* Converted .txt bindings to .yaml (by Sam Ravnborg sam@ravnborg.org - big THANKS)
RFC V1 2020-02-26 20:13:06: This patch series adds HDMI output to the jz4780/CI20 board.
It is based on taking the old 3.18 vendor kernel and trying to achieve the same with modern DTS setup and new/modified drivers.
Unfortunately, in this first RFC, only EDID and creation of /dev/fb0 are working. Also, HDMI hot plugging is detected.
But there is no HDMI output signal. So some tiny piece seems to be missing to enable/configure the Synposys HDMI controller.
We need help from the community to fix this.
Original authors of most patches are * Paul Boddie paul@boddie.org.uk * Zubair Lutfullah Kakakhel Zubair.Kakakhel@imgtec.com
H. Nikolaus Schaller (2): drm: ingenic-drm: add MODULE_DEVICE_TABLE MIPS: CI20: defconfig: configure for DRM_DW_HDMI_JZ4780
Paul Boddie (4): drm: ingenic: add jz4780 Synopsys HDMI driver. pinctrl: ingenic: add hdmi-ddc pin control group MIPS: DTS: jz4780: account for Synopsys HDMI driver and LCD controller MIPS: DTS: CI20: add HDMI setup
Sam Ravnborg (2): dt-bindings: display: add ingenic-jz4780-lcd DT Schema dt-bindings: display: add ingenic-jz4780-hdmi DT Schema
.../bindings/display/ingenic-jz4780-hdmi.yaml | 83 ++++++++++++ .../bindings/display/ingenic-jz4780-lcd.yaml | 78 ++++++++++++ arch/mips/boot/dts/ingenic/ci20.dts | 64 ++++++++++ arch/mips/boot/dts/ingenic/jz4780.dtsi | 32 +++++ arch/mips/configs/ci20_defconfig | 3 + drivers/gpu/drm/ingenic/Kconfig | 8 ++ drivers/gpu/drm/ingenic/Makefile | 1 + drivers/gpu/drm/ingenic/dw_hdmi-jz4780.c | 120 ++++++++++++++++++ drivers/gpu/drm/ingenic/ingenic-drm.c | 2 + drivers/pinctrl/pinctrl-ingenic.c | 7 + 10 files changed, 398 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/ingenic-jz4780-hdmi.yaml create mode 100644 Documentation/devicetree/bindings/display/ingenic-jz4780-lcd.yaml create mode 100644 drivers/gpu/drm/ingenic/dw_hdmi-jz4780.c
From: Sam Ravnborg sam@ravnborg.org
Add DT bindings for the LCD controller on the jz4780 SoC Based on .txt binding from Zubair Lutfullah Kakakhel
Signed-off-by: Sam Ravnborg sam@ravnborg.org Cc: Zubair Lutfullah Kakakhel Zubair.Kakakhel@imgtec.com Cc: H. Nikolaus Schaller hns@goldelico.com Cc: Rob Herring robh@kernel.org Cc: devicetree@vger.kernel.org --- .../bindings/display/ingenic-jz4780-lcd.yaml | 78 +++++++++++++++++++ 1 file changed, 78 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/ingenic-jz4780-lcd.yaml
diff --git a/Documentation/devicetree/bindings/display/ingenic-jz4780-lcd.yaml b/Documentation/devicetree/bindings/display/ingenic-jz4780-lcd.yaml new file mode 100644 index 000000000000..c71415a3a342 --- /dev/null +++ b/Documentation/devicetree/bindings/display/ingenic-jz4780-lcd.yaml @@ -0,0 +1,78 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/ingenic-jz4780-lcd.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Bindings for Ingenic JZ4780 LCD Controller + +maintainers: + - Zubair Lutfullah Kakakhel Zubair.Kakakhel@imgtec.com + - H. Nikolaus Schaller hns@goldelico.com + +description: | + LCD Controller is the Display Controller for the Ingenic JZ4780 SoC + +properties: + compatible: + items: + - const: ingenic,jz4780-lcd + + reg: + maxItems: 1 + description: the address & size of the LCD controller registers + + interrupts: + maxItems: 1 + description: Specifies the interrupt provided by parent + + clocks: + maxItems: 2 + description: Clock specifiers for the JZ4780_CLK_TVE JZ4780_CLK_LCD0PIXCLK + + clock-names: + items: + - const: lcd_clk + - const: lcd_pixclk + + port: + type: object + description: | + A port node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/jz4780-cgu.h> + lcd: jz4780-lcdk@0x13050000 { + compatible = "ingenic,jz4780-lcd"; + reg = <0x13050000 0x1800>; + + clocks = <&cgu JZ4780_CLK_TVE>, <&cgu JZ4780_CLK_LCD0PIXCLK>; + clock-names = "lcd_clk", "lcd_pixclk"; + + interrupt-parent = <&intc>; + interrupts = <31>; + + jz4780_lcd_out: port { + #address-cells = <1>; + #size-cells = <0>; + + jz4780_out_hdmi: endpoint@0 { + reg = <0>; + remote-endpoint = <&hdmi_in_lcd>; + }; + }; + }; + +...
