This binding describes the Amlogic Meson specific extension to the Synopsys Designware HDMI Controller.
Signed-off-by: Neil Armstrong narmstrong@baylibre.com --- .../bindings/display/amlogic,meson-dw-hdmi.txt | 111 +++++++++++++++++++++ 1 file changed, 111 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/amlogic,meson-dw-hdmi.txt
diff --git a/Documentation/devicetree/bindings/display/amlogic,meson-dw-hdmi.txt b/Documentation/devicetree/bindings/display/amlogic,meson-dw-hdmi.txt new file mode 100644 index 0000000..7f040ed --- /dev/null +++ b/Documentation/devicetree/bindings/display/amlogic,meson-dw-hdmi.txt @@ -0,0 +1,111 @@ +Amlogic specific extensions to the Synopsys Designware HDMI Controller +====================================================================== + +The Amlogic Meson Synopsys Designware Integration is composed of : +- A Synopsys DesignWare HDMI Controller IP +- A TOP control block controlling the Clocks and PHY +- A custom HDMI PHY in order to convert video to TMDS signal + ___________________________________ +| HDMI TOP |<= HPD +|___________________________________| +| | | +| Synopsys HDMI | HDMI PHY |=> TMDS +| Controller |________________| +|___________________________________|<=> DDC + +The HDMI TOP block only supports HPD sensing. +The Synopsys HDMI Controller interrupt is routed through the +TOP Block interrupt. +Communication to the TOP Block and the Synopsys HDMI Controller is done +via a pair of dedicated addr+read/write registers. +The HDMI PHY is configured by registers in the HHI register block. + +Pixel data arrives in 4:4:4 format from the VENC block and the VPU HDMI mux +selects either the ENCI encoder for the 576i or 480i formats or the ENCP +encoder for all the other formats including interlaced HD formats. + +The VENC uses a DVI encoder on top of the ENCI or ENCP encoders to generate +DVI timings for the HDMI controller. + +Amlogic Meson GXBB, GXL and GXM SoCs families embeds the Synopsys DesignWare +HDMI TX IP version 2.01a with HDCP and I2C & S/PDIF +audio source interfaces. + +Required properties: +- compatible: value should be different for each SoC family as : + - GXBB (S905) : "amlogic,meson-gxbb-dw-hdmi" + - GXL (S905X, S905D) : "amlogic,meson-gxl-dw-hdmi" + - GXM (S912) : "amlogic,meson-gxm-dw-hdmi" + followed by the common "amlogic,meson-gx-dw-hdmi" +- reg: Physical base address and length of the controller's registers. +- interrupts: The HDMI interrupt number +- clocks, clock-names : must have the phandles to the HDMI iahb and isfr clocks, + and the Amlogic Meson venci clocks as described in + Documentation/devicetree/bindings/clock/clock-bindings.txt, + the clocks are soc specific, the clock-names should be "iahb", "isfr", "venci" +- resets, resets-names: must have the phandles to the HDMI apb, glue and phy + resets as described in : + Documentation/devicetree/bindings/reset/reset.txt, + the reset-names should be "hdmitx_apb", "hdmitx", "hdmitx_phy" + +Required nodes: + +The connections to the HDMI ports are modeled using the OF graph +bindings specified in Documentation/devicetree/bindings/graph.txt. + +The following table lists for each supported model the port number +corresponding to each HDMI output and input. + + Port 0 Port 1 +----------------------------------------- + S905 (GXBB) VENC Input TMDS Output + S905X (GXL) VENC Input TMDS Output + S905D (GXL) VENC Input TMDS Output + S912 (GXM) VENC Input TMDS Output + +Example: + +hdmi-connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&hdmi_tx_tmds_out>; + }; + }; +}; + +hdmi_tx: hdmi-tx@c883a000 { + compatible = "amlogic,meson-gxbb-dw-hdmi", "amlogic,meson-gx-dw-hdmi"; + reg = <0x0 0xc883a000 0x0 0x1c>; + interrupts = <GIC_SPI 57 IRQ_TYPE_EDGE_RISING>; + resets = <&reset RESET_HDMITX_CAPB3>, + <&reset RESET_HDMI_SYSTEM_RESET>, + <&reset RESET_HDMI_TX>; + reset-names = "hdmitx_apb", "hdmitx", "hdmitx_phy"; + clocks = <&clkc CLKID_HDMI_PCLK>, + <&clkc CLKID_CLK81>, + <&clkc CLKID_GCLK_VENCI_INT0>; + clock-names = "isfr", "iahb", "venci"; + #address-cells = <1>; + #size-cells = <0>; + + /* VPU VENC Input */ + hdmi_tx_venc_port: port@0 { + reg = <0>; + + hdmi_tx_in: endpoint { + remote-endpoint = <&hdmi_tx_out>; + }; + }; + + /* TMDS Output */ + hdmi_tx_tmds_port: port@1 { + reg = <1>; + + hdmi_tx_tmds_out: endpoint { + remote-endpoint = <&hdmi_connector_in>; + }; + }; +};