From: Maxime Ripard maxime.ripard@free-electrons.com
The Allwinner SoCs usually come with a DSI encoder. Add a binding for it.
Signed-off-by: Maxime Ripard maxime.ripard@free-electrons.com --- Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt | 84 +++++++- 1 file changed, 84 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt
diff --git a/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt b/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt new file mode 100644 index 000000000000..cbcc673b9bcc --- /dev/null +++ b/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt @@ -0,0 +1,84 @@ +Allwinner A31 DSI Encoder +========================= + +The DSI pipeline consists of two separate blocks: the DSI controller +itself, and its associated D-PHY. + +DSI Encoder +----------- + +The DSI Encoder generates the DSI signal from the TCON's. + +Required properties: + - compatible: value must be one of: + * allwinner,sun6i-a31-mipi-dsi + - reg: base address and size of memory-mapped region + - interrupts: interrupt associated to this IP + - clocks: phandles to the clocks feeding the DSI encoder + * bus: the DSI interface clock + * mod: the DSI module clock + - clock-names: the clock names mentioned above + - phys: phandle to the D-PHY + - phy-names: must be "dphy" + - resets: phandle to the reset controller driving the encoder + + - ports: A ports node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The + port should be the input endpoint, usually coming from the + associated TCON. + +Any MIPI-DSI device attached to this should be described according to +the bindings defined in ../mipi-dsi-bus.txt + +D-PHY +----- + +Required properties: + - compatible: value must be one of: + * allwinner,sun6i-a31-mipi-dphy + - reg: base address and size of memory-mapped region + - clocks: phandles to the clocks feeding the DSI encoder + * bus: the DSI interface clock + * mod: the DSI module clock + - clock-names: the clock names mentioned above + - resets: phandle to the reset controller driving the encoder + +Example: + +dsi0: dsi@1ca0000 { + compatible = "allwinner,sun6i-a31-mipi-dsi"; + reg = <0x01ca0000 0x1000>; + interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_MIPI_DSI>, + <&ccu CLK_DSI_SCLK>; + clock-names = "bus", "mod"; + resets = <&ccu RST_BUS_MIPI_DSI>; + phys = <&dphy0>; + phy-names = "dphy"; + #address-cells = <1>; + #size-cells = <0>; + + panel@0 { + compatible = "huarui,lhr050h41"; + reg = <0>; + power-gpios = <&pio 1 7 GPIO_ACTIVE_HIGH>; /* PB07 */ + reset-gpios = <&r_pio 0 5 GPIO_ACTIVE_LOW>; /* PL05 */ + backlight = <&pwm_bl>; + }; + + port { + dsi0_in_tcon0: endpoint { + remote-endpoint = <&tcon0_out_dsi0>; + }; + }; +}; + +dphy0: d-phy@1ca1000 { + compatible = "allwinner,sun6i-a31-mipi-dphy"; + reg = <0x01ca1000 0x1000>; + clocks = <&ccu CLK_BUS_MIPI_DSI>, + <&ccu CLK_DSI_DPHY>; + clock-names = "bus", "mod"; + resets = <&ccu RST_BUS_MIPI_DSI>; + #phy-cells = <0>; +};