Hi Nikolaus.
On Fri, Feb 28, 2020 at 07:19:26PM +0100, H. Nikolaus Schaller wrote:
From: Sam Ravnborg sam@ravnborg.org
Add DT bindings for the LCD controller on the jz4780 SoC Based on .txt binding from Zubair Lutfullah Kakakhel
Signed-off-by: Sam Ravnborg sam@ravnborg.org Cc: Zubair Lutfullah Kakakhel Zubair.Kakakhel@imgtec.com Cc: H. Nikolaus Schaller hns@goldelico.com Cc: Rob Herring robh@kernel.org Cc: devicetree@vger.kernel.org
As this patch was sent to you and you forward it you need to testify that this is OK. To do so follow the rules of the Developemnt Certificate of Origin as can be found in SubmittingPatches.rst.
In other words - you need to add your Signed-off-by: xxx <mail> to the patch. In the end we want to be able to see the patch the patch has taken reading the Signed-off-by: lines from top to bottom.
Please check other patches in this series for the same issue.
Sam
.../bindings/display/ingenic-jz4780-lcd.yaml | 78 +++++++++++++++++++ 1 file changed, 78 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/ingenic-jz4780-lcd.yaml
diff --git a/Documentation/devicetree/bindings/display/ingenic-jz4780-lcd.yaml b/Documentation/devicetree/bindings/display/ingenic-jz4780-lcd.yaml new file mode 100644 index 000000000000..c71415a3a342 --- /dev/null +++ b/Documentation/devicetree/bindings/display/ingenic-jz4780-lcd.yaml @@ -0,0 +1,78 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/ingenic-jz4780-lcd.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml#
+title: Bindings for Ingenic JZ4780 LCD Controller
+maintainers:
- Zubair Lutfullah Kakakhel Zubair.Kakakhel@imgtec.com
- H. Nikolaus Schaller hns@goldelico.com
+description: |
- LCD Controller is the Display Controller for the Ingenic JZ4780 SoC
+properties:
- compatible:
- items:
- const: ingenic,jz4780-lcd- reg:
- maxItems: 1
- description: the address & size of the LCD controller registers
- interrupts:
- maxItems: 1
- description: Specifies the interrupt provided by parent
- clocks:
- maxItems: 2
- description: Clock specifiers for the JZ4780_CLK_TVE JZ4780_CLK_LCD0PIXCLK
- clock-names:
- items:
- const: lcd_clk- const: lcd_pixclk- port:
- type: object
- description: |
A port node with endpoint definitions as defined inDocumentation/devicetree/bindings/media/video-interfaces.txt+required:
- compatible
- reg
- interrupts
- clocks
- clock-names
- port
+additionalProperties: false
+examples:
- |
- #include <dt-bindings/clock/jz4780-cgu.h>
- lcd: jz4780-lcdk@0x13050000 {
compatible = "ingenic,jz4780-lcd";reg = <0x13050000 0x1800>;clocks = <&cgu JZ4780_CLK_TVE>, <&cgu JZ4780_CLK_LCD0PIXCLK>;clock-names = "lcd_clk", "lcd_pixclk";interrupt-parent = <&intc>;interrupts = <31>;jz4780_lcd_out: port {#address-cells = <1>;#size-cells = <0>;jz4780_out_hdmi: endpoint@0 {reg = <0>;remote-endpoint = <&hdmi_in_lcd>;};};- };
+...
2.23.0
Hi Sam,
Am 28.02.2020 um 19:42 schrieb Sam Ravnborg sam@ravnborg.org:
Hi Nikolaus.
