On Sun, Jun 21, 2020 at 12:30:10AM +0200, Ondřej Jirman wrote:
On Sat, Jun 20, 2020 at 11:25:29PM +0200, Sam Ravnborg wrote:
Hi Ondrej et al.
On Wed, Jun 17, 2020 at 02:32:07AM +0200, Ondrej Jirman wrote:
From: Icenowy Zheng icenowy@aosc.io
Xingbangda XBD599 is a 5.99" 720x1440 MIPI-DSI IPS LCD panel made by Xingbangda, which is used on PinePhone final assembled phones.
It is based on Sitronix ST7703 LCD controller.
I am a little late to the game here - so sorry if this has been discussed before. We already have panel-rocktech-jh057n00900.c which is a panle driver based on st7703. Why is it we need a new driver?
No reason other than the driver not being named after the controller, so I didn't notice.
Would it not be better to have one st7703 driver that suipports both panels?
The driver would need dedicated init functions depending on the panel. But a lot could also be shared.
I guess I can move the code there.
In the same process the river should then be renamed to follow other sitronix based drivers. So the next developer will recognize this and use the correct driver.
Sam
regards, o.
Sam
Add support for it.
Signed-off-by: Icenowy Zheng icenowy@aosc.io Signed-off-by: Ondrej Jirman megous@megous.com
drivers/gpu/drm/panel/Kconfig | 10 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-sitronix-st7703.c | 535 ++++++++++++++++++ 3 files changed, 546 insertions(+) create mode 100644 drivers/gpu/drm/panel/panel-sitronix-st7703.c
diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig index 39055c1f0e2f..b7bc157b0612 100644 --- a/drivers/gpu/drm/panel/Kconfig +++ b/drivers/gpu/drm/panel/Kconfig @@ -395,6 +395,16 @@ config DRM_PANEL_SITRONIX_ST7701 ST7701 controller for 480X864 LCD panels with MIPI/RGB/SPI system interfaces.
+config DRM_PANEL_SITRONIX_ST7703
- tristate "Sitronix ST7703 panel driver"
- depends on OF
- depends on DRM_MIPI_DSI
- depends on BACKLIGHT_CLASS_DEVICE
- help
Say Y here if you want to enable support for the SitronixST7703 controller for 720X1440 LCD panels with MIPI/RGB/SPIsystem interfaces.config DRM_PANEL_SITRONIX_ST7789V tristate "Sitronix ST7789V panel" depends on OF && SPI diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile index de74f282c433..47f4789a8685 100644 --- a/drivers/gpu/drm/panel/Makefile +++ b/drivers/gpu/drm/panel/Makefile @@ -41,6 +41,7 @@ obj-$(CONFIG_DRM_PANEL_SHARP_LQ101R1SX01) += panel-sharp-lq101r1sx01.o obj-$(CONFIG_DRM_PANEL_SHARP_LS037V7DW01) += panel-sharp-ls037v7dw01.o obj-$(CONFIG_DRM_PANEL_SHARP_LS043T1LE01) += panel-sharp-ls043t1le01.o obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7701) += panel-sitronix-st7701.o +obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7703) += panel-sitronix-st7703.o obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7789V) += panel-sitronix-st7789v.o obj-$(CONFIG_DRM_PANEL_SONY_ACX424AKP) += panel-sony-acx424akp.o obj-$(CONFIG_DRM_PANEL_SONY_ACX565AKM) += panel-sony-acx565akm.o diff --git a/drivers/gpu/drm/panel/panel-sitronix-st7703.c b/drivers/gpu/drm/panel/panel-sitronix-st7703.c new file mode 100644 index 000000000000..dbd46b6c0b46 --- /dev/null +++ b/drivers/gpu/drm/panel/panel-sitronix-st7703.c @@ -0,0 +1,535 @@ +// SPDX-License-Identifier: GPL-2.0 +/*
- DRM driver for Sitronix ST7703 MIPI DSI panel
- Copyright (C) 2020 Ondrej Jirman megous@megous.com
- Copyright (C) 2019-2020 Icenowy Zheng icenowy@aosc.io
- Based on panel-rocktech-jh057n00900.c, which is:
- Copyright (C) Purism SPC 2019
- */
+#include <linux/delay.h> +#include <linux/gpio/consumer.h> +#include <linux/mod_devicetable.h> +#include <linux/module.h> +#include <linux/of_device.h> +#include <linux/regulator/consumer.h>
+#include <drm/drm_mipi_dsi.h> +#include <drm/drm_modes.h> +#include <drm/drm_panel.h> +#include <drm/drm_print.h>
+/* Manufacturer specific DCS commands */ +#define ST7703_CMD_SETDISP 0xB2 +#define ST7703_CMD_SETRGBIF 0xB3 +#define ST7703_CMD_SETCYC 0xB4 +#define ST7703_CMD_SETBGP 0xB5 +#define ST7703_CMD_SETVCOM 0xB6 +#define ST7703_CMD_SETOTP 0xB7 +#define ST7703_CMD_SETPOWER_EXT 0xB8 +#define ST7703_CMD_SETEXTC 0xB9 +#define ST7703_CMD_SETMIPI 0xBA +#define ST7703_CMD_SETVDC 0xBC +#define ST7703_CMD_UNK_BF 0xBF +#define ST7703_CMD_SETSCR 0xC0 +#define ST7703_CMD_SETPOWER 0xC1 +#define ST7703_CMD_UNK_C6 0xC6 +#define ST7703_CMD_SETPANEL 0xCC +#define ST7703_CMD_RDID1 0xDA +#define ST7703_CMD_RDID2 0xDB +#define ST7703_CMD_RDID3 0xDC +#define ST7703_CMD_SETGAMMA 0xE0 +#define ST7703_CMD_SETEQ 0xE3 +#define ST7703_CMD_SETGIP1 0xE9 +#define ST7703_CMD_SETGIP2 0xEA
+struct st7703_panel_desc {
- const struct drm_display_mode *mode;
- unsigned int lanes;
- unsigned long flags;
- enum mipi_dsi_pixel_format format;
- const char *const *supply_names;
- unsigned int num_supplies;
+};
+struct st7703 {
- struct device *dev;
- struct drm_panel panel;
- struct gpio_desc *reset_gpio;
- struct regulator_bulk_data *supplies;
- const struct st7703_panel_desc *desc;
- bool prepared;
+};
+static inline struct st7703 *panel_to_st7703(struct drm_panel *panel) +{
- return container_of(panel, struct st7703, panel);
+}
+#define dsi_dcs_write_seq(dsi, cmd, seq...) do { \
static const u8 d[] = { seq }; \int ret; \ret = mipi_dsi_dcs_write(dsi, cmd, d, ARRAY_SIZE(d)); \if (ret < 0) \return ret; \- } while (0)
+static int st7703_init_sequence(struct st7703 *ctx) +{
- struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
- struct device *dev = ctx->dev;
- /*
* Init sequence was supplied by the panel vendor.*/- /* Magic sequence to unlock user commands below. */
- dsi_dcs_write_seq(dsi, ST7703_CMD_SETEXTC, 0xF1, 0x12, 0x83);
