This patch is _only_ code motion to prepare for the patch ("drm/bridge: ti-sn65dsi86: Properly get the EDID, but only if refclk") and make it easier to understand.
Signed-off-by: Douglas Anderson dianders@chromium.org ---
drivers/gpu/drm/bridge/ti-sn65dsi86.c | 196 +++++++++++++------------- 1 file changed, 98 insertions(+), 98 deletions(-)
diff --git a/drivers/gpu/drm/bridge/ti-sn65dsi86.c b/drivers/gpu/drm/bridge/ti-sn65dsi86.c index 942019842ff4..491c9c4f32d1 100644 --- a/drivers/gpu/drm/bridge/ti-sn65dsi86.c +++ b/drivers/gpu/drm/bridge/ti-sn65dsi86.c @@ -345,6 +345,104 @@ static int ti_sn_bridge_parse_regulators(struct ti_sn_bridge *pdata) pdata->supplies); }
+static u32 ti_sn_bridge_get_dsi_freq(struct ti_sn_bridge *pdata) +{ + u32 bit_rate_khz, clk_freq_khz; + struct drm_display_mode *mode = + &pdata->bridge.encoder->crtc->state->adjusted_mode; + + bit_rate_khz = mode->clock * + mipi_dsi_pixel_format_to_bpp(pdata->dsi->format); + clk_freq_khz = bit_rate_khz / (pdata->dsi->lanes * 2); + + return clk_freq_khz; +} + +/* clk frequencies supported by bridge in Hz in case derived from REFCLK pin */ +static const u32 ti_sn_bridge_refclk_lut[] = { + 12000000, + 19200000, + 26000000, + 27000000, + 38400000, +}; + +/* clk frequencies supported by bridge in Hz in case derived from DACP/N pin */ +static const u32 ti_sn_bridge_dsiclk_lut[] = { + 468000000, + 384000000, + 416000000, + 486000000, + 460800000, +}; + +static void ti_sn_bridge_set_refclk_freq(struct ti_sn_bridge *pdata) +{ + int i; + u32 refclk_rate; + const u32 *refclk_lut; + size_t refclk_lut_size; + + if (pdata->refclk) { + refclk_rate = clk_get_rate(pdata->refclk); + refclk_lut = ti_sn_bridge_refclk_lut; + refclk_lut_size = ARRAY_SIZE(ti_sn_bridge_refclk_lut); + clk_prepare_enable(pdata->refclk); + } else { + refclk_rate = ti_sn_bridge_get_dsi_freq(pdata) * 1000; + refclk_lut = ti_sn_bridge_dsiclk_lut; + refclk_lut_size = ARRAY_SIZE(ti_sn_bridge_dsiclk_lut); + } + + /* for i equals to refclk_lut_size means default frequency */ + for (i = 0; i < refclk_lut_size; i++) + if (refclk_lut[i] == refclk_rate) + break; + + regmap_update_bits(pdata->regmap, SN_DPPLL_SRC_REG, REFCLK_FREQ_MASK, + REFCLK_FREQ(i)); +} + +static void ti_sn_bridge_post_disable(struct drm_bridge *bridge) +{ + struct ti_sn_bridge *pdata = bridge_to_ti_sn_bridge(bridge); + + clk_disable_unprepare(pdata->refclk); + + pm_runtime_put_sync(pdata->dev); +} + +static void ti_sn_bridge_pre_enable(struct drm_bridge *bridge) +{ + struct ti_sn_bridge *pdata = bridge_to_ti_sn_bridge(bridge); + + pm_runtime_get_sync(pdata->dev); + + /* configure bridge ref_clk */ + ti_sn_bridge_set_refclk_freq(pdata); + + /* + * HPD on this bridge chip is a bit useless. This is an eDP bridge + * so the HPD is an internal signal that's only there to signal that + * the panel is done powering up. ...but the bridge chip debounces + * this signal by between 100 ms and 400 ms (depending on process, + * voltage, and temperate--I measured it at about 200 ms). One + * particular panel asserted HPD 84 ms after it was powered on meaning + * that we saw HPD 284 ms after power on. ...but the same panel said + * that instead of looking at HPD you could just hardcode a delay of + * 200 ms. We'll assume that the panel driver will have the hardcoded + * delay in its prepare and always disable HPD. + * + * If HPD somehow makes sense on some future panel we'll have to + * change this to be conditional on someone specifying that HPD should + * be used. + */ + regmap_update_bits(pdata->regmap, SN_HPD_DISABLE_REG, HPD_DISABLE, + HPD_DISABLE); + + drm_panel_prepare(pdata->panel); +} + static int ti_sn_bridge_attach(struct drm_bridge *bridge, enum drm_bridge_attach_flags flags) { @@ -443,64 +541,6 @@ static void ti_sn_bridge_disable(struct drm_bridge *bridge) drm_panel_unprepare(pdata->panel); }
