Hi Liu Ying,
On 12/23/2014 04:46 AM, Liu Ying wrote:
This patch adds support for Himax HX8369A MIPI DSI panel.
Signed-off-by: Liu Ying Ying.Liu@freescale.com
v2->v3:
- Sort the included header files alphabetically.
v1->v2:
- Address almost all comments from Thierry Reding.
- Remove several DT properties as they can be implied by the compatible string.
- Add the HIMAX/himax prefixes to the driver's Kconfig name and driver name.
- Move the driver's Makefile entry place to sort the entries alphabetically.
- Reuse several standard DCS functions instead of inventing wheels.
- Move the panel resetting and power logics to the driver probe/remove stages. This may simplify panel prepare/unprepare hooks. The power consumption should not change a lot at DPMS since the panel enters sleep mode at that time.
What kind of issues did you have with reset/power logic in prepare/unprepare? As I see it should be just a matter of moving power on/off functions to prepare/unprepare, am I right?
- Add the module author.
- Other minor changes, such as coding style issues.
.../devicetree/bindings/panel/himax,hx8369a.txt | 41 ++ drivers/gpu/drm/panel/Kconfig | 5 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-himax-hx8369a.c | 573 +++++++++++++++++++++ 4 files changed, 620 insertions(+) create mode 100644 Documentation/devicetree/bindings/panel/himax,hx8369a.txt create mode 100644 drivers/gpu/drm/panel/panel-himax-hx8369a.c
diff --git a/Documentation/devicetree/bindings/panel/himax,hx8369a.txt b/Documentation/devicetree/bindings/panel/himax,hx8369a.txt new file mode 100644 index 0000000..36a2f11 --- /dev/null +++ b/Documentation/devicetree/bindings/panel/himax,hx8369a.txt @@ -0,0 +1,41 @@ +Himax HX8369A WVGA 16.7M color TFT single chip driver with internal GRAM
+Himax HX8369A is a WVGA resolution driving controller. +It is designed to provide a single chip solution that combines a source +driver and power supply circuits to drive a TFT dot matrix LCD with +480RGBx864 dots at the maximum.
+The HX8369A supports several interface modes, including MPU MIPI DBI Type +A/B mode, MIPI DPI/DBI Type C mode, MIPI DSI video mode, MIPI DSI command +mode and MDDI mode. The interface mode is selected by the external hardware +pins BS[3:0].
+Currently, only the MIPI DSI video mode is supported.
+Required properties:
- compatible: should be a panel's compatible string
- reg: the virtual channel number of a DSI peripheral as described in [1]
- reset-gpios: a GPIO spec for the reset pin
+Optional properties:
- vdd1-supply: I/O and interface power supply
- vdd2-supply: analog power supply
- vdd3-supply: logic power supply
- dsi-vcc-supply: DSI and MDDI power supply
- vpp-supply: OTP programming voltage
- bs0-gpios: a GPIO spec for the pin BS0
- bs1-gpios: a GPIO spec for the pin BS1
- bs2-gpios: a GPIO spec for the pin BS2
- bs3-gpios: a GPIO spec for the pin BS3
I wonder if it wouldn't be better to replace it by gpio list, sth like: - bs-gpios: list of four GPIO specs for BS0-BS3 pins
At least documentation suggests it [1], it also allows to omit some pins if necessary, but it is just suggestion.
[1]: Documentation/devicetree/bindings/gpio/gpio.txt
+[1] Documentation/devicetree/bindings/mipi/dsi/mipi-dsi-bus.txt
+Example:
- panel {
compatible = "truly,tft480800-16-e-dsi";reg = <0>;pinctrl-names = "default";pinctrl-0 = <&pinctrl_mipi_panel>;reset-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;bs2-gpios = <&gpio6 14 GPIO_ACTIVE_HIGH>;- };
diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig index 024e98e..81b0bf0 100644 --- a/drivers/gpu/drm/panel/Kconfig +++ b/drivers/gpu/drm/panel/Kconfig @@ -16,6 +16,11 @@ config DRM_PANEL_SIMPLE that it can be automatically turned off when the panel goes into a low power state.
