From: Swati Sharma swati2.sharma@intel.com
In this patch enabled support for link status and recovery in i915 driver. HDMI link loss indication to upstream DP source is indicated via IRQ_HPD. This is followed by reading of HDMI link configuration status (HDMI_TX_LINK_ACTIVE_STATUS). If the PCON → HDMI 2.1 link status is off; reinitiate frl link training to recover. Also, HDMI FRL link error count range for each individual FRL active lane is indicated by DOWNSTREAM_HDMI_ERROR_STATUS_LN registers.
Signed-off-by: Swati Sharma swati2.sharma@intel.com Signed-off-by: Ankit Nautiyal ankit.k.nautiyal@intel.com --- drivers/gpu/drm/i915/display/intel_dp.c | 47 +++++++++++++++++++++++-- 1 file changed, 44 insertions(+), 3 deletions(-)
diff --git a/drivers/gpu/drm/i915/display/intel_dp.c b/drivers/gpu/drm/i915/display/intel_dp.c index 668165dd2b1a..e6c4cb844e37 100644 --- a/drivers/gpu/drm/i915/display/intel_dp.c +++ b/drivers/gpu/drm/i915/display/intel_dp.c @@ -5955,6 +5955,29 @@ intel_dp_check_mst_status(struct intel_dp *intel_dp) return link_ok; }
+static void +intel_dp_handle_hdmi_link_status_change(struct intel_dp *intel_dp) +{ + bool is_active; + u8 buf = 0; + + is_active = drm_dp_pcon_hdmi_link_active(&intel_dp->aux); + if (intel_dp->frl.is_trained && !is_active) { + if (drm_dp_dpcd_readb(&intel_dp->aux, DP_PCON_HDMI_LINK_CONFIG_1, &buf) < 0) + return; + + buf &= ~DP_PCON_ENABLE_HDMI_LINK; + if (drm_dp_dpcd_writeb(&intel_dp->aux, DP_PCON_HDMI_LINK_CONFIG_1, buf) < 0) + return; + + intel_dp->frl.is_trained = false; + intel_dp->frl.trained_rate_gbps = 0; + + intel_dp_check_frl_training(intel_dp); + drm_dp_pcon_hdmi_frl_link_error_count(&intel_dp->aux, &intel_dp->attached_connector->base); + } +} + static bool intel_dp_needs_link_retrain(struct intel_dp *intel_dp) { @@ -6320,7 +6343,7 @@ intel_dp_hotplug(struct intel_encoder *encoder, return state; }
-static void intel_dp_check_service_irq(struct intel_dp *intel_dp) +static void intel_dp_check_device_service_irq(struct intel_dp *intel_dp) { struct drm_i915_private *i915 = dp_to_i915(intel_dp); u8 val; @@ -6344,6 +6367,23 @@ static void intel_dp_check_service_irq(struct intel_dp *intel_dp) drm_dbg_kms(&i915->drm, "Sink specific irq unhandled\n"); }
+static void intel_dp_check_link_service_irq(struct intel_dp *intel_dp) +{ + u8 val; + + if (intel_dp->dpcd[DP_DPCD_REV] < 0x11) + return; + + if (drm_dp_dpcd_readb(&intel_dp->aux, + DP_LINK_SERVICE_IRQ_VECTOR_ESI0, &val) != 1 || !val) + return; + + drm_dp_dpcd_writeb(&intel_dp->aux, DP_LINK_SERVICE_IRQ_VECTOR_ESI0, val); + + if (val & HDMI_LINK_STATUS_CHANGED) + intel_dp_handle_hdmi_link_status_change(intel_dp); +} + /* * According to DP spec * 5.1.2: @@ -6383,7 +6423,8 @@ intel_dp_short_pulse(struct intel_dp *intel_dp) return false; }
- intel_dp_check_service_irq(intel_dp); + intel_dp_check_device_service_irq(intel_dp); + intel_dp_check_link_service_irq(intel_dp);
/* Handle CEC interrupts, if any */ drm_dp_cec_irq(&intel_dp->aux); @@ -6815,7 +6856,7 @@ intel_dp_detect(struct drm_connector *connector, to_intel_connector(connector)->detect_edid) status = connector_status_connected;
- intel_dp_check_service_irq(intel_dp); + intel_dp_check_device_service_irq(intel_dp);
out: if (status != connector_status_connected && !intel_dp->is_mst)