在 2017/9/20 9:51, Sandy Huang 写道:
Hi rob, thanks for you review.
在 2017/9/19 22:46, Rob Herring 写道:
On Thu, Sep 14, 2017 at 11:43:18AM +0800, Sandy Huang wrote:
This path add support rv1108 rgb output interface driver.
Signed-off-by: Sandy Huang hjc@rock-chips.com
.../bindings/display/rockchip/rockchip-rgb.txt | 80 ++++++++++++++++++++++ 1 file changed, 80 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/rockchip/rockchip-rgb.txt
diff --git a/Documentation/devicetree/bindings/display/rockchip/rockchip-rgb.txt b/Documentation/devicetree/bindings/display/rockchip/rockchip-rgb.txt new file mode 100644 index 0000000..4164512 --- /dev/null +++ b/Documentation/devicetree/bindings/display/rockchip/rockchip-rgb.txt @@ -0,0 +1,80 @@ +Rockchip RV1108 RGB interface +================================
+Required properties: +- compatible: matching the soc type: + - "rockchip,rv1108-rgb";
+Optional properties: +- pinctrl-names: must contain a "lcdc" entry. +- pinctrl-0: pin control group to be used for this interface.
+Required nodes: +- rockchip,rgb-mode: should be "p888", "p666", "p565", "s888", "s888-dummy"
This should be a standard property. Any device with a parallel interface is going to need something like this.
so, i need to move this property to panel? or just rename rockchip,rgb-mode to rgb-mode?
+ - p888: output r8-g8-b8 at each dclk cycle for per-pixel + - p666: output r6-g6-b6 at each dclk cycle for per-pixel + - p565: output r5-g6-b5 at each dclk cycle for per-pixel + - s888: output r8-g8-b8 in three dclk cycle for per-pixel + - s888-dmmy: output r8-g8-b8-dummy in four dclk cycle for per-pixel
+The rgb has two video ports described by: + Documentation/devicetree/bindings/media/video-interfaces.txt +Their connections are modeled using the OF graph bindings specified in + Documentation/devicetree/bindings/graph.txt.
+- video port 0 for the VOP input, the remote endpoint maybe vopb/vopl/vop +- video port 1 for either a panel or subsequent encoder
+the panel described by: + Documentation/devicetree/bindings/display/panel/simple-panel.txt +Panel other required properties: +- ports for remote rgb output.
+Example:
+panel: panel { + compatible = "auo,b101ean01"; + enable-gpios = <&gpio7 21 GPIO_ACTIVE_HIGH>;
+ ports { + panel_in_rgb: endpoint { + remote-endpoint = <&rgb_out_panel>; + }; + }; +};
+For Rockchip RV1108:
+ rgb: rgb { + compatible = "rockchip,rv1108-rgb"; + pinctrl-names = "lcdc"; + pinctrl-0 = <&lcdc_ctl>; + rockchip,rgb-mode = "p888";
+ ports { + #address-cells = <1>; + #size-cells = <0>;
+ rgb_in: port@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>;
+ rgb_in_vop: endpoint@0 { + reg = <0>;
Don't need reg for a single endpoint.
ok, this will be deleted at next version.
+ remote-endpoint = <&vop_out_rgb>; + }; + };
+ rgb_out: port@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>;
+ rgb_out_panel: endpoint@0 { + reg = <0>;
ditto.
ok, this will be deleted at next version.
sorry,this can't be deleted, because rgb output remote endpoint maybe panel or convert chip, the dts node maybe like this:
panel: panel { status = "disabled"; ports { panel_in_rgb: endpoint { remote-endpoint = <&rgb_out_panel>; }; }; };
bridge: bridge { status = "okay"; ports { bridge_in_rgb: endpoint { remote-endpoint = <&rgb_out_bridge>; }; }; };
rgb_out: port@1 { reg = <1>; #address-cells = <1>; #size-cells = <0>; rgb_out_panel: endpoint@0 { reg = <0>; remote-endpoint = <&panel_in_rgb>; }; rgb_out_bridge: endpoint@1 { reg = <1>; remote-endpoint = <&bridge_in_rgb>; }; };
so rockchip_rgb_bind() @ rockchip_rgb.c use reg id to find the remote actived endpoint.
for_each_child_of_node(port, endpoint) { of_property_read_u32(endpoint, "reg", &endpoint_id); ret = drm_of_find_panel_or_bridge(dev->of_node, 1, endpoint_id, &rgb->panel, &rgb->bridge); if (!ret) break; }
+ remote-endpoint = <&panel_in_rgb>; + }; + }; + };
+ };
2.7.4
Linux-rockchip mailing list Linux-rockchip@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-rockchip