+config DRM_PANEL_HIMAX_HX8369A
- tristate "Himax HX8369A panel"
- depends on OF
- select DRM_MIPI_DSI
config DRM_PANEL_LD9040 tristate "LD9040 RGB/SPI panel" depends on OF && SPI diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile index 4b2a043..d5dbe06 100644 --- a/drivers/gpu/drm/panel/Makefile +++ b/drivers/gpu/drm/panel/Makefile @@ -1,4 +1,5 @@ obj-$(CONFIG_DRM_PANEL_SIMPLE) += panel-simple.o +obj-$(CONFIG_DRM_PANEL_HIMAX_HX8369A) += panel-himax-hx8369a.o obj-$(CONFIG_DRM_PANEL_LD9040) += panel-ld9040.o obj-$(CONFIG_DRM_PANEL_S6E8AA0) += panel-s6e8aa0.o obj-$(CONFIG_DRM_PANEL_SHARP_LQ101R1SX01) += panel-sharp-lq101r1sx01.o diff --git a/drivers/gpu/drm/panel/panel-himax-hx8369a.c b/drivers/gpu/drm/panel/panel-himax-hx8369a.c new file mode 100644 index 0000000..6efce8e --- /dev/null +++ b/drivers/gpu/drm/panel/panel-himax-hx8369a.c @@ -0,0 +1,573 @@ +/*
- Himax HX8369A panel driver.
- Copyright (C) 2011-2014 Freescale Semiconductor, Inc.
- This program is free software; you can redistribute it and/or modify
- it under the terms of the GNU General Public License version 2 as
- published by the Free Software Foundation.
- This driver is based on Samsung s6e8aa0 panel driver.
- */
+#include <drm/drmP.h> +#include <drm/drm_mipi_dsi.h> +#include <drm/drm_panel.h>
+#include <linux/gpio/consumer.h> +#include <linux/of_device.h> +#include <linux/regulator/consumer.h>
+#include <video/mipi_display.h> +#include <video/of_videomode.h> +#include <video/videomode.h>
+#define WRDISBV 0x51 +#define WRCTRLD 0x53 +#define WRCABC 0x55 +#define SETPOWER 0xb1 +#define SETDISP 0xb2 +#define SETCYC 0xb4 +#define SETVCOM 0xb6 +#define SETEXTC 0xb9 +#define SETMIPI 0xba +#define SETPANEL 0xcc +#define SETGIP 0xd5 +#define SETGAMMA 0xe0
+#define HX8369A_MIN_BRIGHTNESS 0x00 +#define HX8369A_MAX_BRIGHTNESS 0xff
+enum hx8369a_mpu_interface {
- HX8369A_DBI_TYPE_A_8BIT,
- HX8369A_DBI_TYPE_A_9BIT,
- HX8369A_DBI_TYPE_A_16BIT,
- HX8369A_DBI_TYPE_A_18BIT,
- HX8369A_DBI_TYPE_B_8BIT,
- HX8369A_DBI_TYPE_B_9BIT,
- HX8369A_DBI_TYPE_B_16BIT,
- HX8369A_DBI_TYPE_B_18BIT,
- HX8369A_DSI_CMD_MODE,
- HX8369A_DBI_TYPE_B_24BIT,
- HX8369A_DSI_VIDEO_MODE,
- HX8369A_MDDI,
- HX8369A_DPI_DBI_TYPE_C_OPT1,
- HX8369A_DPI_DBI_TYPE_C_OPT2,
- HX8369A_DPI_DBI_TYPE_C_OPT3
+};
+enum hx8369a_resolution {
- HX8369A_RES_480_864,
- HX8369A_RES_480_854,
- HX8369A_RES_480_800,
- HX8369A_RES_480_640,
- HX8369A_RES_360_640,
- HX8369A_RES_480_720,
+};
+struct hx8369a_panel_desc {
- const struct drm_display_mode *mode;
- /* ms */
- unsigned int power_on_delay;
- unsigned int reset_delay;
- unsigned int dsi_lanes;
+};
+struct hx8369a {
- struct device *dev;
- struct drm_panel panel;
- const struct hx8369a_panel_desc *pd;
- struct regulator_bulk_data supplies[5];
- struct gpio_desc *reset_gpio;
- struct gpio_desc *bs_gpio[4];
- u8 res_sel;
+};
+static inline struct hx8369a *panel_to_hx8369a(struct drm_panel *panel) +{
- return container_of(panel, struct hx8369a, panel);
+}
+static void hx8369a_dcs_write(struct hx8369a *ctx, const char *func,
const void *data, size_t len)+{
- struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
- ssize_t ret;
- ret = mipi_dsi_dcs_write_buffer(dsi, data, len);
- if (ret < 0)
dev_err(ctx->dev, "%s failed: %d\n", func, ret);
Your only reaction to transmission errors is to log error, no error propagation. I think it is not the best approach. I suggest to implement error propagation either the way I did in s6e8aa0, either the way Thierry suggests. Of course I prefer my method as it significantly reduces code bloat due to error checking, but it is up to you.