- dsi_dcs_write_seq(dsi, ST7703_CMD_SETMIPI,
0x33, /* VC_main = 0, Lane_Number = 3 (4 lanes) */0x81, /* DSI_LDO_SEL = 1.7V, RTERM = 90 Ohm */0x05, /* IHSRX = x6 (Low High Speed driving ability) */0xF9, /* TX_CLK_SEL = fDSICLK/16 */0x0E, /* HFP_OSC (min. HFP number in DSI mode) */0x0E, /* HBP_OSC (min. HBP number in DSI mode) *//* The rest is undocumented in ST7703 datasheet */0x20, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x44, 0x25, 0x00, 0x91, 0x0a, 0x00, 0x00, 0x02,0x4F, 0x11, 0x00, 0x00, 0x37);- dsi_dcs_write_seq(dsi, ST7703_CMD_SETPOWER_EXT,
0x25, /* PCCS = 2, ECP_DC_DIV = 1/4 HSYNC */0x22, /* DT = 15ms XDK_ECP = x2 */0x20, /* PFM_DC_DIV = /1 */0x03 /* ECP_SYNC_EN = 1, VGX_SYNC_EN = 1 */);- /* RGB I/F porch timing */
- dsi_dcs_write_seq(dsi, ST7703_CMD_SETRGBIF,
0x10, /* VBP_RGB_GEN */0x10, /* VFP_RGB_GEN */0x05, /* DE_BP_RGB_GEN */0x05, /* DE_FP_RGB_GEN *//* The rest is undocumented in ST7703 datasheet */0x03, 0xFF,0x00, 0x00,0x00, 0x00);- /* Source driving settings. */
- dsi_dcs_write_seq(dsi, ST7703_CMD_SETSCR,
0x73, /* N_POPON */0x73, /* N_NOPON */0x50, /* I_POPON */0x50, /* I_NOPON */0x00, /* SCR[31,24] */0xC0, /* SCR[23,16] */0x08, /* SCR[15,8] */0x70, /* SCR[7,0] */0x00 /* Undocumented */);- /* NVDDD_SEL = -1.8V, VDDD_SEL = out of range (possibly 1.9V?) */
- dsi_dcs_write_seq(dsi, ST7703_CMD_SETVDC, 0x4E);
- /*
* SS_PANEL = 1 (reverse scan), GS_PANEL = 0 (normal scan)* REV_PANEL = 1 (normally black panel), BGR_PANEL = 1 (BGR)*/- dsi_dcs_write_seq(dsi, ST7703_CMD_SETPANEL, 0x0B);
- /* Zig-Zag Type C column inversion. */
- dsi_dcs_write_seq(dsi, ST7703_CMD_SETCYC, 0x80);
- /* Set display resolution. */
- dsi_dcs_write_seq(dsi, ST7703_CMD_SETDISP,
0xF0, /* NL = 240 */0x12, /* RES_V_LSB = 0, BLK_CON = VSSD,* RESO_SEL = 720RGB*/0xF0 /* WHITE_GND_EN = 1 (GND),* WHITE_FRAME_SEL = 7 frames,* ISC = 0 frames*/);- dsi_dcs_write_seq(dsi, ST7703_CMD_SETEQ,
0x00, /* PNOEQ */0x00, /* NNOEQ */0x0B, /* PEQGND */0x0B, /* NEQGND */0x10, /* PEQVCI */0x10, /* NEQVCI */0x00, /* PEQVCI1 */0x00, /* NEQVCI1 */0x00, /* reserved */0x00, /* reserved */0xFF, /* reserved */0x00, /* reserved */0xC0, /* ESD_DET_DATA_WHITE = 1, ESD_WHITE_EN = 1 */0x10 /* SLPIN_OPTION = 1 (no need vsync after sleep-in)* VEDIO_NO_CHECK_EN = 0* ESD_WHITE_GND_EN = 0* ESD_DET_TIME_SEL = 0 frames*/);- /* Undocumented command. */
- dsi_dcs_write_seq(dsi, ST7703_CMD_UNK_C6, 0x01, 0x00, 0xFF, 0xFF, 0x00);
- dsi_dcs_write_seq(dsi, ST7703_CMD_SETPOWER,
0x74, /* VBTHS, VBTLS: VGH = 17V, VBL = -11V */0x00, /* FBOFF_VGH = 0, FBOFF_VGL = 0 */0x32, /* VRP */0x32, /* VRN */0x77, /* reserved */0xF1, /* APS = 1 (small),* VGL_DET_EN = 1, VGH_DET_EN = 1,* VGL_TURBO = 1, VGH_TURBO = 1*/0xFF, /* VGH1_L_DIV, VGL1_L_DIV (1.5MHz) */0xFF, /* VGH1_R_DIV, VGL1_R_DIV (1.5MHz) */0xCC, /* VGH2_L_DIV, VGL2_L_DIV (2.6MHz) */0xCC, /* VGH2_R_DIV, VGL2_R_DIV (2.6MHz) */0x77, /* VGH3_L_DIV, VGL3_L_DIV (4.5MHz) */0x77 /* VGH3_R_DIV, VGL3_R_DIV (4.5MHz) */);- /* Reference voltage. */
