Xingbangda XBD599 is a 5.99" 720x1440 MIPI-DSI LCD panel used in PinePhone. Add support for it.
Signed-off-by: Icenowy Zheng icenowy@aosc.io Signed-off-by: Ondrej Jirman megous@megous.com Reviewed-by: Linus Walleij linus.walleij@linaro.org --- drivers/gpu/drm/panel/panel-sitronix-st7703.c | 200 +++++++++++++++++- 1 file changed, 198 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/panel/panel-sitronix-st7703.c b/drivers/gpu/drm/panel/panel-sitronix-st7703.c index cdbf7dfb4dd4..5cd5503f894f 100644 --- a/drivers/gpu/drm/panel/panel-sitronix-st7703.c +++ b/drivers/gpu/drm/panel/panel-sitronix-st7703.c @@ -39,10 +39,11 @@ #define ST7703_CMD_SETEXTC 0xB9 #define ST7703_CMD_SETMIPI 0xBA #define ST7703_CMD_SETVDC 0xBC -#define ST7703_CMD_UNKNOWN0 0xBF +#define ST7703_CMD_UNKNOWN_BF 0xBF #define ST7703_CMD_SETSCR 0xC0 #define ST7703_CMD_SETPOWER 0xC1 #define ST7703_CMD_SETPANEL 0xCC +#define ST7703_CMD_UNKNOWN_C6 0xC6 #define ST7703_CMD_SETGAMMA 0xE0 #define ST7703_CMD_SETEQ 0xE3 #define ST7703_CMD_SETGIP1 0xE9 @@ -109,7 +110,7 @@ static int jh057n_init_sequence(struct st7703 *ctx) msleep(20);
dsi_generic_write_seq(dsi, ST7703_CMD_SETVCOM, 0x3F, 0x3F); - dsi_generic_write_seq(dsi, ST7703_CMD_UNKNOWN0, 0x02, 0x11, 0x00); + dsi_generic_write_seq(dsi, ST7703_CMD_UNKNOWN_BF, 0x02, 0x11, 0x00); dsi_generic_write_seq(dsi, ST7703_CMD_SETGIP1, 0x82, 0x10, 0x06, 0x05, 0x9E, 0x0A, 0xA5, 0x12, 0x31, 0x23, 0x37, 0x83, 0x04, 0xBC, 0x27, 0x38, @@ -163,6 +164,200 @@ struct st7703_panel_desc jh057n00900_panel_desc = { .init_sequence = jh057n_init_sequence, };
+#define dsi_dcs_write_seq(dsi, cmd, seq...) do { \ + static const u8 d[] = { seq }; \ + int ret; \ + ret = mipi_dsi_dcs_write(dsi, cmd, d, ARRAY_SIZE(d)); \ + if (ret < 0) \ + return ret; \ + } while (0) + + +static int xbd599_init_sequence(struct st7703 *ctx) +{ + struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev); + + /* + * Init sequence was supplied by the panel vendor. + */ + + /* Magic sequence to unlock user commands below. */ + dsi_dcs_write_seq(dsi, ST7703_CMD_SETEXTC, 0xF1, 0x12, 0x83); + + dsi_dcs_write_seq(dsi, ST7703_CMD_SETMIPI, + 0x33, /* VC_main = 0, Lane_Number = 3 (4 lanes) */ + 0x81, /* DSI_LDO_SEL = 1.7V, RTERM = 90 Ohm */ + 0x05, /* IHSRX = x6 (Low High Speed driving ability) */ + 0xF9, /* TX_CLK_SEL = fDSICLK/16 */ + 0x0E, /* HFP_OSC (min. HFP number in DSI mode) */ + 0x0E, /* HBP_OSC (min. HBP number in DSI mode) */ + /* The rest is undocumented in ST7703 datasheet */ + 0x20, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + 0x44, 0x25, 0x00, 0x91, 0x0a, 0x00, 0x00, 0x02, + 0x4F, 0x11, 0x00, 0x00, 0x37); + + dsi_dcs_write_seq(dsi, ST7703_CMD_SETPOWER_EXT, + 