Re: [PATCH] dt-bindings: display: mcde: Convert to YAML schema

On Wed, Nov 04, 2020 at 02:37:09PM +0100, Linus Walleij wrote:

This moves the MCDE bindings over to using the YAML schema to describe the ST-Ericsson MCDE display controller, making use of the generic DSI controller schema.

We also add the "port" node, we will use this when adding LCD panels using the direct parallel interface DPI instead of DSI.

Cc: devicetree@vger.kernel.org Signed-off-by: Linus Walleij linus.walleij@linaro.org

---

.../devicetree/bindings/display/ste,mcde.txt | 104 ----------- .../devicetree/bindings/display/ste,mcde.yaml | 167 ++++++++++++++++++ 2 files changed, 167 insertions(+), 104 deletions(-) delete mode 100644 Documentation/devicetree/bindings/display/ste,mcde.txt create mode 100644 Documentation/devicetree/bindings/display/ste,mcde.yaml

diff --git a/Documentation/devicetree/bindings/display/ste,mcde.txt b/Documentation/devicetree/bindings/display/ste,mcde.txt deleted file mode 100644 index 4c33c692bd5f..000000000000 --- a/Documentation/devicetree/bindings/display/ste,mcde.txt +++ /dev/null @@ -1,104 +0,0 @@ -ST-Ericsson Multi Channel Display Engine MCDE

-The ST-Ericsson MCDE is a display controller with support for compositing -and displaying several channels memory resident graphics data on DSI or -LCD displays or bridges. It is used in the ST-Ericsson U8500 platform.

-Required properties:

-- compatible: must be:

• "ste,mcde"

-- reg: register base for the main MCDE control registers, should be

• 0x1000 in size

-- interrupts: the interrupt line for the MCDE -- epod-supply: a phandle to the EPOD regulator -- vana-supply: a phandle to the analog voltage regulator -- clocks: an array of the MCDE clocks in this strict order:

• MCDECLK (main MCDE clock), LCDCLK (LCD clock), PLLDSI
• (HDMI clock), DSI0ESCLK (DSI0 energy save clock),
• DSI1ESCLK (DSI1 energy save clock), DSI2ESCLK (DSI2 energy
• save clock)

-- clock-names: must be the following array:

• "mcde", "lcd", "hdmi"
• to match the required clock inputs above.

-- #address-cells: should be <1> (for the DSI hosts that will be children) -- #size-cells: should be <1> (for the DSI hosts that will be children) -- ranges: this should always be stated

-Required subnodes:

-The devicetree must specify subnodes for the DSI host adapters. -These must have the following characteristics:

-- compatible: must be:

• "ste,mcde-dsi"

-- reg: must specify the register range for the DSI host -- vana-supply: phandle to the VANA voltage regulator -- clocks: phandles to the high speed and low power (energy save) clocks

• the high speed clock is not present on the third (dsi2) block, so it
• should only have the "lp" clock

-- clock-names: "hs" for the high speed clock and "lp" for the low power

• (energy save) clock

-- #address-cells: should be <1> -- #size-cells: should be <0>

-Display panels and bridges will appear as children on the DSI hosts, and -the displays are connected to the DSI hosts using the common binding -for video transmitter interfaces; see -Documentation/devicetree/bindings/media/video-interfaces.txt

-If a DSI host is unused (not connected) it will have no children defined.

-Example:

-mcde@a0350000 {

• compatible = "ste,mcde";
• reg = <0xa0350000 0x1000>;
• interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
• epod-supply = <&db8500_b2r2_mcde_reg>;
• vana-supply = <&ab8500_ldo_ana_reg>;
• clocks = <&prcmu_clk PRCMU_MCDECLK>, /* Main MCDE clock */

•  <&prcmu_clk PRCMU_LCDCLK>, /* LCD clock */
  

•  <&prcmu_clk PRCMU_PLLDSI>; /* HDMI clock */
  

• clock-names = "mcde", "lcd", "hdmi";
• #address-cells = <1>;
• #size-cells = <1>;
• ranges;
• dsi0: dsi@a0351000 {

• compatible = "ste,mcde-dsi";
  

• reg = <0xa0351000 0x1000>;
  

• vana-supply = <&ab8500_ldo_ana_reg>;
  