+}
+#define hx8369a_dcs_write_seq(ctx, seq...) \ +({ \
- const u8 d[] = { seq }; \
- BUILD_BUG_ON_MSG(ARRAY_SIZE(d) > 64, "DCS sequence too big for stack"); \
- hx8369a_dcs_write(ctx, __func__, d, ARRAY_SIZE(d)); \
+})
+#define hx8369a_dcs_write_seq_static(ctx, seq...) \ +({ \
- static const u8 d[] = { seq }; \
- hx8369a_dcs_write(ctx, __func__, d, ARRAY_SIZE(d)); \
+})
+static void hx8369a_dsi_set_display_related_register(struct hx8369a *ctx) +{
- u8 sec_p = (ctx->res_sel << 4) | 0x03;
- hx8369a_dcs_write_seq(ctx, SETDISP, 0x00, sec_p, 0x03,
0x03, 0x70, 0x00, 0xff, 0x00, 0x00, 0x00, 0x00,0x03, 0x03, 0x00, 0x01);+}
+static void hx8369a_dsi_set_display_waveform_cycle(struct hx8369a *ctx) +{
- hx8369a_dcs_write_seq_static(ctx, SETCYC, 0x00, 0x1d, 0x5f, 0x0e, 0x06);
+}
+static void hx8369a_dsi_set_gip(struct hx8369a *ctx) +{
- hx8369a_dcs_write_seq_static(ctx, SETGIP, 0x00, 0x04, 0x03, 0x00, 0x01,
0x05, 0x1c, 0x70, 0x01, 0x03, 0x00, 0x00, 0x40,0x06, 0x51, 0x07, 0x00, 0x00, 0x41, 0x06, 0x50,0x07, 0x07, 0x0f, 0x04);+}
+static void hx8369a_dsi_set_power(struct hx8369a *ctx) +{
- hx8369a_dcs_write_seq_static(ctx, SETPOWER, 0x01, 0x00, 0x34, 0x06, 0x00,
0x0f, 0x0f, 0x2a, 0x32, 0x3f, 0x3f, 0x07, 0x3a,0x01, 0xe6, 0xe6, 0xe6, 0xe6, 0xe6);+}
+static void hx8369a_dsi_set_vcom_voltage(struct hx8369a *ctx) +{
- hx8369a_dcs_write_seq_static(ctx, SETVCOM, 0x56, 0x56);
+}
+static void hx8369a_dsi_set_panel(struct hx8369a *ctx) +{
- hx8369a_dcs_write_seq_static(ctx, SETPANEL, 0x02);
+}
+static void hx8369a_dsi_set_gamma_curve(struct hx8369a *ctx) +{
- hx8369a_dcs_write_seq_static(ctx, SETGAMMA, 0x00, 0x1d, 0x22, 0x38, 0x3d,
0x3f, 0x2e, 0x4a, 0x06, 0x0d, 0x0f, 0x13, 0x15,0x13, 0x16, 0x10, 0x19, 0x00, 0x1d, 0x22, 0x38,0x3d, 0x3f, 0x2e, 0x4a, 0x06, 0x0d, 0x0f, 0x13,0x15, 0x13, 0x16, 0x10, 0x19);+}
+static void hx8369a_dsi_set_mipi(struct hx8369a *ctx) +{
- u8 eleventh_p = ctx->pd->dsi_lanes == 2 ? 0x11 : 0x10;
- hx8369a_dcs_write_seq(ctx, SETMIPI, 0x00, 0xa0, 0xc6, 0x00, 0x0a, 0x00,
0x10, 0x30, 0x6f, 0x02, eleventh_p, 0x18, 0x40);+}
+static void hx8369a_dsi_set_interface_pixel_fomat(struct hx8369a *ctx) +{
- struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
- u8 format;
- int ret;
- if (dsi->format == MIPI_DSI_FMT_RGB888)
format = 0x77;- else if (dsi->format == MIPI_DSI_FMT_RGB565)
format = 0x55;- else
format = 0x66;
Just nitpick, switch fits better here.
