The BPI-M1+ has an FPC connector for connecting an RGB (parallel) or LVDS LCD panel. One of the compatible panels is a 7" 800x480 RGB panel from Bananapi. The backlight can be controlled by driving a PWM signal from the SoC at different duty cycles. The LCD enable pin does not seem to do anything, but it is nevertheless included for completeness. There is also a FT5306 capacitive touchscreen controller.
This should not be confused with the other 7" LCD that is LVDS based and has a resolution of 1024x600.
This patch enables all of the above for the BPI-M1+.
Signed-off-by: Chen-Yu Tsai wens@csie.org --- .../boot/dts/sun7i-a20-bananapi-m1-plus.dts | 61 +++++++++++++++++++ 1 file changed, 61 insertions(+)
diff --git a/arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts b/arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts index 763cb03033c4..58a923bfa6ef 100644 --- a/arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts +++ b/arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts @@ -47,6 +47,7 @@ #include "sunxi-common-regulators.dtsi" #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/pwm/pwm.h>
/ { model = "Banana Pi BPI-M1-Plus"; @@ -71,6 +72,34 @@ }; };
+ lcd_backlight: lcd-backlight { + compatible = "pwm-backlight"; + pwms = <&pwm 0 20000 PWM_POLARITY_INVERTED>; /* 50 kHz */ + enable-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */ + brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>; + default-brightness-level = <8>; + }; + + lcd_panel: lcd-panel { + compatible = "bananapi,s070wv20-ct16", "simple-panel"; + /* This doesn't do anything for this particular panel */ + enable-gpios = <&pio 7 12 GPIO_ACTIVE_HIGH>; /* PH12 */ + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + backlight = <&lcd_backlight>; + #address-cells = <1>; + #size-cells = <0>; + + lcd_panel_input: endpoint@0 { + reg = <0>; + remote-endpoint = <&tcon0_out_lcd>; + }; + }; + }; + leds { compatible = "gpio-leds"; pinctrl-names = "default"; @@ -173,6 +202,20 @@ status = "okay"; };
+&i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c3_pins_a>; + status = "okay"; + + touchscreen@38 { + compatible = "edt,edt-ft5306", "edt,edt-ft5x06"; + reg = <0x38>; + interrupt-parent = <&pio>; + interrupts = <7 7 IRQ_TYPE_EDGE_FALLING>; /* PH7 */ + reset-gpios = <&pio 7 8 GPIO_ACTIVE_LOW>; /* PH8 */ + }; +}; + &ir0 { pinctrl-names = "default"; pinctrl-0 = <&ir0_rx_pins_a>; @@ -249,6 +292,12 @@ }; };
+&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm0_pins_a>; + status = "okay"; +}; + ®_dcdc2 { regulator-always-on; regulator-min-microvolt = <1000000>; @@ -278,6 +327,18 @@ status = "okay"; };
+&tcon0 { + pinctrl-names = "default"; + pinctrl-0 = <&lcd0_rgb888_pins>; +}; + +&tcon0_out { + tcon0_out_lcd: endpoint@0 { + reg = <0>; + remote-endpoint = <&lcd_panel_input>; + }; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pins_a>;