On 2020-11-02 12:59, Stephen Boyd wrote:
Quoting Kuogee Hsieh (2020-10-30 16:22:53)
DP compo phy have to be enable to start link training. When link training failed phy need to be disabled so that next link trainng can be proceed smoothly at next plug in. This
s/trainng/training/
patch de initialize mainlink to disable phy if link training
s/de/de-/
failed. This prevent system crash due to disp_cc_mdss_dp_link_intf_clk stuck at "off" state. This patch also perform checking power_on flag at dp_display_enable() and dp_display_disable() to avoid crashing when unplug cable while display is off.
Fixes: fdaf9a5e3c15 (drm/msm/dp: fixes wrong connection state caused by failure of link train
Drop newline please.
Signed-off-by: Kuogee Hsieh khsieh@codeaurora.org
Can you send this as a patch series? There were three patches sent near each other and presumably they're related.
drivers/gpu/drm/msm/dp/dp_ctrl.c | 34 +++++++++++++++++++++++++++-- drivers/gpu/drm/msm/dp/dp_display.c | 13 +++++++++++ 2 files changed, 45 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/msm/dp/dp_ctrl.c b/drivers/gpu/drm/msm/dp/dp_ctrl.c index cee161c8ecc6..904698dfc7f7 100644 --- a/drivers/gpu/drm/msm/dp/dp_ctrl.c +++ b/drivers/gpu/drm/msm/dp/dp_ctrl.c @@ -1468,6 +1468,29 @@ static int dp_ctrl_reinitialize_mainlink(struct dp_ctrl_private *ctrl) return ret; }
+static int dp_ctrl_deinitialize_mainlink(struct dp_ctrl_private *ctrl) +{
struct dp_io *dp_io;struct phy *phy;int ret = 0;Please drop this initialization to 0.
dp_io = &ctrl->parser->io;phy = dp_io->phy;dp_catalog_ctrl_mainlink_ctrl(ctrl->catalog, false);dp_catalog_ctrl_reset(ctrl->catalog);ret = dp_power_clk_enable(ctrl->power, DP_CTRL_PM, false);As it's overwritten here.
if (ret)DRM_ERROR("Failed to disable link clocks. ret=%d\n",ret);
phy_power_off(phy);phy_exit(phy);return -ECONNRESET;Isn't this an error for networking connections getting reset? Really it should return 0 because it didn't fail.
+}
static int dp_ctrl_link_maintenance(struct dp_ctrl_private *ctrl) { int ret = 0; @@ -1648,8 +1671,7 @@ int dp_ctrl_on_link(struct dp_ctrl *dp_ctrl) if (rc) return rc;
while (--link_train_max_retries &&!atomic_read(&ctrl->dp_ctrl.aborted)) {
while (--link_train_max_retries) { rc = dp_ctrl_reinitialize_mainlink(ctrl); if (rc) { DRM_ERROR("Failed to reinitialize mainlink.rc=%d\n", @@ -1664,6 +1686,9 @@ int dp_ctrl_on_link(struct dp_ctrl *dp_ctrl) break; } else if (training_step == DP_TRAINING_1) { /* link train_1 failed */
if(!dp_catalog_hpd_get_state_status(ctrl->catalog))
break; /* link cableunplugged */
rc = dp_ctrl_link_rate_down_shift(ctrl); if (rc < 0) { /* already in RBR = 1.6G */ if (cr.lane_0_1 & DP_LANE0_1_CR_DONE){ @@ -1683,6 +1708,9 @@ int dp_ctrl_on_link(struct dp_ctrl *dp_ctrl) } } else if (training_step == DP_TRAINING_2) { /* link train_2 failed, lower lane rate */
if(!dp_catalog_hpd_get_state_status(ctrl->catalog))
Maybe make a function called dp_catalog_link_disconnected()? Then the comment isn't needed.
break; /* link cableunplugged */
rc = dp_ctrl_link_lane_down_shift(ctrl); if (rc < 0) { /* end with failure */@@ -1703,6 +1731,8 @@ int dp_ctrl_on_link(struct dp_ctrl *dp_ctrl) */ if (rc == 0) /* link train successfully */ dp_ctrl_push_idle(dp_ctrl);
elserc = dp_ctrl_deinitialize_mainlink(ctrl);So if it fails we deinitialize and then return success? Shouldn't we keep the error code from the link train attempt instead of overwrite it with (most likely) zero? I see that it returns -ECONNRESET but that's really odd and seeing this code here means you have to look at the function to figure out that it's still returning an error code. Please don't do that, just ignore the error code from this function.
There are two possible failure cases at plugin request, link training failed and read dpcd/edid failed. It does not need to enable phy/pll to perform aux read/write from/to dpcd or edid. on the other hand, phy/pll need to be enabled to perform link training. If link training failed, then phy/pll need to be disabled so that phy/pll can be enabled next link training correctly. Link training failed error has to be propagated back to the top caller so that dp_display_host_init() will be called again at next plugin request.
return rc;} diff --git a/drivers/gpu/drm/msm/dp/dp_display.c b/drivers/gpu/drm/msm/dp/dp_display.c index 3eb0d428abf7..13b66266cd69 100644 --- a/drivers/gpu/drm/msm/dp/dp_display.c +++ b/drivers/gpu/drm/msm/dp/dp_display.c @@ -529,6 +529,11 @@ static int dp_hpd_plug_handle(struct dp_display_private *dp, u32 data) if (ret) { /* link train failed */ hpd->hpd_high = 0; dp->hpd_state = ST_DISCONNECTED;
if (ret == -ECONNRESET) { /* cable unplugged */dp->core_initialized = false;}Style: Drop braces on single line if statements.
} else { /* start sentinel checking in case of missing uevent*/ dp_add_event(dp, EV_CONNECT_PENDING_TIMEOUT, 0, tout); @@ -794,6 +799,11 @@ static int dp_display_enable(struct dp_display_private *dp, u32 data)
dp_display = g_dp_display;
if (dp_display->power_on) {DRM_DEBUG_DP("Link already setup, return\n");return 0;}rc = dp_ctrl_on_stream(dp->ctrl); if (!rc) dp_display->power_on = true;@@ -826,6 +836,9 @@ static int dp_display_disable(struct dp_display_private *dp, u32 data)
dp_display = g_dp_display;
if (!dp_display->power_on)return -EINVAL;/* wait only if audio was enabled */ if (dp_display->audio_enabled) { if (!wait_for_completion_timeout(&dp->audio_comp,base-commit: fd4a29bed29b3d8f15942fdf77e7a0a52796d836
What is this commit?