Restructure the qcom-wled bindings for the better readability.
Signed-off-by: Kiran Gunda kgunda@codeaurora.org Reviewed-by: Bjorn Andersson bjorn.andersson@linaro.org Reviewed-by: Rob Herring robh@kernel.org Acked-by: Daniel Thompson daniel.thompson@linaro.org Acked-by: Pavel Machek pavel@ucw.cz --- .../bindings/leds/backlight/qcom-wled.txt | 110 ++++++++++++++++----- 1 file changed, 85 insertions(+), 25 deletions(-)
diff --git a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt index fb39e32..14f28f2 100644 --- a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt +++ b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt @@ -1,30 +1,90 @@ Binding for Qualcomm Technologies, Inc. WLED driver
-Required properties: -- compatible: should be "qcom,pm8941-wled" -- reg: slave address - -Optional properties: -- default-brightness: brightness value on boot, value from: 0-4095 - default: 2048 -- label: The name of the backlight device -- qcom,cs-out: bool; enable current sink output -- qcom,cabc: bool; enable content adaptive backlight control -- qcom,ext-gen: bool; use externally generated modulator signal to dim -- qcom,current-limit: mA; per-string current limit; value from 0 to 25 - default: 20mA -- qcom,current-boost-limit: mA; boost current limit; one of: - 105, 385, 525, 805, 980, 1260, 1400, 1680 - default: 805mA -- qcom,switching-freq: kHz; switching frequency; one of: - 600, 640, 685, 738, 800, 872, 960, 1066, 1200, 1371, - 1600, 1920, 2400, 3200, 4800, 9600, - default: 1600kHz -- qcom,ovp: V; Over-voltage protection limit; one of: - 27, 29, 32, 35 - default: 29V -- qcom,num-strings: #; number of led strings attached; value from 1 to 3 - default: 2 +WLED (White Light Emitting Diode) driver is used for controlling display +backlight that is part of PMIC on Qualcomm Technologies, Inc. reference +platforms. The PMIC is connected to the host processor via SPMI bus. + +- compatible + Usage: required + Value type: <string> + Definition: should be one of: + "qcom,pm8941-wled" + "qcom,pmi8998-wled" + "qcom,pm660l-wled" + +- reg + Usage: required + Value type: <prop encoded array> + Definition: Base address of the WLED modules. + +- default-brightness + Usage: optional + Value type: <u32> + Definition: brightness value on boot, value from: 0-4095 + Default: 2048 + +- label + Usage: required + Value type: <string> + Definition: The name of the backlight device + +- qcom,cs-out + Usage: optional + Value type: <bool> + Definition: enable current sink output. + This property is supported only for PM8941. + +- qcom,cabc + Usage: optional + Value type: <bool> + Definition: enable content adaptive backlight control. + +- qcom,ext-gen + Usage: optional + Value type: <bool> + Definition: use externally generated modulator signal to dim. + This property is supported only for PM8941. + +- qcom,current-limit + Usage: optional + Value type: <u32> + Definition: mA; per-string current limit + value: For pm8941: from 0 to 25 with 5 mA step + Default 20 mA. + For pmi8998: from 0 to 30 with 5 mA step + Default 25 mA. + +- qcom,current-boost-limit + Usage: optional + Value type: <u32> + Definition: mA; boost current limit. + For pm8941: one of: 105, 385, 525, 805, 980, 1260, 1400, + 1680. Default: 805 mA + For pmi8998: one of: 105, 280, 450, 620, 970, 1150, 1300, + 1500. Default: 970 mA + +- qcom,switching-freq + Usage: optional + Value type: <u32> + Definition: kHz; switching frequency; one of: 600, 640, 685, 738, + 800, 872, 960, 1066, 1200, 1371, 1600, 1920, 2400, 3200, + 4800, 9600. + Default: for pm8941: 1600 kHz + for pmi8998: 800 kHz + +- qcom,ovp + Usage: optional + Value type: <u32> + Definition: V; Over-voltage protection limit; one of: + 27, 29, 32, 35. default: 29V + This property is supported only for PM8941. + +- qcom,num-strings + Usage: optional + Value type: <u32> + Definition: #; number of led strings attached; + value from 1 to 3. default: 2 + This property is supported only for PM8941.
Example: