[PATCH v3 3/4] phy: rockchip-typec: support variable phy config value

14 May 2018

the phy config values used to fix in dp firmware, but some boards
need change these values to do training and get the better eye diagram
result. So support that in phy driver.
Signed-off-by: Chris Zhong zyw@rock-chips.com
Signed-off-by: Lin Huang hl@rock-chips.com
---
Changes in v2:
- update patch following Enric suggest
Changes in v3:
- delete need_software_training variable
- add default phy config value, if dts do not define phy config value, use these value
drivers/phy/rockchip/phy-rockchip-typec.c | 305 ++++++++++++++++++++----------
 include/soc/rockchip/rockchip_phy_typec.h |  63 ++++++
 2 files changed, 270 insertions(+), 98 deletions(-)
 create mode 100644 include/soc/rockchip/rockchip_phy_typec.h

diff --git a/drivers/phy/rockchip/phy-rockchip-typec.c b/drivers/phy/rockchip/phy-rockchip-typec.c
index 76a4b58..10253ad 100644
--- a/drivers/phy/rockchip/phy-rockchip-typec.c
+++ b/drivers/phy/rockchip/phy-rockchip-typec.c
@@ -63,6 +63,7 @@
#include <linux/mfd/syscon.h>
 #include <linux/phy/phy.h>
+#include <soc/rockchip/rockchip_phy_typec.h>
#define CMN_SSM_BANDGAP			(0x21 << 2)
 #define CMN_SSM_BIAS			(0x22 << 2)
@@ -323,21 +324,29 @@
  * clock 0: PLL 0 div 1
  * clock 1: PLL 1 div 2
  */
-#define CLK_PLL_CONFIG			0X30
+#define CLK_PLL1_DIV1			0x20
+#define CLK_PLL1_DIV2			0x30
 #define CLK_PLL_MASK			0x33
#define CMN_READY			BIT(0)
+#define DP_PLL_CLOCK_ENABLE_ACK		BIT(3)
 #define DP_PLL_CLOCK_ENABLE		BIT(2)
+#define DP_PLL_ENABLE_ACK		BIT(1)
 #define DP_PLL_ENABLE			BIT(0)
 #define DP_PLL_DATA_RATE_RBR		((2 << 12) | (4 << 8))
 #define DP_PLL_DATA_RATE_HBR		((2 << 12) | (4 << 8))
 #define DP_PLL_DATA_RATE_HBR2		((1 << 12) | (2 << 8))
+#define DP_PLL_DATA_RATE_MASK		0xff00
-#define DP_MODE_A0			BIT(4)
-#define DP_MODE_A2			BIT(6)
-#define DP_MODE_ENTER_A0		0xc101
-#define DP_MODE_ENTER_A2		0xc104
+#define DP_MODE_MASK			0xf
+#define DP_MODE_ENTER_A0		BIT(0)
+#define DP_MODE_ENTER_A2		BIT(2)
+#define DP_MODE_ENTER_A3		BIT(3)
+#define DP_MODE_A0_ACK			BIT(4)
+#define DP_MODE_A2_ACK			BIT(6)
+#define DP_MODE_A3_ACK			BIT(7)
+#define DP_LINK_RESET_DEASSERTED	BIT(8)
#define PHY_MODE_SET_TIMEOUT		100000
@@ -349,51 +358,7 @@
 #define MODE_DFP_USB			BIT(1)
 #define MODE_DFP_DP			BIT(2)
-struct usb3phy_reg {
-	u32 offset;
-	u32 enable_bit;
-	u32 write_enable;
-};
-
-/**
- * struct rockchip_usb3phy_port_cfg: usb3-phy port configuration.
- * @reg: the base address for usb3-phy config.
- * @typec_conn_dir: the register of type-c connector direction.
- * @usb3tousb2_en: the register of type-c force usb2 to usb2 enable.
- * @external_psm: the register of type-c phy external psm clock.
- * @pipe_status: the register of type-c phy pipe status.
- * @usb3_host_disable: the register of type-c usb3 host disable.
- * @usb3_host_port: the register of type-c usb3 host port.