On Fri, Feb 28, 2020 at 07:19:26PM +0100, H. Nikolaus Schaller wrote:
From: Sam Ravnborg sam@ravnborg.org
Add DT bindings for the LCD controller on the jz4780 SoC Based on .txt binding from Zubair Lutfullah Kakakhel
Signed-off-by: Sam Ravnborg sam@ravnborg.org Cc: Zubair Lutfullah Kakakhel Zubair.Kakakhel@imgtec.com Cc: H. Nikolaus Schaller hns@goldelico.com Cc: Rob Herring robh@kernel.org Cc: devicetree@vger.kernel.org
As this patch was sent to you and you forward it you need to testify that this is OK. To do so follow the rules of the Developemnt Certificate of Origin as can be found in SubmittingPatches.rst.
In other words - you need to add your Signed-off-by: xxx <mail> to the patch. In the end we want to be able to see the patch the patch has taken reading the Signed-off-by: lines from top to bottom.
Ok, never someone explained this as precise as you did. Thanks!
Please check other patches in this series for the same issue.
Ok.
BR and thanks, Nikolaus
Sam
.../bindings/display/ingenic-jz4780-lcd.yaml | 78 +++++++++++++++++++ 1 file changed, 78 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/ingenic-jz4780-lcd.yaml
diff --git a/Documentation/devicetree/bindings/display/ingenic-jz4780-lcd.yaml b/Documentation/devicetree/bindings/display/ingenic-jz4780-lcd.yaml new file mode 100644 index 000000000000..c71415a3a342 --- /dev/null +++ b/Documentation/devicetree/bindings/display/ingenic-jz4780-lcd.yaml @@ -0,0 +1,78 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/ingenic-jz4780-lcd.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml#
+title: Bindings for Ingenic JZ4780 LCD Controller
+maintainers:
- Zubair Lutfullah Kakakhel Zubair.Kakakhel@imgtec.com
- H. Nikolaus Schaller hns@goldelico.com
+description: |
- LCD Controller is the Display Controller for the Ingenic JZ4780 SoC
+properties:
- compatible:
- items:
- const: ingenic,jz4780-lcd- reg:
- maxItems: 1
- description: the address & size of the LCD controller registers
- interrupts:
- maxItems: 1
- description: Specifies the interrupt provided by parent
- clocks:
- maxItems: 2
- description: Clock specifiers for the JZ4780_CLK_TVE JZ4780_CLK_LCD0PIXCLK
- clock-names:
- items:
- const: lcd_clk- const: lcd_pixclk- port:
- type: object
- description: |
A port node with endpoint definitions as defined inDocumentation/devicetree/bindings/media/video-interfaces.txt+required:
- compatible
- reg
- interrupts
- clocks
- clock-names
- port
+additionalProperties: false
+examples:
- |
- #include <dt-bindings/clock/jz4780-cgu.h>
- lcd: jz4780-lcdk@0x13050000 {
compatible = "ingenic,jz4780-lcd";reg = <0x13050000 0x1800>;clocks = <&cgu JZ4780_CLK_TVE>, <&cgu JZ4780_CLK_LCD0PIXCLK>;clock-names = "lcd_clk", "lcd_pixclk";interrupt-parent = <&intc>;interrupts = <31>;jz4780_lcd_out: port {#address-cells = <1>;#size-cells = <0>;jz4780_out_hdmi: endpoint@0 {reg = <0>;remote-endpoint = <&hdmi_in_lcd>;};};- };
+...
2.23.0
Dr. Nikolaus Schaller Geschäftsführer / Managing Director
Modiblast Pharma GmbH Buchenstraße 3 82041 Oberhaching
Tel. +49-89-1226-4666 Mail nikolaus.schaller@modiblast.com
Der Inhalt dieser E-Mail (einschliesslich etwaiger beigefuegter Dateien) ist vertraulich und nur für den Empfaenger bestimmt. Sollten Sie nicht der bestimmungsgemaesse Empfaenger sein, ist Ihnen jegliche Offenlegung, Vervielfaeltigung, Weitergabe oder Nutzung des Inhalts untersagt. Bitte informieren Sie in diesem Fall unverzueglich den Absender und loeschen Sie die E-Mail (einschliesslich etwaiger beigefuegter Dateien) von Ihrem System. Vielen Dank.
The contents of this e-mail (including any attachments) are confidential and may be legally privileged. If you are not the intended recipient of this e-mail, any disclosure, copying, distribution or use of its contents is strictly prohibited, and you should please notify the sender immediately and then delete it (including any attachments) from your system. Thank you.
