From: Jeykumar Sankaran jsanka@codeaurora.org
Adds bindings for Snapdragon 845 display processing unit
Changes in v2: - Use SoC specific compatibles for mdss and dpu - Use assigned-clocks to set initial clock frequency
Signed-off-by: Jeykumar Sankaran jsanka@codeaurora.org Signed-off-by: Rajesh Yadav ryadav@codeaurora.org Signed-off-by: Sean Paul seanpaul@chromium.org --- .../devicetree/bindings/display/msm/dpu.txt | 136 ++++++++++++++++++ 1 file changed, 136 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/msm/dpu.txt
diff --git a/Documentation/devicetree/bindings/display/msm/dpu.txt b/Documentation/devicetree/bindings/display/msm/dpu.txt new file mode 100644 index 000000000000..a998028896ba --- /dev/null +++ b/Documentation/devicetree/bindings/display/msm/dpu.txt @@ -0,0 +1,136 @@ +Qualcomm Technologies, Inc. DPU KMS + +Description: + +Device tree bindings for MSM Mobile Display Subsytem(MDSS) that encapsulates +sub-blocks like DPU display controller, DSI and DP interfaces etc. +The DPU display controller is found in SDM845 SoC. + +MDSS: +Required properties: +- compatible: "qcom,sdm845-mdss" +- reg: physical base address and length of contoller's registers. +- reg-names: register region names. The following region is required: + * "mdss_phys" +- power-domains: a power domain consumer specifier according to + Documentation/devicetree/bindings/power/power_domain.txt +- clocks: list of phandles for clock device nodes needed by the device. +- clock-names: device clock names, must be in same order as clocks property. + The following clocks are required: + * "iface" + * "bus" + * "core" +- interrupts: interrupt signal from MDSS. +- interrupt-controller: identifies the node as an interrupt controller. +- #interrupt-cells: specifies the number of cells needed to encode an interrupt + source, should be 1. +- iommus: phandle of iommu device node. +- #address-cells: number of address cells for the MDSS children. Should be 1. +- #size-cells: Should be 1. +- ranges: parent bus address space is the same as the child bus address space. + +Optional properties: +- assigned-clocks: list of phandles for clock device nodes needing rate + assignment +- assigned-clock-rates: list of clock frequencies sorted in the same order as + the assigned-clocks property. + +MDP: +Required properties: +- compatible: "qcom,sdm845-dpu" +- reg: physical base address and length of controller's registers. +- reg-names : register region names. The following region is required: + * "mdp_phys" + * "vbif_phys" +- clocks: list of phandles for clock device nodes needed by the device. +- clock-names: device clock names, must be in same order as clocks property. + The following clocks are required. + * "bus" + * "iface" + * "core" + * "vsync" +- interrupt-parent: phandle to MDSS block. +- interrupts: interrupt line from DPU to MDSS. +- ports: contains the list of output ports from DPU device. These ports connect + to interfaces that are external to the DPU hardware, such as DSI, DP etc. + + Each output port contains an endpoint that describes how it is connected to an + external interface. These are described by the standard properties documented + here: + Documentation/devicetree/bindings/graph.txt + Documentation/devicetree/bindings/media/video-interfaces.txt + + Port 0 -> DPU_INTF1 (DSI1) + Port 1 -> DPU_INTF2 (DSI2) + +Optional properties: +- assigned-clocks: list of phandles for clock device nodes needing rate + assignment +- assigned-clock-rates: list of clock frequencies sorted in the same order as + the assigned-clocks property. + +Example: + + mdss: mdss@ae00000 { + compatible = "qcom,sdm845-mdss"; + reg = <0xae00000 0x1000>; + reg-names = "mdss_phys"; + + power-domains = <&clock_dispcc 0>; + + clocks = <&gcc GCC_DISP_AHB_CLK>, <&gcc GCC_DISP_AXI_CLK>, + <&clock_dispcc DISP_CC_MDSS_MDP_CLK>; + clock-names = "iface", "bus", "core"; + + assigned-clocks = <&clock_dispcc DISP_CC_MDSS_MDP_CLK>; + assigned-clock-rates = <300000000>; + + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <1>; + + iommus = <&apps_iommu 0>; + + #address-cells = <1>; + #size-cells = <1>; + ranges; + + mdss_mdp: mdp@ae01000 { + compatible = "qcom,sdm845-dpu"; + reg = <0x0ae01000 0x8f000>, + <0x0aeb0000 0x2008>; + reg-names = "mdp_phys", "vbif_phys"; + + clocks = <&clock_dispcc DISP_CC_MDSS_AHB_CLK>, + <&clock_dispcc DISP_CC_MDSS_AXI_CLK>, + <&clock_dispcc DISP_CC_MDSS_MDP_CLK>, + <&clock_dispcc DISP_CC_MDSS_VSYNC_CLK>; + clock-names = "iface", "bus", "core", "vsync"; + + assigned-clocks = <&clock_dispcc DISP_CC_MDSS_MDP_CLK>, + <&clock_dispcc DISP_CC_MDSS_VSYNC_CLK>; + assigned-clock-rates = <0 0 300000000 19200000>; + + interrupt-parent = <&mdss>; + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + dpu_intf1_out: endpoint { + remote-endpoint = <&dsi0_in>; + }; + }; + + port@1 { + reg = <1>; + dpu_intf2_out: endpoint { + remote-endpoint = <&dsi1_in>; + }; + }; + }; + }; + };