- * @uphy_dp_sel: the register of type-c phy DP select control.
- */
-struct rockchip_usb3phy_port_cfg {
-	unsigned int reg;
-	struct usb3phy_reg typec_conn_dir;
-	struct usb3phy_reg usb3tousb2_en;
-	struct usb3phy_reg external_psm;
-	struct usb3phy_reg pipe_status;
-	struct usb3phy_reg usb3_host_disable;
-	struct usb3phy_reg usb3_host_port;
-	struct usb3phy_reg uphy_dp_sel;
-};
-
-struct rockchip_typec_phy {
-	struct device *dev;
-	void __iomem *base;
-	struct extcon_dev *extcon;
-	struct regmap *grf_regs;
-	struct clk *clk_core;
-	struct clk *clk_ref;
-	struct reset_control *uphy_rst;
-	struct reset_control *pipe_rst;
-	struct reset_control *tcphy_rst;
-	const struct rockchip_usb3phy_port_cfg *port_cfgs;
-	/* mutex to protect access to individual PHYs */
-	struct mutex lock;
-
-	bool flip;
-	u8 mode;
-};
+#define DP_DEFAULT_RATE		162000
struct phy_reg {
    u16 value;
@@ -417,15 +382,15 @@ struct phy_reg usb3_pll_cfg[] = {
    { 0x8,		CMN_DIAG_PLL0_LF_PROG },
 };
-struct phy_reg dp_pll_cfg[] = {
+struct phy_reg dp_pll_rbr_cfg[] = {
    { 0xf0,		CMN_PLL1_VCOCAL_INIT },
    { 0x18,		CMN_PLL1_VCOCAL_ITER },
    { 0x30b9,	CMN_PLL1_VCOCAL_START },
-	{ 0x21c,	CMN_PLL1_INTDIV },
+	{ 0x87,		CMN_PLL1_INTDIV },
    { 0,		CMN_PLL1_FRACDIV },
-	{ 0x5,		CMN_PLL1_HIGH_THR },
-	{ 0x35,		CMN_PLL1_SS_CTRL1 },
-	{ 0x7f1e,	CMN_PLL1_SS_CTRL2 },
+	{ 0x22,		CMN_PLL1_HIGH_THR },
+	{ 0x8000,	CMN_PLL1_SS_CTRL1 },
+	{ 0,		CMN_PLL1_SS_CTRL2 },
    { 0x20,		CMN_PLL1_DSM_DIAG },
    { 0,		CMN_PLLSM1_USER_DEF_CTRL },
    { 0,		CMN_DIAG_PLL1_OVRD },
@@ -436,9 +401,52 @@ struct phy_reg dp_pll_cfg[] = {
    { 0x8,		CMN_DIAG_PLL1_LF_PROG },
    { 0x100,	CMN_DIAG_PLL1_PTATIS_TUNE1 },
    { 0x7,		CMN_DIAG_PLL1_PTATIS_TUNE2 },
-	{ 0x4,		CMN_DIAG_PLL1_INCLK_CTRL },
+	{ 0x1,		CMN_DIAG_PLL1_INCLK_CTRL },
+};
+
+struct phy_reg dp_pll_hbr_cfg[] = {
+	{ 0xf0,		CMN_PLL1_VCOCAL_INIT },
+	{ 0x18,		CMN_PLL1_VCOCAL_ITER },
+	{ 0x30b4,	CMN_PLL1_VCOCAL_START },
+	{ 0xe1,		CMN_PLL1_INTDIV },
+	{ 0,		CMN_PLL1_FRACDIV },
+	{ 0x5,		CMN_PLL1_HIGH_THR },
+	{ 0x8000,	CMN_PLL1_SS_CTRL1 },
+	{ 0,		CMN_PLL1_SS_CTRL2 },
+	{ 0x20,		CMN_PLL1_DSM_DIAG },
+	{ 0x1000,	CMN_PLLSM1_USER_DEF_CTRL },
+	{ 0,		CMN_DIAG_PLL1_OVRD },
+	{ 0,		CMN_DIAG_PLL1_FBH_OVRD },
+	{ 0,		CMN_DIAG_PLL1_FBL_OVRD },
+	{ 0x7,		CMN_DIAG_PLL1_V2I_TUNE },
+	{ 0x45,		CMN_DIAG_PLL1_CP_TUNE },
+	{ 0x8,		CMN_DIAG_PLL1_LF_PROG },
+	{ 0x1,		CMN_DIAG_PLL1_PTATIS_TUNE1 },
+	{ 0x1,		CMN_DIAG_PLL1_PTATIS_TUNE2 },
+	{ 0x1,		CMN_DIAG_PLL1_INCLK_CTRL },
 };
+struct phy_reg dp_pll_hbr2_cfg[] = {
+	{ 0xf0,		CMN_PLL1_VCOCAL_INIT },
+	{ 0x18,		CMN_PLL1_VCOCAL_ITER },
+	{ 0x30b4,	CMN_PLL1_VCOCAL_START },
+	{ 0xe1,		CMN_PLL1_INTDIV },
+	{ 0,		CMN_PLL1_FRACDIV },
+	{ 0x5,		CMN_PLL1_HIGH_THR },
+	{ 0x8000,	CMN_PLL1_SS_CTRL1 },
+	{ 0,		CMN_PLL1_SS_CTRL2 },
+	{ 0x20,		CMN_PLL1_DSM_DIAG },
+	{ 0x1000,	CMN_PLLSM1_USER_DEF_CTRL },
+	{ 0,		CMN_DIAG_PLL1_OVRD },
+	{ 0,		CMN_DIAG_PLL1_FBH_OVRD },
+	{ 0,		CMN_DIAG_PLL1_FBL_OVRD },
+	{ 0x7,		CMN_DIAG_PLL1_V2I_TUNE },
+	{ 0x45,		CMN_DIAG_PLL1_CP_TUNE },
+	{ 0x8,		CMN_DIAG_PLL1_LF_PROG },
+	{ 0x1,		CMN_DIAG_PLL1_PTATIS_TUNE1 },
+	{ 0x1,		CMN_DIAG_PLL1_PTATIS_TUNE2 },
+	{ 0x1,		CMN_DIAG_PLL1_INCLK_CTRL },
+};
 static const struct rockchip_usb3phy_port_cfg rk3399_usb3phy_port_cfgs[] = {
    {
    	.reg = 0xff7c0000,
@@ -463,6 +471,24 @@ static const struct rockchip_usb3phy_port_cfg rk3399_usb3phy_port_cfgs[] = {
    { /* sentinel */ }
 };
+/* default phy config */
+struct phy_config configs[3][4] = {
+	{{ 0x2a, 0x00 },
+	 { 0x1f, 0x15 },
+	 { 0x14, 0x22 },
+	 { 0x02, 0x2b } },
+
+	{{ 0x21, 0x00 },
+	 { 0x12, 0x15 },
+	 { 0x02, 0x22 },
+	 {    0,    0 } },
+
+	{{ 0x15, 0x00 },
+	 { 0x00, 0x15 },
+	 {    0,    0 },
+	 {    0,    0 } },
+};
+
 static void tcphy_cfg_24m(struct rockchip_typec_phy *tcphy)
 {
    u32 i, rdata;
@@ -484,7 +510,7 @@ static void tcphy_cfg_24m(struct rockchip_typec_phy *tcphy)
rdata = readl(tcphy->base + CMN_DIAG_HSCLK_SEL);
    rdata &= ~CLK_PLL_MASK;
-	rdata |= CLK_PLL_CONFIG;
+	rdata |= CLK_PLL1_DIV2;
    writel(rdata, tcphy->base + CMN_DIAG_HSCLK_SEL);
 }
@@ -498,17 +524,44 @@ static void tcphy_cfg_usb3_pll(struct rockchip_typec_phy *tcphy)
    	       tcphy->base + usb3_pll_cfg[i].addr);
 }
-static void tcphy_cfg_dp_pll(struct rockchip_typec_phy *tcphy)
+static void tcphy_cfg_dp_pll(struct rockchip_typec_phy *tcphy, int link_rate)
 {
-	u32 i;
+	struct phy_reg *phy_cfg;
+	u32 clk_ctrl;
+	u32 i, cfg_size, hsclk_sel;
+
+	hsclk_sel = readl(tcphy->base + CMN_DIAG_HSCLK_SEL);
+	hsclk_sel &= ~CLK_PLL_MASK;
+
+	switch (link_rate) {
+	case 162000:
+		clk_ctrl = DP_PLL_DATA_RATE_RBR;
+		hsclk_sel |= CLK_PLL1_DIV2;
+		phy_cfg = dp_pll_rbr_cfg;
+		cfg_size = ARRAY_SIZE(dp_pll_rbr_cfg);
+		break;
+	case 270000:
+		clk_ctrl = DP_PLL_DATA_RATE_HBR;
+		hsclk_sel |= CLK_PLL1_DIV2;
+		phy_cfg = dp_pll_hbr_cfg;
+		cfg_size = ARRAY_SIZE(dp_pll_hbr_cfg);
+		break;
+	case 540000:
+		clk_ctrl = DP_PLL_DATA_RATE_HBR2;
+		hsclk_sel |= CLK_PLL1_DIV1;
+		phy_cfg = dp_pll_hbr2_cfg;
+		cfg_size = ARRAY_SIZE(dp_pll_hbr2_cfg);
+		break;
+	}
+
+	clk_ctrl |= DP_PLL_CLOCK_ENABLE | DP_PLL_ENABLE;
+	writel(clk_ctrl, tcphy->base + DP_CLK_CTL);
-	/* set the default mode to RBR */
-	writel(DP_PLL_CLOCK_ENABLE | DP_PLL_ENABLE | DP_PLL_DATA_RATE_RBR,
-	       tcphy->base + DP_CLK_CTL);
+	writel(hsclk_sel, tcphy->base + CMN_DIAG_HSCLK_SEL);
/* load the configuration of PLL1 */
-	for (i = 0; i < ARRAY_SIZE(dp_pll_cfg); i++)
-		writel(dp_pll_cfg[i].value, tcphy->base + dp_pll_cfg[i].addr);
+	for (i = 0; i < cfg_size; i++)
+		writel(phy_cfg[i].value, tcphy->base + phy_cfg[i].addr);
 }
static void tcphy_tx_usb3_cfg_lane(struct rockchip_typec_phy *tcphy, u32 lane)
@@ -535,9 +588,10 @@ static void tcphy_rx_usb3_cfg_lane(struct rockchip_typec_phy *tcphy, u32 lane)
    writel(0xfb, tcphy->base + XCVR_DIAG_BIDI_CTRL(lane));
 }
-static void tcphy_dp_cfg_lane(struct rockchip_typec_phy *tcphy, u32 lane)
+static void tcphy_dp_cfg_lane(struct rockchip_typec_phy *tcphy, int link_rate,
+			      u8 swing, u8 pre_emp, u32 lane)
 {
-	u16 rdata;
+	u16 val;
writel(0xbefc, tcphy->base + XCVR_PSM_RCTRL(lane));
    writel(0x6799, tcphy->base + TX_PSC_A0(lane));
@@ -545,25 +599,31 @@ static void tcphy_dp_cfg_lane(struct rockchip_typec_phy *tcphy, u32 lane)
    writel(0x98, tcphy->base + TX_PSC_A2(lane));
    writel(0x98, tcphy->base + TX_PSC_A3(lane));
-	writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_000(lane));
-	writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_001(lane));
-	writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_010(lane));
-	writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_011(lane));
-	writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_100(lane));
-	writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_101(lane));
-	writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_110(lane));
-	writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_111(lane));
-	writel(0, tcphy->base + TX_TXCC_CPOST_MULT_10(lane));
-	writel(0, tcphy->base + TX_TXCC_CPOST_MULT_01(lane));
-	writel(0, tcphy->base + TX_TXCC_CPOST_MULT_00(lane));
-	writel(0, tcphy->base + TX_TXCC_CPOST_MULT_11(lane));
-
-	writel(0x128, tcphy->base + TX_TXCC_CAL_SCLR_MULT(lane));
-	writel(0x400, tcphy->base + TX_DIAG_TX_DRV(lane));
-
-	rdata = readl(tcphy->base + XCVR_DIAG_PLLDRC_CTRL(lane));
-	rdata = (rdata & 0x8fff) | 0x6000;
-	writel(rdata, tcphy->base + XCVR_DIAG_PLLDRC_CTRL(lane));
+	writel(tcphy->config[swing][pre_emp].swing,
+	       tcphy->base + TX_TXCC_MGNFS_MULT_000(lane));
