + if (err < 0) + dev_err(panel->dev, "failed to enable command mode: %d\n", err); + + err = mipi_dsi_dcs_set_pixel_format(sharp->link1, format); + if (err < 0) + dev_err(panel->dev, "failed to set pixel format: %d\n", err); + + /* + * TODO: The device supports both left-right and even-odd split + * configurations, but this driver currently supports only the left- + * right split. To support a different mode a mechanism needs to be + * put in place to communicate the configuration back to the DSI host + * controller. + */ + err = sharp_setup_symmetrical_split(sharp->link1, sharp->link2, + sharp->mode); + if (err < 0) + dev_err(panel->dev, "failed to set up symmetrical split: %d\n", + err); + + err = mipi_dsi_dcs_set_display_on(sharp->link1); + if (err < 0) + dev_err(panel->dev, "failed to set display on: %d\n", err); + + sharp->prepared = true; + + return err; +} + +static int sharp_panel_enable(struct drm_panel *panel) +{ + struct sharp_panel *sharp = to_sharp_panel(panel); + + if (sharp->enabled) + return 0; + + if (sharp->backlight) { + sharp->backlight->props.power = FB_BLANK_UNBLANK; + backlight_update_status(sharp->backlight); + } + + sharp->enabled = true; + + return 0; +} + +static const struct drm_display_mode default_mode = { + .clock = 278000, + .hdisplay = 2560, + .hsync_start = 2560 + 128, + .hsync_end = 2560 + 128 + 64, + .htotal = 2560 + 128 + 64 + 64, + .vdisplay = 1600, + .vsync_start = 1600 + 4, + .vsync_end = 1600 + 4 + 8, + .vtotal = 1600 + 4 + 8 + 32, + .vrefresh = 60, +}; + +static int sharp_panel_get_modes(struct drm_panel *panel) +{ + struct drm_display_mode *mode; + + mode = drm_mode_duplicate(panel->drm, &default_mode); + if (!mode) { + dev_err(panel->drm->dev, "failed to add mode %ux%ux@%u\n", + default_mode.hdisplay, default_mode.vdisplay, + default_mode.vrefresh); + return -ENOMEM; + } + + drm_mode_set_name(mode); + + drm_mode_probed_add(panel->connector, mode); + + panel->connector->display_info.width_mm = 217; + panel->connector->display_info.height_mm = 136; + + return 1; +} + +static const struct drm_panel_funcs sharp_panel_funcs = { + .disable = sharp_panel_disable, + .unprepare = sharp_panel_unprepare, + .prepare = sharp_panel_prepare, + .enable = sharp_panel_enable, + .get_modes = sharp_panel_get_modes, +}; + +static const struct of_device_id sharp_of_match[] = { + { .compatible = "sharp,lq101r1sx01", }, + { } +}; +MODULE_DEVICE_TABLE(of, sharp_of_match); + +static int sharp_panel_add(struct sharp_panel *sharp) +{ + struct device_node *np; + int err; + + sharp->mode = &default_mode; + + sharp->supply = devm_regulator_get(&sharp->link1->dev, "power"); + if (IS_ERR(sharp->supply)) + return PTR_ERR(sharp->supply); + + np = of_parse_phandle(sharp->link1->dev.of_node, "backlight", 0); + if (np) { + sharp->backlight = of_find_backlight_by_node(np); + of_node_put(np); + + if (!sharp->backlight) + return -EPROBE_DEFER; + } + + drm_panel_init(&sharp->base); + sharp->base.funcs = &sharp_panel_funcs; + sharp->base.dev = &sharp->link1->dev; + + err = drm_panel_add(&sharp->base); + if (err < 0) + goto put_backlight; + + return 0; + +put_backlight: + if (sharp->backlight) + put_device(&sharp->backlight->dev); + + return err; +} + +static void sharp_panel_del(struct sharp_panel *sharp) +{ + if (sharp->base.dev) + drm_panel_remove(&sharp->base); + + if (sharp->backlight) + put_device(&sharp->backlight->dev); +} + +static int sharp_panel_probe(struct mipi_dsi_device *dsi) +{ + struct mipi_dsi_device *secondary = NULL; + struct sharp_panel *sharp; + struct device_node *np; + int err; + + dsi->lanes = 4; + dsi->format = MIPI_DSI_FMT_RGB888; + dsi->mode_flags = 0; + + /* Find DSI-LINK1 */ + np = of_parse_phandle(dsi->dev.of_node, "link2", 0); + if (np) { + secondary = of_find_mipi_dsi_device_by_node(np); + of_node_put(np); + + if (!secondary) + return -EPROBE_DEFER; + } + + sharp = devm_kzalloc(&dsi->dev, sizeof(*sharp), GFP_KERNEL); + if (!sharp) + return -ENOMEM; + + mipi_dsi_set_drvdata(dsi, sharp); + + /* register a panel for only the DSI-LINK1 interface */ + if (secondary) { + sharp->link2 = secondary; + sharp->link1 = dsi; + + err = sharp_panel_add(sharp); + if (err < 0) + return err; + } + + err = mipi_dsi_attach(dsi); + if (err < 0) { + sharp_panel_del(sharp); + return err; + } + + return 0; +} + +static int sharp_panel_remove(struct mipi_dsi_device *dsi) +{ + struct sharp_panel *sharp = mipi_dsi_get_drvdata(dsi); + int err; + + /* only detach from host for the DSI-LINK2 interface */ + if (!sharp->link2) { + mipi_dsi_detach(dsi); + return 0; + } + + err = sharp_panel_disable(&sharp->base); + if (err < 0) + dev_err(&dsi->dev, "failed to disable panel: %d\n", err); + + err = mipi_dsi_detach(dsi); + if (err < 0) + dev_err(&dsi->dev, "failed to detach from DSI host: %d\n", err); + + drm_panel_detach(&sharp->base); + drm_panel_remove(&sharp->base); + + if (sharp->backlight) + put_device(&sharp->backlight->dev); + + put_device(&sharp->link2->dev); + + return 0; +} + +static void sharp_panel_shutdown(struct mipi_dsi_device *dsi) +{ + struct sharp_panel *sharp = mipi_dsi_get_drvdata(dsi); + + sharp_panel_disable(&sharp->base); +} + +static struct mipi_dsi_driver sharp_panel_driver = { + .driver = { + .name = "panel-sharp-lq101r1sx01", + .of_match_table = sharp_of_match, + }, + .probe = sharp_panel_probe, + .remove = sharp_panel_remove, + .shutdown = sharp_panel_shutdown, +}; +module_mipi_dsi_driver(sharp_panel_driver); + +MODULE_AUTHOR("Thierry Reding treding@nvidia.com"); +MODULE_DESCRIPTION("Sharp LQ101R1SX01 panel driver"); +MODULE_LICENSE("GPL v2");