- dsi_dcs_write_seq(dsi, ST7703_CMD_SETBGP,
0x07, /* VREF_SEL = 4.2V */0x07 /* NVREF_SEL = 4.2V */);- dsi_dcs_write_seq(dsi, ST7703_CMD_SETVCOM,
0x2C, /* VCOMDC_F = -0.67V */0x2C /* VCOMDC_B = -0.67V */);- /* Undocumented command. */
- dsi_dcs_write_seq(dsi, ST7703_CMD_UNK_BF, 0x02, 0x11, 0x00);
- /* This command is to set forward GIP timing. */
- dsi_dcs_write_seq(dsi, ST7703_CMD_SETGIP1,
0x82, 0x10, 0x06, 0x05, 0xA2, 0x0A, 0xA5, 0x12,0x31, 0x23, 0x37, 0x83, 0x04, 0xBC, 0x27, 0x38,0x0C, 0x00, 0x03, 0x00, 0x00, 0x00, 0x0C, 0x00,0x03, 0x00, 0x00, 0x00, 0x75, 0x75, 0x31, 0x88,0x88, 0x88, 0x88, 0x88, 0x88, 0x13, 0x88, 0x64,0x64, 0x20, 0x88, 0x88, 0x88, 0x88, 0x88, 0x88,0x02, 0x88, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00);- /* This command is to set backward GIP timing. */
- dsi_dcs_write_seq(dsi, ST7703_CMD_SETGIP2,
0x02, 0x21, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00, 0x00, 0x00, 0x02, 0x46, 0x02, 0x88,0x88, 0x88, 0x88, 0x88, 0x88, 0x64, 0x88, 0x13,0x57, 0x13, 0x88, 0x88, 0x88, 0x88, 0x88, 0x88,0x75, 0x88, 0x23, 0x14, 0x00, 0x00, 0x02, 0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x03, 0x0A,0xA5, 0x00, 0x00, 0x00, 0x00);- /* Adjust the gamma characteristics of the panel. */
- dsi_dcs_write_seq(dsi, ST7703_CMD_SETGAMMA,
0x00, 0x09, 0x0D, 0x23, 0x27, 0x3C, 0x41, 0x35,0x07, 0x0D, 0x0E, 0x12, 0x13, 0x10, 0x12, 0x12,0x18, 0x00, 0x09, 0x0D, 0x23, 0x27, 0x3C, 0x41,0x35, 0x07, 0x0D, 0x0E, 0x12, 0x13, 0x10, 0x12,0x12, 0x18);- DRM_DEV_DEBUG_DRIVER(dev, "Panel init sequence done\n");
- return 0;
+}
+static int st7703_read_id(struct st7703 *ctx) +{
- struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
- u8 id1, id2, id3;
- int ret;
- ret = mipi_dsi_dcs_read(dsi, ST7703_CMD_RDID1, &id1, 1);
- if (ret < 0) {
DRM_DEV_ERROR(ctx->dev, "could not read ID1\n");return ret;- }
- ret = mipi_dsi_dcs_read(dsi, ST7703_CMD_RDID2, &id2, 1);
- if (ret < 0) {
DRM_DEV_ERROR(ctx->dev, "could not read ID2\n");return ret;- }
- ret = mipi_dsi_dcs_read(dsi, ST7703_CMD_RDID3, &id3, 1);
- if (ret < 0) {
DRM_DEV_ERROR(ctx->dev, "could not read ID3\n");return ret;- }
- DRM_DEV_INFO(ctx->dev,
"manufacturer: %02x version: %02x driver: %02x\n",id1, id2, id3);- return 0;
+}
+static int st7703_prepare(struct drm_panel *panel) +{
- struct st7703 *ctx = panel_to_st7703(panel);
- struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
- int ret;
- if (ctx->prepared)
return 0;- gpiod_set_value_cansleep(ctx->reset_gpio, 1);
- ret = regulator_bulk_enable(ctx->desc->num_supplies, ctx->supplies);
- if (ret)
return ret;- /* Wait for regulators to stabilize. */
- usleep_range(10000, 20000);
