Hi Wen,
On Thu, Aug 22, 2019 at 10:11:35AM +0800, Wen He wrote:
Configure the display Quality of service (QoS) levels priority if the optional property node "arm,malidp-aqros-value" is defined in DTS file.
QoS signaling using AQROS and AWQOS AXI interface signals, the AQROS is driven from the "RQOS" register, so needed to program the RQOS register to avoid the high resolutions flicker issue on the LS1028A platform.
Signed-off-by: Wen He wen.he_1@nxp.com
drivers/gpu/drm/arm/malidp_drv.c | 6 ++++++ drivers/gpu/drm/arm/malidp_hw.c | 13 +++++++++++++ drivers/gpu/drm/arm/malidp_hw.h | 3 +++ drivers/gpu/drm/arm/malidp_regs.h | 10 ++++++++++ 4 files changed, 32 insertions(+)
diff --git a/drivers/gpu/drm/arm/malidp_drv.c b/drivers/gpu/drm/arm/malidp_drv.c index c27ff456eddc..80e8d15760ac 100644 --- a/drivers/gpu/drm/arm/malidp_drv.c +++ b/drivers/gpu/drm/arm/malidp_drv.c @@ -815,6 +815,12 @@ static int malidp_bind(struct device *dev)
malidp->core_id = version;
- ret = of_property_read_u32(dev->of_node,
"arm,malidp-arqos-value",&hwdev->arqos_value);- if (ret)
hwdev->arqos_value = 0x0;- /* set the number of lines used for output of RGB data */ ret = of_property_read_u8_array(dev->of_node, "arm,malidp-output-port-lines",
diff --git a/drivers/gpu/drm/arm/malidp_hw.c b/drivers/gpu/drm/arm/malidp_hw.c index 380be66d4c6e..f90a367a5bc9 100644 --- a/drivers/gpu/drm/arm/malidp_hw.c +++ b/drivers/gpu/drm/arm/malidp_hw.c @@ -374,6 +374,19 @@ static void malidp500_modeset(struct malidp_hw_device *hwdev, struct videomode * malidp_hw_setbits(hwdev, MALIDP_DISP_FUNC_ILACED, MALIDP_DE_DISPLAY_FUNC); else malidp_hw_clearbits(hwdev, MALIDP_DISP_FUNC_ILACED, MALIDP_DE_DISPLAY_FUNC);
- /*
* Program the RQoS register to avoid high resolutions flicker* issue on the LS1028A.*/- if (hwdev->arqos_value) {
val = hwdev->arqos_value;if (mode->pixelclock > 148500000)malidp_hw_setbits(hwdev, val, MALIDP500_RQOS_QUALITY);elsemalidp_hw_clearbits(hwdev, val, MALIDP500_RQOS_QUALITY);- }
This application of the arqos_value based on a pixel clock value bothers me, because it has two problems:
1. Some other user of the Mali DP driver can't apply a system QoS value that they can now specify in the DT, unless the requested pixel clock is bigger than 145MHz. :(
2. (A guess) The flickering issue shows up on a combination of pixelclock and resolution (i.e. it is a bandwidth problem), but you only address one of the variables. Haven't tested on the LS1028A yet, but do you know if (theoretically) it would have a flicker problem doing 640x480@200MHz without the QoS value?
How about this instead?
--8<--------------------------------------------------------------------- diff --git a/drivers/gpu/drm/arm/malidp_hw.c b/drivers/gpu/drm/arm/malidp_hw.c index 380be66d4c6eb..e2f96dce13850 100644 --- a/drivers/gpu/drm/arm/malidp_hw.c +++ b/drivers/gpu/drm/arm/malidp_hw.c @@ -374,6 +374,22 @@ static void malidp500_modeset(struct malidp_hw_device *hwdev, struct videomode * malidp_hw_setbits(hwdev, MALIDP_DISP_FUNC_ILACED, MALIDP_DE_DISPLAY_FUNC); else malidp_hw_clearbits(hwdev, MALIDP_DISP_FUNC_ILACED, MALIDP_DE_DISPLAY_FUNC); + + /* + * Program the RQoS register. LS1028A has an issue where screen will + * flicker on pixelclocks higher than 148.5MHz but otherwise doesn't + * want an RQoS value, so special case it for them. + */ + if (hwdev->arqos_value) { + val = hwdev->arqos_value; + +#ifdef MALIDP_LS1028A + if (mode->pixelclock <= 148500000) + malidp_hw_clearbits(hwdev, val, MALIDP500_RQOS_QUALITY); + else +#endif + malidp_hw_setbits(hwdev, val, MALIDP500_RQOS_QUALITY); + } }
int malidp_format_get_bpp(u32 fmt) --8<---------------------------------------------------------------------
And then you need to define a MALIDP_LS1028A in a vendor patch on top of the kernel source code.
Best regards, Liviu
}
int malidp_format_get_bpp(u32 fmt) diff --git a/drivers/gpu/drm/arm/malidp_hw.h b/drivers/gpu/drm/arm/malidp_hw.h index 968a65eed371..e4c36bc90bda 100644 --- a/drivers/gpu/drm/arm/malidp_hw.h +++ b/drivers/gpu/drm/arm/malidp_hw.h @@ -251,6 +251,9 @@ struct malidp_hw_device {
/* size of memory used for rotating layers, up to two banks available */ u32 rotation_memory[2];
- /* priority level of RQOS register used for driven the ARQOS signal */
- u32 arqos_value;
};
static inline u32 malidp_hw_read(struct malidp_hw_device *hwdev, u32 reg) diff --git a/drivers/gpu/drm/arm/malidp_regs.h b/drivers/gpu/drm/arm/malidp_regs.h index 993031542fa1..514c50dcb74d 100644 --- a/drivers/gpu/drm/arm/malidp_regs.h +++ b/drivers/gpu/drm/arm/malidp_regs.h @@ -210,6 +210,16 @@ #define MALIDP500_CONFIG_VALID 0x00f00 #define MALIDP500_CONFIG_ID 0x00fd4
+/*
- The quality of service (QoS) register on the DP500. RQOS register values
- are driven by the ARQOS signal, using AXI transacations, dependent on the
- FIFO input level.
- The RQOS register can also set QoS levels for:
- RED_ARQOS @ A 4-bit signal value for close to underflow conditions
- GREEN_ARQOS @ A 4-bit signal value for normal conditions
- */
+#define MALIDP500_RQOS_QUALITY 0x00500
/* register offsets and bits specific to DP550/DP650 */ #define MALIDP550_ADDR_SPACE_SIZE 0x10000
#define MALIDP550_DE_CONTROL 0x00010
2.17.1