- ret = mipi_dsi_dcs_set_pixel_format(dsi, format);
- if (ret < 0)
dev_err(ctx->dev, "%s failed: %d\n", __func__, ret);+}
+static void hx8369a_dsi_set_column_address(struct hx8369a *ctx) +{
- struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
- const struct drm_display_mode *mode = ctx->pd->mode;
- int ret;
- ret = mipi_dsi_dcs_set_column_address(dsi, 0, mode->hdisplay - 1);
- if (ret < 0)
dev_err(ctx->dev, "%s failed: %d\n", __func__, ret);+}
+static void hx8369a_dsi_set_page_address(struct hx8369a *ctx) +{
- struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
- const struct drm_display_mode *mode = ctx->pd->mode;
- int ret;
- ret = mipi_dsi_dcs_set_page_address(dsi, 0, mode->vdisplay - 1);
- if (ret < 0)
dev_err(ctx->dev, "%s failed: %d\n", __func__, ret);+}
+static void hx8369a_dsi_write_display_brightness(struct hx8369a *ctx, u8 brightness) +{
- hx8369a_dcs_write_seq(ctx, WRDISBV, brightness);
+}
+static void hx8369a_dsi_write_cabc(struct hx8369a *ctx) +{
- hx8369a_dcs_write_seq_static(ctx, WRCABC, 0x01);
+}
+static void hx8369a_dsi_write_control_display(struct hx8369a *ctx) +{
- hx8369a_dcs_write_seq_static(ctx, WRCTRLD, 0x24);
+}
+static void hx8369a_dsi_panel_init(struct hx8369a *ctx) +{
- hx8369a_dsi_set_display_related_register(ctx);
- hx8369a_dsi_set_display_waveform_cycle(ctx);
- hx8369a_dsi_set_gip(ctx);
- hx8369a_dsi_set_power(ctx);
- hx8369a_dsi_set_vcom_voltage(ctx);
- hx8369a_dsi_set_panel(ctx);
- hx8369a_dsi_set_gamma_curve(ctx);
- hx8369a_dsi_set_mipi(ctx);
- hx8369a_dsi_set_interface_pixel_fomat(ctx);
- hx8369a_dsi_set_column_address(ctx);
- hx8369a_dsi_set_page_address(ctx);
- hx8369a_dsi_write_cabc(ctx);
- hx8369a_dsi_write_control_display(ctx);
+}
+static void hx8369a_dsi_set_extension_command(struct hx8369a *ctx) +{
- hx8369a_dcs_write_seq_static(ctx, SETEXTC, 0xff, 0x83, 0x69);
+}
+static void hx8369a_dsi_set_maximum_return_packet_size(struct hx8369a *ctx,
u16 size)+{
- struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
- int ret;
- ret = mipi_dsi_set_maximum_return_packet_size(dsi, size);
- if (ret < 0)
dev_err(ctx->dev,"error %d setting maximum return packet size to %d\n",ret, size);+}
+static int hx8369a_dsi_set_sequence(struct hx8369a *ctx) +{
- struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
- int ret;
- hx8369a_dsi_set_extension_command(ctx);
- hx8369a_dsi_set_maximum_return_packet_size(ctx, 4);
- hx8369a_dsi_panel_init(ctx);
- ret = mipi_dsi_dcs_exit_sleep_mode(dsi);
- if (ret < 0) {
dev_err(ctx->dev, "failed to exit sleep mode: %d\n", ret);return ret;- }
- ret = mipi_dsi_dcs_set_display_on(dsi);
- if (ret < 0) {
dev_err(ctx->dev, "failed to set display on: %d\n", ret);return ret;- }
- /*
* It's necessary to wait 120msec after sending the Sleep Out* command before Sleep In command can be sent, according to* the HX8369A data sheet.*/- msleep(120);
- return 0;
+}
+static int hx8369a_dsi_disable(struct drm_panel *panel) +{
- struct hx8369a *ctx = panel_to_hx8369a(panel);
- hx8369a_dsi_write_display_brightness(ctx, HX8369A_MIN_BRIGHTNESS);
- return 0;
+}
+static int hx8369a_dsi_unprepare(struct drm_panel *panel) +{
