On Wed, 04 Dec 2019, Benjamin GAIGNARD benjamin.gaignard@st.com wrote:
On 12/4/19 10:35 AM, Thomas Zimmermann wrote:
Hi
Am 19.11.19 um 14:47 schrieb Benjamin Gaignard:
When compiling with W=1 few warnings about unused variables show up. This patch removes all the involved variables.
Signed-off-by: Benjamin Gaignard benjamin.gaignard@st.com
drivers/gpu/drm/drm_modes.c | 22 +++------------------- 1 file changed, 3 insertions(+), 19 deletions(-)
diff --git a/drivers/gpu/drm/drm_modes.c b/drivers/gpu/drm/drm_modes.c index 88232698d7a0..aca901aff042 100644 --- a/drivers/gpu/drm/drm_modes.c +++ b/drivers/gpu/drm/drm_modes.c @@ -233,7 +233,7 @@ struct drm_display_mode *drm_cvt_mode(struct drm_device *dev, int hdisplay, /* 3) Nominal HSync width (% of line period) - default 8 */ #define CVT_HSYNC_PERCENTAGE 8 unsigned int hblank_percentage;
int vsyncandback_porch, vback_porch, hblank;
int vsyncandback_porch, hblank;/* estimated the horizontal period */ tmp1 = HV_FACTOR * 1000000 -
@@ -249,7 +249,6 @@ struct drm_display_mode *drm_cvt_mode(struct drm_device *dev, int hdisplay, else vsyncandback_porch = tmp1; /* 10. Find number of lines in back porch */
vback_porch = vsyncandback_porch - vsync;@@ -386,9 +385,8 @@ drm_gtf_mode_complex(struct drm_device *dev, int hdisplay, int vdisplay, int top_margin, bottom_margin; int interlace; unsigned int hfreq_est;
- int vsync_plus_bp, vback_porch;
- unsigned int vtotal_lines, vfieldrate_est, hperiod;
- unsigned int vfield_rate, vframe_rate;
- int vsync_plus_bp;
- unsigned int vtotal_lines; int left_margin, right_margin; unsigned int total_active_pixels, ideal_duty_cycle; unsigned int hblank, total_pixels, pixel_freq;
@@ -451,23 +449,9 @@ drm_gtf_mode_complex(struct drm_device *dev, int hdisplay, int vdisplay, /* [V SYNC+BP] = RINT(([MIN VSYNC+BP] * hfreq_est / 1000000)) */ vsync_plus_bp = MIN_VSYNC_PLUS_BP * hfreq_est / 1000; vsync_plus_bp = (vsync_plus_bp + 500) / 1000;
- /* 9. Find the number of lines in V back porch alone: */
- vback_porch = vsync_plus_bp - V_SYNC_RQD; /* 10. Find the total number of lines in Vertical field period: */ vtotal_lines = vdisplay_rnd + top_margin + bottom_margin + vsync_plus_bp + GTF_MIN_V_PORCH;
- /* 11. Estimate the Vertical field frequency: */
- vfieldrate_est = hfreq_est / vtotal_lines;
- /* 12. Find the actual horizontal period: */
- hperiod = 1000000 / (vfieldrate_rqd * vtotal_lines);
- /* 13. Find the actual Vertical field frequency: */
- vfield_rate = hfreq_est / vtotal_lines;
- /* 14. Find the Vertical frame frequency: */
- if (interlaced)
vframe_rate = vfield_rate / 2;- else
vframe_rate = vfield_rate;The amount of unused code is quite large, which makes me wonder if there's something missing below where these variables are supposed to be used.
If these variables can be removed, comments should mention that steps 9 and 11 to 14 are being left out. After all, the function is fairly explicit about implementing the GTF algorithm step by step.
Best regards Thomas
If the goal is to keep all the steps then I could prefix all problematic variables with __maybe_unused macro.
The effect is the same; it hides a potential bug that should be analyzed and fixed. If you have the time, please look at the code and figure out what it's supposed to do, and why isn't it using the information. Look at git blame and log, was it always so, or did something change?
The warnings are about potential bugs. The objective or end goal is to fix the bugs, not to silence the warnings.
BR, Jani.
Benjamin
/* 15. Find number of pixels in left margin: */ if (margins) left_margin = (hdisplay_rnd * GTF_MARGIN_PERCENTAGE + 500) /
dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel