Hi Dillon
When trying to applying this patch using "git am --3 <patch>" i got this error :
error: cannot convert from y to UTF-8 fatal: could not parse patch
Whereas i got no similar error with the other patch 2/3 and 4.
I find a way to apply it anyway.
Patrice
On 5/14/21 1:02 PM, dillon.minfei@gmail.com wrote:
From: Dillon Min dillon.minfei@gmail.com
This driver combine tiny/ili9341.c mipi_dbi_interface driver with mipi_dpi_interface driver, can support ili9341 with serial mode or parallel rgb interface mode by register configuration.
Reviewed-by: Linus Walleij linus.walleij@linaro.org Link: https://lore.kernel.org/lkml/1590378348-8115-7-git-send-email-dillon.minfei@... Signed-off-by: Dillon Min dillon.minfei@gmail.com
drivers/gpu/drm/panel/Kconfig | 12 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-ilitek-ili9341.c | 1285 ++++++++++++++++++++++++++ 3 files changed, 1298 insertions(+) create mode 100755 drivers/gpu/drm/panel/panel-ilitek-ili9341.c
diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig index 4894913936e9..e4babba17864 100644 --- a/drivers/gpu/drm/panel/Kconfig +++ b/drivers/gpu/drm/panel/Kconfig @@ -123,6 +123,18 @@ config DRM_PANEL_ILITEK_IL9322 Say Y here if you want to enable support for Ilitek IL9322 QVGA (320x240) RGB, YUV and ITU-T BT.656 panels.
+config DRM_PANEL_ILITEK_ILI9341
- tristate "Ilitek ILI9341 240x320 QVGA panels"
- depends on OF && SPI
- depends on DRM_KMS_HELPER
- depends on DRM_KMS_CMA_HELPER
- depends on BACKLIGHT_CLASS_DEVICE
- select DRM_MIPI_DBI
- help
Say Y here if you want to enable support for Ilitek IL9341QVGA (240x320) RGB panels. support serial & parallel rgbinterface.config DRM_PANEL_ILITEK_ILI9881C tristate "Ilitek ILI9881C-based panels" depends on OF diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile index cae4d976c069..0ecde184665d 100644 --- a/drivers/gpu/drm/panel/Makefile +++ b/drivers/gpu/drm/panel/Makefile @@ -11,6 +11,7 @@ obj-$(CONFIG_DRM_PANEL_ELIDA_KD35T133) += panel-elida-kd35t133.o obj-$(CONFIG_DRM_PANEL_FEIXIN_K101_IM2BA02) += panel-feixin-k101-im2ba02.o obj-$(CONFIG_DRM_PANEL_FEIYANG_FY07024DI26A30D) += panel-feiyang-fy07024di26a30d.o obj-$(CONFIG_DRM_PANEL_ILITEK_IL9322) += panel-ilitek-ili9322.o +obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9341) += panel-ilitek-ili9341.o obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9881C) += panel-ilitek-ili9881c.o obj-$(CONFIG_DRM_PANEL_INNOLUX_P079ZCA) += panel-innolux-p079zca.o obj-$(CONFIG_DRM_PANEL_JDI_LT070ME05000) += panel-jdi-lt070me05000.o diff --git a/drivers/gpu/drm/panel/panel-ilitek-ili9341.c b/drivers/gpu/drm/panel/panel-ilitek-ili9341.c new file mode 100644 index 000000000000..f84983cbb250 --- /dev/null +++ b/drivers/gpu/drm/panel/panel-ilitek-ili9341.c @@ -0,0 +1,1285 @@ +// SPDX-License-Identifier: GPL-2.0-only +/*
- Ilitek ILI9341 TFT LCD drm_panel driver.
- This panel can be configured to support:
- 16-bit parallel RGB interface
- 18-bit parallel RGB interface
- 4-line serial spi interface
- Copyright (C) 2020 Dillon Min dillon.minfei@gmail.com
- Derived from drivers/drm/gpu/panel/panel-ilitek-ili9322.c
- */
+#include <linux/bitops.h> +#include <linux/gpio/consumer.h> +#include <linux/module.h> +#include <linux/of_device.h> +#include <linux/regulator/consumer.h> +#include <linux/spi/spi.h> +#include <linux/delay.h> +#include <video/mipi_display.h> +#include <drm/drm_mipi_dbi.h> +#include <drm/drm_gem_framebuffer_helper.h> +#include <drm/drm_gem_cma_helper.h> +#include <drm/drm_fb_helper.h> +#include <drm/drm_gem_atomic_helper.h> +#include <drm/drm_atomic_helper.h>
+#include <drm/drm_drv.h> +#include <drm/drm_modes.h> +#include <drm/drm_panel.h> +#include <drm/drm_print.h>
+#define ILI9341_RGB_INTERFACE 0xb0 /* RGB Interface Signal Control */ +#define ILI9341_FRC 0xb1 /* Frame Rate Control register */ +#define ILI9341_DFC 0xb6 /* Display Function Control register */ +#define ILI9341_POWER1 0xc0 /* Power Control 1 register */ +#define ILI9341_POWER2 0xc1 /* Power Control 2 register */ +#define ILI9341_VCOM1 0xc5 /* VCOM Control 1 register */ +#define ILI9341_VCOM2 0xc7 /* VCOM Control 2 register */ +#define ILI9341_POWERA 0xcb /* Power control A register */ +#define ILI9341_POWERB 0xcf /* Power control B register */ +#define ILI9341_PGAMMA 0xe0 /* Positive Gamma Correction register */ +#define ILI9341_NGAMMA 0xe1 /* Negative Gamma Correction register */ +#define ILI9341_DTCA 0xe8 /* Driver timing control A */ +#define ILI9341_DTCB 0xea /* Driver timing control B */ +#define ILI9341_POWER_SEQ 0xed /* Power on sequence register */ +#define ILI9341_3GAMMA_EN 0xf2 /* 3 Gamma enable register */ +#define ILI9341_INTERFACE 0xf6 /* Interface control register */ +#define ILI9341_PRC 0xf7 /* Pump ratio control register */ +#define ILI9341_ETMOD 0xb7 /* Entry mode set */
+#define ILI9341_MADCTL_BGR BIT(3) +#define ILI9341_MADCTL_MV BIT(5) +#define ILI9341_MADCTL_MX BIT(6) +#define ILI9341_MADCTL_MY BIT(7)
+#define ILI9341_POWER_B_LEN 3 +#define ILI9341_POWER_SEQ_LEN 4 +#define ILI9341_DTCA_LEN 3 +#define ILI9341_DTCB_LEN 2 +#define ILI9341_POWER_A_LEN 5 +#define ILI9341_DFC_1_LEN 2 +#define ILI9341_FRC_LEN 2 +#define ILI9341_VCOM_1_LEN 2 +#define ILI9341_DFC_2_LEN 4 +#define ILI9341_COLUMN_ADDR_LEN 4 +#define ILI9341_PAGE_ADDR_LEN 4 +#define ILI9341_INTERFACE_LEN 3 +#define ILI9341_PGAMMA_LEN 15 +#define ILI9341_NGAMMA_LEN 15 +#define ILI9341_CA_LEN 3
+#define ILI9341_PIXEL_DPI_16_BITS (BIT(6)|BIT(4)) +#define ILI9341_PIXEL_DPI_18_BITS (BIT(6)|BIT(5)) +#define ILI9341_GAMMA_CURVE_1 BIT(0) +#define ILI9341_IF_WE_MODE BIT(0) +#define ILI9341_IF_BIG_ENDIAN 0x00 +#define ILI9341_IF_DM_RGB BIT(2) +#define ILI9341_IF_DM_INTERNAL 0x00 +#define ILI9341_IF_DM_VSYNC BIT(3) +#define ILI9341_IF_RM_RGB BIT(1) +#define ILI9341_IF_RIM_RGB 0x00
+#define ILI9341_COLUMN_ADDR 0x00ef +#define ILI9341_PAGE_ADDR 0x013f
+#define ILI9341_RGB_EPL BIT(0) +#define ILI9341_RGB_DPL BIT(1) +#define ILI9341_RGB_HSPL BIT(2) +#define ILI9341_RGB_VSPL BIT(3) +#define ILI9341_RGB_DE_MODE BIT(6) +#define ILI9341_RGB_DISP_PATH_MEM BIT(7)
+#define ILI9341_DBI_VCOMH_4P6V 0x23 +#define ILI9341_DBI_PWR_2_DEFAULT 0x10 +#define ILI9341_DBI_PRC_NORMAL 0x20 +#define ILI9341_DBI_VCOM_1_VMH_4P25V 0x3e +#define ILI9341_DBI_VCOM_1_VML_1P5V 0x28 +#define ILI9341_DBI_VCOM_2_DEC_58 0x86 +#define ILI9341_DBI_FRC_DIVA 0x00 +#define ILI9341_DBI_FRC_RTNA 0x1b +#define ILI9341_DBI_EMS_GAS BIT(0) +#define ILI9341_DBI_EMS_DTS BIT(1) +#define ILI9341_DBI_EMS_GON BIT(2) +/**
- ili9341_command - ili9341 command with optional parameter(s)
- @ili: struct ili9341
- @cmd: Command
- @seq...: Optional parameter(s)
- Send command to the controller.
- Returns:
- Zero on success, negative error code on failure.
- */
+#define ili9341_command(ili, cmd, seq...) \ +({ \
- u8 d[] = { seq }; \
- _ili9341_command(ili, cmd, d, ARRAY_SIZE(d)); \
+})
+/**
- struct ili9341_config - the system specific ILI9341 configuration
- @max_spi_speed: 10000000
- */
+struct ili9341_config {
- u32 max_spi_speed;
- /** @mode: the drm display mode */
- const struct drm_display_mode mode;
- /** @ca: TODO: need comments for this register */
- u8 ca[ILI9341_CA_LEN];
- /** @power_b: TODO: need comments for this register */
- u8 power_b[ILI9341_POWER_B_LEN];
- /** @power_seq: TODO: need comments for this register */
- u8 power_seq[ILI9341_POWER_SEQ_LEN];
- /** @dtca: TODO: need comments for this register */
- u8 dtca[ILI9341_DTCA_LEN];
- /** @dtcb: TODO: need comments for this register */
- u8 dtcb[ILI9341_DTCB_LEN];
- /** @power_a: TODO: need comments for this register */
- u8 power_a[ILI9341_POWER_A_LEN];
- /** @frc: Frame Rate Control (In Normal Mode/Full Colors) (B1h) */
- /*
* Formula to calculate frame frequency:* Frame Rate=fosc/(Clocks per line x Division ratio x* (Lines+VBP+VFP))** Sets the division ratio for internal clocks of Normal mode at MCU* interface.** fosc : internal oscillator frequency* Clocks per line : RTNA setting* Division ratio : DIVA setting* Lines : total driving line number* VBP : back porch line number* VFP : front porch line number** RTNA [4:0] Frame Rate (Hz) RTNA [4:0] Frame Rate (Hz)* 1 0 0 0 0 119 1 1 0 0 0 79* 1 0 0 0 1 112 1 1 0 0 1 76* 1 0 0 1 0 106 1 1 0 1 0 73* 1 0 0 1 1 100 1 1 0 1 1 70(default)* 1 0 1 0 0 95 1 1 1 0 0 68* 1 0 1 0 1 90 1 1 1 0 1 65* 1 0 1 1 0 86 1 1 1 0 1 63* 1 0 1 1 1 83 1 1 1 1 1 61** DIVA [1:0] : division ratio for internal clocks when Normal mode.** DIVA [1:0] Division Ratio* 0 0 fosc* 0 1 fosc / 2* 1 0 fosc / 4* 1 1 fosc / 8**/- u8 frc[ILI9341_FRC_LEN];
- /** @prc: TODO: need comments for this register */
- u8 prc;
- /** @dfc_1: B6h DISCTRL (Display Function Control) */
- /* D/CX RDX WRX D17-8 D7 D6 D5 D4 D3 D2 D1 D0 HEX
* Command 0 1 M XX 1 0 1 1 0 1 1 0 B6h* 1st Parameter 1 1 M XX 0 0 0 0 PTG[1:0] PT[1:0] 0A* 2nd Parameter 1 1 M XX REV GS SS SM ISC[3:0] 82* 3rd Parameter 1 1 M XX 0 0 NL[5:0] 27* 4th Parameter 1 1 M XX 0 0 PCDIV[5:0] XX** PTG [1:0]: Set the scan mode in non-display area.* PTG1 | PTG0 | Gate outputs in | Source outputs in | VCOM output* non-display area | non-display area |* 1 0 Interval scan Set with the PT[2:0] bits** PT [1:0]: Determine source/VCOM output in a non-display area in the* partial display mode.* 1 0 AGND AGND AGND AGND** REV: Select whether the liquid crystal type is normally white type* or normally black type.* REV Liquid crystal type* 0 Normally black* 1 Normally white** SS: Select the shift direction of outputs from the source driver.* SS Source Output Scan Direction* 0 S1 -> S720* 1 S720 -> S1** GS: Sets the direction of scan by the gate driver in the range* determined by SCN [4:0] and NL [4:0]. The scan direction* determined by GS = 0 can be reversed by setting GS = 1.** GS Gate Output Scan Direction* 0 G1 -> G320* 1 G320 -> G1*/- u8 dfc_1[ILI9341_DFC_1_LEN];
/** @power_1: Power Control 1 (C0h) *//* VRH [5:0]: Set the GVDD level, which is a reference level for the* VCOM level and the grayscale voltage level.** VRH[5:0] GVDD VRH[5:0] GVDD* 0 0 0 0 0 0 Setting prohibited 1 0 0 0 0 0 4.45 V* 0 0 0 0 0 1 Setting prohibited 1 0 0 0 0 1 4.50 V* 0 0 0 0 1 0 Setting prohibited 1 0 0 0 1 0 4.55 V* 0 0 0 0 1 1 3.00 V 1 0 0 0 1 1 4.60 V* 0 0 0 1 0 0 3.05 V 1 0 0 1 0 0 4.65 V* 0 0 0 1 0 1 3.10 V 1 0 0 1 0 1 4.70 V* 0 0 0 1 1 0 3.15 V 1 0 0 1 1 0 4.75 V* 0 0 0 1 1 1 3.20 V 1 0 0 1 1 1 4.80 V* 0 0 1 0 0 0 3.25 V 1 0 1 0 0 0 4.85 V* 0 0 1 0 0 1 3.30 V 1 0 1 0 0 1 4.90 V* 0 0 1 0 1 0 3.35 V 1 0 1 0 1 0 4.95 V* 0 0 1 0 1 1 3.40 V 1 0 1 0 1 1 5.00 V* 0 0 1 1 0 0 3.45 V 1 0 1 1 0 0 5.05 V* 0 0 1 1 0 1 3.50 V 1 0 1 1 0 1 5.10 V* 0 0 1 1 1 0 3.55 V 1 0 1 1 1 0 5.15 V* 0 0 1 1 1 1 3.60 V 1 0 1 1 1 1 5.20 V* 0 1 0 0 0 0 3.65 V 1 1 0 0 0 0 5.25 V* 0 1 0 0 0 1 3.70 V 1 1 0 0 0 1 5.30 V* 0 1 0 0 1 0 3.75 V 1 1 0 0 1 0 5.35 V* 0 1 0 0 1 1 3.80 V 1 1 0 0 1 1 5.40 V* 0 1 0 1 0 0 3.85 V 1 1 0 1 0 0 5.45 V* 0 1 0 1 0 1 3.90 V 1 1 0 1 0 1 5.50 V* 0 1 0 1 1 0 3.95 V 1 1 0 1 1 0 5.55 V* 0 1 0 1 1 1 4.00 V 1 1 0 1 1 1 5.60 V* 0 1 1 0 0 0 4.05 V 1 1 1 0 0 0 5.65 V* 0 1 1 0 0 1 4.10 V 1 1 1 0 0 1 5.70 V* 0 1 1 0 1 0 4.15 V 1 1 1 0 1 0 5.75 V* 0 1 1 0 1 1 4.20 V 1 1 1 0 1 1 5.80 V* 0 1 1 1 0 0 4.25 V 1 1 1 1 0 0 5.85 V* 0 1 1 1 0 1 4.30 V 1 1 1 1 0 1 5.90 V* 0 1 1 1 1 0 4.35 V 1 1 1 1 1 0 5.95 V* 0 1 1 1 1 1 4.40 V 1 1 1 1 1 1 6.00 V*/- u8 power_1;
- /** @power_2: Power Control 2 (C1h) */
- /*
* BT [2:0]: Sets the factor used in the step-up circuits.* Select the optimal step-up factor for the operating voltage. To* reduce power consumption, set a smaller factor.** BT[2:0] AVDD VGH VGL* 0 0 0 VCI x 2 VCI x 7 VCI x 4* 0 0 1 VCI x 3* 0 1 0 VCI x 6 VCI x 4* 0 1 1 VCI x 3**/- u8 power_2;
- /** @vcom_1: VCOM Control 1(C5h) */
- /*
* VMH [6:0] : Set the VCOMH voltage** VMH[6:0] VCOMH(V) VMH[6:0] VCOMH(V) VMH[6:0] VCOMH(V) VMH[6:0] VCOMH* 0000000 2.700 0100000 3.500 1000000 4.300 1100000 5.100* 0000001 2.725 0100001 3.525 1000001 4.325 1100001 5.125* 0000010 2.750 0100010 3.550 1000010 4.350 1100010 5.150* 0000011 2.775 0100011 3.575 1000011 4.375 1100011 5.175* 0000100 2.800 0100100 3.600 1000100 4.400 1100100 5.200* 0000101 2.825 0100101 3.625 1000101 4.425 1100101 5.225* 0000110 2.850 0100110 3.650 1000110 4.450 1100110 5.250* 0000111 2.875 0100111 3.675 1000111 4.475 1100111 5.275* 0001000 2.900 0101000 3.700 1001000 4.500 1101000 5.300* 0001001 2.925 0101001 3.725 1001001 4.525 1101001 5.325* 0001010 2.950 0101010 3.750 1001010 4.550 1101010 5.350* 0001011 2.975 0101011 3.775 1001011 4.575 1101011 5.375* 0001100 3.000 0101100 3.800 1001100 4.600 1101100 5.400* 0001101 3.025 0101101 3.825 1001101 4.625 1101101 5.425* 0001110 3.050 0101110 3.850 1001110 4.650 1101110 5.450* 0001111 3.075 0101111 3.875 1001111 4.675 1101111 5.475* 0010000 3.100 0110000 3.900 1010000 4.700 1110000 5.500* 0010001 3.125 0110001 3.925 1010001 4.725 1110001 5.525* 0010010 3.150 0110010 3.950 1010010 4.750 1110010 5.550* 0010011 3.175 0110011 3.975 1010011 4.775 1110011 5.575* 0010100 3.200 0110100 4.000 1010100 4.800 1110100 5.600* 0010101 3.225 0110101 4.025 1010101 4.825 1110101 5.625* 0010110 3.250 0110110 4.050 1010110 4.850 1110110 5.650* 0010111 3.275 0110111 4.075 1010111 4.875 1110111 5.675* 0011000 3.300 0111000 4.100 1011000 4.900 1111000 5.700* 0011001 3.325 0111001 4.125 1011001 4.925 1111001 5.725* 0011010 3.350 0111010 4.150 1011010 4.950 1111010 5.750* 0011011 3.375 0111011 4.175 1011011 4.975 1111011 5.775* 0011100 3.400 0111100 4.200 1011100 5.000 1111100 5.800* 0011101 3.425 0111101 4.225 1011101 5.025 1111101 5.825* 0011110 3.450 0111110 4.250 1011110 5.050 1111110 5.850* 0011111 3.475 0111111 4.275 1011111 5.075 1111111 5.875** VML[6:0] : Set the VCOML voltage** VML[6:0] VCOML(V) VML[6:0] VCOML(V) VML[6:0] VCOML(V) VML[6:0] VCOML* 0000000 -2.500 0100000 -1.700 1000000 -0.900 1100000 -0.100* 0000001 -2.475 0100001 -1.675 1000001 -0.875 1100001 -0.075* 0000010 -2.450 0100010 -1.650 1000010 -0.850 1100010 -0.050* 0000011 -2.425 0100011 -1.625 1000011 -0.825 1100011 -0.025* 0000100 -2.400 0100100 -1.600 1000100 -0.800 1100100 0* 0000101 -2.375 0100101 -1.575 1000101 -0.775 1100101 Reserved* 0000110 -2.350 0100110 -1.550 1000110 -0.750 1100110 Reserved* 0000111 -2.325 0100111 -1.525 1000111 -0.725 1100111 Reserved* 0001000 -2.300 0101000 -1.500 1001000 -0.700 1101000 Reserved* 0001001 -2.275 0101001 -1.475 1001001 -0.675 1101001 Reserved* 0001010 -2.250 0101010 -1.450 1001010 -0.650 1101010 Reserved* 0001011 -2.225 0101011 -1.425 1001011 -0.625 1101011 Reserved* 0001100 -2.200 0101100 -1.400 1001100 -0.600 1101100 Reserved* 0001101 -2.175 0101101 -1.375 1001101 -0.575 1101101 Reserved* 0001110 -2.150 0101110 -1.350 1001110 -0.550 1101110 Reserved* 0001111 -2.125 0101111 -1.325 1001111 -0.525 1101111 Reserved* 0010000 -2.100 0110000 -1.300 1010000 -0.500 1110000 Reserved* 0010001 -2.075 0110001 -1.275 1010001 -0.475 1110001 Reserved* 0010010 -2.050 0110010 -1.250 1010010 -0.450 1110010 Reserved* 0010011 -2.025 0110011 -1.225 1010011 -0.425 1110011 Reserved* 0010100 -2.000 0110100 -1.200 1010100 -0.400 1110100 Reserved* 0010101 -1.975 0110101 -1.175 1010101 -0.375 1110101 Reserved* 0010110 -1.950 0110110 -1.150 1010110 -0.350 1110110 Reserved* 0010111 -1.925 0110111 -1.125 1010111 -0.325 1110111 Reserved* 0011000 -1.900 0111000 -1.100 1011000 -0.300 1111000 Reserved* 0011001 -1.875 0111001 -1.075 1011001 -0.275 1111001 Reserved* 0011010 -1.850 0111010 -1.050 1011010 -0.250 1111010 Reserved* 0011011 -1.825 0111011 -1.025 1011011 -0.225 1111011 Reserved* 0011100 -1.800 0111100 -1.000 1011100 -0.200 1111100 Reserved* 0011101 -1.775 0111101 -0.975 1011101 -0.175 1111101 Reserved* 0011110 -1.750 0111110 -0.950 1011110 -0.150 1111110 Reserved* 0011111 -1.725 0111111 -0.925 1011111 -0.125 1111111 Reserved*/- u8 vcom_1[ILI9341_VCOM_1_LEN];
- /** @vcom_2: VCOM Control 2(C7h) */
- /*
* C7h VMCTRL1 (VCOM Control 1)* D/CX RDX WRX D17-8 D7 D6 D5 D4 D3 D2 D1 D0 HEX* Command 0 1 M XX 1 1 0 0 0 1 1 1 C7h* Parameter 1 1 M XX nVM VMF[6:0] C0** nVM: nVM equals to “0” after power on reset and VCOM offset* equals to program MTP value. When nVM set to “1”, setting* of VMF [6:0] becomes valid and VCOMH/VCOML can be adjusted.** VMF [6:0]: Set the VCOM offset voltage.*/- u8 vcom_2;
- /** @address_mode: Memory Access Control (36h) */
- /*
* 36h MADCTL (Memory Access Control)* D/CX RDX WRX D17-8 D7 D6 D5 D4 D3 D2 D1 D0 HEX* Command 0 1 M XX 0 0 1 1 0 1 1 0 36h* Parameter 1 1 M XX MY MX MV ML BGR MH 0 0 00** This command defines read/write scanning direction of frame memory.* This command makes no change on the other driver status.** Bit Name Description* MY Row Address Order* MX Column Address Order* MV Row / Column Exchange These 3 bits control MCU to memory* write/read direction.* ML Vertical Refresh Order LCD vertical refresh direction control.* BGR RGB-BGR Order Color selector switch control* (0=RGB color filter panel, 1=BGR* color filter panel)* MH Horizontal Refresh ORDER LCD horizontal refreshing* direction control.** Note: When BGR bit is changed, the new setting is active* immediately without update the content in Frame Memory again.**/- u8 address_mode;
- /** @g3amma_en: TODO: need comments for this register */
- u8 g3amma_en;
- /** @rgb_interface: RGB Interface Signal Control (B0h) */
- /*
* B0h IFMODE (Interface Mode Control)* D/CX RDX WRX D17-8 D7 D6 D5 D4 D3 D2 D1 D0 HEX* Command 0 1 M XX 1 0 1 1 0 0 0 0 B0h* Parameter 1 1 M XX ByPass_MODE RCM[1] RCM[0] 0 VSPL HSPL DPL EPL 40** Sets the operation status of the display interface. The setting* becomes effective as soon as the command is received.* EPL: DE polarity (“0”= High enable for RGB interface, “1”= Low* enable for RGB interface)** DPL: DOTCLK polarity set (“0”= data fetched at the rising time,* “1”= data fetched at the falling time)** HSPL: HSYNC polarity (“0”= Low level sync clock, “1”= High* level sync clock)** VSPL: VSYNC polarity (“0”= Low level sync clock, “1”= High* level sync clock)** RCM [1:0]: RGB interface selection (refer to the RGB interface* section).** ByPass_MODE: Select display data path whether Memory or Direct to* Shift register when RGB Interface is used.** ByPass_MODE Display Data Path* 0 Direct to Shift Register (default)* 1 Memory*/- u8 rgb_interface;
- /** @dfc_2: refer to dfc_1 */
- u8 dfc_2[ILI9341_DFC_2_LEN];
- /** @column_addr: Column Address Set (2Ah) */
- /* This command is used to define area of frame memory where MCU can
* access. This command makes no change on the* other driver status. The values of SC [15:0] and EC [15:0] are* referred when RAMWR command comes. Each value* represents one column line in the Frame Memory.*/- u8 column_addr[ILI9341_COLUMN_ADDR_LEN];
- /** @page_addr: Page Address Set (2Bh) */
- /* This command is used to define area of frame memory where MCU can
* access. This command makes no change on the* other driver status. The values of SP [15:0] and EP [15:0] are* referred when RAMWR command comes. Each value* represents one Page line in the Frame Memory.*/- u8 page_addr[ILI9341_PAGE_ADDR_LEN];
- /** @interface: Interface Control (F6h) */
- /*
* F6h IFCTL (16bits Data Format Selection)* D/CX RDX WRX D17-8 D7 D6 D5 D4 D3 D2 D1 D0 HEX* Command 0 1 M XX 1 1 1 1 0 1 1 0 F6h* 1stParameter 1 1 M XX MY MX MV* _EOR _EOR _EOR 0 BGR_EOR 0 0 WE MODE 01* 2ndParameter 1 1 M XX 0 0 EPF[1] EPF[0] 0 0 MDT[1] MDT[0] 00* 3rdParameter 1 1 M XX 0 0 ENDIAN 0 DM[1] DM[0] RM RIM 00**/- u8 interface[ILI9341_INTERFACE_LEN];
- /** @pixel_format: This command sets the pixel format for the RGB image data used by */
- /* the interface. DPI [2:0] is the pixel format select of RGB
* interface and DBI [2:0] is the pixel format of MCU interface. If a* particular interface, either RGB interface or MCU interface, is* not used then the corresponding bits in the parameter are ignored.* The pixel format is shown in the table below.** DPI[2:0] RGB Interface Format DBI[2:0] MCU Interface Format* 0 0 0 Reserved 0 0 0 Reserved* 0 0 1 Reserved 0 0 1 Reserved* 0 1 0 Reserved 0 1 0 Reserved* 0 1 1 Reserved 0 1 1 Reserved* 1 0 0 Reserved 1 0 0 Reserved* 1 0 1 16 bits / pixel 1 0 1 16 bits / pixel* 1 1 0 18 bits / pixel 1 1 0 18 bits / pixel* 1 1 1 Reserved 1 1 1 Reserved**/- u8 pixel_format;
- /** @gamma_curve: This command is used to select the desired Gamma curve for the */
- /* current display. A maximum of 4 fixed gamma curves can
* be selected. The curve is selected by setting the appropriate bit* in the parameter as described in the Table:** GC [7:0] Curve Selected* 01h Gamma curve 1 (G2.2)* 02h ---* 04h ---* 08h ---*/- u8 gamma_curve;
- /** @pgamma: Positive Gamma Correction (E0h) */
- /*
* Set the gray scale voltage to adjust the gamma characteristics of* the TFT panel.*/- u8 pgamma[ILI9341_PGAMMA_LEN];
- /** @ngamma: Negative Gamma Correction (E1h) */
- /*
* Set the gray scale voltage to adjust the gamma characteristics of* the TFT panel.*/- u8 ngamma[ILI9341_NGAMMA_LEN];
+};
+struct ili9341 {
- struct device *dev;
- const struct ili9341_config *conf;
- struct drm_panel panel;
- struct gpio_desc *reset_gpio;
- struct gpio_desc *dc_gpio;
- u32 max_spi_speed;
- struct regulator *vcc;
+};
+/*
- The Stm32f429-disco board has a panel ili9341 connected to ltdc controller
- */
+static const struct ili9341_config ili9341_stm32f429_disco_data = {
- .max_spi_speed = 10000000,
- .mode = {
.clock = 6100,.hdisplay = 240,.hsync_start = 240 + 10,/* hfp 10 */.hsync_end = 240 + 10 + 10,/* hsync 10 */.htotal = 240 + 10 + 10 + 20,/* hbp 20 */.vdisplay = 320,.vsync_start = 320 + 4,/* vfp 4 */.vsync_end = 320 + 4 + 2,/* vsync 2 */.vtotal = 320 + 4 + 2 + 2,/* vbp 2 */.flags = 0,.width_mm = 65,.height_mm = 50,.type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED,- },
- /* TODO: need comments for this register */
- .ca = {0xc3, 0x08, 0x50},
- /* TODO: need comments for this register */
- .power_b = {0x00, 0xc1, 0x30},
- /* TODO: need comments for this register */
- .power_seq = {0x64, 0x03, 0x12, 0x81},
- /* TODO: need comments for this register */
- .dtca = {0x85, 0x00, 0x78},
- /* TODO: need comments for this register */
- .power_a = {0x39, 0x2c, 0x00, 0x34, 0x02},
- /* TODO: need comments for this register */
- .prc = 0x20,
- /* TODO: need comments for this register */
- .dtcb = {0x00, 0x00},
- /* 0x00 fosc, 0x1b 70hz */
- .frc = {0x00, 0x1b},
- /* 0x0a Interval scan, AGND AGND AGND AGND
* 0xa2 Normally white, G1 -> G320, S720 -> S1,* Scan Cycle 5 frames,85ms*/- .dfc_1 = {0x0a, 0xa2},
- /* 0x10 3.65v */
- .power_1 = 0x10,
- /* 0x10 AVDD=vci*2, VGH=vci*7, VGL=-vci*4 */
- .power_2 = 0x10,
- /* 0x45 VCOMH 4.425v, 0x15 VCOML -1.975*/
- .vcom_1 = {0x45, 0x15},
- /* 0x90 offset voltage, VMH-48, VML-48 */
- .vcom_2 = 0x90,
- /* 0xc8 Row Address Order, Column Address Order
* BGR 1*/- .address_mode = 0xc8,
- .g3amma_en = 0x00,
- /* 0xc2
* Display Data Path: Memory* RGB: DE mode* DOTCLK polarity set (data fetched at the falling time)*/- .rgb_interface = ILI9341_RGB_DISP_PATH_MEM |
ILI9341_RGB_DE_MODE |ILI9341_RGB_DPL,- /*
* 0x0a* Gate outputs in non-display area: Interval scan* Determine source/VCOM output in a non-display area in the partial* display mode: AGND AGND AGND AGND** 0xa7* Scan Cycle: 15 frames* fFLM = 60Hz: 255ms* Liquid crystal type: Normally white* Gate Output Scan Direction: G1 -> G320* Source Output Scan Direction: S720 -> S1** 0x27* LCD Driver Line: 320 lines** 0x04* PCDIV: 4*/- .dfc_2 = {0x0a, 0xa7, 0x27, 0x04},
- /* column address: 240 */
- .column_addr = {0x00, 0x00, (ILI9341_COLUMN_ADDR >> 4) & 0xff,
ILI9341_COLUMN_ADDR & 0xff},- /* page address: 320 */
- .page_addr = {0x00, 0x00, (ILI9341_PAGE_ADDR >> 4) & 0xff,
ILI9341_PAGE_ADDR & 0xff},- /* Memory write control: When the transfer number of data exceeds
* (EC-SC+1)*(EP-SP+1), the column and page number will be* reset, and the exceeding data will be written into the following* column and page.* Display Operation Mode: RGB Interface Mode* Interface for RAM Access: RGB interface* 16- bit RGB interface (1 transfer/pixel)*/- .interface = {ILI9341_IF_WE_MODE, 0x00,
ILI9341_IF_DM_RGB | ILI9341_IF_RM_RGB},- /* DPI: 16 bits / pixel */
- .pixel_format = ILI9341_PIXEL_DPI_16_BITS,
- /* Curve Selected: Gamma curve 1 (G2.2) */
- .gamma_curve = ILI9341_GAMMA_CURVE_1,
- .pgamma = {0x0f, 0x29, 0x24, 0x0c, 0x0e,
0x09, 0x4e, 0x78, 0x3c, 0x09,0x13, 0x05, 0x17, 0x11, 0x00},- .ngamma = {0x00, 0x16, 0x1b, 0x04, 0x11,
0x07, 0x31, 0x33, 0x42, 0x05,0x0c, 0x0a, 0x28, 0x2f, 0x0f},+};
+static inline struct ili9341 *panel_to_ili9341(struct drm_panel *panel) +{
- return container_of(panel, struct ili9341, panel);
+}