- gpiod_set_value_cansleep(ctx->reset_gpio, 0);
- /* There needs to be at least 15ms post-reset delay. */
- usleep_range(15000, 20000);
- ret = st7703_read_id(ctx);
- if (ret < 0)
goto err_poweroff;- ret = st7703_init_sequence(ctx);
- if (ret < 0) {
DRM_DEV_ERROR(ctx->dev,"Panel init sequence failed (%d)\n", ret);goto err_poweroff;- }
- ret = mipi_dsi_dcs_exit_sleep_mode(dsi);
- if (ret < 0) {
DRM_DEV_ERROR(ctx->dev,"Failed to exit sleep mode (%d)\n", ret);goto err_poweroff;- }
- msleep(120);
- ret = mipi_dsi_dcs_set_display_on(dsi);
- if (ret) {
DRM_DEV_ERROR(ctx->dev,"Failed to turn on the display (%d)\n", ret);goto err_poweroff;- }
- ctx->prepared = true;
- return 0;
+err_poweroff:
- gpiod_set_value_cansleep(ctx->reset_gpio, 1);
- regulator_bulk_disable(ctx->desc->num_supplies, ctx->supplies);
- return ret;
+}
+static int st7703_enable(struct drm_panel *panel) +{
- /*
* Avoid flicker by waiting for slightly more than 1* frame's interval.*/- msleep(50);
- return 0;
+}
+static int st7703_unprepare(struct drm_panel *panel) +{
- struct st7703 *ctx = panel_to_st7703(panel);
- struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
- int ret;
- if (!ctx->prepared)
return 0;- ret = mipi_dsi_dcs_set_display_off(dsi);
- if (ret < 0)
DRM_DEV_ERROR(ctx->dev,"Failed to turn off the display (%d)\n", ret);- ret = mipi_dsi_dcs_enter_sleep_mode(dsi);
- if (ret < 0)
DRM_DEV_ERROR(ctx->dev,"Failed to enter sleep mode (%d)\n", ret);- gpiod_set_value_cansleep(ctx->reset_gpio, 1);
- regulator_bulk_disable(ctx->desc->num_supplies, ctx->supplies);
- ctx->prepared = false;
- return 0;
+}
+static int st7703_get_modes(struct drm_panel *panel,
struct drm_connector *connector)+{
- struct st7703 *ctx = panel_to_st7703(panel);
- struct drm_display_mode *mode;
- mode = drm_mode_duplicate(connector->dev, ctx->desc->mode);
- if (!mode) {
DRM_DEV_ERROR(ctx->dev, "Failed to add mode\n");return -ENOMEM;- }
- drm_mode_set_name(mode);
- connector->display_info.width_mm = mode->width_mm;
- connector->display_info.height_mm = mode->height_mm;
- drm_mode_probed_add(connector, mode);
- return 1;
+}
+static const struct drm_panel_funcs st7703_drm_funcs = {
- .prepare = st7703_prepare,
- .enable = st7703_enable,
- .unprepare = st7703_unprepare,
- .get_modes = st7703_get_modes,
+};
+static const struct drm_display_mode xbd599_mode = {
- .hdisplay = 720,
- .hsync_start = 720 + 40,
- .hsync_end = 720 + 40 + 40,
- .htotal = 720 + 40 + 40 + 40,
- .vdisplay = 1440,
- .vsync_start = 1440 + 18,
- .vsync_end = 1440 + 18 + 10,
- .vtotal = 1440 + 18 + 10 + 17,
- .vrefresh = 60,
- .clock = 69000,
- .flags = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
- .width_mm = 68,
- .height_mm = 136,
- .type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED,
+};
+static const char * const xbd599_supply_names[] = {
