Re: [PATCH v2] dt-bindings: display: renesas,du: Provide bindings for r8a779a0

Hello everybody,

On Tue, Sep 07, 2021 at 09:17:31PM +0200, Geert Uytterhoeven wrote:

On Tue, Sep 7, 2021 at 8:45 PM Rob Herring wrote:

...

On Mon, Sep 06, 2021 at 10:13:07AM +0200, Geert Uytterhoeven wrote:

...

On Thu, Sep 2, 2021 at 1:39 AM Kieran Bingham wrote:

...

From: Kieran Bingham kieran.bingham+renesas@ideasonboard.com

Extend the Renesas DU display bindings to support the r8a779a0 V3U.

Reviewed-by: Laurent Pinchart laurent.pinchart@ideasonboard.com Signed-off-by: Kieran Bingham kieran.bingham+renesas@ideasonboard.com

---

v2:

• Collected Laurent's tag
• Remove clock-names requirement
• Specify only a single clock

Thanks for the update!

...

--- a/Documentation/devicetree/bindings/display/renesas,du.yaml +++ b/Documentation/devicetree/bindings/display/renesas,du.yaml @@ -39,6 +39,7 @@ properties: - renesas,du-r8a77980 # for R-Car V3H compatible DU - renesas,du-r8a77990 # for R-Car E3 compatible DU - renesas,du-r8a77995 # for R-Car D3 compatible DU

•  - renesas,du-r8a779a0 # for R-Car V3U compatible DU
  
  

  reg: maxItems: 1

@@ -773,6 +774,55 @@ allOf: - reset-names - renesas,vsps

• • if:

•  properties:
  

•    compatible:
  

•      contains:
  

•        enum:
  

•          - renesas,du-r8a779a0
  

• then:

•  properties:
  

•    clocks:
  

•      items:
  

•        - description: Functional clock
  

•    clock-names:
  

•      maxItems: 1
  

•      items:
  

•        - const: du
  

•    interrupts:
  

•      maxItems: 2
  

•    resets:
  

•      maxItems: 1
  

•    reset-names:
  

•      items:
  

•        - const: du.0
  

This is now inconsistent with clock-names, which doesn't use a suffix.

But it is consistent with all the other cases of 'reset-names'. The problem is 'clock-names' is not consistent and should be 'du.0'.

True.

Looks fine to me. The only other SoC that has a similar shared clock architecture is H1 (R8A7779), and we use du.0 there.

...

Ideally, the if/them schemas should not be defining the names. That should be at the top level and the if/them schema just limits the number of entries. That's not always possible, but I think is for clocks and resets in this case.

It's a bit tricky. For clocks, there's usually one clock per channel, but not always. Plus clocks for external inputs, if present.

Yes, it's mostly the external clocks that mess things up here. Each DU channel typically has one internal clock and one optional external clock, but not always.

For resets, there's one reset for a group of channels, with the number of channels in a group depending on the SoC family. And then there's the special casing for SoCs where there's a gap in the channel numbering...

For resets, H1 and M3-N are indeed special cases. H1 has no reset-names, while M3-N has du.0 and du.3 due to a gap in hardware channel numbering. All other SoCs have du.0 and optionally du.2.

Still wondering if it would be better to have one device node per channel, and companion links...

The hardware design would make that too messy. There are too many cross-channel dependencies.