Add edp controller and phy DT nodes for sc7280.
Signed-off-by: Krishna Manikandan quic_mkrishn@quicinc.com Reviewed-by: Stephen Boyd swboyd@chromium.org Signed-off-by: Sankeerth Billakanti quic_sbillaka@quicinc.com ---
Changes in v3: - Add one clock cell per line (Stephen Boyd) - Unit address should match first reg property (Stephen Boyd) - Remove new line (Stephen Boyd) - Add the dsi_phy clocks in dispcc (Kuogee Hsieh)
Changes in v2: - Move regulator definitions to board file (Matthias Kaehlcke) - Move the gpio definitions to board file (Matthias Kaehlcke) - Move the pinconf to board file (Matthias Kaehlcke) - Move status property (Stephen Boyd) - Drop flags from interrupts (Stephen Boyd) - Add clock names one per line for readability (Stephen Boyd) - Rename edp-opp-table (Stephen Boyd)
arch/arm64/boot/dts/qcom/sc7280.dtsi | 107 ++++++++++++++++++++++++++++++++++- 1 file changed, 105 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi index 12c4d32..5ad500e 100644 --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi @@ -2695,8 +2695,8 @@ <&dsi_phy 1>, <0>, <0>, - <0>, - <0>; + <&edp_phy 0>, + <&edp_phy 1>; clock-names = "bi_tcxo", "gcc_disp_gpll0_clk", "dsi0_phy_pll_out_byteclk", @@ -2784,6 +2784,13 @@ remote-endpoint = <&dsi0_in>; }; }; + + port@1 { + reg = <1>; + dpu_intf5_out: endpoint { + remote-endpoint = <&edp_in>; + }; + }; };
mdp_opp_table: opp-table { @@ -2899,6 +2906,102 @@
status = "disabled"; }; + + msm_edp: edp@aea0000 { + compatible = "qcom,sc7280-edp"; + + reg = <0 0xaea0000 0 0x200>, + <0 0xaea0200 0 0x200>, + <0 0xaea0400 0 0xc00>, + <0 0xaea1000 0 0x400>; + + interrupt-parent = <&mdss>; + interrupts = <14>; + + clocks = <&rpmhcc RPMH_CXO_CLK>, + <&gcc GCC_EDP_CLKREF_EN>, + <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&dispcc DISP_CC_MDSS_EDP_AUX_CLK>, + <&dispcc DISP_CC_MDSS_EDP_LINK_CLK>, + <&dispcc DISP_CC_MDSS_EDP_LINK_INTF_CLK>, + <&dispcc DISP_CC_MDSS_EDP_PIXEL_CLK>; + clock-names = "core_xo", + "core_ref", + "core_iface", + "core_aux", + "ctrl_link", + "ctrl_link_iface", + "stream_pixel"; + #clock-cells = <1>; + assigned-clocks = <&dispcc DISP_CC_MDSS_EDP_LINK_CLK_SRC>, + <&dispcc DISP_CC_MDSS_EDP_PIXEL_CLK_SRC>; + assigned-clock-parents = <&edp_phy 0>, <&edp_phy 1>; + + phys = <&edp_phy>; + phy-names = "dp"; + + operating-points-v2 = <&edp_opp_table>; + power-domains = <&rpmhpd SC7280_CX>; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + edp_in: endpoint { + remote-endpoint = <&dpu_intf5_out>; + }; + }; + }; + + edp_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp-160000000 { + opp-hz = /bits/ 64 <160000000>; + required-opps = <&rpmhpd_opp_low_svs>; + }; + + opp-270000000 { + opp-hz = /bits/ 64 <270000000>; + required-opps = <&rpmhpd_opp_svs>; + }; + + opp-540000000 { + opp-hz = /bits/ 64 <540000000>; + required-opps = <&rpmhpd_opp_nom>; + }; + + opp-810000000 { + opp-hz = /bits/ 64 <810000000>; + required-opps = <&rpmhpd_opp_nom>; + }; + }; + }; + + edp_phy: phy@aec2a00 { + compatible = "qcom,sc7280-edp-phy"; + + reg = <0 0xaec2a00 0 0x19c>, + <0 0xaec2200 0 0xa0>, + <0 0xaec2600 0 0xa0>, + <0 0xaec2000 0 0x1c0>; + + clocks = <&rpmhcc RPMH_CXO_CLK>, + <&gcc GCC_EDP_CLKREF_EN>; + clock-names = "aux", + "cfg_ahb"; + + #clock-cells = <1>; + #phy-cells = <0>; + + status = "disabled"; + }; };
pdc: interrupt-controller@b220000 {