• clocks = <&prcmu_clk PRCMU_DSI0CLK>, <&prcmu_clk PRCMU_DSI0ESCCLK>;
  

• clock-names = "hs", "lp";
  

• #address-cells = <1>;
  

• #size-cells = <0>;
  

• panel {
  

• 	compatible = "samsung,s6d16d0";
  

• 	reg = <0>;
  

• 	vdd1-supply = <&ab8500_ldo_aux1_reg>;
  

• 	reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
  

• };
  

• };
• dsi1: dsi@a0352000 {

• compatible = "ste,mcde-dsi";
  

• reg = <0xa0352000 0x1000>;
  

• vana-supply = <&ab8500_ldo_ana_reg>;
  

• clocks = <&prcmu_clk PRCMU_DSI1CLK>, <&prcmu_clk PRCMU_DSI1ESCCLK>;
  

• clock-names = "hs", "lp";
  

• #address-cells = <1>;
  

• #size-cells = <0>;
  

• };
• dsi2: dsi@a0353000 {

• compatible = "ste,mcde-dsi";
  

• reg = <0xa0353000 0x1000>;
  

• vana-supply = <&ab8500_ldo_ana_reg>;
  

• /* This DSI port only has the Low Power / Energy Save clock */
  

• clocks = <&prcmu_clk PRCMU_DSI2ESCCLK>;
  

• clock-names = "lp";
  

• #address-cells = <1>;
  

• #size-cells = <0>;
  

• };

-}; diff --git a/Documentation/devicetree/bindings/display/ste,mcde.yaml b/Documentation/devicetree/bindings/display/ste,mcde.yaml new file mode 100644 index 000000000000..a00333acd9a1 --- /dev/null +++ b/Documentation/devicetree/bindings/display/ste,mcde.yaml @@ -0,0 +1,167 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/ste,mcde.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml#

+title: ST-Ericsson Multi Channel Display Engine MCDE

+maintainers:

• • Linus Walleij linus.walleij@linaro.org

+properties:

• compatible:
• const: ste,mcde
• reg:
• maxItems: 1
• interrupts:
• maxItems: 1
• description: the interrupt line for the MCDE

Kind of generic description. Can drop.

• clocks:
• maxItems: 3

Can drop this. Implied with 'items'.

• description: an array of the MCDE clocks
• items:

•  - description: MCDECLK (main MCDE clock)
  

•  - description: LCDCLK (LCD clock)
  

•  - description: PLLDSI (HDMI clock)
  

• clock-names:
• maxItems: 3

ditto

• items:

•  - const: mcde
  

•  - const: lcd
  

•  - const: hdmi
  

• epod-supply:
• description: a phandle to the EPOD regulator
• vana-supply:
• description: a phandle to the analog voltage regulator
• port:
• type: object
• description:

•  A DPI port node with endpoint definitions as defined in
  

•  Documentation/devicetree/bindings/media/video-interfaces.txt
  

• "#address-cells":
• const: 1
• "#size-cells":
• const: 1
• ranges: true

+patternProperties:

• "^dsi@[0-9a-f]+$":
• description: subnodes for the three DSI host adapters
• type: object
• allOf:

•  - $ref: dsi-controller.yaml#
  

• properties:

•  compatible:
  

•    const: ste,mcde-dsi
  

•  reg:
  

•    maxItems: 1
  

•  vana-supply:
  

•    description: a phandle to the analog voltage regulator
  

•  clocks:
  

•    description: phandles to the high speed and low power (energy save) clocks
  

•      the high speed clock is not present on the third (dsi2) block, so it
  

•      should only have the "lp" clock
  

•    minItems: 1
  

•    maxItems: 2
  

•  clock-names:
  

•    oneOf:
  

•      - items:
  

•          - const: hs
  

•          - const: lp
  

•      - items:
  

•          - const: lp
  

• required:

•  - compatible
  

•  - reg
  

•  - vana-supply
  

•  - clocks
  

•  - clock-names
  

unevaluatedProperties: false

+required:

• • compatible
• • reg
• • interrupts
• • clocks
• • clock-names
• • epod-supply
• • vana-supply

+unevaluatedProperties: false

The meta-schema has gotten stricter recently, so this has to be 'additionalProperties' since there's no other schema referenced. Moving target. :)

Rob