Hi everyone,
Here's a (pretty long) series to introduce support in the VC4 DRM driver for the display pipeline found in the BCM2711 (and thus the RaspberryPi 4).
The main differences are that there's two HDMI controllers and that there's more pixelvalve now. Those pixelvalve come with a mux in the HVS that still have only 3 FIFOs. Both of those differences are breaking a bunch of expectations in the driver, so we first need a good bunch of cleanup and reworks to introduce support for the new controllers.
Similarly, the HDMI controller has all its registers shuffled and split in multiple controllers now, so we need a bunch of changes to support this as well.
Only the HDMI support is enabled for now (even though the DPI and DSI outputs have been tested too).
Let me know if you have any comments Maxime
Cc: bcm-kernel-feedback-list@broadcom.com Cc: devicetree@vger.kernel.org Cc: Kamal Dasu kdasu.kdev@gmail.com Cc: Philipp Zabel p.zabel@pengutronix.de Cc: Rob Herring robh+dt@kernel.org Cc: Stephen Boyd sboyd@kernel.org
Changes from v4: - Rebased on top of next-20200828 - Collected the various tags - Fixed some issues with 4k support and dual output (thanks Hoegeun!) - Fixed typos in commit logs (thanks Dave!) - Split the csc setup hook into its own patch again - Added the CEC clock to the DT binding - Fixed the DT binding example - Reduced the number of calls to of_device_is_compatible in vc4_kms_load - Added back the check for the state commit in our commit hook
Changes from v3: - Rebased on top of next-20200708 - Added a name to the HDMI audio codec component - Only disable the BCM2711 HDMI pixelvalves at boot - Fixed an error in the HVS binding - Fix a framebuffer size condition that was inverted - Changed the channel allocation algorithm using Eric's suggestion - Always write the muxing values instead of updating if needed - Improved a bit the hvs_available_channels comment in the structure - Change atomic_complete_commit code to use for_each_new_crtc_in_state - Change the muxing code to take into account disparities between the BCM2711 and previous SoCs. - Only change the clock rate on BCM2711 during a modeset - Fix a crash at atomic_disable - Use clk_set_min_rate for the core clock too - Add a few defines, and simplify the FIFO level stuff - Reordered the patches according to Eric's reviews - Fixed a regression with VID_CTL setting on RPI3
Changes from v2: - Rebased on top of next-20200526 - Split the firmware clock series away - Removed the stuck pixel (with all the subsequent pixels being shifted by one - Fixed the writeback issue too. - Fix the dual output - Fixed the return value of phy_get_cp_current - Enhanced the comment on the reset delay - Increase the max width and height - Made a proper Kconfig option for the DVP clock driver - Fixed the alsa card name collision
Changes from v1: - Rebased on top of 5.7-rc1 - Run checkpatch - Added audio support - Fixed some HDMI timeouts - Swiched to clk_hw_register_gate_parent_data - Reorder Kconfig symbols in drivers/i2c/busses - Make the firmware clocks a child of the firmware node - Switch DVP clock driver to clk_hw interface - constify raspberrypi_clk_data in raspberrypi_clock_property - Don't mark firmware clocks as IGNORE_UNUSED - Change from reset_ms to reset_us in reset-simple, and add a bit more comments - Remove generic clk patch to test if a NULL pointer is returned - Removed misleading message in the is_prepared renaming patch commit message - Constify HDMI controller variants - Fix a bug in the allocation size of the clk data array - Added a mention in the DT binding conversion patches about the breakage - Merged a few fixes from kbuild - Fixed a few bisection and CEC build issues - Collected Acked-by and Reviewed-by - Change Dave email address to raspberrypi.com
Dave Stevenson (7): drm/vc4: Add support for the BCM2711 HVS5 drm/vc4: plane: Change LBM alignment constraint on LBM drm/vc4: plane: Optimize the LBM allocation size drm/vc4: hdmi: Use reg-names to retrieve the HDMI audio registers drm/vc4: hdmi: Reset audio infoframe on encoder_enable if previously streaming drm/vc4: hdmi: Set the b-frame marker to the match ALSA's default. drm/vc4: hdmi: Add audio-related callbacks
Hoegeun Kwon (1): drm/vc4: hdmi: Add pixel BVB clock control
Maxime Ripard (72): dt-bindings: display: Add support for the BCM2711 HVS drm/vc4: hvs: Boost the core clock during modeset drm/vc4: plane: Create more planes drm/vc4: crtc: Deal with different number of pixel per clock drm/vc4: crtc: Use a shared interrupt drm/vc4: crtc: Move the cob allocation outside of bind drm/vc4: crtc: Rename HVS channel to output drm/vc4: crtc: Use local chan variable drm/vc4: crtc: Enable and disable the PV in atomic_enable / disable drm/vc4: kms: Convert to for_each_new_crtc_state drm/vc4: crtc: Assign output to channel automatically drm/vc4: crtc: Add FIFO depth to vc4_crtc_data drm/vc4: crtc: Add function to compute FIFO level bits drm/vc4: crtc: Rename HDMI encoder type to HDMI0 drm/vc4: crtc: Add HDMI1 encoder type drm/vc4: crtc: Disable color management for HVS5 drm/vc4: crtc: Turn pixelvalve reset into a function drm/vc4: crtc: Move PV dump to config_pv drm/vc4: crtc: Move HVS init and close to a function drm/vc4: crtc: Move the HVS gamma LUT setup to our init function drm/vc4: hvs: Make sure our channel is reset drm/vc4: crtc: Remove mode_set_nofb drm/vc4: crtc: Remove redundant pixelvalve reset drm/vc4: crtc: Move HVS channel init before the PV initialisation drm/vc4: encoder: Add finer-grained encoder callbacks drm/vc4: crtc: Add a delay after disabling the PixelValve output drm/vc4: crtc: Clear the PixelValve FIFO on disable drm/vc4: crtc: Clear the PixelValve FIFO during configuration drm/vc4: hvs: Make the stop_channel function public drm/vc4: hvs: Introduce a function to get the assigned FIFO drm/vc4: crtc: Move the CRTC disable out drm/vc4: drv: Disable the CRTC at boot time dt-bindings: display: vc4: pv: Add BCM2711 pixel valves drm/vc4: crtc: Add BCM2711 pixelvalves drm/vc4: hdmi: Use debugfs private field drm/vc4: hdmi: Move structure to header drm/vc4: hdmi: rework connectors and encoders drm/vc4: hdmi: Remove DDC argument to connector_init drm/vc4: hdmi: Rename hdmi to vc4_hdmi drm/vc4: hdmi: Move accessors to vc4_hdmi drm/vc4: hdmi: Use local vc4_hdmi directly drm/vc4: hdmi: Add container_of macros for encoders and connectors drm/vc4: hdmi: Pass vc4_hdmi to CEC code drm/vc4: hdmi: Retrieve the vc4_hdmi at unbind using our device drm/vc4: hdmi: Remove vc4_dev hdmi pointer drm/vc4: hdmi: Remove vc4_hdmi_connector drm/vc4: hdmi: Introduce resource init and variant drm/vc4: hdmi: Implement a register layout abstraction drm/vc4: hdmi: Add reset callback drm/vc4: hdmi: Add PHY init and disable function drm/vc4: hdmi: Add PHY RNG enable / disable function drm/vc4: hdmi: Add a CSC setup callback drm/vc4: hdmi: Add a set_timings callback drm/vc4: hdmi: Store the encoder type in the variant structure drm/vc4: hdmi: Deal with multiple debugfs files drm/vc4: hdmi: Move CEC init to its own function drm/vc4: hdmi: Add CEC support flag drm/vc4: hdmi: Remove unused CEC_CLOCK_DIV define drm/vc4: hdmi: Rename drm_encoder pointer in mode_valid drm/vc4: hdmi: Adjust HSM clock rate depending on pixel rate drm/vc4: hdmi: Use clk_set_min_rate instead drm/vc4: hdmi: Deal with multiple ALSA cards drm/vc4: hdmi: Remove register dumps in enable drm/vc4: hdmi: Always recenter the HDMI FIFO drm/vc4: hdmi: Implement finer-grained hooks drm/vc4: hdmi: Do the VID_CTL configuration at once drm/vc4: hdmi: Switch to blank pixels when disabled drm/vc4: hdmi: Support the BCM2711 HDMI controllers dt-bindings: display: vc4: hdmi: Add BCM2711 HDMI controllers bindings dt-bindings: display: vc4: Document BCM2711 VC5 drm/vc4: drv: Support BCM2711 ARM: dts: bcm2711: Enable the display pipeline
Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml | 117 +++++- Documentation/devicetree/bindings/display/brcm,bcm2835-hvs.yaml | 18 +- Documentation/devicetree/bindings/display/brcm,bcm2835-pixelvalve0.yaml | 5 +- Documentation/devicetree/bindings/display/brcm,bcm2835-vc4.yaml | 1 +- arch/arm/boot/dts/bcm2711-rpi-4-b.dts | 48 ++- arch/arm/boot/dts/bcm2711.dtsi | 122 ++++- drivers/gpu/drm/vc4/Makefile | 1 +- drivers/gpu/drm/vc4/vc4_crtc.c | 354 +++++++++++---- drivers/gpu/drm/vc4/vc4_drv.c | 5 +- drivers/gpu/drm/vc4/vc4_drv.h | 43 +- drivers/gpu/drm/vc4/vc4_hdmi.c | 1650 +++++++++++++++++++++++++++++++++++++++++++----------------------------- drivers/gpu/drm/vc4/vc4_hdmi.h | 184 ++++++++- drivers/gpu/drm/vc4/vc4_hdmi_phy.c | 520 +++++++++++++++++++++++- drivers/gpu/drm/vc4/vc4_hdmi_regs.h | 442 +++++++++++++++++++- drivers/gpu/drm/vc4/vc4_hvs.c | 269 +++++++----- drivers/gpu/drm/vc4/vc4_kms.c | 229 +++++++++- drivers/gpu/drm/vc4/vc4_plane.c | 222 +++++++--- drivers/gpu/drm/vc4/vc4_regs.h | 177 +++----- drivers/gpu/drm/vc4/vc4_txp.c | 4 +- 19 files changed, 3406 insertions(+), 1005 deletions(-) create mode 100644 Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml create mode 100644 drivers/gpu/drm/vc4/vc4_hdmi.h create mode 100644 drivers/gpu/drm/vc4/vc4_hdmi_phy.c create mode 100644 drivers/gpu/drm/vc4/vc4_hdmi_regs.h
base-commit: 20c0f70ad7bf5aaf2e22ef974867d0708373fe93