+static int ili9341_spi_transfer(struct spi_device *spi, u32 speed_hz,
u8 bpw, const void *buf, size_t len)+{
- size_t max_chunk = spi_max_transfer_size(spi);
- struct spi_transfer tr = {
.bits_per_word = bpw,.speed_hz = speed_hz,.len = len,- };
- struct spi_message m;
- size_t chunk;
- int ret;
- spi_message_init_with_transfers(&m, &tr, 1);
- while (len) {
chunk = min(len, max_chunk);tr.tx_buf = buf;tr.len = chunk;buf += chunk;len -= chunk;ret = spi_sync(spi, &m);if (ret) {dev_err(&spi->dev, "spi_sync error: %d\n", ret);return ret;}- }
- return 0;
+}
+static int _ili9341_command(struct ili9341 *ili, u8 cmd, const void *data,
size_t count)+{
- struct spi_device *spi = to_spi_device(ili->dev);
- int ret = 0;
- gpiod_set_value_cansleep(ili->dc_gpio, 0);
- ret = ili9341_spi_transfer(spi, ili->max_spi_speed, 8,
(const void *)&cmd, 1);- if (ret || data == NULL || count == 0) {
return ret;- }
- gpiod_set_value_cansleep(ili->dc_gpio, 1);
- return ili9341_spi_transfer(spi, ili->max_spi_speed, 8,
data, count);+}
+static int ili9341_dpi_init(struct ili9341 *ili) +{
- int ret;
- ret = _ili9341_command(ili, 0xca,
ili->conf->ca,ILI9341_CA_LEN);- if (ret)
return ret;- ret = _ili9341_command(ili, ILI9341_POWERB,
ili->conf->power_b,ILI9341_POWER_B_LEN);- if (ret)
return ret;- ret = _ili9341_command(ili, ILI9341_POWER_SEQ,
ili->conf->power_seq,ILI9341_POWER_SEQ_LEN);- if (ret)
return ret;- ret = _ili9341_command(ili, ILI9341_DTCA,
ili->conf->dtca,ILI9341_DTCA_LEN);- if (ret)
return ret;- ret = _ili9341_command(ili, ILI9341_POWERA,
ili->conf->power_a,ILI9341_POWER_A_LEN);- if (ret)
return ret;- ret = _ili9341_command(ili, ILI9341_PRC,
&ili->conf->prc,1);- if (ret)
return ret;- ret = _ili9341_command(ili, ILI9341_DTCB,
ili->conf->dtcb,ILI9341_DTCB_LEN);- if (ret)
return ret;- ret = _ili9341_command(ili, ILI9341_FRC,
ili->conf->frc,ILI9341_FRC_LEN);- if (ret)
return ret;- ret = _ili9341_command(ili, ILI9341_DFC,
ili->conf->dfc_1,ILI9341_DFC_1_LEN);- if (ret)
return ret;- ret = _ili9341_command(ili, ILI9341_POWER1,
&ili->conf->power_1,1);- if (ret)
return ret;- ret = _ili9341_command(ili, ILI9341_POWER2,
&ili->conf->power_2,1);- if (ret)
return ret;- ret = _ili9341_command(ili, ILI9341_VCOM1,
ili->conf->vcom_1,ILI9341_VCOM_1_LEN);- if (ret)
return ret;- ret = _ili9341_command(ili, ILI9341_VCOM2,
&ili->conf->vcom_2,1);- if (ret)
return ret;- ret = _ili9341_command(ili, MIPI_DCS_SET_ADDRESS_MODE,
&ili->conf->address_mode,1);- if (ret)
return ret;- ret = _ili9341_command(ili, ILI9341_3GAMMA_EN,
&ili->conf->g3amma_en,1);- if (ret)
return ret;- ret = _ili9341_command(ili, ILI9341_RGB_INTERFACE,
&ili->conf->rgb_interface,1);- if (ret)
return ret;- ret = _ili9341_command(ili, ILI9341_DFC,
ili->conf->dfc_2,ILI9341_DFC_2_LEN);- if (ret)
return ret;- ret = _ili9341_command(ili, MIPI_DCS_SET_COLUMN_ADDRESS,
ili->conf->column_addr,ILI9341_COLUMN_ADDR_LEN);- if (ret)
return ret;- ret = _ili9341_command(ili, MIPI_DCS_SET_PAGE_ADDRESS,
ili->conf->page_addr,ILI9341_PAGE_ADDR_LEN);- if (ret)
return ret;- ret = _ili9341_command(ili, ILI9341_INTERFACE,
ili->conf->interface,ILI9341_INTERFACE_LEN);- if (ret)
return ret;- ret = _ili9341_command(ili, MIPI_DCS_SET_PIXEL_FORMAT,
&ili->conf->pixel_format,1);- if (ret)
return ret;- ret = ili9341_command(ili, MIPI_DCS_WRITE_MEMORY_START);
- if (ret)
return ret;- msleep(200);
- ret = _ili9341_command(ili, MIPI_DCS_SET_GAMMA_CURVE,
&ili->conf->gamma_curve,1);- if (ret)
return ret;- ret = _ili9341_command(ili, ILI9341_PGAMMA,
ili->conf->pgamma,ILI9341_PGAMMA_LEN);- if (ret)
return ret;- ret = _ili9341_command(ili, ILI9341_NGAMMA,
ili->conf->ngamma,ILI9341_NGAMMA_LEN);- if (ret)
return ret;- ret = ili9341_command(ili, MIPI_DCS_EXIT_SLEEP_MODE);
- if (ret)
return ret;- msleep(200);
- ret = ili9341_command(ili, MIPI_DCS_SET_DISPLAY_ON);
- if (ret)
return ret;- ret = ili9341_command(ili, MIPI_DCS_WRITE_MEMORY_START);
- if (ret)
return ret;- dev_info(ili->dev, "initialized display rgb interface\n");
- return 0;
+}
+static int ili9341_dpi_power_on(struct ili9341 *ili) +{
- int ret = 0;
- /* Assert RESET */
- gpiod_set_value(ili->reset_gpio, 1);
- /* Enable power */
- if (!IS_ERR(ili->vcc)) {
ret = regulator_enable(ili->vcc);if (ret < 0) {dev_err(ili->dev, "unable to enable vcc\n");return ret;}- }
- msleep(20);
- /* De-assert RESET */
- gpiod_set_value(ili->reset_gpio, 0);
- msleep(10);
- return 0;
+}
+static int ili9341_dpi_power_off(struct ili9341 *ili) +{
- /* Assert RESET */
- gpiod_set_value(ili->reset_gpio, 1);
- /* Disable power */
- if (!IS_ERR(ili->vcc))
return regulator_disable(ili->vcc);- return 0;
+}
+static int ili9341_dpi_disable(struct drm_panel *panel) +{
- struct ili9341 *ili = panel_to_ili9341(panel);
- ili9341_command(ili, MIPI_DCS_SET_DISPLAY_OFF);
- return 0;
+}
+static int ili9341_dpi_unprepare(struct drm_panel *panel) +{
- struct ili9341 *ili = panel_to_ili9341(panel);
- return ili9341_dpi_power_off(ili);
