Update the bindings with the new properties used for PMI8998.
Signed-off-by: Kiran Gunda kgunda@codeaurora.org --- Changes from V3: - Removed the default values. - Removed pmi8998 example.
.../bindings/leds/backlight/qcom-wled.txt | 76 ++++++++++++++++++---- 1 file changed, 62 insertions(+), 14 deletions(-)
diff --git a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt index 14f28f2..3f22ced 100644 --- a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt +++ b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt @@ -20,8 +20,7 @@ platforms. The PMIC is connected to the host processor via SPMI bus. - default-brightness Usage: optional Value type: <u32> - Definition: brightness value on boot, value from: 0-4095 - Default: 2048 + Definition: brightness value on boot, value from: 0-4095.
- label Usage: required @@ -48,20 +47,24 @@ platforms. The PMIC is connected to the host processor via SPMI bus. - qcom,current-limit Usage: optional Value type: <u32> - Definition: mA; per-string current limit - value: For pm8941: from 0 to 25 with 5 mA step - Default 20 mA. - For pmi8998: from 0 to 30 with 5 mA step - Default 25 mA. + Definition: mA; per-string current limit; value from 0 to 25 with + 1 mA step. + This property is supported only for pm8941. + +- qcom,current-limit-microamp + Usage: optional + Value type: <u32> + Definition: uA; per-string current limit; value from 0 to 30000 with + 2500 uA step.
- qcom,current-boost-limit Usage: optional Value type: <u32> Definition: mA; boost current limit. For pm8941: one of: 105, 385, 525, 805, 980, 1260, 1400, - 1680. Default: 805 mA + 1680. For pmi8998: one of: 105, 280, 450, 620, 970, 1150, 1300, - 1500. Default: 970 mA + 1500.
- qcom,switching-freq Usage: optional @@ -69,22 +72,66 @@ platforms. The PMIC is connected to the host processor via SPMI bus. Definition: kHz; switching frequency; one of: 600, 640, 685, 738, 800, 872, 960, 1066, 1200, 1371, 1600, 1920, 2400, 3200, 4800, 9600. - Default: for pm8941: 1600 kHz - for pmi8998: 800 kHz
- qcom,ovp Usage: optional Value type: <u32> Definition: V; Over-voltage protection limit; one of: - 27, 29, 32, 35. default: 29V + 27, 29, 32, 35. This property is supported only for PM8941.
+- qcom,ovp-millivolt + Usage: optional + Value type: <u32> + Definition: mV; Over-voltage protection limit; + For pmi8998: one of 18100, 19600, 29600, 31100 + If this property is not specified for PM8941, it + falls back to "qcom,ovp" property. + - qcom,num-strings Usage: optional Value type: <u32> Definition: #; number of led strings attached; - value from 1 to 3. default: 2 - This property is supported only for PM8941. + value: For PM8941 from 1 to 3. + For PMI8998 from 1 to 4. + +- interrupts + Usage: optional + Value type: <prop encoded array> + Definition: Interrupts associated with WLED. This should be + "short" and "ovp" interrupts. Interrupts can be + specified as per the encoding listed under + Documentation/devicetree/bindings/spmi/ + qcom,spmi-pmic-arb.txt. + +- interrupt-names + Usage: optional + Value type: <string> + Definition: Interrupt names associated with the interrupts. + Must be "short" and "ovp". The short circuit detection + is not supported for PM8941. + +- qcom,enabled-strings + Usage: optional + Value tyoe: <u32 array> + Definition: Array of the WLED strings numbered from 0 to 3. Each + string of leds are operated individually. Specify the + list of strings used by the device. Any combination of + led strings can be used. + +- qcom,external-pfet + Usage: optional + Value type: <bool> + Definition: Specify if external PFET control for short circuit + protection is used. This property is supported only + for PMI8998. + +- qcom,auto-string-detection + Usage: optional + Value type: <bool> + Definition: Enables auto-detection of the WLED string configuration. + This feature is not supported for PM8941. +
Example:
@@ -99,4 +146,5 @@ pm8941-wled@d800 { qcom,switching-freq = <1600>; qcom,ovp = <29>; qcom,num-strings = <2>; + qcom,enabled-strings = <0x00 0x01>; };