- struct hx8369a *ctx = panel_to_hx8369a(panel);
- struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
- int ret;
- ret = mipi_dsi_dcs_enter_sleep_mode(dsi);
- if (ret < 0) {
dev_err(ctx->dev, "failed to enter sleep mode: %d\n", ret);return ret;- }
- ret = mipi_dsi_dcs_set_display_off(dsi);
- if (ret < 0) {
dev_err(ctx->dev, "failed to set display off: %d\n", ret);return ret;- }
- /*
* This is to allow time for the supply voltages and clock* circuits to stablize, according to the HX8369A data sheet.*/- msleep(5);
- return ret;
+}
+static int hx8369a_dsi_prepare(struct drm_panel *panel) +{
- struct hx8369a *ctx = panel_to_hx8369a(panel);
- return hx8369a_dsi_set_sequence(ctx);
+}
+static int hx8369a_dsi_enable(struct drm_panel *panel) +{
- struct hx8369a *ctx = panel_to_hx8369a(panel);
- hx8369a_dsi_write_display_brightness(ctx, HX8369A_MAX_BRIGHTNESS);
- return 0;
+}
+static int hx8369a_get_modes(struct drm_panel *panel) +{
- struct drm_connector *connector = panel->connector;
- struct drm_device *drm = panel->drm;
- struct hx8369a *ctx = panel_to_hx8369a(panel);
- struct drm_display_mode *mode;
- const struct drm_display_mode *m = ctx->pd->mode;
- mode = drm_mode_duplicate(drm, m);
- if (!mode) {
dev_err(drm->dev, "failed to add mode %ux%u@%u\n",m->hdisplay, m->vdisplay, m->vrefresh);return 0;- }
- drm_mode_set_name(mode);
- mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
- connector->display_info.bpc = 8;
- connector->display_info.width_mm = mode->width_mm;
- connector->display_info.height_mm = mode->height_mm;
- drm_mode_probed_add(connector, mode);
- return 1;
+}
+static const struct drm_panel_funcs hx8369a_dsi_drm_funcs = {
- .disable = hx8369a_dsi_disable,
- .unprepare = hx8369a_dsi_unprepare,
- .prepare = hx8369a_dsi_prepare,
- .enable = hx8369a_dsi_enable,
- .get_modes = hx8369a_get_modes,
+};
+static int hx8369a_power_on(struct hx8369a *ctx) +{
- int ret;
- ret = regulator_bulk_enable(ARRAY_SIZE(ctx->supplies), ctx->supplies);
- if (ret < 0)
return ret;- msleep(ctx->pd->power_on_delay);
- gpiod_set_value(ctx->reset_gpio, 1);
- usleep_range(50, 60);
- gpiod_set_value(ctx->reset_gpio, 0);
- msleep(ctx->pd->reset_delay);
- return 0;
+}
+static int hx8369a_power_off(struct hx8369a *ctx) +{
- return regulator_bulk_disable(ARRAY_SIZE(ctx->supplies), ctx->supplies);;
+}
+static int hx8369a_vm_to_res_sel(struct hx8369a *ctx) +{
- const struct drm_display_mode *mode = ctx->pd->mode;
- switch (mode->hdisplay) {
- case 480:
switch (mode->vdisplay) {case 864:ctx->res_sel = HX8369A_RES_480_864;break;case 854:ctx->res_sel = HX8369A_RES_480_854;break;case 800:ctx->res_sel = HX8369A_RES_480_800;break;case 640:ctx->res_sel = HX8369A_RES_480_640;break;case 720:ctx->res_sel = HX8369A_RES_480_720;break;default:break;}break;- case 360:
if (mode->vdisplay == 640)ctx->res_sel = HX8369A_RES_360_640;break;- default:
break;- }
- return 0;
+}
Function always returns 0, you can make it void, or return error in case mode is not supported. As I see the mode is hardcoded in the driver so the 1st solutions fits here better.
