Since we're about to implement eDP backlight support in nouveau using the standard protocol from VESA, we might as well just take the code that's already written for this and move it into a set of shared DRM helpers.
Note that these helpers are intended to handle DPCD related backlight control bits such as setting the brightness level over AUX, probing the backlight's TCON, enabling/disabling the backlight over AUX if supported, etc. Any PWM-related portions of backlight control are explicitly left up to the driver, as these will vary from platform to platform.
The only exception to this is the calculation of the PWM frequency pre-divider value. This is because the only platform-specific information required for this is the PWM frequency of the panel, which the driver is expected to provide if available. The actual algorithm for calculating this value is standard and is defined in the eDP specification from VESA.
Note that these helpers do not yet implement the full range of features the VESA backlight interface provides, and only provide the following functionality (all of which was already present in i915's DPCD backlight support):
* Basic control of brightness levels * Basic probing of backlight capabilities * Helpers for enabling and disabling the backlight
Signed-off-by: Lyude Paul lyude@redhat.com Cc: Jani Nikula jani.nikula@intel.com Cc: Dave Airlie airlied@gmail.com Cc: greg.depoire@gmail.com --- drivers/gpu/drm/drm_dp_helper.c | 332 ++++++++++++++++++ .../drm/i915/display/intel_display_types.h | 5 +- .../drm/i915/display/intel_dp_aux_backlight.c | 304 ++-------------- include/drm/drm_dp_helper.h | 48 +++ 4 files changed, 419 insertions(+), 270 deletions(-)
diff --git a/drivers/gpu/drm/drm_dp_helper.c b/drivers/gpu/drm/drm_dp_helper.c index 5bd0934004e3..06fdddf44e54 100644 --- a/drivers/gpu/drm/drm_dp_helper.c +++ b/drivers/gpu/drm/drm_dp_helper.c @@ -2596,3 +2596,335 @@ void drm_dp_vsc_sdp_log(const char *level, struct device *dev, #undef DP_SDP_LOG } EXPORT_SYMBOL(drm_dp_vsc_sdp_log); + +/** + * drm_edp_backlight_set_level() - Set the backlight level of an eDP panel via AUX + * @aux: The DP AUX channel to use + * @bl: Backlight capability info from drm_edp_backlight_init() + * @level: The brightness level to set + * + * Sets the brightness level of an eDP panel's backlight. Note that the panel's backlight must + * already have been enabled by the driver by calling drm_edp_backlight_enable(). + * + * Returns: %0 on success, negative error code on failure + */ +int drm_edp_backlight_set_level(struct drm_dp_aux *aux, const struct drm_edp_backlight_info *bl, + u16 level) +{ + int ret; + u8 buf[2] = { 0 }; + + if (bl->lsb_reg_used) { + buf[0] = (level & 0xFF00) >> 8; + buf[1] = (level & 0x00FF); + } else { + buf[0] = level; + } + + ret = drm_dp_dpcd_write(aux, DP_EDP_BACKLIGHT_BRIGHTNESS_MSB, buf, sizeof(buf)); + if (ret != sizeof(buf)) { + DRM_ERROR("%s: Failed to write aux backlight level: %d\n", aux->name, ret); + return ret < 0 ? ret : -EIO; + } + + return 0; +} +EXPORT_SYMBOL(drm_edp_backlight_set_level); + +static int +drm_edp_backlight_set_enable(struct drm_dp_aux *aux, const struct drm_edp_backlight_info *bl, + bool enable) +{ + int ret; + u8 buf; + + /* The panel uses something other then DPCD for enabling it's backlight */ + if (!bl->aux_enable) + return 0; + + ret = drm_dp_dpcd_readb(aux, DP_EDP_DISPLAY_CONTROL_REGISTER, &buf); + if (ret != 1) { + DRM_ERROR("%s: Failed to read eDP display control register: %d\n", aux->name, ret); + return ret < 0 ? ret : -EIO; + } + if (enable) + buf |= DP_EDP_BACKLIGHT_ENABLE; + else + buf &= ~DP_EDP_BACKLIGHT_ENABLE; + + ret = drm_dp_dpcd_writeb(aux, DP_EDP_DISPLAY_CONTROL_REGISTER, buf); + if (ret != 1) { + DRM_ERROR("%s: Failed to write eDP display control register: %d\n", aux->name, ret); + return ret < 0 ? ret : -EIO; + } + + return 0; +} + +/** + * drm_edp_backlight_enable() - Enable an eDP panel's backlight using DPCD + * @aux: The DP AUX channel to use + * @bl: Backlight capability info from drm_edp_backlight_init() + * @level: The initial backlight level to set via AUX, if there is one + * + * This function handles enabling DPCD backlight controls on a panel over DPCD, while additionally + * restoring any important backlight state such as the given backlight level, the brightness byte + * count, backlight frequency, etc. + * + * Note that certain panels, while supporting brightness level controls over DPCD, may not support + * having their backlights enabled via the standard %DP_EDP_DISPLAY_CONTROL_REGISTER. On such panels + * &drm_edp_backlight_info.aux_enable will be set to %false, this function will skip the step of + * programming the %DP_EDP_DISPLAY_CONTROL_REGISTER, and the driver must perform the required + * implementation specific step for enabling the backlight after calling this function. + * + * Returns: %0 on success, negative error code on failure. + */ +int drm_edp_backlight_enable(struct drm_dp_aux *aux, const struct drm_edp_backlight_info *bl, + const u16 level) +{ + int ret; + u8 dpcd_buf, new_dpcd_buf; + + ret = drm_dp_dpcd_readb(aux, DP_EDP_BACKLIGHT_MODE_SET_REGISTER, &dpcd_buf); + if (ret != 1) { + DRM_DEBUG_KMS("%s: Failed to read backlight mode: %d\n", aux->name, ret); + return ret < 0 ? ret : -EIO; + } + + new_dpcd_buf = dpcd_buf; + + if ((dpcd_buf & DP_EDP_BACKLIGHT_CONTROL_MODE_MASK) != DP_EDP_BACKLIGHT_CONTROL_MODE_DPCD) { + new_dpcd_buf &= ~DP_EDP_BACKLIGHT_CONTROL_MODE_MASK; + new_dpcd_buf |= DP_EDP_BACKLIGHT_CONTROL_MODE_DPCD; + + ret = drm_dp_dpcd_writeb(aux, DP_EDP_PWMGEN_BIT_COUNT, bl->pwmgen_bit_count); + if (ret != 1) + DRM_DEBUG_KMS("%s: Failed to write aux pwmgen bit count: %d\n", + aux->name, ret); + } + + if (bl->pwm_freq_pre_divider) { + ret = drm_dp_dpcd_writeb(aux, DP_EDP_BACKLIGHT_FREQ_SET, bl->pwm_freq_pre_divider); + if (ret != 1) + DRM_DEBUG_KMS("%s: Failed to write aux backlight frequency: %d\n", + aux->name, ret); + else + new_dpcd_buf |= DP_EDP_BACKLIGHT_FREQ_AUX_SET_ENABLE; + } + + if (new_dpcd_buf != dpcd_buf) { + ret = drm_dp_dpcd_writeb(aux, DP_EDP_BACKLIGHT_MODE_SET_REGISTER, new_dpcd_buf); + if (ret != 1) { + DRM_DEBUG_KMS("%s: Failed to write aux backlight mode: %d\n", + aux->name, ret); + return ret < 0 ? ret : -EIO; + } + } + + ret = drm_edp_backlight_set_level(aux, bl, level); + if (ret < 0) + return ret; + ret = drm_edp_backlight_set_enable(aux, bl, true); + if (ret < 0) + return ret; + + return 0; +} +EXPORT_SYMBOL(drm_edp_backlight_enable); + +/** + * drm_edp_backlight_disable() - Disable an eDP backlight using DPCD, if supported + * @aux: The DP AUX channel to use + * @bl: Backlight capability info from drm_edp_backlight_init() + * + * This function handles disabling DPCD backlight controls on a panel over AUX. Note that some + * panels have backlights that are enabled/disabled by other means, despite having their brightness + * values controlled through DPCD. On such panels &drm_edp_backlight_info.aux_enable will be set to + * %false, this function will become a no-op (and we will skip updating + * %DP_EDP_DISPLAY_CONTROL_REGISTER), and the driver must take care to perform it's own + * implementation specific step for disabling the backlight. + * + * Returns: %0 on success or no-op, negative error code on failure. + */ +int drm_edp_backlight_disable(struct drm_dp_aux *aux, const struct drm_edp_backlight_info *bl) +{ + int ret; + + ret = drm_edp_backlight_set_enable(aux, bl, false); + if (ret < 0) + return ret; + + return 0; +} +EXPORT_SYMBOL(drm_edp_backlight_disable); + +static inline int +drm_edp_backlight_probe_max(struct drm_dp_aux *aux, struct drm_edp_backlight_info *bl, + u16 driver_pwm_freq_hz, const u8 edp_dpcd[EDP_DISPLAY_CTL_CAP_SIZE]) +{ + int fxp, fxp_min, fxp_max, fxp_actual, f = 1; + int ret; + u8 pn, pn_min, pn_max; + + ret = drm_dp_dpcd_readb(aux, DP_EDP_PWMGEN_BIT_COUNT, &pn); + if (ret != 1) { + DRM_DEBUG_KMS("%s: Failed to read pwmgen bit count cap: %d\n", aux->name, ret); + return -ENODEV; + } + + pn &= DP_EDP_PWMGEN_BIT_COUNT_MASK; + bl->max = (1 << pn) - 1; + if (!driver_pwm_freq_hz) + return 0; + + /* + * Set PWM Frequency divider to match desired frequency provided by the driver. + * The PWM Frequency is calculated as 27Mhz / (F x P). + * - Where F = PWM Frequency Pre-Divider value programmed by field 7:0 of the + * EDP_BACKLIGHT_FREQ_SET register (DPCD Address 00728h) + * - Where P = 2^Pn, where Pn is the value programmed by field 4:0 of the + * EDP_PWMGEN_BIT_COUNT register (DPCD Address 00724h) + */ + + /* Find desired value of (F x P) + * Note that, if F x P is out of supported range, the maximum value or minimum value will + * applied automatically. So no need to check that. + */ + fxp = DIV_ROUND_CLOSEST(1000 * DP_EDP_BACKLIGHT_FREQ_BASE_KHZ, driver_pwm_freq_hz); + + /* Use highest possible value of Pn for more granularity of brightness adjustment while + * satifying the conditions below. + * - Pn is in the range of Pn_min and Pn_max + * - F is in the range of 1 and 255 + * - FxP is within 25% of desired value. + * Note: 25% is arbitrary value and may need some tweak. + */ + ret = drm_dp_dpcd_readb(aux, DP_EDP_PWMGEN_BIT_COUNT_CAP_MIN, &pn_min); + if (ret != 1) { + DRM_DEBUG_KMS("%s: Failed to read pwmgen bit count cap min: %d\n", aux->name, ret); + return 0; + } + ret = drm_dp_dpcd_readb(aux, DP_EDP_PWMGEN_BIT_COUNT_CAP_MAX, &pn_max); + if (ret != 1) { + DRM_DEBUG_KMS("%s: Failed to read pwmgen bit count cap max: %d\n", aux->name, ret); + return 0; + } + pn_min &= DP_EDP_PWMGEN_BIT_COUNT_MASK; + pn_max &= DP_EDP_PWMGEN_BIT_COUNT_MASK; + + /* Ensure frequency is within 25% of desired value */ + fxp_min = DIV_ROUND_CLOSEST(fxp * 3, 4); + fxp_max = DIV_ROUND_CLOSEST(fxp * 5, 4); + if (fxp_min < (1 << pn_min) || (255 << pn_max) < fxp_max) { + DRM_DEBUG_KMS("%s: Driver defined backlight frequency (%d) out of range\n", + aux->name, driver_pwm_freq_hz); + return 0; + } + + for (pn = pn_max; pn >= pn_min; pn--) { + f = clamp(DIV_ROUND_CLOSEST(fxp, 1 << pn), 1, 255); + fxp_actual = f << pn; + if (fxp_min <= fxp_actual && fxp_actual <= fxp_max) + break; + } + + ret = drm_dp_dpcd_writeb(aux, DP_EDP_PWMGEN_BIT_COUNT, pn); + if (ret != 1) { + DRM_DEBUG_KMS("%s: Failed to write aux pwmgen bit count: %d\n", aux->name, ret); + return 0; + } + bl->pwmgen_bit_count = pn; + bl->max = (1 << pn) - 1; + + if (edp_dpcd[2] & DP_EDP_BACKLIGHT_FREQ_AUX_SET_CAP) { + bl->pwm_freq_pre_divider = f; + DRM_DEBUG_KMS("%s: Using backlight frequency from driver (%dHz)\n", + aux->name, driver_pwm_freq_hz); + } + + return 0; +} + +static inline int +drm_edp_backlight_probe_level(struct drm_dp_aux *aux, struct drm_edp_backlight_info *bl, + u8 *current_mode) +{ + int ret; + u8 buf[2]; + u8 mode_reg; + + ret = drm_dp_dpcd_readb(aux, DP_EDP_BACKLIGHT_MODE_SET_REGISTER, &mode_reg); + if (ret != 1) { + DRM_DEBUG_KMS("%s: Failed to read backlight mode: %d\n", aux->name, ret); + return ret < 0 ? ret : -EIO; + } + + *current_mode = (mode_reg & DP_EDP_BACKLIGHT_CONTROL_MODE_MASK); + if (*current_mode == DP_EDP_BACKLIGHT_CONTROL_MODE_DPCD) { + int size = 1 + bl->lsb_reg_used; + + ret = drm_dp_dpcd_read(aux, DP_EDP_BACKLIGHT_BRIGHTNESS_MSB, buf, size); + if (ret != size) { + DRM_DEBUG_KMS("%s: Failed to read backlight level: %d\n", aux->name, ret); + return ret < 0 ? ret : -EIO; + } + + if (bl->lsb_reg_used) + return (buf[0] << 8) | buf[1]; + else + return buf[0]; + } + + /* + * If we're not in DPCD control mode yet, the programmed brightness value is meaningless and + * the driver should assume max brightness + */ + return bl->max; +} + +/** + * drm_edp_backlight_init() - Probe a display panel's TCON using the standard VESA eDP backlight + * interface. + * @aux: The DP aux device to use for probing + * @bl: The &drm_edp_backlight_info struct to fill out with information on the backlight + * @driver_pwm_freq_hz: Optional PWM frequency from the driver in hz + * @edp_dpcd: A cached copy of the eDP DPCD + * @current_level: Where to store the probed brightness level + * @current_mode: Where to store the currently set backlight control mode + * + * Initializes a &drm_edp_backlight_info struct by probing @aux for it's backlight capabilities, + * along with also probing the current and maximum supported brightness levels. + * + * If @driver_pwm_freq_hz is non-zero, this will be used as the backlight frequency. Otherwise, the + * default frequency from the panel is used. + * + * Returns: %0 on success, negative error code on failure. + */ +int +drm_edp_backlight_init(struct drm_dp_aux *aux, struct drm_edp_backlight_info *bl, + u16 driver_pwm_freq_hz, const u8 edp_dpcd[EDP_DISPLAY_CTL_CAP_SIZE], + u16 *current_level, u8 *current_mode) +{ + int ret; + + if (edp_dpcd[1] & DP_EDP_BACKLIGHT_AUX_ENABLE_CAP) + bl->aux_enable = true; + if (edp_dpcd[2] & DP_EDP_BACKLIGHT_BRIGHTNESS_BYTE_COUNT) + bl->lsb_reg_used = true; + + ret = drm_edp_backlight_probe_max(aux, bl, driver_pwm_freq_hz, edp_dpcd); + if (ret < 0) + return ret; + + ret = drm_edp_backlight_probe_level(aux, bl, current_mode); + if (ret < 0) + return ret; + *current_level = ret; + + DRM_DEBUG_KMS("%s: Found backlight level=%d/%d pwm_freq_pre_divider=%d mode=%x\n", + aux->name, *current_level, bl->max, bl->pwm_freq_pre_divider, *current_mode); + DRM_DEBUG_KMS("%s: Backlight caps: pwmgen_bit_count=%d lsb_reg_used=%d aux_enable=%d\n", + aux->name, bl->pwmgen_bit_count, bl->lsb_reg_used, bl->aux_enable); + return 0; +} +EXPORT_SYMBOL(drm_edp_backlight_init); diff --git a/drivers/gpu/drm/i915/display/intel_display_types.h b/drivers/gpu/drm/i915/display/intel_display_types.h index 133c9cb742a7..82673e8f21c3 100644 --- a/drivers/gpu/drm/i915/display/intel_display_types.h +++ b/drivers/gpu/drm/i915/display/intel_display_types.h @@ -257,11 +257,8 @@ struct intel_panel { struct pwm_device *pwm; struct pwm_state pwm_state;
- /* DPCD backlight */ - u8 pwmgen_bit_count; - u8 pwm_freq_pre_divider; - struct backlight_device *device; + struct drm_edp_backlight_info vesa_edp_info;
const struct intel_panel_bl_funcs *funcs; void (*power)(struct intel_connector *, bool enable); diff --git a/drivers/gpu/drm/i915/display/intel_dp_aux_backlight.c b/drivers/gpu/drm/i915/display/intel_dp_aux_backlight.c index 94ce5ca1affa..b1ebfd854a42 100644 --- a/drivers/gpu/drm/i915/display/intel_dp_aux_backlight.c +++ b/drivers/gpu/drm/i915/display/intel_dp_aux_backlight.c @@ -25,303 +25,73 @@ #include "intel_display_types.h" #include "intel_dp_aux_backlight.h"