+	writel(tcphy->config[swing][pre_emp].pe,
+	       tcphy->base + TX_TXCC_CPOST_MULT_00(lane));
+
+	if (swing == 2 && pre_emp == 0 && link_rate != 540000) {
+		writel(0x700, tcphy->base + TX_DIAG_TX_DRV(lane));
+		writel(0x13c, tcphy->base + TX_TXCC_CAL_SCLR_MULT(lane));
+	} else {
+		writel(0x128, tcphy->base + TX_TXCC_CAL_SCLR_MULT(lane));
+		writel(0x0400, tcphy->base + TX_DIAG_TX_DRV(lane));
+	}
+
+	val = readl(tcphy->base + XCVR_DIAG_PLLDRC_CTRL(lane));
+	val = val & 0x8fff;
+	switch (link_rate) {
+	case 162000:
+	case 270000:
+		val |= (6 << 12);
+		break;
+	case 540000:
+		val |= (4 << 12);
+		break;
+	}
+	writel(val, tcphy->base + XCVR_DIAG_PLLDRC_CTRL(lane));
 }
static inline int property_enable(struct rockchip_typec_phy *tcphy,
@@ -754,30 +814,33 @@ static int tcphy_phy_init(struct rockchip_typec_phy *tcphy, u8 mode)
    tcphy_cfg_24m(tcphy);
if (mode == MODE_DFP_DP) {
-		tcphy_cfg_dp_pll(tcphy);
+		tcphy_cfg_dp_pll(tcphy, DP_DEFAULT_RATE);
    	for (i = 0; i < 4; i++)
-			tcphy_dp_cfg_lane(tcphy, i);
+			tcphy_dp_cfg_lane(tcphy, DP_DEFAULT_RATE, 0, 0, i);
writel(PIN_ASSIGN_C_E, tcphy->base + PMA_LANE_CFG);
    } else {
    	tcphy_cfg_usb3_pll(tcphy);
-		tcphy_cfg_dp_pll(tcphy);
+		tcphy_cfg_dp_pll(tcphy, DP_DEFAULT_RATE);
    	if (tcphy->flip) {
    		tcphy_tx_usb3_cfg_lane(tcphy, 3);
    		tcphy_rx_usb3_cfg_lane(tcphy, 2);
-			tcphy_dp_cfg_lane(tcphy, 0);
-			tcphy_dp_cfg_lane(tcphy, 1);
+			tcphy_dp_cfg_lane(tcphy, DP_DEFAULT_RATE, 0, 0, 0);
+			tcphy_dp_cfg_lane(tcphy, DP_DEFAULT_RATE, 0, 0, 1);
    	} else {
    		tcphy_tx_usb3_cfg_lane(tcphy, 0);
    		tcphy_rx_usb3_cfg_lane(tcphy, 1);
-			tcphy_dp_cfg_lane(tcphy, 2);
-			tcphy_dp_cfg_lane(tcphy, 3);
+			tcphy_dp_cfg_lane(tcphy, DP_DEFAULT_RATE, 0, 0, 2);
+			tcphy_dp_cfg_lane(tcphy, DP_DEFAULT_RATE, 0, 0, 3);
    	}
writel(PIN_ASSIGN_D_F, tcphy->base + PMA_LANE_CFG);
    }
-	writel(DP_MODE_ENTER_A2, tcphy->base + DP_MODE_CTL);
+	val = readl(tcphy->base + DP_MODE_CTL);
+	val &= ~DP_MODE_MASK;
+	val |= DP_MODE_ENTER_A2 | DP_LINK_RESET_DEASSERTED;
+	writel(val, tcphy->base + DP_MODE_CTL);
reset_control_deassert(tcphy->uphy_rst);
@@ -990,7 +1053,7 @@ static int rockchip_dp_phy_power_on(struct phy *phy)
    property_enable(tcphy, &cfg->uphy_dp_sel, 1);
ret = readx_poll_timeout(readl, tcphy->base + DP_MODE_CTL,
-				 val, val & DP_MODE_A2, 1000,
+				 val, val & DP_MODE_A2_ACK, 1000,
    			 PHY_MODE_SET_TIMEOUT);
    if (ret < 0) {
    	dev_err(tcphy->dev, "failed to wait TCPHY enter A2\n");