+static const struct drm_display_mode truly_tft480800_16_e_mode = {
- .clock = 26400,
- .hdisplay = 480,
- .hsync_start = 480 + 8,
- .hsync_end = 480 + 8 + 8,
- .htotal = 480 + 8 + 8 + 8,
- .vdisplay = 800,
- .vsync_start = 800 + 6,
- .vsync_end = 800 + 6 + 6,
- .vtotal = 800 + 6 + 6 + 6,
- .vrefresh = 60,
- .width_mm = 45,
- .height_mm = 76,
+};
+static const struct hx8369a_panel_desc truly_tft480800_16_e_dsi = {
- .mode = &truly_tft480800_16_e_mode,
- .power_on_delay = 10,
- .reset_delay = 10,
- .dsi_lanes = 2,
+};
+static const struct of_device_id hx8369a_dsi_of_match[] = {
- {
.compatible = "truly,tft480800-16-e-dsi",.data = &truly_tft480800_16_e_dsi,- }, {
/* sentinel */- },
+}; +MODULE_DEVICE_TABLE(of, hx8369a_dsi_of_match);
+static int hx8369a_dsi_probe(struct mipi_dsi_device *dsi) +{
- struct device *dev = &dsi->dev;
- const struct of_device_id *of_id =
of_match_device(hx8369a_dsi_of_match, dev);- struct hx8369a *ctx;
- int ret, i;
- char bs[4];
- ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
- if (!ctx)
return -ENOMEM;- ctx->dev = dev;
- if (of_id) {
ctx->pd = of_id->data;- } else {
dev_err(dev, "cannot find compatible device\n");return -ENODEV;- }
- ret = hx8369a_vm_to_res_sel(ctx);
- if (ret < 0)
return ret;
We know it will always succeed, don't we?
- ctx->supplies[0].supply = "vdd1";
- ctx->supplies[1].supply = "vdd2";
- ctx->supplies[2].supply = "vdd3";
- ctx->supplies[3].supply = "dsi-vcc";
- ctx->supplies[4].supply = "vpp";
- ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(ctx->supplies),
ctx->supplies);- if (ret < 0) {
dev_err(dev, "failed to get regulators: %d\n", ret);
Just nitpicking, here and later, in case of deferred probing you will have error logged, but it should be at most dev_info.
return ret;- }
- ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
- if (IS_ERR(ctx->reset_gpio)) {
dev_err(dev, "cannot get reset-gpios %ld\n",PTR_ERR(ctx->reset_gpio));return PTR_ERR(ctx->reset_gpio);- }
- for (i = 0; i < 4; i++) {
snprintf(bs, sizeof(bs), "bs%d", i);ctx->bs_gpio[i] = devm_gpiod_get(dev, bs, GPIOD_OUT_HIGH);dev_dbg(dev, "bs%d-gpio is configured\n", i);- }
- ret = hx8369a_power_on(ctx);
- if (ret < 0) {
dev_err(dev, "cannot power on\n");return ret;- }
- drm_panel_init(&ctx->panel);
- ctx->panel.dev = dev;
- ctx->panel.funcs = &hx8369a_dsi_drm_funcs;
- ret = drm_panel_add(&ctx->panel);
- if (ret < 0)
return ret;- mipi_dsi_set_drvdata(dsi, ctx);
- dsi->channel = 0;
- dsi->lanes = ctx->pd->dsi_lanes;
- dsi->format = MIPI_DSI_FMT_RGB888;
- dsi->mode_flags = MIPI_DSI_MODE_VIDEO |
MIPI_DSI_MODE_VIDEO_BURST |MIPI_DSI_MODE_VIDEO_SYNC_PULSE;- ret = mipi_dsi_attach(dsi);
- if (ret < 0)
drm_panel_remove(&ctx->panel);- return ret;
+}
+static int hx8369a_dsi_remove(struct mipi_dsi_device *dsi) +{
- struct hx8369a *ctx = mipi_dsi_get_drvdata(dsi);
- mipi_dsi_detach(dsi);
- drm_panel_remove(&ctx->panel);
- return hx8369a_power_off(ctx);
The sequence here is OK, but as I lurked into dsi host code[1] it seems dsi host lacks synchronization with drm in dw_mipi_dsi_host_detach before removing the panel, but it should be fixed in the host controller.
[1]: [PATCH RFC v4 12/21] drm/bridge: Add Synopsys DesignWare MIPI DSI host controller driver
Regards Andrzej
+}
+static struct mipi_dsi_driver hx8369a_dsi_driver = {
- .probe = hx8369a_dsi_probe,
- .remove = hx8369a_dsi_remove,
- .driver = {
.name = "panel-hx8369a-dsi",.of_match_table = hx8369a_dsi_of_match,- },
+}; +module_mipi_dsi_driver(hx8369a_dsi_driver);
+MODULE_DESCRIPTION("Himax HX8369A panel driver"); +MODULE_AUTHOR("Liu Ying Ying.Liu@freescale.com"); +MODULE_LICENSE("GPL v2");