Existing HPD enablement logic is not compatible with ADV7535 bridge, thus any runtime plug-in of HDMI cable is not working on these bridge designs.
Unlike other ADV7511 family of bridges, the ADV7535 require HPD_OVERRIDE bit to set and reset for proper handling of HPD functionality.
Fix it.
Fixes: 8501fe4b14a3 ("drm: bridge: adv7511: Add support for ADV7535") Signed-off-by: Jagan Teki jagan@amarulasolutions.com --- drivers/gpu/drm/bridge/adv7511/adv7511.h | 1 + drivers/gpu/drm/bridge/adv7511/adv7511_drv.c | 29 +++++++++++++++----- 2 files changed, 23 insertions(+), 7 deletions(-)
diff --git a/drivers/gpu/drm/bridge/adv7511/adv7511.h b/drivers/gpu/drm/bridge/adv7511/adv7511.h index 592ecfcf00ca..6a882891d91c 100644 --- a/drivers/gpu/drm/bridge/adv7511/adv7511.h +++ b/drivers/gpu/drm/bridge/adv7511/adv7511.h @@ -169,6 +169,7 @@ #define ADV7511_PACKET_ENABLE_SPARE2 BIT(1) #define ADV7511_PACKET_ENABLE_SPARE1 BIT(0)
+#define ADV7535_REG_POWER2_HPD_OVERRIDE BIT(6) #define ADV7511_REG_POWER2_HPD_SRC_MASK 0xc0 #define ADV7511_REG_POWER2_HPD_SRC_BOTH 0x00 #define ADV7511_REG_POWER2_HPD_SRC_HPD 0x40 diff --git a/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c b/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c index f8e5da148599..77118c3395bf 100644 --- a/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c +++ b/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c @@ -351,11 +351,17 @@ static void __adv7511_power_on(struct adv7511 *adv7511) * from standby or are enabled. When the HPD goes low the adv7511 is * reset and the outputs are disabled which might cause the monitor to * go to standby again. To avoid this we ignore the HPD pin for the - * first few seconds after enabling the output. + * first few seconds after enabling the output. On the other hand + * adv7535 require to enable HPD Override bit for proper HPD. */ - regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2, - ADV7511_REG_POWER2_HPD_SRC_MASK, - ADV7511_REG_POWER2_HPD_SRC_NONE); + if (adv7511->type == ADV7535) + regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2, + ADV7535_REG_POWER2_HPD_OVERRIDE, + ADV7535_REG_POWER2_HPD_OVERRIDE); + else + regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2, + ADV7511_REG_POWER2_HPD_SRC_MASK, + ADV7511_REG_POWER2_HPD_SRC_NONE); }
static void adv7511_power_on(struct adv7511 *adv7511) @@ -375,6 +381,10 @@ static void adv7511_power_on(struct adv7511 *adv7511) static void __adv7511_power_off(struct adv7511 *adv7511) { /* TODO: setup additional power down modes */ + if (adv7511->type == ADV7535) + regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2, + ADV7535_REG_POWER2_HPD_OVERRIDE, 0); + regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER, ADV7511_POWER_POWER_DOWN, ADV7511_POWER_POWER_DOWN); @@ -672,9 +682,14 @@ adv7511_detect(struct adv7511 *adv7511, struct drm_connector *connector) status = connector_status_disconnected; } else { /* Renable HPD sensing */ - regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2, - ADV7511_REG_POWER2_HPD_SRC_MASK, - ADV7511_REG_POWER2_HPD_SRC_BOTH); + if (adv7511->type == ADV7535) + regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2, + ADV7535_REG_POWER2_HPD_OVERRIDE, + ADV7535_REG_POWER2_HPD_OVERRIDE); + else + regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2, + ADV7511_REG_POWER2_HPD_SRC_MASK, + ADV7511_REG_POWER2_HPD_SRC_BOTH); }
adv7511->status = status;