Hi,
Am 05.10.2021 um 22:43 schrieb Paul Cercueil paul@crapouillou.net:
Hi Nikolaus,
Le mar., oct. 5 2021 at 14:29:15 +0200, H. Nikolaus Schaller hns@goldelico.com a écrit :
From: Sam Ravnborg sam@ravnborg.org Add DT bindings for the hdmi driver for the Ingenic JZ4780 SoC. Based on .txt binding from Zubair Lutfullah Kakakhel Signed-off-by: Sam Ravnborg sam@ravnborg.org Signed-off-by: H. Nikolaus Schaller hns@goldelico.com Cc: Rob Herring robh@kernel.org Cc: devicetree@vger.kernel.org
.../bindings/display/ingenic-jz4780-hdmi.yaml | 79 +++++++++++++++++++ 1 file changed, 79 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/ingenic-jz4780-hdmi.yaml diff --git a/Documentation/devicetree/bindings/display/ingenic-jz4780-hdmi.yaml b/Documentation/devicetree/bindings/display/ingenic-jz4780-hdmi.yaml new file mode 100644 index 000000000000..5bcb342da86f --- /dev/null +++ b/Documentation/devicetree/bindings/display/ingenic-jz4780-hdmi.yaml @@ -0,0 +1,79 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/ingenic-jz4780-hdmi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml#
+title: Bindings for Ingenic JZ4780 HDMI Transmitter
+maintainers:
- H. Nikolaus Schaller hns@goldelico.com
+description: |
- The HDMI Transmitter in the Ingenic JZ4780 is a Synopsys DesignWare HDMI 1.4
- TX controller IP with accompanying PHY IP.
My dmesg disagrees: dw-hdmi-ingenic 10180000.hdmi: Detected HDMI TX controller v1.31a with HDCP (DWC HDMI 3D TX PHY)
mine as well.
Or am I comparing apples to oranges?
There is a document called "JZ4780 High Efficiency Engine for Mobile Device" (JZ4780_PB.pdf) which says
"24-bit parallel/serial TFT interface, HDMI 1.4a interface, LVDS interface"
And the data sheet ("JZ4780 Mobile Application Processor Data Sheet ") says: "Support HDMI 1.4a Interface"
Finally, the programming manual also says "Support HDMI 1.4a Interface".
So what is correct?
dmesg may return something else. E.g. silicon revision 1.31a while the interface is HDMI protocol revision 1.4a compatible?
Trying to find something about "hdmi 1.31a" did only lead to some "Synopsys' HAPS-51 eval platform" [1].
Looking at HDMI standards [2] I can only find HDMI 1.3 and 1.3a but no HDMI 1.31a.
[1] https://www.digital-cp.com/hdcp-products/haps51-hdmi-tx-platform-dwc-hdmi-tx... [2] https://en.wikipedia.org/wiki/HDMI#Version_1.3
Well it may also be some Synopsys-internal designation 1.31a referring so something newer than HDMI 1.3a which became the HDMI 1.4 standard (released June 2009)...
Whom should we believe? What the chip tells or what the data sheet and programming manual says?
I tend to keep confusion low and stay with "HDMI 1.4" in the bindings because there is no offical "HDMI 1.31a" standard. And HDMI 1.4 was already some years old when the jz4780 was released. So it is likely that the chip identification just returns 1.31a (maybe Ingenic licenced an interim release VHDL) although the standard was later officially named 1.4a.
+allOf:
- $ref: bridge/synopsys,dw-hdmi.yaml#
+properties:
- compatible:
- const: ingenic,jz4780-dw-hdmi
- reg-io-width:
- const: 4
- clocks:
- maxItems: 2
- hdmi-5v-supply:
- description: Optional regulator to provide +5V at the connector
- ddc-i2c-bus:
- description: An I2C interface if the internal DDC I2C driver is not to be used
This property is used within (drivers/gpu/drm/bridge/synopsys/dw-hdmi.c); I think it would make sense to move it to bridge/synopsys,dw-hdmi.yaml.
It is indeed more general and not jz4780 specific. I'll move it for v6.
BR and thanks, Nikolaus