@@ -999,13 +1062,19 @@ static int rockchip_dp_phy_power_on(struct phy *phy)
tcphy_dp_aux_calibration(tcphy);
-	writel(DP_MODE_ENTER_A0, tcphy->base + DP_MODE_CTL);
+	/* enter A0 mode */
+	val = readl(tcphy->base + DP_MODE_CTL);
+	val &= ~DP_MODE_MASK;
+	val |= DP_MODE_ENTER_A0;
+	writel(val, tcphy->base + DP_MODE_CTL);
ret = readx_poll_timeout(readl, tcphy->base + DP_MODE_CTL,
-				 val, val & DP_MODE_A0, 1000,
+				 val, val & DP_MODE_A0_ACK, 1000,
    			 PHY_MODE_SET_TIMEOUT);
    if (ret < 0) {
-		writel(DP_MODE_ENTER_A2, tcphy->base + DP_MODE_CTL);
+		val &= ~DP_MODE_MASK;
+		val |= DP_MODE_ENTER_A2;
+		writel(val, tcphy->base + DP_MODE_CTL);
    	dev_err(tcphy->dev, "failed to wait TCPHY enter A0\n");
    	goto power_on_finish;
    }
@@ -1023,6 +1092,7 @@ static int rockchip_dp_phy_power_on(struct phy *phy)
 static int rockchip_dp_phy_power_off(struct phy *phy)
 {
    struct rockchip_typec_phy *tcphy = phy_get_drvdata(phy);
+	u32 val;
mutex_lock(&tcphy->lock);
@@ -1031,7 +1101,10 @@ static int rockchip_dp_phy_power_off(struct phy *phy)
tcphy->mode &= ~MODE_DFP_DP;
-	writel(DP_MODE_ENTER_A2, tcphy->base + DP_MODE_CTL);
+	val = readl(tcphy->base + DP_MODE_CTL);
+	val &= ~DP_MODE_MASK;
+	val |= DP_MODE_ENTER_A2;
+	writel(val, tcphy->base + DP_MODE_CTL);
if (tcphy->mode == MODE_DISCONNECT)
    	tcphy_phy_deinit(tcphy);
@@ -1047,9 +1120,35 @@ static const struct phy_ops rockchip_dp_phy_ops = {
    .owner		= THIS_MODULE,
 };
+static int typec_dp_phy_config(struct phy *phy, int link_rate,
+			 int lanes, u8 swing, u8 pre_emp)
+{
+	struct rockchip_typec_phy *tcphy = phy_get_drvdata(phy);
+	u8 i;
+
+	tcphy_cfg_dp_pll(tcphy, link_rate);
+
+	if (tcphy->mode == MODE_DFP_DP) {
+		for (i = 0; i < 4; i++)
+			tcphy_dp_cfg_lane(tcphy, link_rate, swing, pre_emp, i);
+	} else {
+		if (tcphy->flip) {
+			tcphy_dp_cfg_lane(tcphy, link_rate, swing, pre_emp, 0);
+			tcphy_dp_cfg_lane(tcphy, link_rate, swing, pre_emp, 1);
+		} else {
+			tcphy_dp_cfg_lane(tcphy, link_rate, swing, pre_emp, 2);
+			tcphy_dp_cfg_lane(tcphy, link_rate, swing, pre_emp, 3);
+		}
+	}
+
+	return 0;
+}
+
 static int tcphy_parse_dt(struct rockchip_typec_phy *tcphy,
    		  struct device *dev)
 {
+	int ret;
+
    tcphy->grf_regs = syscon_regmap_lookup_by_phandle(dev->of_node,
    						  "rockchip,grf");
    if (IS_ERR(tcphy->grf_regs)) {
@@ -1087,6 +1186,15 @@ static int tcphy_parse_dt(struct rockchip_typec_phy *tcphy,
    	return PTR_ERR(tcphy->tcphy_rst);
    }
+	/*
+	 * check if phy_config pass from dts, if no,
+	 * use default phy config value.
+	 */
+	ret = of_property_read_u32_array(dev->of_node, "rockchip,phy_config",
+		(u32 *)tcphy->config, sizeof(tcphy->config) / sizeof(u32));
+	if (ret)
+		memcpy(tcphy->config, configs, sizeof(tcphy->config));
+
    return 0;
 }
@@ -1171,6 +1279,7 @@ static int rockchip_typec_phy_probe(struct platform_device *pdev)
    	}
    }
+	tcphy->typec_phy_config = typec_dp_phy_config;
    pm_runtime_enable(dev);
for_each_available_child_of_node(np, child_np) {
diff --git a/include/soc/rockchip/rockchip_phy_typec.h b/include/soc/rockchip/rockchip_phy_typec.h
new file mode 100644
index 0000000..be6af0e
--- /dev/null
+++ b/include/soc/rockchip/rockchip_phy_typec.h
@@ -0,0 +1,63 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) Fuzhou Rockchip Electronics Co.Ltd
+ * Author: Lin Huang hl@rock-chips.com
+ */
+
+#ifndef __SOC_ROCKCHIP_PHY_TYPEC_H
+#define __SOC_ROCKCHIP_PHY_TYPEC_H
+
+struct usb3phy_reg {
+	u32 offset;
+	u32 enable_bit;
+	u32 write_enable;
+};
+
+/**
+ * struct rockchip_usb3phy_port_cfg: usb3-phy port configuration.
+ * @reg: the base address for usb3-phy config.
+ * @typec_conn_dir: the register of type-c connector direction.
+ * @usb3tousb2_en: the register of type-c force usb2 to usb2 enable.
+ * @external_psm: the register of type-c phy external psm clock.
+ * @pipe_status: the register of type-c phy pipe status.
+ * @usb3_host_disable: the register of type-c usb3 host disable.
+ * @usb3_host_port: the register of type-c usb3 host port.
+ * @uphy_dp_sel: the register of type-c phy DP select control.
+ */
+struct rockchip_usb3phy_port_cfg {
+	unsigned int reg;
+	struct usb3phy_reg typec_conn_dir;
+	struct usb3phy_reg usb3tousb2_en;
+	struct usb3phy_reg external_psm;
+	struct usb3phy_reg pipe_status;
+	struct usb3phy_reg usb3_host_disable;
+	struct usb3phy_reg usb3_host_port;
+	struct usb3phy_reg uphy_dp_sel;
+};
+
+struct phy_config {
+	int swing;
+	int pe;
+};
+
+struct rockchip_typec_phy {
+	struct device *dev;
+	void __iomem *base;
+	struct extcon_dev *extcon;
+	struct regmap *grf_regs;
+	struct clk *clk_core;
+	struct clk *clk_ref;
+	struct reset_control *uphy_rst;
+	struct reset_control *pipe_rst;
+	struct reset_control *tcphy_rst;
+	const struct rockchip_usb3phy_port_cfg *port_cfgs;
+	/* mutex to protect access to individual PHYs */
+	struct mutex lock;
+	struct phy_config config[3][4];
+	bool flip;
+	u8 mode;
+	int (*typec_phy_config)(struct phy *phy, int link_rate,
+				int lanes, u8 swing, u8 pre_emp);
+};
+
+#endif
-- 
2.7.4


    

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

[PATCH v3 3/4] phy: rockchip-typec: support variable phy config value