From: Wolfram Sang wsa+renesas@sang-engineering.com
Fix this typo, consequently used over both files :)
Signed-off-by: Wolfram Sang wsa+renesas@sang-engineering.com Acked-by: Lars-Peter Clausen lars@metafoo.de Reviewed-by: Laurent Pinchart laurent.pinchart@ideasonboard.com Tested-by: Archit Taneja architt@codeaurora.org --- drivers/gpu/drm/i2c/adv7511.c | 22 +++++++++++----------- drivers/gpu/drm/i2c/adv7511.h | 12 ++++++------ 2 files changed, 17 insertions(+), 17 deletions(-)
diff --git a/drivers/gpu/drm/i2c/adv7511.c b/drivers/gpu/drm/i2c/adv7511.c index e1756a452d6980..a02112ba1c3df6 100644 --- a/drivers/gpu/drm/i2c/adv7511.c +++ b/drivers/gpu/drm/i2c/adv7511.c @@ -378,16 +378,16 @@ static void adv7511_power_on(struct adv7511 *adv7511) }
/* - * Per spec it is allowed to pulse the HDP signal to indicate that the + * Per spec it is allowed to pulse the HPD signal to indicate that the * EDID information has changed. Some monitors do this when they wakeup - * from standby or are enabled. When the HDP goes low the adv7511 is + * from standby or are enabled. When the HPD goes low the adv7511 is * reset and the outputs are disabled which might cause the monitor to - * go to standby again. To avoid this we ignore the HDP pin for the + * go to standby again. To avoid this we ignore the HPD pin for the * first few seconds after enabling the output. */ regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2, - ADV7511_REG_POWER2_HDP_SRC_MASK, - ADV7511_REG_POWER2_HDP_SRC_NONE); + ADV7511_REG_POWER2_HPD_SRC_MASK, + ADV7511_REG_POWER2_HPD_SRC_NONE);
/* * Most of the registers are reset during power down or when HPD is low. @@ -421,9 +421,9 @@ static bool adv7511_hpd(struct adv7511 *adv7511) if (ret < 0) return false;
- if (irq0 & ADV7511_INT0_HDP) { + if (irq0 & ADV7511_INT0_HPD) { regmap_write(adv7511->regmap, ADV7511_REG_INT(0), - ADV7511_INT0_HDP); + ADV7511_INT0_HPD); return true; }
@@ -446,7 +446,7 @@ static int adv7511_irq_process(struct adv7511 *adv7511) regmap_write(adv7511->regmap, ADV7511_REG_INT(0), irq0); regmap_write(adv7511->regmap, ADV7511_REG_INT(1), irq1);
- if (irq0 & ADV7511_INT0_HDP && adv7511->encoder) + if (irq0 & ADV7511_INT0_HPD && adv7511->encoder) drm_helper_hpd_irq_event(adv7511->encoder->dev);
if (irq0 & ADV7511_INT0_EDID_READY || irq1 & ADV7511_INT1_DDC_ERROR) { @@ -648,10 +648,10 @@ adv7511_encoder_detect(struct drm_encoder *encoder, if (adv7511->status == connector_status_connected) status = connector_status_disconnected; } else { - /* Renable HDP sensing */ + /* Renable HPD sensing */ regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2, - ADV7511_REG_POWER2_HDP_SRC_MASK, - ADV7511_REG_POWER2_HDP_SRC_BOTH); + ADV7511_REG_POWER2_HPD_SRC_MASK, + ADV7511_REG_POWER2_HPD_SRC_BOTH); }
adv7511->status = status; diff --git a/drivers/gpu/drm/i2c/adv7511.h b/drivers/gpu/drm/i2c/adv7511.h index 6599ed538426d6..38515b30cedfc8 100644 --- a/drivers/gpu/drm/i2c/adv7511.h +++ b/drivers/gpu/drm/i2c/adv7511.h @@ -90,7 +90,7 @@ #define ADV7511_CSC_ENABLE BIT(7) #define ADV7511_CSC_UPDATE_MODE BIT(5)
-#define ADV7511_INT0_HDP BIT(7) +#define ADV7511_INT0_HPD BIT(7) #define ADV7511_INT0_VSYNC BIT(5) #define ADV7511_INT0_AUDIO_FIFO_FULL BIT(4) #define ADV7511_INT0_EDID_READY BIT(2) @@ -157,11 +157,11 @@ #define ADV7511_PACKET_ENABLE_SPARE2 BIT(1) #define ADV7511_PACKET_ENABLE_SPARE1 BIT(0)
-#define ADV7511_REG_POWER2_HDP_SRC_MASK 0xc0 -#define ADV7511_REG_POWER2_HDP_SRC_BOTH 0x00 -#define ADV7511_REG_POWER2_HDP_SRC_HDP 0x40 -#define ADV7511_REG_POWER2_HDP_SRC_CEC 0x80 -#define ADV7511_REG_POWER2_HDP_SRC_NONE 0xc0 +#define ADV7511_REG_POWER2_HPD_SRC_MASK 0xc0 +#define ADV7511_REG_POWER2_HPD_SRC_BOTH 0x00 +#define ADV7511_REG_POWER2_HPD_SRC_HPD 0x40 +#define ADV7511_REG_POWER2_HPD_SRC_CEC 0x80 +#define ADV7511_REG_POWER2_HPD_SRC_NONE 0xc0 #define ADV7511_REG_POWER2_TDMS_ENABLE BIT(4) #define ADV7511_REG_POWER2_GATE_INPUT_CLK BIT(0)