0x25, /* PCCS = 2, ECP_DC_DIV = 1/4 HSYNC */ + 0x22, /* DT = 15ms XDK_ECP = x2 */ + 0x20, /* PFM_DC_DIV = /1 */ + 0x03 /* ECP_SYNC_EN = 1, VGX_SYNC_EN = 1 */); + + /* RGB I/F porch timing */ + dsi_dcs_write_seq(dsi, ST7703_CMD_SETRGBIF, + 0x10, /* VBP_RGB_GEN */ + 0x10, /* VFP_RGB_GEN */ + 0x05, /* DE_BP_RGB_GEN */ + 0x05, /* DE_FP_RGB_GEN */ + /* The rest is undocumented in ST7703 datasheet */ + 0x03, 0xFF, + 0x00, 0x00, + 0x00, 0x00); + + /* Source driving settings. */ + dsi_dcs_write_seq(dsi, ST7703_CMD_SETSCR, + 0x73, /* N_POPON */ + 0x73, /* N_NOPON */ + 0x50, /* I_POPON */ + 0x50, /* I_NOPON */ + 0x00, /* SCR[31,24] */ + 0xC0, /* SCR[23,16] */ + 0x08, /* SCR[15,8] */ + 0x70, /* SCR[7,0] */ + 0x00 /* Undocumented */); + + /* NVDDD_SEL = -1.8V, VDDD_SEL = out of range (possibly 1.9V?) */ + dsi_dcs_write_seq(dsi, ST7703_CMD_SETVDC, 0x4E); + + /* + * SS_PANEL = 1 (reverse scan), GS_PANEL = 0 (normal scan) + * REV_PANEL = 1 (normally black panel), BGR_PANEL = 1 (BGR) + */ + dsi_dcs_write_seq(dsi, ST7703_CMD_SETPANEL, 0x0B); + + /* Zig-Zag Type C column inversion. */ + dsi_dcs_write_seq(dsi, ST7703_CMD_SETCYC, 0x80); + + /* Set display resolution. */ + dsi_dcs_write_seq(dsi, ST7703_CMD_SETDISP, + 0xF0, /* NL = 240 */ + 0x12, /* RES_V_LSB = 0, BLK_CON = VSSD, + * RESO_SEL = 720RGB + */ + 0xF0 /* WHITE_GND_EN = 1 (GND), + * WHITE_FRAME_SEL = 7 frames, + * ISC = 0 frames + */); + + dsi_dcs_write_seq(dsi, ST7703_CMD_SETEQ, + 0x00, /* PNOEQ */ + 0x00, /* NNOEQ */ + 0x0B, /* PEQGND */ + 0x0B, /* NEQGND */ + 0x10, /* PEQVCI */ + 0x10, /* NEQVCI */ + 0x00, /* PEQVCI1 */ + 0x00, /* NEQVCI1 */ + 0x00, /* reserved */ + 0x00, /* reserved */ + 0xFF, /* reserved */ + 0x00, /* reserved */ + 0xC0, /* ESD_DET_DATA_WHITE = 1, ESD_WHITE_EN = 1 */ + 0x10 /* SLPIN_OPTION = 1 (no need vsync after sleep-in) + * VEDIO_NO_CHECK_EN = 0 + * ESD_WHITE_GND_EN = 0 + * ESD_DET_TIME_SEL = 0 frames + */); + + /* Undocumented command. */ + dsi_dcs_write_seq(dsi, ST7703_CMD_UNKNOWN_C6, 0x01, 0x00, 0xFF, 0xFF, 0x00); + + dsi_dcs_write_seq(dsi, ST7703_CMD_SETPOWER, + 0x74, /* VBTHS, VBTLS: VGH = 17V, VBL = -11V */ + 0x00, /* FBOFF_VGH = 0, FBOFF_VGL = 0 */ + 0x32, /* VRP */ + 0x32, /* VRN */ + 0x77, /* reserved */ + 0xF1, /* APS = 1 (small), + * VGL_DET_EN = 1, VGH_DET_EN = 1, + * VGL_TURBO = 1, VGH_TURBO = 1 + */ + 0xFF, /* VGH1_L_DIV, VGL1_L_DIV (1.5MHz) */ + 0xFF, /* VGH1_R_DIV, VGL1_R_DIV (1.5MHz) */ + 0xCC, /* VGH2_L_DIV, VGL2_L_DIV (2.6MHz) */ + 0xCC, /* VGH2_R_DIV, VGL2_R_DIV (2.6MHz) */ + 0x77, /* VGH3_L_DIV, VGL3_L_DIV (4.5MHz) */ + 0x77 /* VGH3_R_DIV, VGL3_R_DIV (4.5MHz) */); + + /* Reference voltage. */ + dsi_dcs_write_seq(dsi, ST7703_CMD_SETBGP, + 