Hi,
On 3/22/21 10:47 PM, Ville Syrjälä wrote:
On Mon, Mar 22, 2021 at 10:28:06PM +0100, Hans de Goede wrote:
Hi,
On 3/22/21 9:59 PM, Ville Syrjälä wrote:
On Mon, Mar 22, 2021 at 04:51:47PM -0400, Rodrigo Vivi wrote:
On Fri, Mar 19, 2021 at 04:45:32PM +0100, Hans de Goede wrote:
Hi,
On 3/1/21 4:43 PM, Hans de Goede wrote:
After the recently added commit fe0f1e3bfdfe ("drm/i915: Shut down displays gracefully on reboot"), the DSI panel on a Cherry Trail based Predia Basic tablet would no longer properly light up after reboot.
The backlight still turns back on after reboot, but the LCD shows an all black display. The display is also all black during the time that EFI / the GOP is managing it, so e.g. the grub menu also is not visible.
In this scenario the panel is initialized so that it appears to be working and the fastboot code skips doing a modeset. Forcing a modeset by doing a chvt to a text-console over ssh followed by echo-ing 1 and then 0 to /sys/class/graphics/fb0/blank causes the panel to work again.
Add a QUIRK_SKIP_SHUTDOWN quirk which turns i915_driver_shutdown() into a no-op when set; and set this on vlv/chv devices when a DSI panel is detected, to work around this.
Admittedly this is a bit of a big hammer, but these platforms have been around for quite some time now and they have always worked fine without the new behavior to shutdown everything on shutdown/reboot. This approach simply disables the recently introduced new shutdown behavior in this specific case where it is known to cause problems. Which is a nice and simple way to deal with this.
Signed-off-by: Hans de Goede hdegoede@redhat.com
Ping? Since sending this patch I've been seeing the issue addressed by this on variour other CHT based devices too.
So we have various devices suffering from a black screen after reboot now. This is pretty serious usability regression.
As such it would be good to get this reviewed, or another fix proposed.
For the quirks we try to limit them to very specific vendor and model ids, so I wonder if it would be possible to get this information in here instead to all the vlv with dsi...
Or avoid the quirk "infra" and skip to all vlv with active dsi?!
Jani? Ville?
We need to figure out why the panel doesn't start up again.
Note it is the GOP which fails to light it up again. I think we turn something off, which after a power-on-reset is on, so the GOP expects it to be on.
Hmm. Do any of the reboot=warm|cold|whatever knobs make a difference? Are there any fast vs. slow boot settings in the BIOS setup?
Ok, so I was running the tests which you requested and during this I managed to find the real problem.
What happens on reboot is a really quick panel off/on cycle and that is causing the issue.
I can reproduce this by doing:
chvt 3; echo 1 > /sys/class/graphics/fb0/blank; echo 0 > /sys/class/graphics/fb0/blank
The problem is that we're not honoring panel_pwr_cycle_delay because intel_dsi_msleep() is a no-op on devices with a MIPI-sequences version >= 3, because those sequences already contain the necessary delays, at least for most of the steps during the on/off sequences. It seems that the pwr-cycle delay is not handled by those v3+ sequences.
So fixing this is as simple as switching to a regular msleep for the intel_dsi->panel_pwr_cycle_delay.
Once we do that it would be good (for e.g. suspend/resume speed) to fix:
/* * FIXME As we do with eDP, just make a note of the time here * and perform the wait before the next panel power on. */
Which sits right above that msleep. Since I have a reproducer now which shows when the sleep is too short, it should now be easy ti fix the FIXME and test that the fix works. I'll do this in a separate patch and send a patch-set with both patches replacing this patch.
Regards,
Hans