+}
+static int ili9341_dpi_prepare(struct drm_panel *panel) +{
- struct ili9341 *ili = panel_to_ili9341(panel);
- int ret;
- ret = ili9341_dpi_power_on(ili);
- if (ret < 0)
return ret;- ret = ili9341_dpi_init(ili);
- if (ret < 0)
ili9341_dpi_unprepare(panel);- return ret;
+}
+static int ili9341_dpi_enable(struct drm_panel *panel) +{
- struct ili9341 *ili = panel_to_ili9341(panel);
- ili9341_command(ili, MIPI_DCS_SET_DISPLAY_ON);
- return 0;
+}
+static int ili9341_dpi_get_modes(struct drm_panel *panel,
struct drm_connector *connector)+{
- struct ili9341 *ili = panel_to_ili9341(panel);
- struct drm_device *drm = connector->dev;
- struct drm_display_mode *mode;
- struct drm_display_info *info;
- info = &connector->display_info;
- info->width_mm = ili->conf->mode.width_mm;
- info->height_mm = ili->conf->mode.height_mm;
- if (ili->conf->rgb_interface & ILI9341_RGB_DPL)
info->bus_flags |= DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE;- else
info->bus_flags |= DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE;- if (ili->conf->rgb_interface & ILI9341_RGB_EPL)
info->bus_flags |= DRM_BUS_FLAG_DE_LOW;- else
info->bus_flags |= DRM_BUS_FLAG_DE_HIGH;- mode = drm_mode_duplicate(drm, &ili->conf->mode);
- if (!mode) {
DRM_ERROR("bad mode or failed to add mode\n");return -EINVAL;- }
- drm_mode_set_name(mode);
- /* Set up the polarity */
- if (ili->conf->rgb_interface & ILI9341_RGB_HSPL)
mode->flags |= DRM_MODE_FLAG_PHSYNC;- else
mode->flags |= DRM_MODE_FLAG_NHSYNC;- if (ili->conf->rgb_interface & ILI9341_RGB_VSPL)
mode->flags |= DRM_MODE_FLAG_PVSYNC;- else
mode->flags |= DRM_MODE_FLAG_NVSYNC;- drm_mode_probed_add(connector, mode);
- return 1; /* Number of modes */
+}
+static const struct drm_panel_funcs ili9341_dpi_funcs = {
- .disable = ili9341_dpi_disable,
- .unprepare = ili9341_dpi_unprepare,
- .prepare = ili9341_dpi_prepare,
- .enable = ili9341_dpi_enable,
- .get_modes = ili9341_dpi_get_modes,
+};
+static int ili9341_dpi_probe(struct spi_device *spi) +{
- int ret;
- struct device *dev = &spi->dev;
- struct ili9341 *ili;
- ili = devm_kzalloc(dev, sizeof(struct ili9341), GFP_KERNEL);
- if (!ili)
return -ENOMEM;- spi_set_drvdata(spi, ili);
- ili->dev = dev;
- /*
* Every new incarnation of this display must have a unique* data entry for the system in this driver.*/- ili->conf = of_device_get_match_data(dev);
- if (!ili->conf) {
dev_err(dev, "missing device configuration\n");return -ENODEV;- }
- ili->vcc = devm_regulator_get_optional(dev, "vcc");
- if (IS_ERR(ili->vcc))
dev_err(dev, "get optional vcc failed\n");- ili->reset_gpio = devm_gpiod_get_optional(dev, "reset",
GPIOD_OUT_HIGH);- if (IS_ERR(ili->reset_gpio)) {
dev_err(dev, "failed to get RESET GPIO\n");return PTR_ERR(ili->reset_gpio);- }
- ili->dc_gpio = devm_gpiod_get(dev, "dc", GPIOD_OUT_LOW);
- if (IS_ERR(ili->dc_gpio)) {
dev_err(dev, "failed to get DC GPIO\n");return PTR_ERR(ili->dc_gpio);- }
- spi->bits_per_word = 8;
- ret = spi_setup(spi);
- if (ret < 0) {
dev_err(dev, "spi setup failed.\n");return ret;- }
- ili->max_spi_speed = ili->conf->max_spi_speed;
- drm_panel_init(&ili->panel, dev, &ili9341_dpi_funcs,
DRM_MODE_CONNECTOR_DPI);- drm_panel_add(&ili->panel);
- return 0;
+}
+static void ili9341_dbi_enable(struct drm_simple_display_pipe *pipe,
struct drm_crtc_state *crtc_state,struct drm_plane_state *plane_state)+{
- struct mipi_dbi_dev *dbidev = drm_to_mipi_dbi_dev(pipe->crtc.dev);
- struct mipi_dbi *dbi = &dbidev->dbi;
- u8 addr_mode;
- int ret, idx;
- if (!drm_dev_enter(pipe->crtc.dev, &idx))
return;- DRM_DEBUG_KMS("\n");
- ret = mipi_dbi_poweron_conditional_reset(dbidev);
- if (ret < 0)
goto out_exit;- if (ret == 1)
goto out_enable;- mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_OFF);
- mipi_dbi_command(dbi, ILI9341_POWERB, 0x00, 0xc1, 0x30);
- mipi_dbi_command(dbi, ILI9341_POWER_SEQ, 0x64, 0x03, 0x12, 0x81);
- mipi_dbi_command(dbi, ILI9341_DTCA, 0x85, 0x00, 0x78);
- mipi_dbi_command(dbi, ILI9341_POWERA, 0x39, 0x2c, 0x00, 0x34, 0x02);
- mipi_dbi_command(dbi, ILI9341_PRC, ILI9341_DBI_PRC_NORMAL);
- mipi_dbi_command(dbi, ILI9341_DTCB, 0x00, 0x00);
- /* Power Control */
- mipi_dbi_command(dbi, ILI9341_POWER1, ILI9341_DBI_VCOMH_4P6V);
- mipi_dbi_command(dbi, ILI9341_POWER2, ILI9341_DBI_PWR_2_DEFAULT);
- /* VCOM */
- mipi_dbi_command(dbi, ILI9341_VCOM1, ILI9341_DBI_VCOM_1_VMH_4P25V,
ILI9341_DBI_VCOM_1_VML_1P5V);- mipi_dbi_command(dbi, ILI9341_VCOM2, ILI9341_DBI_VCOM_2_DEC_58);
- /* Memory Access Control */
- mipi_dbi_command(dbi, MIPI_DCS_SET_PIXEL_FORMAT,
MIPI_DCS_PIXEL_FMT_16BIT);- /* Frame Rate */
- mipi_dbi_command(dbi, ILI9341_FRC, ILI9341_DBI_FRC_DIVA & 0x03,
ILI9341_DBI_FRC_RTNA & 0x1f);- /* Gamma */
- mipi_dbi_command(dbi, ILI9341_3GAMMA_EN, 0x00);
- mipi_dbi_command(dbi, MIPI_DCS_SET_GAMMA_CURVE, ILI9341_GAMMA_CURVE_1);
- mipi_dbi_command(dbi, ILI9341_PGAMMA,
0x0f, 0x31, 0x2b, 0x0c, 0x0e, 0x08, 0x4e, 0xf1,0x37, 0x07, 0x10, 0x03, 0x0e, 0x09, 0x00);- mipi_dbi_command(dbi, ILI9341_NGAMMA,
0x00, 0x0e, 0x14, 0x03, 0x11, 0x07, 0x31, 0xc1,0x48, 0x08, 0x0f, 0x0c, 0x31, 0x36, 0x0f);- /* DDRAM */
- mipi_dbi_command(dbi, ILI9341_ETMOD, ILI9341_DBI_EMS_GAS |
ILI9341_DBI_EMS_DTS |ILI9341_DBI_EMS_GON);- /* Display */
- mipi_dbi_command(dbi, ILI9341_DFC, 0x08, 0x82, 0x27, 0x00);
- mipi_dbi_command(dbi, MIPI_DCS_EXIT_SLEEP_MODE);
- msleep(100);
- mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_ON);
- msleep(100);
+out_enable:
- switch (dbidev->rotation) {
- default:
addr_mode = ILI9341_MADCTL_MX;break;- case 90:
addr_mode = ILI9341_MADCTL_MV;break;- case 180:
addr_mode = ILI9341_MADCTL_MY;break;- case 270:
addr_mode = ILI9341_MADCTL_MV | ILI9341_MADCTL_MY |ILI9341_MADCTL_MX;break;- }
- addr_mode |= ILI9341_MADCTL_BGR;
- mipi_dbi_command(dbi, MIPI_DCS_SET_ADDRESS_MODE, addr_mode);
- mipi_dbi_enable_flush(dbidev, crtc_state, plane_state);
- DRM_DEBUG_KMS("initialized display serial interface\n");
+out_exit:
- drm_dev_exit(idx);
+}
+static const struct drm_simple_display_pipe_funcs ili9341_dbi_funcs = {
- .enable = ili9341_dbi_enable,
- .disable = mipi_dbi_pipe_disable,
- .update = mipi_dbi_pipe_update,
- .prepare_fb = drm_gem_simple_display_pipe_prepare_fb,
+};
+static const struct drm_display_mode ili9341_dbi_mode = {
- DRM_SIMPLE_MODE(240, 320, 37, 49),
+};
+DEFINE_DRM_GEM_CMA_FOPS(ili9341_dbi_fops);
+static struct drm_driver ili9341_dbi_driver = {
- .driver_features = DRIVER_GEM | DRIVER_MODESET | DRIVER_ATOMIC,
- .fops = &ili9341_dbi_fops,
- DRM_GEM_CMA_DRIVER_OPS_VMAP,
- .debugfs_init = mipi_dbi_debugfs_init,
- .name = "ili9341",
- .desc = "Ilitek ILI9341",
- .date = "20180514",
- .major = 1,
- .minor = 0,
+}; +static int ili9341_dbi_probe(struct spi_device *spi) +{
- struct mipi_dbi_dev *dbidev;
- struct drm_device *drm;
- struct mipi_dbi *dbi;
- struct gpio_desc *dc;
- struct device *dev = &spi->dev;
- u32 rotation = 0;
- int ret;
- dbidev = devm_drm_dev_alloc(dev, &ili9341_dbi_driver,
struct mipi_dbi_dev, drm);- if (IS_ERR(dbidev))
return PTR_ERR(dbidev);- dbi = &dbidev->dbi;
- drm = &dbidev->drm;
- drm_mode_config_init(drm);
- dbi->reset = devm_gpiod_get_optional(dev, "reset",
GPIOD_OUT_HIGH);- if (IS_ERR(dbi->reset)) {
DRM_DEV_ERROR(dev, "Failed to get gpio 'reset'\n");return PTR_ERR(dbi->reset);- }
- dc = devm_gpiod_get_optional(dev, "dc", GPIOD_OUT_LOW);
- if (IS_ERR(dc)) {
DRM_DEV_ERROR(dev, "Failed to get gpio 'dc'\n");return PTR_ERR(dc);- }
- dbidev->regulator = devm_regulator_get_optional(dev, "vcc");
- if (IS_ERR(dbidev->regulator))
dev_err(dev, "get optional vcc failed\n");- dbidev->backlight = devm_of_find_backlight(dev);
- if (IS_ERR(dbidev->backlight))
return PTR_ERR(dbidev->backlight);- device_property_read_u32(dev, "rotation", &rotation);
- ret = mipi_dbi_spi_init(spi, dbi, dc);
- if (ret)
return ret;- ret = mipi_dbi_dev_init(dbidev, &ili9341_dbi_funcs,
&ili9341_dbi_mode, rotation);- if (ret)
return ret;- drm_mode_config_reset(drm);
- ret = drm_dev_register(drm, 0);
- if (ret)
return ret;- spi_set_drvdata(spi, drm);
- drm_fbdev_generic_setup(drm, 0);
- return 0;
+} +static int ili9341_probe(struct spi_device *spi) +{
- const struct spi_device_id *id = spi_get_device_id(spi);
- if (!strcmp(id->name, "sf-tc240t-9370-t"))
return ili9341_dpi_probe(spi);- else if (!strcmp(id->name, "yx240qv29"))
return ili9341_dbi_probe(spi);- return -1;
+}
+static int ili9341_remove(struct spi_device *spi) +{
- const struct spi_device_id *id = spi_get_device_id(spi);
- struct ili9341 *ili = spi_get_drvdata(spi);
- struct drm_device *drm = spi_get_drvdata(spi);
- if (!strcmp(id->name, "sf-tc240t-9370-t")) {
ili9341_dpi_power_off(ili);drm_panel_remove(&ili->panel);- } else if (!strcmp(id->name, "yx240qv29")) {
drm_dev_unplug(drm);drm_atomic_helper_shutdown(drm);- }
- return 0;
+}
+static void ili9341_shutdown(struct spi_device *spi) +{
- const struct spi_device_id *id = spi_get_device_id(spi);
- if (!strcmp(id->name, "yx240qv29"))
drm_atomic_helper_shutdown(spi_get_drvdata(spi));+}
+static const struct of_device_id ili9341_of_match[] = {
- {
.compatible = "st,sf-tc240t-9370-t",.data = &ili9341_stm32f429_disco_data,- },
- {
/* porting from tiny/ili9341.c* for original mipi dbi compitable*/.compatible = "adafruit,yx240qv29",.data = NULL,- },
+}; +MODULE_DEVICE_TABLE(of, ili9341_of_match);
+static const struct spi_device_id ili9341_id[] = {
- { "yx240qv29", 0 },
- { "sf-tc240t-9370-t", 0 },
- { }
+}; +MODULE_DEVICE_TABLE(spi, ili9341_id);
+static struct spi_driver ili9341_driver = {
- .probe = ili9341_probe,
- .remove = ili9341_remove,
- .shutdown = ili9341_shutdown,
- .id_table = ili9341_id,
- .driver = {
.name = "panel-ilitek-ili9341",.of_match_table = ili9341_of_match,- },
+}; +module_spi_driver(ili9341_driver);
+MODULE_AUTHOR("Dillon Min dillon.minfei@gmail.com"); +MODULE_DESCRIPTION("ILI9341 LCD panel driver"); +MODULE_LICENSE("GPL v2");