0x07, /* VREF_SEL = 4.2V */ + 0x07 /* NVREF_SEL = 4.2V */); + msleep(20); + + dsi_dcs_write_seq(dsi, ST7703_CMD_SETVCOM, + 0x2C, /* VCOMDC_F = -0.67V */ + 0x2C /* VCOMDC_B = -0.67V */); + + /* Undocumented command. */ + dsi_dcs_write_seq(dsi, ST7703_CMD_UNKNOWN_BF, 0x02, 0x11, 0x00); + + /* This command is to set forward GIP timing. */ + dsi_dcs_write_seq(dsi, ST7703_CMD_SETGIP1, + 0x82, 0x10, 0x06, 0x05, 0xA2, 0x0A, 0xA5, 0x12, + 0x31, 0x23, 0x37, 0x83, 0x04, 0xBC, 0x27, 0x38, + 0x0C, 0x00, 0x03, 0x00, 0x00, 0x00, 0x0C, 0x00, + 0x03, 0x00, 0x00, 0x00, 0x75, 0x75, 0x31, 0x88, + 0x88, 0x88, 0x88, 0x88, 0x88, 0x13, 0x88, 0x64, + 0x64, 0x20, 0x88, 0x88, 0x88, 0x88, 0x88, 0x88, + 0x02, 0x88, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00); + + /* This command is to set backward GIP timing. */ + dsi_dcs_write_seq(dsi, ST7703_CMD_SETGIP2, + 0x02, 0x21, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + 0x00, 0x00, 0x00, 0x00, 0x02, 0x46, 0x02, 0x88, + 0x88, 0x88, 0x88, 0x88, 0x88, 0x64, 0x88, 0x13, + 0x57, 0x13, 0x88, 0x88, 0x88, 0x88, 0x88, 0x88, + 0x75, 0x88, 0x23, 0x14, 0x00, 0x00, 0x02, 0x00, + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x03, 0x0A, + 0xA5, 0x00, 0x00, 0x00, 0x00); + + /* Adjust the gamma characteristics of the panel. */ + dsi_dcs_write_seq(dsi, ST7703_CMD_SETGAMMA, + 0x00, 0x09, 0x0D, 0x23, 0x27, 0x3C, 0x41, 0x35, + 0x07, 0x0D, 0x0E, 0x12, 0x13, 0x10, 0x12, 0x12, + 0x18, 0x00, 0x09, 0x0D, 0x23, 0x27, 0x3C, 0x41, + 0x35, 0x07, 0x0D, 0x0E, 0x12, 0x13, 0x10, 0x12, + 0x12, 0x18); + + return 0; +} + +static const struct drm_display_mode xbd599_mode = { + .hdisplay = 720, + .hsync_start = 720 + 40, + .hsync_end = 720 + 40 + 40, + .htotal = 720 + 40 + 40 + 40, + .vdisplay = 1440, + .vsync_start = 1440 + 18, + .vsync_end = 1440 + 18 + 10, + .vtotal = 1440 + 18 + 10 + 17, + .vrefresh = 60, + .clock = 69000, + .flags = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC, + .width_mm = 68, + .height_mm = 136, +}; + +static const struct st7703_panel_desc xbd599_desc = { + .mode = &xbd599_mode, + .lanes = 4, + .mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_SYNC_PULSE, + .format = MIPI_DSI_FMT_RGB888, + .init_sequence = xbd599_init_sequence, +}; + static int st7703_enable(struct drm_panel *panel) { struct st7703 *ctx = panel_to_st7703(panel); @@ -428,6 +623,7 @@ static int st7703_remove(struct mipi_dsi_device *dsi)
static const struct of_device_id st7703_of_match[] = { { .compatible = "rocktech,jh057n00900", .data = &jh057n00900_panel_desc }, + { .compatible = "xingbangda,xbd599", .data = &xbd599_desc }, { /* sentinel */ } }; MODULE_DEVICE_TABLE(of, st7703_of_match);