HRB 254854 (Amtsgericht München) Geschäftsführer: Prof. Dr. Helga Schmetzer, Dr. Octavian Schatz, Dr. Nikolaus Schaller www.modiblast.com
On Fri, 28 Feb 2020 19:19:26 +0100, "H. Nikolaus Schaller" wrote:
From: Sam Ravnborg sam@ravnborg.org
Add DT bindings for the LCD controller on the jz4780 SoC Based on .txt binding from Zubair Lutfullah Kakakhel
Signed-off-by: Sam Ravnborg sam@ravnborg.org Cc: Zubair Lutfullah Kakakhel Zubair.Kakakhel@imgtec.com Cc: H. Nikolaus Schaller hns@goldelico.com Cc: Rob Herring robh@kernel.org Cc: devicetree@vger.kernel.org
.../bindings/display/ingenic-jz4780-lcd.yaml | 78 +++++++++++++++++++ 1 file changed, 78 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/ingenic-jz4780-lcd.yaml
My bot found errors running 'make dt_binding_check' on your patch:
Documentation/devicetree/bindings/display/simple-framebuffer.example.dts:21.16-37.11: Warning (chosen_node_is_root): /example-0/chosen: chosen node must be at root node /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/display/ingenic-jz4780-lcd.example.dt.yaml: example-0: 'jz4780-lcdk@0x13050000' does not match any of the regexes: '.*-names$', '.*-supply$', '^#.*-cells$', '^#[a-zA-Z0-9,+\-._]{0,63}$', '^[a-zA-Z][a-zA-Z0-9,+\-._]{0,63}$', '^[a-zA-Z][a-zA-Z0-9,+\-._]{0,63}@[0-9a-fA-F]+(,[0-9a-fA-F]+)*$', '^__.*__$', 'pinctrl-[0-9]+'
See https://patchwork.ozlabs.org/patch/1246780 Please check and re-submit.
Hi Nikolaus,
Le ven., févr. 28, 2020 at 19:19, H. Nikolaus Schaller hns@goldelico.com a écrit :
From: Sam Ravnborg sam@ravnborg.org
Add DT bindings for the LCD controller on the jz4780 SoC Based on .txt binding from Zubair Lutfullah Kakakhel
If you mean Documentation/devicetree/bindings/display/ingenic,lcd.txt then it was written by me.
Signed-off-by: Sam Ravnborg sam@ravnborg.org Cc: Zubair Lutfullah Kakakhel Zubair.Kakakhel@imgtec.com Cc: H. Nikolaus Schaller hns@goldelico.com Cc: Rob Herring robh@kernel.org Cc: devicetree@vger.kernel.org
.../bindings/display/ingenic-jz4780-lcd.yaml | 78 +++++++++++++++++++ 1 file changed, 78 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/ingenic-jz4780-lcd.yaml
diff --git a/Documentation/devicetree/bindings/display/ingenic-jz4780-lcd.yaml b/Documentation/devicetree/bindings/display/ingenic-jz4780-lcd.yaml new file mode 100644 index 000000000000..c71415a3a342 --- /dev/null +++ b/Documentation/devicetree/bindings/display/ingenic-jz4780-lcd.yaml @@ -0,0 +1,78 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/ingenic-jz4780-lcd.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml#
+title: Bindings for Ingenic JZ4780 LCD Controller
+maintainers:
- Zubair Lutfullah Kakakhel Zubair.Kakakhel@imgtec.com
- H. Nikolaus Schaller hns@goldelico.com
I'm the author of the driver, please put me here; and remove Zubair, which 1. didn't touch the DRM driver at all, and 2. isn't working at ImgTec anymore. Also, no need to put yourself here, unless you maintain the Ingenic DRM/KMS driver.
+description: |
- LCD Controller is the Display Controller for the Ingenic JZ4780 SoC
+properties:
You should add a '$nodename' property.
- compatible:
- items:
- const: ingenic,jz4780-lcd
The .txt lists more compatible strings. Please add them all.
- reg:
- maxItems: 1
- description: the address & size of the LCD controller registers
Drop the description here,
- interrupts:
- maxItems: 1
- description: Specifies the interrupt provided by parent
and here.
- clocks:
- maxItems: 2
- description: Clock specifiers for the JZ4780_CLK_TVE
JZ4780_CLK_LCD0PIXCLK
Add one 'description:' per item.
- clock-names:
- items:
- const: lcd_clk- const: lcd_pixclk- port:
- type: object
- description: |
A port node with endpoint definitions as defined inDocumentation/devicetree/bindings/media/video-interfaces.txt+required:
- compatible
- reg
- interrupts
- clocks
- clock-names
- port
+additionalProperties: false
+examples:
- |
- #include <dt-bindings/clock/jz4780-cgu.h>
- lcd: jz4780-lcdk@0x13050000 {
The node name does not comply with the DT spec, it should be 'lcd-controller'.
Cheers, -Paul
compatible = "ingenic,jz4780-lcd";reg = <0x13050000 0x1800>;clocks = <&cgu JZ4780_CLK_TVE>, <&cgu JZ4780_CLK_LCD0PIXCLK>;clock-names = "lcd_clk", "lcd_pixclk";interrupt-parent = <&intc>;interrupts = <31>;jz4780_lcd_out: port {#address-cells = <1>;#size-cells = <0>;jz4780_out_hdmi: endpoint@0 {reg = <0>;remote-endpoint = <&hdmi_in_lcd>;};};- };
+...
2.23.0
Hi Paul,
Am 02.03.2020 um 20:10 schrieb Paul Cercueil paul@crapouillou.net:
Hi Nikolaus,
Le ven., févr. 28, 2020 at 19:19, H. Nikolaus Schaller hns@goldelico.com a écrit :
From: Sam Ravnborg sam@ravnborg.org Add DT bindings for the LCD controller on the jz4780 SoC Based on .txt binding from Zubair Lutfullah Kakakhel
If you mean Documentation/devicetree/bindings/display/ingenic,lcd.txt then it was written by me.
Ah, ok. We didn't recognise this before. 6 eyes see more than 4...
I just did cherry-pick this old 4.0 patch from 2015 by Zubair and it created a ingenic-jz4780-lcd.txt:
https://lore.kernel.org/patchwork/patch/547872/
and Sam was so kind to convert it to yaml.
Signed-off-by: Sam Ravnborg sam@ravnborg.org Cc: Zubair Lutfullah Kakakhel Zubair.Kakakhel@imgtec.com Cc: H. Nikolaus Schaller hns@goldelico.com Cc: Rob Herring robh@kernel.org Cc: devicetree@vger.kernel.org
.../bindings/display/ingenic-jz4780-lcd.yaml | 78 +++++++++++++++++++ 1 file changed, 78 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/ingenic-jz4780-lcd.yaml diff --git a/Documentation/devicetree/bindings/display/ingenic-jz4780-lcd.yaml b/Documentation/devicetree/bindings/display/ingenic-jz4780-lcd.yaml new file mode 100644 index 000000000000..c71415a3a342 --- /dev/null +++ b/Documentation/devicetree/bindings/display/ingenic-jz4780-lcd.yaml @@ -0,0 +1,78 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/ingenic-jz4780-lcd.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml#
+title: Bindings for Ingenic JZ4780 LCD Controller
+maintainers:
- Zubair Lutfullah Kakakhel Zubair.Kakakhel@imgtec.com
- H. Nikolaus Schaller hns@goldelico.com
I'm the author of the driver, please put me here; and remove Zubair, which 1. didn't touch the DRM driver at all, and 2. isn't working at ImgTec anymore.
Yes that is true.
Also, no need to put yourself here, unless you maintain the Ingenic DRM/KMS driver.
Agreed. That was suggested by Sam.
+description: |
- LCD Controller is the Display Controller for the Ingenic JZ4780 SoC
+properties:
You should add a '$nodename' property.
- compatible:
- items:
- const: ingenic,jz4780-lcdThe .txt lists more compatible strings. Please add them all.
- reg:
- maxItems: 1
- description: the address & size of the LCD controller registers
Drop the description here,
- interrupts:
- maxItems: 1
- description: Specifies the interrupt provided by parent
and here.
- clocks:
- maxItems: 2
- description: Clock specifiers for the JZ4780_CLK_TVE JZ4780_CLK_LCD0PIXCLK
Add one 'description:' per item.
- clock-names:
- items:
- const: lcd_clk- const: lcd_pixclk- port:
- type: object
- description: |
A port node with endpoint definitions as defined inDocumentation/devicetree/bindings/media/video-interfaces.txt+required:
- compatible
- reg
- interrupts
- clocks
- clock-names
- port
+additionalProperties: false
+examples:
- |
- #include <dt-bindings/clock/jz4780-cgu.h>
- lcd: jz4780-lcdk@0x13050000 {
The node name does not comply with the DT spec, it should be 'lcd-controller'.
Ok, I think I'll review all so that it does match/replace Documentation/devicetree/bindings/display/ingenic,lcd.txt and no information is lost.