-static void set_aux_backlight_enable(struct intel_dp *intel_dp, bool enable) -{ - struct drm_i915_private *i915 = dp_to_i915(intel_dp); - u8 reg_val = 0; - - /* Early return when display use other mechanism to enable backlight. */ - if (!(intel_dp->edp_dpcd[1] & DP_EDP_BACKLIGHT_AUX_ENABLE_CAP)) - return; - - if (drm_dp_dpcd_readb(&intel_dp->aux, DP_EDP_DISPLAY_CONTROL_REGISTER, - ®_val) < 0) { - drm_dbg_kms(&i915->drm, "Failed to read DPCD register 0x%x\n", - DP_EDP_DISPLAY_CONTROL_REGISTER); - return; - } - if (enable) - reg_val |= DP_EDP_BACKLIGHT_ENABLE; - else - reg_val &= ~(DP_EDP_BACKLIGHT_ENABLE); - - if (drm_dp_dpcd_writeb(&intel_dp->aux, DP_EDP_DISPLAY_CONTROL_REGISTER, - reg_val) != 1) { - drm_dbg_kms(&i915->drm, "Failed to %s aux backlight\n", - enable ? "enable" : "disable"); - } -} - -static bool intel_dp_aux_backlight_dpcd_mode(struct intel_connector *connector) -{ - struct intel_dp *intel_dp = intel_attached_dp(connector); - struct drm_i915_private *i915 = dp_to_i915(intel_dp); - u8 mode_reg; - - if (drm_dp_dpcd_readb(&intel_dp->aux, - DP_EDP_BACKLIGHT_MODE_SET_REGISTER, - &mode_reg) != 1) { - drm_dbg_kms(&i915->drm, - "Failed to read the DPCD register 0x%x\n", - DP_EDP_BACKLIGHT_MODE_SET_REGISTER); - return false; - } - - return (mode_reg & DP_EDP_BACKLIGHT_CONTROL_MODE_MASK) == - DP_EDP_BACKLIGHT_CONTROL_MODE_DPCD; -} - -/* - * Read the current backlight value from DPCD register(s) based - * on if 8-bit(MSB) or 16-bit(MSB and LSB) values are supported - */ static u32 intel_dp_aux_get_backlight(struct intel_connector *connector) { - struct intel_dp *intel_dp = intel_attached_dp(connector); - struct drm_i915_private *i915 = dp_to_i915(intel_dp); - u8 read_val[2] = { 0x0 }; - u16 level = 0; - - /* - * If we're not in DPCD control mode yet, the programmed brightness - * value is meaningless and we should assume max brightness - */ - if (!intel_dp_aux_backlight_dpcd_mode(connector)) - return connector->panel.backlight.max; - - if (drm_dp_dpcd_read(&intel_dp->aux, DP_EDP_BACKLIGHT_BRIGHTNESS_MSB, - &read_val, sizeof(read_val)) < 0) { - drm_dbg_kms(&i915->drm, "Failed to read DPCD register 0x%x\n", - DP_EDP_BACKLIGHT_BRIGHTNESS_MSB); - return 0; - } - level = read_val[0]; - if (intel_dp->edp_dpcd[2] & DP_EDP_BACKLIGHT_BRIGHTNESS_BYTE_COUNT) - level = (read_val[0] << 8 | read_val[1]); - - return level; + return connector->panel.backlight.level; }
-/* - * Sends the current backlight level over the aux channel, checking if its using - * 8-bit or 16 bit value (MSB and LSB) - */ static void -intel_dp_aux_set_backlight(const struct drm_connector_state *conn_state, u32 level) +intel_dp_aux_set_backlight(const struct drm_connector_state *conn_state, + u32 level) { struct intel_connector *connector = to_intel_connector(conn_state->connector); - struct intel_dp *intel_dp = intel_attached_dp(connector); - struct drm_i915_private *i915 = dp_to_i915(intel_dp); - u8 vals[2] = { 0x0 }; - - vals[0] = level; + struct intel_panel *panel = &connector->panel; + struct intel_dp *intel_dp = enc_to_intel_dp(connector->encoder);
- /* Write the MSB and/or LSB */ - if (intel_dp->edp_dpcd[2] & DP_EDP_BACKLIGHT_BRIGHTNESS_BYTE_COUNT) { - vals[0] = (level & 0xFF00) >> 8; - vals[1] = (level & 0xFF); - } - if (drm_dp_dpcd_write(&intel_dp->aux, DP_EDP_BACKLIGHT_BRIGHTNESS_MSB, - vals, sizeof(vals)) < 0) { - drm_dbg_kms(&i915->drm, - "Failed to write aux backlight level\n"); - return; - } + drm_edp_backlight_set_level(&intel_dp->aux, &panel->backlight.vesa_edp_info, level); }
-static void intel_dp_aux_enable_backlight(const struct intel_crtc_state *crtc_state, - const struct drm_connector_state *conn_state) +static void +intel_dp_aux_enable_backlight(const struct intel_crtc_state *crtc_state, + const struct drm_connector_state *conn_state) { struct intel_connector *connector = to_intel_connector(conn_state->connector); - struct intel_dp *intel_dp = intel_attached_dp(connector); - struct drm_i915_private *i915 = dp_to_i915(intel_dp); struct intel_panel *panel = &connector->panel; - u8 dpcd_buf, new_dpcd_buf, edp_backlight_mode; - - if (drm_dp_dpcd_readb(&intel_dp->aux, - DP_EDP_BACKLIGHT_MODE_SET_REGISTER, &dpcd_buf) != 1) { - drm_dbg_kms(&i915->drm, "Failed to read DPCD register 0x%x\n", - DP_EDP_BACKLIGHT_MODE_SET_REGISTER); - return; - } - - new_dpcd_buf = dpcd_buf; - edp_backlight_mode = dpcd_buf & DP_EDP_BACKLIGHT_CONTROL_MODE_MASK; - - switch (edp_backlight_mode) { - case DP_EDP_BACKLIGHT_CONTROL_MODE_PWM: - case DP_EDP_BACKLIGHT_CONTROL_MODE_PRESET: - case DP_EDP_BACKLIGHT_CONTROL_MODE_PRODUCT: - new_dpcd_buf &= ~DP_EDP_BACKLIGHT_CONTROL_MODE_MASK; - new_dpcd_buf |= DP_EDP_BACKLIGHT_CONTROL_MODE_DPCD; - - if (drm_dp_dpcd_writeb(&intel_dp->aux, - DP_EDP_PWMGEN_BIT_COUNT, - panel->backlight.pwmgen_bit_count) < 0) - drm_dbg_kms(&i915->drm, - "Failed to write aux pwmgen bit count\n"); - - break; - - /* Do nothing when it is already DPCD mode */ - case DP_EDP_BACKLIGHT_CONTROL_MODE_DPCD: - default: - break; - } - - if (panel->backlight.pwm_freq_pre_divider) { - if (drm_dp_dpcd_writeb(&intel_dp->aux, DP_EDP_BACKLIGHT_FREQ_SET, - panel->backlight.pwm_freq_pre_divider) == 1) - new_dpcd_buf |= DP_EDP_BACKLIGHT_FREQ_AUX_SET_ENABLE; - else - drm_dbg_kms(&i915->drm, "Failed to write aux backlight frequency\n"); - } + struct intel_dp *intel_dp = enc_to_intel_dp(connector->encoder);
- if (new_dpcd_buf != dpcd_buf) { - if (drm_dp_dpcd_writeb(&intel_dp->aux, - DP_EDP_BACKLIGHT_MODE_SET_REGISTER, new_dpcd_buf) < 0) { - drm_dbg_kms(&i915->drm, - "Failed to write aux backlight mode\n"); - } - } - - intel_dp_aux_set_backlight(conn_state, - connector->panel.backlight.level); - set_aux_backlight_enable(intel_dp, true); + drm_edp_backlight_enable(&intel_dp->aux, &panel->backlight.vesa_edp_info, + panel->backlight.level); }
-static void intel_dp_aux_disable_backlight(const struct drm_connector_state *old_conn_state) -{ - set_aux_backlight_enable(enc_to_intel_dp(to_intel_encoder(old_conn_state->best_encoder)), - false); -} - -/* - * Compute PWM frequency divider value based off the frequency provided to us by the vbt. - * The PWM Frequency is calculated as 27Mhz / (F x P). - * - Where F = PWM Frequency Pre-Divider value programmed by field 7:0 of the - * EDP_BACKLIGHT_FREQ_SET register (DPCD Address 00728h) - * - Where P = 2^Pn, where Pn is the value programmed by field 4:0 of the - * EDP_PWMGEN_BIT_COUNT register (DPCD Address 00724h) - */ -static u32 intel_dp_aux_calc_max_backlight(struct intel_connector *connector) +static void +intel_dp_aux_disable_backlight(const struct drm_connector_state *old_conn_state) { - struct drm_i915_private *i915 = to_i915(connector->base.dev); - struct intel_dp *intel_dp = intel_attached_dp(connector); + struct intel_connector *connector = to_intel_connector(old_conn_state->connector); struct intel_panel *panel = &connector->panel; - u32 max_backlight = 0; - int freq, fxp, fxp_min, fxp_max, fxp_actual, f = 1; - u8 pn, pn_min, pn_max; - - if (drm_dp_dpcd_readb(&intel_dp->aux, DP_EDP_PWMGEN_BIT_COUNT, &pn) == 1) { - pn &= DP_EDP_PWMGEN_BIT_COUNT_MASK; - max_backlight = (1 << pn) - 1; - } - - /* Find desired value of (F x P) - * Note that, if F x P is out of supported range, the maximum value or - * minimum value will applied automatically. So no need to check that. - */ - freq = i915->vbt.backlight.pwm_freq_hz; - drm_dbg_kms(&i915->drm, "VBT defined backlight frequency %u Hz\n", - freq); - if (!freq) { - drm_dbg_kms(&i915->drm, - "Use panel default backlight frequency\n"); - return max_backlight; - } - - fxp = DIV_ROUND_CLOSEST(KHz(DP_EDP_BACKLIGHT_FREQ_BASE_KHZ), freq); - - /* Use highest possible value of Pn for more granularity of brightness - * adjustment while satifying the conditions below. - * - Pn is in the range of Pn_min and Pn_max - * - F is in the range of 1 and 255 - * - FxP is within 25% of desired value. - * Note: 25% is arbitrary value and may need some tweak. - */ - if (drm_dp_dpcd_readb(&intel_dp->aux, - DP_EDP_PWMGEN_BIT_COUNT_CAP_MIN, &pn_min) != 1) { - drm_dbg_kms(&i915->drm, - "Failed to read pwmgen bit count cap min\n"); - return max_backlight; - } - if (drm_dp_dpcd_readb(&intel_dp->aux, - DP_EDP_PWMGEN_BIT_COUNT_CAP_MAX, &pn_max) != 1) { - drm_dbg_kms(&i915->drm, - "Failed to read pwmgen bit count cap max\n"); - return max_backlight; - } - pn_min &= DP_EDP_PWMGEN_BIT_COUNT_MASK; - pn_max &= DP_EDP_PWMGEN_BIT_COUNT_MASK; + struct intel_dp *intel_dp = enc_to_intel_dp(connector->encoder);
- /* Ensure frequency is within 25% of desired value */ - fxp_min = DIV_ROUND_CLOSEST(fxp * 3, 4); - fxp_max = DIV_ROUND_CLOSEST(fxp * 5, 4); - - if (fxp_min < (1 << pn_min) || (255 << pn_max) < fxp_max) { - drm_dbg_kms(&i915->drm, - "VBT defined backlight frequency out of range\n"); - return max_backlight; - } - - for (pn = pn_max; pn >= pn_min; pn--) { - f = clamp(DIV_ROUND_CLOSEST(fxp, 1 << pn), 1, 255); - fxp_actual = f << pn; - if (fxp_min <= fxp_actual && fxp_actual <= fxp_max) - break; - } - - drm_dbg_kms(&i915->drm, "Using eDP pwmgen bit count of %d\n", pn); - if (drm_dp_dpcd_writeb(&intel_dp->aux, - DP_EDP_PWMGEN_BIT_COUNT, pn) < 0) { - drm_dbg_kms(&i915->drm, - "Failed to write aux pwmgen bit count\n"); - return max_backlight; - } - - panel->backlight.pwmgen_bit_count = pn; - panel->backlight.pwm_freq_pre_divider = f; - - max_backlight = (1 << pn) - 1; - - return max_backlight; + drm_edp_backlight_disable(&intel_dp->aux, &panel->backlight.vesa_edp_info); }
static int intel_dp_aux_setup_backlight(struct intel_connector *connector, enum pipe pipe) { struct intel_panel *panel = &connector->panel; + struct intel_dp *intel_dp = enc_to_intel_dp(connector->encoder); + struct drm_i915_private *i915 = dp_to_i915(intel_dp); + u16 current_level; + u8 current_mode; + int ret;
- panel->backlight.max = intel_dp_aux_calc_max_backlight(connector); - if (!panel->backlight.max) - return -ENODEV; + ret = drm_edp_backlight_init(&intel_dp->aux, &panel->backlight.vesa_edp_info, + i915->vbt.backlight.pwm_freq_hz, intel_dp->edp_dpcd, + ¤t_level, ¤t_mode); + if (ret < 0) + return ret;
+ panel->backlight.max = panel->backlight.vesa_edp_info.max; panel->backlight.min = 0; - panel->backlight.level = intel_dp_aux_get_backlight(connector); - panel->backlight.enabled = intel_dp_aux_backlight_dpcd_mode(connector) && - panel->backlight.level != 0; + if (current_mode == DP_EDP_BACKLIGHT_CONTROL_MODE_DPCD) { + panel->backlight.level = current_level; + panel->backlight.enabled = panel->backlight.level != 0; + } else { + panel->backlight.level = panel->backlight.max; + panel->backlight.enabled = false; + }
return 0; }
-static bool -intel_dp_aux_display_control_capable(struct intel_connector *connector) -{ - struct intel_dp *intel_dp = intel_attached_dp(connector); - struct drm_i915_private *i915 = dp_to_i915(intel_dp); - - /* Check the eDP Display control capabilities registers to determine if - * the panel can support backlight control over the aux channel - */ - if (intel_dp->edp_dpcd[1] & DP_EDP_TCON_BACKLIGHT_ADJUSTMENT_CAP && - (intel_dp->edp_dpcd[2] & DP_EDP_BACKLIGHT_BRIGHTNESS_AUX_SET_CAP)) { - drm_dbg_kms(&i915->drm, "AUX Backlight Control Supported!\n"); - return true; - } - return false; -} - static const struct intel_panel_bl_funcs intel_dp_bl_funcs = { .setup = intel_dp_aux_setup_backlight, .enable = intel_dp_aux_enable_backlight, @@ -337,9 +107,11 @@ int intel_dp_aux_init_backlight_funcs(struct intel_connector *intel_connector) struct drm_i915_private *i915 = dp_to_i915(intel_dp);
if (i915->params.enable_dpcd_backlight == 0 || - !intel_dp_aux_display_control_capable(intel_connector)) + !drm_edp_backlight_supported(intel_dp->edp_dpcd)) return -ENODEV;
+ drm_dbg_kms(&i915->drm, "AUX Backlight Control Supported!\n"); + /* * There are a lot of machines that don't advertise the backlight * control interface to use properly in their VBIOS, :\ diff --git a/include/drm/drm_dp_helper.h b/include/drm/drm_dp_helper.h index 6b40258927bf..082fb832d4f6 100644 --- a/include/drm/drm_dp_helper.h +++ b/include/drm/drm_dp_helper.h @@ -1598,6 +1598,24 @@ drm_dp_sink_can_do_video_without_timing_msa(const u8 dpcd[DP_RECEIVER_CAP_SIZE]) DP_MSA_TIMING_PAR_IGNORED; }
+/** + * drm_edp_backlight_supported() - Check an eDP DPCD for VESA backlight support + * @edp_dpcd: The DPCD to check + * + * Note that currently this function will return %false for panels which support various DPCD + * backlight features but which require the brightness be set through PWM, and don't support setting + * the brightness level via the DPCD. This is a TODO. + * + * Returns: %True if @edp_dpcd indicates that VESA backlight controls are supported, %false + * otherwise + */ +static inline bool +drm_edp_backlight_supported(const u8 edp_dpcd[EDP_DISPLAY_CTL_CAP_SIZE]) +{ + return (edp_dpcd[1] & DP_EDP_TCON_BACKLIGHT_ADJUSTMENT_CAP) && + (edp_dpcd[2] & DP_EDP_BACKLIGHT_BRIGHTNESS_AUX_SET_CAP); +} + /* * DisplayPort AUX channel */ @@ -1912,6 +1930,36 @@ drm_dp_has_quirk(const struct drm_dp_desc *desc, u32 edid_quirks, return (desc->quirks | edid_quirks) & BIT(quirk); }
+/** + * struct drm_edp_backlight_info - Probed eDP backlight info struct + * @pwmgen_bit_count: The pwmgen bit count + * @pwm_freq_pre_divider: The PWM frequency pre-divider value being used for this backlight, if any + * @max: The maximum backlight level that may be set + * @lsb_reg_used: Do we also write values to the DP_EDP_BACKLIGHT_BRIGHTNESS_LSB register? + * @aux_enable: Does the panel support the AUX enable cap? + * + * This structure contains various data about an eDP backlight, which can be populated by using + * drm_edp_backlight_init(). + */ +struct drm_edp_backlight_info { + u8 pwmgen_bit_count; + u8 pwm_freq_pre_divider; + u16 max; + + bool lsb_reg_used : 1; + bool aux_enable : 1; +}; + +int +drm_edp_backlight_init(struct drm_dp_aux *aux, struct drm_edp_backlight_info *bl, + u16 driver_pwm_freq_hz, const u8 edp_dpcd[EDP_DISPLAY_CTL_CAP_SIZE], + u16 *current_level, u8 *current_mode); +int drm_edp_backlight_set_level(struct drm_dp_aux *aux, const struct drm_edp_backlight_info *bl, + u16 level); +int drm_edp_backlight_enable(struct drm_dp_aux *aux, const struct drm_edp_backlight_info *bl, + u16 level); +int drm_edp_backlight_disable(struct drm_dp_aux *aux, const struct drm_edp_backlight_info *bl); + #ifdef CONFIG_DRM_DP_CEC void drm_dp_cec_irq(struct drm_dp_aux *aux); void drm_dp_cec_register_connector(struct drm_dp_aux *aux,