-static u32 ti_sn_bridge_get_dsi_freq(struct ti_sn_bridge *pdata) -{ - u32 bit_rate_khz, clk_freq_khz; - struct drm_display_mode *mode = - &pdata->bridge.encoder->crtc->state->adjusted_mode; - - bit_rate_khz = mode->clock * - mipi_dsi_pixel_format_to_bpp(pdata->dsi->format); - clk_freq_khz = bit_rate_khz / (pdata->dsi->lanes * 2); - - return clk_freq_khz; -} - -/* clk frequencies supported by bridge in Hz in case derived from REFCLK pin */ -static const u32 ti_sn_bridge_refclk_lut[] = { - 12000000, - 19200000, - 26000000, - 27000000, - 38400000, -}; - -/* clk frequencies supported by bridge in Hz in case derived from DACP/N pin */ -static const u32 ti_sn_bridge_dsiclk_lut[] = { - 468000000, - 384000000, - 416000000, - 486000000, - 460800000, -}; - -static void ti_sn_bridge_set_refclk_freq(struct ti_sn_bridge *pdata) -{ - int i; - u32 refclk_rate; - const u32 *refclk_lut; - size_t refclk_lut_size; - - if (pdata->refclk) { - refclk_rate = clk_get_rate(pdata->refclk); - refclk_lut = ti_sn_bridge_refclk_lut; - refclk_lut_size = ARRAY_SIZE(ti_sn_bridge_refclk_lut); - clk_prepare_enable(pdata->refclk); - } else { - refclk_rate = ti_sn_bridge_get_dsi_freq(pdata) * 1000; - refclk_lut = ti_sn_bridge_dsiclk_lut; - refclk_lut_size = ARRAY_SIZE(ti_sn_bridge_dsiclk_lut); - } - - /* for i equals to refclk_lut_size means default frequency */ - for (i = 0; i < refclk_lut_size; i++) - if (refclk_lut[i] == refclk_rate) - break; - - regmap_update_bits(pdata->regmap, SN_DPPLL_SRC_REG, REFCLK_FREQ_MASK, - REFCLK_FREQ(i)); -} - static void ti_sn_bridge_set_dsi_rate(struct ti_sn_bridge *pdata) { unsigned int bit_rate_mhz, clk_freq_mhz; @@ -821,46 +861,6 @@ static void ti_sn_bridge_enable(struct drm_bridge *bridge) drm_panel_enable(pdata->panel); }
-static void ti_sn_bridge_pre_enable(struct drm_bridge *bridge) -{ - struct ti_sn_bridge *pdata = bridge_to_ti_sn_bridge(bridge); - - pm_runtime_get_sync(pdata->dev); - - /* configure bridge ref_clk */ - ti_sn_bridge_set_refclk_freq(pdata); - - /* - * HPD on this bridge chip is a bit useless. This is an eDP bridge - * so the HPD is an internal signal that's only there to signal that - * the panel is done powering up. ...but the bridge chip debounces - * this signal by between 100 ms and 400 ms (depending on process, - * voltage, and temperate--I measured it at about 200 ms). One - * particular panel asserted HPD 84 ms after it was powered on meaning - * that we saw HPD 284 ms after power on. ...but the same panel said - * that instead of looking at HPD you could just hardcode a delay of - * 200 ms. We'll assume that the panel driver will have the hardcoded - * delay in its prepare and always disable HPD. - * - * If HPD somehow makes sense on some future panel we'll have to - * change this to be conditional on someone specifying that HPD should - * be used. - */ - regmap_update_bits(pdata->regmap, SN_HPD_DISABLE_REG, HPD_DISABLE, - HPD_DISABLE); - - drm_panel_prepare(pdata->panel); -} - -static void ti_sn_bridge_post_disable(struct drm_bridge *bridge) -{ - struct ti_sn_bridge *pdata = bridge_to_ti_sn_bridge(bridge); - - clk_disable_unprepare(pdata->refclk); - - pm_runtime_put_sync(pdata->dev); -} - static const struct drm_bridge_funcs ti_sn_bridge_funcs = { .attach = ti_sn_bridge_attach, .pre_enable = ti_sn_bridge_pre_enable,