This defines all the DSC parameters as per the VESA DSC spec that will be required for DSC encoder/decoder
v6: (From Manasi) * Add a bit mask for RANGE_BPG_OFFSET for 6 bits(Manasi) v5 (From Manasi) * Add the RC constants as per the spec v4 (From Manasi) * Add the DSC_MUX_WORD_SIZE constants (Manasi)
v3 (From Manasi) * Remove the duplicate define (Suggested By:Harry Wentland)
v2: Define this struct in DRM (From Manasi) * Changed the data types to u8/u16 instead of unsigned longs (Manasi) * Remove driver specific fields (Manasi) * Move this struct definition to DRM (Manasi) * Define DSC 1.2 parameters (Manasi) * Use DSC_NUM_BUF_RANGES (Manasi) * Call it drm_dsc_config (Manasi)
Cc: dri-devel@lists.freedesktop.org Cc: Jani Nikula jani.nikula@linux.intel.com Cc: Ville Syrjala ville.syrjala@linux.intel.com Cc: Anusha Srivatsa anusha.srivatsa@intel.com Cc: Harry Wentland harry.wentland@amd.com Signed-off-by: Manasi Navare manasi.d.navare@intel.com Signed-off-by: Gaurav K Singh gaurav.k.singh@intel.com Co-developed-by: Gaurav K Singh gaurav.k.singh@intel.com Acked-by: Harry Wentland harry.wentland@amd.com Reviewed-by: Anusha Srivatsa anusha.srivatsa@intel.com --- include/drm/drm_dsc.h | 115 +++++++++++++++++++++++++++++++++++++++++- 1 file changed, 114 insertions(+), 1 deletion(-)
diff --git a/include/drm/drm_dsc.h b/include/drm/drm_dsc.h index 78db4f61d01c..3292dfed9d0a 100644 --- a/include/drm/drm_dsc.h +++ b/include/drm/drm_dsc.h @@ -11,7 +11,120 @@ #include <drm/drm_dp_helper.h>
/* VESA Display Stream Compression DSC 1.2 constants */ -#define DSC_NUM_BUF_RANGES 15 +#define DSC_NUM_BUF_RANGES 15 +#define DSC_MUX_WORD_SIZE_8_10_BPC 48 +#define DSC_MUX_WORD_SIZE_12_BPC 64 +#define DSC_RC_PIXELS_PER_GROUP 3 +#define DSC_SCALE_DECREMENT_INTERVAL_MAX 4095 +#define DSC_RANGE_BPG_OFFSET_MASK 0x3f + +/* Configuration for a single Rate Control model range */ +struct drm_dsc_rc_range_parameters { + /* Min Quantization Parameters allowed for this range */ + u8 range_min_qp; + /* Max Quantization Parameters allowed for this range */ + u8 range_max_qp; + /* Bits/group offset to apply to target for this group */ + u8 range_bpg_offset; +}; + +struct drm_dsc_config { + /* Bits / component for previous reconstructed line buffer */ + u8 line_buf_depth; + /* Bits per component to code (must be 8, 10, or 12) */ + u8 bits_per_component; + /* + * Flag indicating to do RGB - YCoCg conversion + * and back (should be 1 for RGB input) + */ + bool convert_rgb; + u8 slice_count; + /* Slice Width */ + u16 slice_width; + /* Slice Height */ + u16 slice_height; + /* + * 4:2:2 enable mode (from PPS, 4:2:2 conversion happens + * outside of DSC encode/decode algorithm) + */ + bool enable422; + /* Picture Width */ + u16 pic_width; + /* Picture Height */ + u16 pic_height; + /* Offset to bits/group used by RC to determine QP adjustment */ + u8 rc_tgt_offset_high; + /* Offset to bits/group used by RC to determine QP adjustment */ + u8 rc_tgt_offset_low; + /* Bits/pixel target << 4 (ie., 4 fractional bits) */ + u16 bits_per_pixel; + /* + * Factor to determine if an edge is present based + * on the bits produced + */ + u8 rc_edge_factor; + /* Slow down incrementing once the range reaches this value */ + u8 rc_quant_incr_limit1; + /* Slow down incrementing once the range reaches this value */ + u8 rc_quant_incr_limit0; + /* Number of pixels to delay the initial transmission */ + u16 initial_xmit_delay; + /* Number of pixels to delay the VLD on the decoder,not including SSM */ + u16 initial_dec_delay; + /* Block prediction enable */ + bool block_pred_enable; + /* Bits/group offset to use for first line of the slice */ + u8 first_line_bpg_offset; + /* Value to use for RC model offset at slice start */ + u16 initial_offset; + /* Thresholds defining each of the buffer ranges */ + u16 rc_buf_thresh[DSC_NUM_BUF_RANGES - 1]; + /* Parameters for each of the RC ranges */ + struct drm_dsc_rc_range_parameters rc_range_params[DSC_NUM_BUF_RANGES]; + /* Total size of RC model */ + u16 rc_model_size; + /* Minimum QP where flatness information is sent */ + u8 flatness_min_qp; + /* Maximum QP where flatness information is sent */ + u8 flatness_max_qp; + /* Initial value for scale factor */ + u8 initial_scale_value; + /* Decrement scale factor every scale_decrement_interval groups */ + u16 scale_decrement_interval; + /* Increment scale factor every scale_increment_interval groups */ + u16 scale_increment_interval; + /* Non-first line BPG offset to use */ + u16 nfl_bpg_offset; + /* BPG offset used to enforce slice bit */ + u16 slice_bpg_offset; + /* Final RC linear transformation offset value */ + u16 final_offset; + /* Enable on-off VBR (ie., disable stuffing bits) */ + bool vbr_enable; + /* Mux word size (in bits) for SSM mode */ + u8 mux_word_size; + /* + * The (max) size in bytes of the "chunks" that are + * used in slice multiplexing + */ + u16 slice_chunk_size; + /* Rate Control buffer siz in bits */ + u16 rc_bits; + /* DSC Minor Version */ + u8 dsc_version_minor; + /* DSC Major version */ + u8 dsc_version_major; + /* Native 4:2:2 support */ + bool native_422; + /* Native 4:2:0 support */ + bool native_420; + /* Additional bits/grp for seconnd line of slice for native 4:2:0 */ + u8 second_line_bpg_offset; + /* Num of bits deallocated for each grp that is not in second line of slice */ + u16 nsl_bpg_offset; + /* Offset adj fr second line in Native 4:2:0 mode */ + u16 second_line_offset_adj; +};
/** * struct picture_parameter_set - Represents 128 bytes of Picture Parameter Set