On Wed, Dec 09, 2020 at 02:28:18PM -0600, Bjorn Andersson wrote:
On Tue 08 Dec 17:52 CST 2020, Daniel Vetter wrote:
On Tue, Dec 08, 2020 at 04:02:16PM -0600, Bjorn Andersson wrote:
On Tue 08 Dec 06:47 CST 2020, Thierry Reding wrote:
On Mon, Dec 07, 2020 at 10:44:46PM -0600, Bjorn Andersson wrote:
Some bridge chips, such as the TI SN65DSI86 DSI/eDP bridge, provides means of generating a PWM signal for backlight control of the attached panel. The provided PWM chip is typically controlled by the pwm-backlight driver, which if tied to the panel will provide DPMS.
But with the current implementation the panel will refuse to probe because the bridge driver has yet to probe and register the PWM chip, and the bridge driver will refuse to probe because it's unable to find the panel.
What you're describing is basically a circular dependency. Can't we get rid of that in some other way? Why exactly does the bridge driver refuse to probe if the panel can't be found?
In other words, I see how the bridge would /use/ the panel in that it forward a video stream to it. But how does the panel /use/ the bridge?
Yes, this is indeed a circular dependency between the components.
The involved parts are:
- the bridge driver that implements the PWM chip probe defers on drm_of_find_panel_or_bridge() failing to find the panel.
- the pwm-backlight driver that consumes the PWM channel probe defer because the pwm_chip was not registered by the bridge.
- the panel that uses the backlight for DPMS purposes probe defer because drm_panel_of_backlight() fails to find the pwm-backlight.
I looked at means of postponing drm_of_find_panel_or_bridge() to drm_bridge_funcs->attach(), but at that time "deferral" would be fatal. I looked at registering the pwm_chip earlier, but that would depend on a guarantee of the pwm-backlight and panel driver to probe concurrently. And the current solution of not tying the backlight to the panel means that when userspace decides to DPMS the display the backlight stays on.
The proposed solution (hack?) means that DPMS operations happening before the pwm-backlight has probed will be missed, so it's not perfect. It does however allow the backlight on my laptop to turn off, which is a big improvement.
But I'm certainly welcome to suggestions.
Entirely hand-waving, why doesn't the following work:
- driver for the platform device which is the bridge loads
- that platform driver registers the pwm
- it registers some magic for later on (more below)
- panel driver has deferred loading until step 2 happened
- panel driver registers drm_panel
- the magic from step 3 picks up (after having been deferred for a few
times probably) grabs the panel, and sets up the actual drm_bridge driver
Everyone happy, or not? From the description it looks like the problem that the pwm that we need for the backlight is tied to the same driver as the drm_bridge, and always torn down too if the drm_bridge setup fails somehow for a reason. And that reason is the circular dependency this creates.
Now for the magic in step 3, there's options:
- change DT to split out that pwm as a separate platform_device, that way bridge and panel can load indepedently (hopefully)
This is an i2c device, so describing it multiple times would mean we have multiple devices with the same address...
- convert bridge to a multi-function device (mfd), essentially a way to instantiate more devices with their drivers at runtime. Then the actual pwm and drm_bridge parts of your bridge driver bind against those sub-functions, and can defer indepedently
But, this sounds reasonable and would rely on the existing probe deferral logic and if there's ever any improvements in this area we would directly benefit from it.
- we could create a callback/wait function for "pls wait for any panel to show up". Then your bridge driver could launch a work_struct with that wait function, which will do the bridge setup once the panel has shown up. The pwm will be registered right away. It's essentially hand-rolling EPROBE_DEFERRED for work_struct in drm/panel. Maybe we might even have that exported from the driver core, e.g.
register_bridge_fn(struct work *) { do_wait_probe_defer(); panel = drm_of_find_panel_or_bridge(); if (!panel) { schedule_work(); /* want to restart the work so it can be stopped on driver unload */ return; }
/* we have the panel now, register drm_bridge */ }
- cobble something together with component.c, but that's more for collecting unrelated struct device into a logical one than splitting it up more.
tldr; I think you can split this loop here at the bridge by untangling the pwm from the drm_bridge part sufficiently.
Yes, it seems like a reasonable path forward. But I wanted some input before refactoring the whole thing.
Yeah it's unfortunately a bit of work. But I think it's the proper approach since EPROBE_DEFERRED is fundamentally linked to struct device and bound drivers. So we do need a struct device for every part in our dependency graph to make sure we can resolve the dependencies all correctly with reprobing. -Daniel