- "iovcc",
- "vcc",
+};
+static const struct st7703_panel_desc xbd599_desc = {
- .mode = &xbd599_mode,
- .lanes = 4,
- .flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_SYNC_PULSE,
- .format = MIPI_DSI_FMT_RGB888,
- .supply_names = xbd599_supply_names,
- .num_supplies = ARRAY_SIZE(xbd599_supply_names),
+};
+static int st7703_probe(struct mipi_dsi_device *dsi) +{
- const struct st7703_panel_desc *desc;
- struct device *dev = &dsi->dev;
- struct st7703 *ctx;
- int i, ret;
- ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
- if (!ctx)
return -ENOMEM;- ctx->dev = dev;
- ctx->desc = desc = of_device_get_match_data(dev);
- dsi->mode_flags = desc->flags;
- dsi->format = desc->format;
- dsi->lanes = desc->lanes;
- ctx->supplies = devm_kcalloc(&dsi->dev, desc->num_supplies,
sizeof(*ctx->supplies),GFP_KERNEL);- if (!ctx->supplies)
return -ENOMEM;- for (i = 0; i < desc->num_supplies; i++)
ctx->supplies[i].supply = desc->supply_names[i];- ret = devm_regulator_bulk_get(&dsi->dev, desc->num_supplies,
ctx->supplies);- if (ret < 0)
return ret;- ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
- if (IS_ERR(ctx->reset_gpio)) {
DRM_DEV_ERROR(dev, "Can't get reset gpio\n");return PTR_ERR(ctx->reset_gpio);- }
- mipi_dsi_set_drvdata(dsi, ctx);
- drm_panel_init(&ctx->panel, &dsi->dev, &st7703_drm_funcs,
DRM_MODE_CONNECTOR_DSI);- ret = drm_panel_of_backlight(&ctx->panel);
- if (ret)
return ret;- drm_panel_add(&ctx->panel);
- ret = mipi_dsi_attach(dsi);
- if (ret < 0) {
drm_panel_remove(&ctx->panel);return ret;- }
- return 0;
+}
+static void st7703_shutdown(struct mipi_dsi_device *dsi) +{
- struct st7703 *ctx = mipi_dsi_get_drvdata(dsi);
- int ret;
- ret = drm_panel_unprepare(&ctx->panel);
- if (ret < 0)
DRM_DEV_ERROR(&dsi->dev,"Failed to unprepare panel (%d)\n", ret);+}
+static int st7703_remove(struct mipi_dsi_device *dsi) +{
- struct st7703 *ctx = mipi_dsi_get_drvdata(dsi);
- int ret;
- st7703_shutdown(dsi);
- ret = mipi_dsi_detach(dsi);
- if (ret < 0)
DRM_DEV_ERROR(&dsi->dev,"Failed to detach from DSI host (%d)\n", ret);- drm_panel_remove(&ctx->panel);
- return 0;
+}
+static const struct of_device_id st7703_of_match[] = {
- { .compatible = "xingbangda,xbd599", .data = &xbd599_desc },
- { /* sentinel */ }
+}; +MODULE_DEVICE_TABLE(of, st7703_of_match);
+static struct mipi_dsi_driver st7703_driver = {
- .probe = st7703_probe,
- .remove = st7703_remove,
- .shutdown = st7703_shutdown,
- .driver = {
.name = "st7703",.of_match_table = st7703_of_match,- },
+}; +module_mipi_dsi_driver(st7703_driver);
+MODULE_AUTHOR("Icenowy Zheng icenowy@aosc.io"); +MODULE_DESCRIPTION("DRM driver for Sitronix ST7703 MIPI DSI panel");
+MODULE_LICENSE("GPL v2");
2.27.0
dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel
dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel