Convert mediatek,mtu3.txt to YAML schema mediatek,mtu3.yaml
Signed-off-by: Chunfeng Yun chunfeng.yun@mediatek.com --- v2: new patch --- .../devicetree/bindings/usb/mediatek,mtu3.txt | 108 --------- .../bindings/usb/mediatek,mtu3.yaml | 227 ++++++++++++++++++ 2 files changed, 227 insertions(+), 108 deletions(-) delete mode 100644 Documentation/devicetree/bindings/usb/mediatek,mtu3.txt create mode 100644 Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml
diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt b/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt deleted file mode 100644 index a82ca438aec1..000000000000 --- a/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt +++ /dev/null @@ -1,108 +0,0 @@ -The device node for Mediatek USB3.0 DRD controller - -Required properties: - - compatible : should be "mediatek,<soc-model>-mtu3", "mediatek,mtu3", - soc-model is the name of SoC, such as mt8173, mt2712 etc, - when using "mediatek,mtu3" compatible string, you need SoC specific - ones in addition, one of: - - "mediatek,mt8173-mtu3" - - reg : specifies physical base address and size of the registers - - reg-names: should be "mac" for device IP and "ippc" for IP port control - - interrupts : interrupt used by the device IP - - power-domains : a phandle to USB power domain node to control USB's - mtcmos - - vusb33-supply : regulator of USB avdd3.3v - - clocks : a list of phandle + clock-specifier pairs, one for each - entry in clock-names - - clock-names : must contain "sys_ck" for clock of controller, - the following clocks are optional: - "ref_ck", "mcu_ck" and "dma_ck"; - - phys : see usb-hcd.yaml in the current directory - - dr_mode : should be one of "host", "peripheral" or "otg", - refer to usb/generic.txt - -Optional properties: - - #address-cells, #size-cells : should be '2' if the device has sub-nodes - with 'reg' property - - ranges : allows valid 1:1 translation between child's address space and - parent's address space - - extcon : external connector for vbus and idpin changes detection, needed - when supports dual-role mode. - it's considered valid for compatibility reasons, not allowed for - new bindings, and use "usb-role-switch" property instead. - - vbus-supply : reference to the VBUS regulator, needed when supports - dual-role mode. - it's considered valid for compatibility reasons, not allowed for - new bindings, and put into a usb-connector node. - see connector/usb-connector.yaml. - - pinctrl-names : a pinctrl state named "default" is optional, and need be - defined if auto drd switch is enabled, that means the property dr_mode - is set as "otg", and meanwhile the property "mediatek,enable-manual-drd" - is not set. - - pinctrl-0 : pin control group - See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt - - - maximum-speed : valid arguments are "super-speed", "high-speed" and - "full-speed"; refer to usb/generic.txt - - usb-role-switch : use USB Role Switch to support dual-role switch, but - not extcon; see usb/generic.txt. - - enable-manual-drd : supports manual dual-role switch via debugfs; usually - used when receptacle is TYPE-A and also wants to support dual-role - mode. - - wakeup-source: enable USB remote wakeup of host mode. - - mediatek,syscon-wakeup : phandle to syscon used to access the register - of the USB wakeup glue layer between SSUSB and SPM; it depends on - "wakeup-source", and has two arguments: - - the first one : register base address of the glue layer in syscon; - - the second one : hardware version of the glue layer - - 1 : used by mt8173 etc - - 2 : used by mt2712 etc - - mediatek,u3p-dis-msk : mask to disable u3ports, bit0 for u3port0, - bit1 for u3port1, ... etc; - -additionally the properties from usb-hcd.yaml (in the current directory) are -supported. - -Sub-nodes: -The xhci should be added as subnode to mtu3 as shown in the following example -if host mode is enabled. The DT binding details of xhci can be found in: -Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt - -The port would be added as subnode if use "usb-role-switch" property. - see graph.txt - -Example: -ssusb: usb@11271000 { - compatible = "mediatek,mt8173-mtu3"; - reg = <0 0x11271000 0 0x3000>, - <0 0x11280700 0 0x0100>; - reg-names = "mac", "ippc"; - interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_LOW>; - phys = <&phy_port0 PHY_TYPE_USB3>, - <&phy_port1 PHY_TYPE_USB2>; - power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; - clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>, - <&pericfg CLK_PERI_USB0>, - <&pericfg CLK_PERI_USB1>; - clock-names = "sys_ck", "ref_ck"; - vusb33-supply = <&mt6397_vusb_reg>; - vbus-supply = <&usb_p0_vbus>; - extcon = <&extcon_usb>; - dr_mode = "otg"; - wakeup-source; - mediatek,syscon-wakeup = <&pericfg 0x400 1>; - #address-cells = <2>; - #size-cells = <2>; - ranges; - - usb_host: xhci@11270000 { - compatible = "mediatek,mt8173-xhci"; - reg = <0 0x11270000 0 0x1000>; - reg-names = "mac"; - interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; - power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; - clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>; - clock-names = "sys_ck", "ref_ck"; - vusb33-supply = <&mt6397_vusb_reg>; - }; -}; diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml b/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml new file mode 100644 index 000000000000..57ef2ced9f31 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml @@ -0,0 +1,227 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (c) 2020 MediaTek +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/usb/mediatek,mtu3.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek USB3 DRD Controller Device Tree Bindings + +maintainers: + - Chunfeng Yun chunfeng.yun@mediatek.com + +description: | + The DRD controller has a glue layer IPPC (IP Port Control), and its host is + based on xHCI. + +properties: + compatible: + items: + - enum: + - mediatek,mt2712-mtu3 + - mediatek,mt8173-mtu3 + - mediatek,mt8183-mtu3 + - const: mediatek,mtu3 + + reg: + items: + - description: the registers of device MAC + - description: the registers of IP Port Control + + reg-names: + items: + - const: mac + - const: ippc + + interrupts: + maxItems: 1 + + power-domains: + description: A phandle to USB power domain node to control USB's MTCMOS + maxItems: 1 + + clocks: + minItems: 1 + maxItems: 4 + items: + - description: Controller clock used by normal mode + - description: Reference clock used by low power mode etc + - description: Mcu bus clock for register access + - description: DMA bus clock for data transfer + + clock-names: + minItems: 1 + maxItems: 4 + items: + - const: sys_ck #required, the following ones are optional + - const: ref_ck + - const: mcu_ck + - const: dma_ck + + phys: + $ref: /schemas/types.yaml#/definitions/phandle-array + description: List of all the USB PHYs used + + vusb33-supply: + description: Regulator of USB AVDD3.3v + + vbus-supply: + $ref: /connector/usb-connector.yaml# + deprecated: true + description: | + Regulator of USB VBUS5v, needed when supports dual-role mode. + Particularly, if use an output GPIO to control a VBUS regulator, should + model it as a regulator. See bindings/regulator/fixed-regulator.yaml + It's considered valid for compatibility reasons, not allowed for + new bindings, and put into a usb-connector node. + + dr_mode: + description: See usb/generic.txt + enum: [host, peripheral, otg] + default: otg + + maximum-speed: + description: See usb/generic.txt + enum: [super-speed-plus, super-speed, high-speed, full-speed] + + "#address-cells": + enum: [1, 2] + + "#size-cells": + enum: [1, 2] + + ranges: true + + pinctrl-0: + description: A phandle to the default pinctrl state + + pinctrl-names: + description: Usually it's needed when use IDDIG/VBUS pin. + See pinctrl/pinctrl-bindings.txt + const: default + + extcon: + deprecated: true + description: | + Phandle to the extcon device detecting the IDDIG/VBUS state, neede + when supports dual-role mode. + It's considered valid for compatibility reasons, not allowed for + new bindings, and use "usb-role-switch" property instead. + + usb-role-switch: + $ref: /schemas/types.yaml#/definitions/flag + description: Support role switch. See usb/generic.txt + type: boolean + + connector: + $ref: /connector/usb-connector.yaml# + description: + Connector for dual role switch, especially for "gpio-usb-b-connector" + type: object + + port: + description: | + Any connector to the data bus of this controller should be modelled + using the OF graph bindings specified, if the "usb-role-switch" + property is used. See graph.txt + type: object + + enable-manual-drd: + $ref: /schemas/types.yaml#/definitions/flag + description: | + supports manual dual-role switch via debugfs; usually used when + receptacle is TYPE-A and also wants to support dual-role mode. + type: boolean + + wakeup-source: + description: enable USB remote wakeup, see power/wakeup-source.txt + type: boolean + + mediatek,syscon-wakeup: + $ref: /schemas/types.yaml#/definitions/phandle-array + maxItems: 1 + description: | + A phandle to syscon used to access the register of the USB wakeup glue + layer between xHCI and SPM, the field should always be a multiple of + 3 cells long. + + items: + - description: + The first cell represents a phandle to syscon + - description: + The second cell represents the register base address of the glue + layer in syscon + - description: + The third cell represents the hardware version of the glue layer, + 1 is used by mt8173 etc, 2 is used by mt2712 etc + enum: [1, 2] + + mediatek,u3p-dis-msk: + $ref: /schemas/types.yaml#/definitions/uint32 + description: The mask to disable u3ports, bit0 for u3port0, + bit1 for u3port1, ... etc + +# Required child node when support dual-role +patternProperties: + "^usb@[0-9a-f]+$": + type: object + $ref: /usb/mediatek,mtk-xhci.yaml# + description: | + The xhci should be added as subnode to mtu3 as shown in the following + example if the host mode is enabled. + +dependencies: + connector: [ 'usb-role-switch' ] + port: [ 'usb-role-switch' ] + wakeup-source: [ 'mediatek,syscon-wakeup' ] + +required: + - compatible + - reg + - reg-names + - interrupts + - clocks + - clock-names + - phys + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/mt8173-clk.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/phy/phy.h> + #include <dt-bindings/power/mt8173-power.h> + + ssusb: usb@11271000 { + compatible = "mediatek,mt8173-mtu3", "mediatek,mtu3"; + reg = <0x11271000 0x3000>, <0x11280700 0x0100>; + reg-names = "mac", "ippc"; + interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_LOW>; + phys = <&phy_port0 PHY_TYPE_USB3>, <&phy_port1 PHY_TYPE_USB2>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; + clocks = <&topckgen CLK_TOP_USB30_SEL>; + clock-names = "sys_ck"; + vusb33-supply = <&mt6397_vusb_reg>; + vbus-supply = <&usb_p0_vbus>; + extcon = <&extcon_usb>; + dr_mode = "otg"; + wakeup-source; + mediatek,syscon-wakeup = <&pericfg 0x400 1>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + xhci: usb@11270000 { + compatible = "mediatek,mt8173-xhci", "mediatek,mtk-xhci"; + reg = <0x11270000 0x1000>; + reg-names = "mac"; + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; + clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>; + clock-names = "sys_ck", "ref_ck"; + vusb33-supply = <&mt6397_vusb_reg>; + }; + }; +...