On Fri, Jan 26, 2018 at 02:16:51PM +0100, Thierry Escande wrote:
From: Lin Huang hl@rock-chips.com
AUX errors are caused by many different reasons. We may not know what happened in aux channel on failure, so let's reset aux channel if some errors occurred.
Cc: 征增 王 wzz@rock-chips.com Cc: Douglas Anderson dianders@chromium.org Signed-off-by: Lin Huang hl@rock-chips.com Signed-off-by: Sean Paul seanpaul@chromium.org Signed-off-by: Thierry Escande thierry.escande@collabora.com Reviewed-by: Andrzej Hajda a.hajda@samsung.com
drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c | 18 ++++++++++++++---- 1 file changed, 14 insertions(+), 4 deletions(-)
diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c index dee1ba109b5f..7b7fd227e1f9 100644 --- a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c +++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c @@ -466,6 +466,10 @@ void analogix_dp_init_aux(struct analogix_dp_device *dp) reg = RPLY_RECEIV | AUX_ERR; writel(reg, dp->reg_base + ANALOGIX_DP_INT_STA);
- analogix_dp_set_analog_power_down(dp, AUX_BLOCK, true);
- usleep_range(10, 11);
This is kind of lame. I don't think this needs to be _exactly_ 10us, even 10/20 would be an improvement. Since this is so infrequent, it's not a dealbreaker either way, I guess.
Sean
analogix_dp_set_analog_power_down(dp, AUX_BLOCK, false);
analogix_dp_reset_aux(dp);
/* Disable AUX transaction H/W retry */
@@ -1159,7 +1163,7 @@ ssize_t analogix_dp_transfer(struct analogix_dp_device *dp, reg, !(reg & AUX_EN), 25, 500 * 1000); if (ret) { dev_err(dp->dev, "AUX CH enable timeout!\n");
return -ETIMEDOUT;
goto aux_error;}
/* TODO: Wait for an interrupt instead of looping? */
@@ -1168,7 +1172,7 @@ ssize_t analogix_dp_transfer(struct analogix_dp_device *dp, reg, reg & RPLY_RECEIV, 10, 20 * 1000); if (ret) { dev_err(dp->dev, "AUX CH cmd reply timeout!\n");
return -ETIMEDOUT;
goto aux_error;}
/* Clear interrupt source for AUX CH command reply */
@@ -1178,7 +1182,7 @@ ssize_t analogix_dp_transfer(struct analogix_dp_device *dp, reg = readl(dp->reg_base + ANALOGIX_DP_INT_STA); if (reg & AUX_ERR) { writel(AUX_ERR, dp->reg_base + ANALOGIX_DP_INT_STA);
return -EREMOTEIO;
goto aux_error;}
/* Check AUX CH error access status */
@@ -1186,7 +1190,7 @@ ssize_t analogix_dp_transfer(struct analogix_dp_device *dp, if ((reg & AUX_STATUS_MASK)) { dev_err(dp->dev, "AUX CH error happened: %d\n\n", reg & AUX_STATUS_MASK);
return -EREMOTEIO;
goto aux_error;}
if (msg->request & DP_AUX_I2C_READ) {
@@ -1212,4 +1216,10 @@ ssize_t analogix_dp_transfer(struct analogix_dp_device *dp, msg->reply = DP_AUX_NATIVE_REPLY_ACK;
return num_transferred > 0 ? num_transferred : -EBUSY;
+aux_error:
- /* if aux err happen, reset aux */
- analogix_dp_init_aux(dp);
- return -EREMOTEIO;
}
2.14.1