Pull mode registers programming from mxsfb_enable_controller() into dedicated function mxsfb_set_mode(). This is a clean up. No functional change.
Signed-off-by: Marek Vasut marex@denx.de Cc: Alexander Stein alexander.stein@ew.tq-group.com Cc: Laurent Pinchart laurent.pinchart@ideasonboard.com Cc: Lucas Stach l.stach@pengutronix.de Cc: Peng Fan peng.fan@nxp.com Cc: Robby Cai robby.cai@nxp.com Cc: Sam Ravnborg sam@ravnborg.org Cc: Stefan Agner stefan@agner.ch --- drivers/gpu/drm/mxsfb/mxsfb_kms.c | 96 +++++++++++++++++-------------- 1 file changed, 52 insertions(+), 44 deletions(-)
diff --git a/drivers/gpu/drm/mxsfb/mxsfb_kms.c b/drivers/gpu/drm/mxsfb/mxsfb_kms.c index 7b0abd0472aae..14f5cc590a51b 100644 --- a/drivers/gpu/drm/mxsfb/mxsfb_kms.c +++ b/drivers/gpu/drm/mxsfb/mxsfb_kms.c @@ -111,6 +111,57 @@ static void mxsfb_set_formats(struct mxsfb_drm_private *mxsfb, writel(ctrl, mxsfb->base + LCDC_CTRL); }
+static void mxsfb_set_mode(struct mxsfb_drm_private *mxsfb, u32 bus_flags) +{ + struct drm_display_mode *m = &mxsfb->crtc.state->adjusted_mode; + u32 vdctrl0, vsync_pulse_len, hsync_pulse_len; + + writel(TRANSFER_COUNT_SET_VCOUNT(m->crtc_vdisplay) | + TRANSFER_COUNT_SET_HCOUNT(m->crtc_hdisplay), + mxsfb->base + mxsfb->devdata->transfer_count); + + vsync_pulse_len = m->crtc_vsync_end - m->crtc_vsync_start; + + vdctrl0 = VDCTRL0_ENABLE_PRESENT | /* Always in DOTCLOCK mode */ + VDCTRL0_VSYNC_PERIOD_UNIT | + VDCTRL0_VSYNC_PULSE_WIDTH_UNIT | + VDCTRL0_SET_VSYNC_PULSE_WIDTH(vsync_pulse_len); + if (m->flags & DRM_MODE_FLAG_PHSYNC) + vdctrl0 |= VDCTRL0_HSYNC_ACT_HIGH; + if (m->flags & DRM_MODE_FLAG_PVSYNC) + vdctrl0 |= VDCTRL0_VSYNC_ACT_HIGH; + /* Make sure Data Enable is high active by default */ + if (!(bus_flags & DRM_BUS_FLAG_DE_LOW)) + vdctrl0 |= VDCTRL0_ENABLE_ACT_HIGH; + /* + * DRM_BUS_FLAG_PIXDATA_DRIVE_ defines are controller centric, + * controllers VDCTRL0_DOTCLK is display centric. + * Drive on positive edge -> display samples on falling edge + * DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE -> VDCTRL0_DOTCLK_ACT_FALLING + */ + if (bus_flags & DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE) + vdctrl0 |= VDCTRL0_DOTCLK_ACT_FALLING; + + writel(vdctrl0, mxsfb->base + LCDC_VDCTRL0); + + /* Frame length in lines. */ + writel(m->crtc_vtotal, mxsfb->base + LCDC_VDCTRL1); + + /* Line length in units of clocks or pixels. */ + hsync_pulse_len = m->crtc_hsync_end - m->crtc_hsync_start; + writel(set_hsync_pulse_width(mxsfb, hsync_pulse_len) | + VDCTRL2_SET_HSYNC_PERIOD(m->crtc_htotal), + mxsfb->base + LCDC_VDCTRL2); + + writel(SET_HOR_WAIT_CNT(m->crtc_htotal - m->crtc_hsync_start) | + SET_VERT_WAIT_CNT(m->crtc_vtotal - m->crtc_vsync_start), + mxsfb->base + LCDC_VDCTRL3); + + writel(SET_DOTCLK_H_VALID_DATA_CNT(m->hdisplay), + mxsfb->base + LCDC_VDCTRL4); + +} + static void mxsfb_enable_controller(struct mxsfb_drm_private *mxsfb) { u32 reg; @@ -236,7 +287,6 @@ static void mxsfb_crtc_mode_set_nofb(struct mxsfb_drm_private *mxsfb, struct drm_device *drm = mxsfb->crtc.dev; struct drm_display_mode *m = &mxsfb->crtc.state->adjusted_mode; u32 bus_flags = mxsfb->connector->display_info.bus_flags; - u32 vdctrl0, vsync_pulse_len, hsync_pulse_len; int err;
/* Mandatory eLCDIF reset as per the Reference Manual */ @@ -256,49 +306,7 @@ static void mxsfb_crtc_mode_set_nofb(struct mxsfb_drm_private *mxsfb, bus_flags); DRM_DEV_DEBUG_DRIVER(drm->dev, "Mode flags: 0x%08X\n", m->flags);
- writel(TRANSFER_COUNT_SET_VCOUNT(m->crtc_vdisplay) | - TRANSFER_COUNT_SET_HCOUNT(m->crtc_hdisplay), - mxsfb->base + mxsfb->devdata->transfer_count); - - vsync_pulse_len = m->crtc_vsync_end - m->crtc_vsync_start; - - vdctrl0 = VDCTRL0_ENABLE_PRESENT | /* Always in DOTCLOCK mode */ - VDCTRL0_VSYNC_PERIOD_UNIT | - VDCTRL0_VSYNC_PULSE_WIDTH_UNIT | - VDCTRL0_SET_VSYNC_PULSE_WIDTH(vsync_pulse_len); - if (m->flags & DRM_MODE_FLAG_PHSYNC) - vdctrl0 |= VDCTRL0_HSYNC_ACT_HIGH; - if (m->flags & DRM_MODE_FLAG_PVSYNC) - vdctrl0 |= VDCTRL0_VSYNC_ACT_HIGH; - /* Make sure Data Enable is high active by default */ - if (!(bus_flags & DRM_BUS_FLAG_DE_LOW)) - vdctrl0 |= VDCTRL0_ENABLE_ACT_HIGH; - /* - * DRM_BUS_FLAG_PIXDATA_DRIVE_ defines are controller centric, - * controllers VDCTRL0_DOTCLK is display centric. - * Drive on positive edge -> display samples on falling edge - * DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE -> VDCTRL0_DOTCLK_ACT_FALLING - */ - if (bus_flags & DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE) - vdctrl0 |= VDCTRL0_DOTCLK_ACT_FALLING; - - writel(vdctrl0, mxsfb->base + LCDC_VDCTRL0); - - /* Frame length in lines. */ - writel(m->crtc_vtotal, mxsfb->base + LCDC_VDCTRL1); - - /* Line length in units of clocks or pixels. */ - hsync_pulse_len = m->crtc_hsync_end - m->crtc_hsync_start; - writel(set_hsync_pulse_width(mxsfb, hsync_pulse_len) | - VDCTRL2_SET_HSYNC_PERIOD(m->crtc_htotal), - mxsfb->base + LCDC_VDCTRL2); - - writel(SET_HOR_WAIT_CNT(m->crtc_htotal - m->crtc_hsync_start) | - SET_VERT_WAIT_CNT(m->crtc_vtotal - m->crtc_vsync_start), - mxsfb->base + LCDC_VDCTRL3); - - writel(SET_DOTCLK_H_VALID_DATA_CNT(m->hdisplay), - mxsfb->base + LCDC_VDCTRL4); + mxsfb_set_mode(mxsfb, bus_flags); }
static int mxsfb_crtc_atomic_check(struct drm_crtc *crtc,