During a hotplug cycle (such as a TV going out of suspend, or when the cable is disconnected and reconnected), the expectation is that the same state used before the disconnection is reused until the next commit.
However, the HDMI scrambling requires that some flags are set in the monitor, and those flags are very likely to be reset when the cable has been disconnected. This will thus result in a blank display, even if the display pipeline configuration hasn't been modified or is in the exact same state.
One solution would be to enable the scrambling-related bits again on reconnection, but the HDMI 2.0 specification (Section 6.1.3.1 - Scrambling Control) requires that the scrambling enable bit is set before sending any scrambled video signal. Using that solution would break that specification expectation.
Thus, we need to do a full modeset on the connector so that we disable the video signal, enable the scrambling bit, and enable the video signal again.
The i915 code was doing this already, so let's take its code and convert it into a generic helper.
Signed-off-by: Maxime Ripard maxime@cerno.tech --- drivers/gpu/drm/drm_atomic_helper.c | 109 ++++++++++++++++++++++++++++ include/drm/drm_atomic_helper.h | 3 + 2 files changed, 112 insertions(+)
diff --git a/drivers/gpu/drm/drm_atomic_helper.c b/drivers/gpu/drm/drm_atomic_helper.c index 2c0c6ec92820..9f3fcc65e66e 100644 --- a/drivers/gpu/drm/drm_atomic_helper.c +++ b/drivers/gpu/drm/drm_atomic_helper.c @@ -38,6 +38,7 @@ #include <drm/drm_gem_atomic_helper.h> #include <drm/drm_plane_helper.h> #include <drm/drm_print.h> +#include <drm/drm_scdc_helper.h> #include <drm/drm_self_refresh_helper.h> #include <drm/drm_vblank.h> #include <drm/drm_writeback.h> @@ -3524,3 +3525,111 @@ drm_atomic_helper_bridge_propagate_bus_fmt(struct drm_bridge *bridge, return input_fmts; } EXPORT_SYMBOL(drm_atomic_helper_bridge_propagate_bus_fmt); + +static int modeset_pipe(struct drm_crtc *crtc, + struct drm_modeset_acquire_ctx *ctx) +{ + struct drm_atomic_state *state; + struct drm_crtc_state *crtc_state; + int ret; + + state = drm_atomic_state_alloc(crtc->dev); + if (!state) + return -ENOMEM; + + state->acquire_ctx = ctx; + + crtc_state = drm_atomic_get_crtc_state(state, crtc); + if (IS_ERR(crtc_state)) { + ret = PTR_ERR(crtc_state); + goto out; + } + + crtc_state->connectors_changed = true; + + ret = drm_atomic_commit(state); +out: + drm_atomic_state_put(state); + + return ret; +} + +/** + * drm_atomic_helper_connector_hdmi_reset_link() - Resets an HDMI link + * @connector: DRM connector we want to reset + * @ctx: Lock acquisition context + * + * This helper is here to restore the HDMI link state after the + * connector status has changed, typically when a TV has come out of + * suspend or when the HDMI cable has been disconnected and then + * reconnected. + * + * Returns: + * 0 on success, a negative error code otherwise. + */ +int drm_atomic_helper_connector_hdmi_reset_link(struct drm_connector *connector, + struct drm_modeset_acquire_ctx *ctx) +{ + struct drm_device *drm = connector->dev; + struct drm_connector_state *conn_state; + struct drm_crtc_state *crtc_state; + struct drm_crtc *crtc; + u8 config; + int ret; + + if (!connector) + return 0; + + drm_WARN_ON(drm, + (connector->connector_type != DRM_MODE_CONNECTOR_HDMIA) && + (connector->connector_type != DRM_MODE_CONNECTOR_HDMIB)); + + ret = drm_modeset_lock(&drm->mode_config.connection_mutex, ctx); + if (ret) + return ret; + + conn_state = connector->state; + crtc = conn_state->crtc; + if (!crtc) + return 0; + + ret = drm_modeset_lock(&crtc->mutex, ctx); + if (ret) + return ret; + + crtc_state = crtc->state; + if (!crtc_state->active) + return 0; + + if (!conn_state->hdmi_needs_high_tmds_ratio && + !conn_state->hdmi_needs_scrambling) + return 0; + + if (conn_state->commit && + !try_wait_for_completion(&conn_state->commit->hw_done)) + return 0; + + ret = drm_scdc_readb(connector->ddc, SCDC_TMDS_CONFIG, &config); + if (ret < 0) { + drm_err(drm, "Failed to read TMDS config: %d\n", ret); + return 0; + } + + if (!!(config & SCDC_TMDS_BIT_CLOCK_RATIO_BY_40) == + conn_state->hdmi_needs_high_tmds_ratio && + !!(config & SCDC_SCRAMBLING_ENABLE) == + conn_state->hdmi_needs_scrambling) + return 0; + + /* + * HDMI 2.0 says that one should not send scrambled data + * prior to configuring the sink scrambling, and that + * TMDS clock/data transmission should be suspended when + * changing the TMDS clock rate in the sink. So let's + * just do a full modeset here, even though some sinks + * would be perfectly happy if were to just reconfigure + * the SCDC settings on the fly. + */ + return modeset_pipe(crtc, ctx); +} +EXPORT_SYMBOL(drm_atomic_helper_connector_hdmi_reset_link); diff --git a/include/drm/drm_atomic_helper.h b/include/drm/drm_atomic_helper.h index 4045e2507e11..d7727f9a6fe9 100644 --- a/include/drm/drm_atomic_helper.h +++ b/include/drm/drm_atomic_helper.h @@ -231,4 +231,7 @@ drm_atomic_helper_bridge_propagate_bus_fmt(struct drm_bridge *bridge, u32 output_fmt, unsigned int *num_input_fmts);
+int drm_atomic_helper_connector_hdmi_reset_link(struct drm_connector *connector, + struct drm_modeset_acquire_ctx *ctx); + #endif /* DRM_ATOMIC_HELPER_H_ */