Cheers, -Paul
BR and thanks, Nikolaus
From: Sam Ravnborg sam@ravnborg.org
Add DT bindings for the hdmi driver for the Ingenic JZ4780 SoC. Based on .txt binding from Zubair Lutfullah Kakakhel
Signed-off-by: Sam Ravnborg sam@ravnborg.org Cc: Zubair Lutfullah Kakakhel Zubair.Kakakhel@imgtec.com Cc: H. Nikolaus Schaller hns@goldelico.com Cc: Rob Herring robh@kernel.org Cc: devicetree@vger.kernel.org --- .../bindings/display/ingenic-jz4780-hdmi.yaml | 83 +++++++++++++++++++ 1 file changed, 83 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/ingenic-jz4780-hdmi.yaml
diff --git a/Documentation/devicetree/bindings/display/ingenic-jz4780-hdmi.yaml b/Documentation/devicetree/bindings/display/ingenic-jz4780-hdmi.yaml new file mode 100644 index 000000000000..9b71c427bd69 --- /dev/null +++ b/Documentation/devicetree/bindings/display/ingenic-jz4780-hdmi.yaml @@ -0,0 +1,83 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/ingenic-jz4780-hdmi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Bindings for Ingenic JZ4780 HDMI Transmitter + +maintainers: + - Zubair Lutfullah Kakakhel Zubair.Kakakhel@imgtec.com + - H. Nikolaus Schaller hns@goldelico.com + +description: | + The HDMI Transmitter in the Ingenic JZ4780 is a Synopsys DesignWare HDMI 1.4 + TX controller IP with accompanying PHY IP. + +allOf: + - $ref: panel/panel-common.yaml# + +properties: + compatible: + items: + - const: ingenic,jz4780-hdmi + + reg: + maxItems: 1 + description: the address & size of the LCD controller registers + + reg-io-width: + const: 4 + + interrupts: + maxItems: 1 + description: Specifies the interrupt provided by parent + + clocks: + maxItems: 2 + description: Clock specifiers for isrf and iahb clocks + + clock-names: + items: + - const: isfr + - const: iahb + + ddc-i2c-bus: true + ports: true + +required: + - compatible + - clocks + - clock-names + - ports + - reg-io-width + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/jz4780-cgu.h> + + hdmi: hdmi@10180000 { + compatible = "ingenic,jz4780-hdmi"; + reg = <0x10180000 0x8000>; + reg-io-width = <4>; + ddc-i2c-bus = <&i2c4>; + interrupt-parent = <&intc>; + interrupts = <3>; + clocks = <&cgu JZ4780_CLK_HDMI>, <&cgu JZ4780_CLK_AHB0>; + clock-names = "isfr", "iahb"; + + ports { + hdmi_in: port { + #address-cells = <1>; + #size-cells = <0>; + hdmi_in_lcd: endpoint@0 { + reg = <0>; + remote-endpoint = <&jz4780_out_hdmi>; + }; + }; + }; + }; + +...
Hi Nikolaus,
Le ven., févr. 28, 2020 at 19:19, H. Nikolaus Schaller hns@goldelico.com a écrit :
From: Sam Ravnborg sam@ravnborg.org
Add DT bindings for the hdmi driver for the Ingenic JZ4780 SoC. Based on .txt binding from Zubair Lutfullah Kakakhel
Signed-off-by: Sam Ravnborg sam@ravnborg.org Cc: Zubair Lutfullah Kakakhel Zubair.Kakakhel@imgtec.com Cc: H. Nikolaus Schaller hns@goldelico.com Cc: Rob Herring robh@kernel.org Cc: devicetree@vger.kernel.org
.../bindings/display/ingenic-jz4780-hdmi.yaml | 83 +++++++++++++++++++ 1 file changed, 83 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/ingenic-jz4780-hdmi.yaml
diff --git a/Documentation/devicetree/bindings/display/ingenic-jz4780-hdmi.yaml b/Documentation/devicetree/bindings/display/ingenic-jz4780-hdmi.yaml new file mode 100644 index 000000000000..9b71c427bd69 --- /dev/null +++ b/Documentation/devicetree/bindings/display/ingenic-jz4780-hdmi.yaml @@ -0,0 +1,83 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/ingenic-jz4780-hdmi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml#
+title: Bindings for Ingenic JZ4780 HDMI Transmitter
+maintainers:
- Zubair Lutfullah Kakakhel Zubair.Kakakhel@imgtec.com
- H. Nikolaus Schaller hns@goldelico.com
Did Zubair write this glue driver? He's been MIA for a while, doesn't work at ImgTec anymore, and this email doesn't work.
+description: |
- The HDMI Transmitter in the Ingenic JZ4780 is a Synopsys
DesignWare HDMI 1.4
- TX controller IP with accompanying PHY IP.
+allOf:
- $ref: panel/panel-common.yaml#
+properties:
- compatible:
- items:
- const: ingenic,jz4780-hdmi- reg:
- maxItems: 1
- description: the address & size of the LCD controller registers
Remove the description here,
- reg-io-width:
- const: 4
- interrupts:
- maxItems: 1
- description: Specifies the interrupt provided by parent
and here.
The rule is that if there is only one "reg", "interrupts" or "clocks" entry then a description is not needed as it's pretty obvious what it's for.
- clocks:
- maxItems: 2
- description: Clock specifiers for isrf and iahb clocks
You need two 'description:' like this:
clocks: items: - description: ISRF clock - description: IAHB clock
Cheers, -Paul
- clock-names:
- items:
- const: isfr- const: iahb- ddc-i2c-bus: true
- ports: true
+required:
- compatible
- clocks
- clock-names
- ports
- reg-io-width
+additionalProperties: false
+examples:
- |
- #include <dt-bindings/clock/jz4780-cgu.h>
- hdmi: hdmi@10180000 {
compatible = "ingenic,jz4780-hdmi";reg = <0x10180000 0x8000>;reg-io-width = <4>;ddc-i2c-bus = <&i2c4>;interrupt-parent = <&intc>;interrupts = <3>;clocks = <&cgu JZ4780_CLK_HDMI>, <&cgu JZ4780_CLK_AHB0>;clock-names = "isfr", "iahb";ports {hdmi_in: port {#address-cells = <1>;#size-cells = <0>;hdmi_in_lcd: endpoint@0 {reg = <0>;remote-endpoint = <&jz4780_out_hdmi>;};};};- };
+...
2.23.0
Am 02.03.2020 um 20:19 schrieb Paul Cercueil paul@crapouillou.net:
Hi Nikolaus,
Le ven., févr. 28, 2020 at 19:19, H. Nikolaus Schaller hns@goldelico.com a écrit :
From: Sam Ravnborg sam@ravnborg.org Add DT bindings for the hdmi driver for the Ingenic JZ4780 SoC. Based on .txt binding from Zubair Lutfullah Kakakhel Signed-off-by: Sam Ravnborg sam@ravnborg.org Cc: Zubair Lutfullah Kakakhel Zubair.Kakakhel@imgtec.com Cc: H. Nikolaus Schaller hns@goldelico.com Cc: Rob Herring robh@kernel.org Cc: devicetree@vger.kernel.org
.../bindings/display/ingenic-jz4780-hdmi.yaml | 83 +++++++++++++++++++ 1 file changed, 83 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/ingenic-jz4780-hdmi.yaml diff --git a/Documentation/devicetree/bindings/display/ingenic-jz4780-hdmi.yaml b/Documentation/devicetree/bindings/display/ingenic-jz4780-hdmi.yaml new file mode 100644 index 000000000000..9b71c427bd69 --- /dev/null +++ b/Documentation/devicetree/bindings/display/ingenic-jz4780-hdmi.yaml @@ -0,0 +1,83 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/ingenic-jz4780-hdmi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml#
+title: Bindings for Ingenic JZ4780 HDMI Transmitter
+maintainers:
- Zubair Lutfullah Kakakhel Zubair.Kakakhel@imgtec.com
- H. Nikolaus Schaller hns@goldelico.com
Did Zubair write this glue driver? He's been MIA for a while, doesn't work at ImgTec anymore, and this email doesn't work.
He did write the original .txt version of [RFC v1 2/8] and Sam simply added him.
+description: |
- The HDMI Transmitter in the Ingenic JZ4780 is a Synopsys DesignWare HDMI 1.4
- TX controller IP with accompanying PHY IP.
+allOf:
- $ref: panel/panel-common.yaml#
+properties:
- compatible:
- items:
- const: ingenic,jz4780-hdmi- reg:
- maxItems: 1
- description: the address & size of the LCD controller registers
Remove the description here,
- reg-io-width:
- const: 4
- interrupts:
- maxItems: 1
- description: Specifies the interrupt provided by parent
and here.
The rule is that if there is only one "reg", "interrupts" or "clocks" entry then a description is not needed as it's pretty obvious what it's for.
- clocks:
- maxItems: 2
- description: Clock specifiers for isrf and iahb clocks
You need two 'description:' like this:
clocks: items:
- description: ISRF clock
- description: IAHB clock
Ok.
BR and thanks, Nikolaus
so that the driver can load by matching the device tree if compiled as module.
Signed-off-by: H. Nikolaus Schaller hns@goldelico.com --- drivers/gpu/drm/ingenic/ingenic-drm.c | 2 ++ 1 file changed, 2 insertions(+)
diff --git a/drivers/gpu/drm/ingenic/ingenic-drm.c b/drivers/gpu/drm/ingenic/ingenic-drm.c index 6d47ef7b148c..d8617096dd8e 100644 --- a/drivers/gpu/drm/ingenic/ingenic-drm.c +++ b/drivers/gpu/drm/ingenic/ingenic-drm.c @@ -844,6 +844,8 @@ static const struct of_device_id ingenic_drm_of_match[] = { { /* sentinel */ }, };
+MODULE_DEVICE_TABLE(of, ingenic_drm_of_match); + static struct platform_driver ingenic_drm_driver = { .driver = { .name = "ingenic-drm",
Hi Nikolaus,
Le ven., févr. 28, 2020 at 19:19, H. Nikolaus Schaller hns@goldelico.com a écrit :
so that the driver can load by matching the device tree if compiled as module.
Signed-off-by: H. Nikolaus Schaller hns@goldelico.com
drivers/gpu/drm/ingenic/ingenic-drm.c | 2 ++ 1 file changed, 2 insertions(+)
diff --git a/drivers/gpu/drm/ingenic/ingenic-drm.c b/drivers/gpu/drm/ingenic/ingenic-drm.c index 6d47ef7b148c..d8617096dd8e 100644 --- a/drivers/gpu/drm/ingenic/ingenic-drm.c +++ b/drivers/gpu/drm/ingenic/ingenic-drm.c @@ -844,6 +844,8 @@ static const struct of_device_id ingenic_drm_of_match[] = { { /* sentinel */ }, };
+MODULE_DEVICE_TABLE(of, ingenic_drm_of_match);
Please remove the blank line above the MODULE_DEVICE_TABLE() macro.
-Paul
static struct platform_driver ingenic_drm_driver = { .driver = { .name = "ingenic-drm", -- 2.23.0
Am 02.03.2020 um 20:21 schrieb Paul Cercueil paul@crapouillou.net:
Hi Nikolaus,
Le ven., févr. 28, 2020 at 19:19, H. Nikolaus Schaller hns@goldelico.com a écrit :
so that the driver can load by matching the device tree if compiled as module. Signed-off-by: H. Nikolaus Schaller hns@goldelico.com
drivers/gpu/drm/ingenic/ingenic-drm.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/gpu/drm/ingenic/ingenic-drm.c b/drivers/gpu/drm/ingenic/ingenic-drm.c index 6d47ef7b148c..d8617096dd8e 100644 --- a/drivers/gpu/drm/ingenic/ingenic-drm.c +++ b/drivers/gpu/drm/ingenic/ingenic-drm.c @@ -844,6 +844,8 @@ static const struct of_device_id ingenic_drm_of_match[] = { { /* sentinel */ }, }; +MODULE_DEVICE_TABLE(of, ingenic_drm_of_match);
Please remove the blank line above the MODULE_DEVICE_TABLE() macro.
Ok.
-Paul
static struct platform_driver ingenic_drm_driver = { .driver = { .name = "ingenic-drm", -- 2.23.0
From: Paul Boddie paul@boddie.org.uk
A specialisation of the generic Synopsys HDMI driver is employed for JZ4780 HDMI support. This requires a new driver, plus device tree and configuration modifications.
Signed-off-by: Paul Boddie paul@boddie.org.uk Signed-off-by: H. Nikolaus Schaller hns@goldelico.com --- drivers/gpu/drm/ingenic/Kconfig | 8 ++ drivers/gpu/drm/ingenic/Makefile | 1 + drivers/gpu/drm/ingenic/dw_hdmi-jz4780.c | 120 +++++++++++++++++++++++ 3 files changed, 129 insertions(+) create mode 100644 drivers/gpu/drm/ingenic/dw_hdmi-jz4780.c
diff --git a/drivers/gpu/drm/ingenic/Kconfig b/drivers/gpu/drm/ingenic/Kconfig index d82c3d37ec9c..44bfd0d35af1 100644 --- a/drivers/gpu/drm/ingenic/Kconfig +++ b/drivers/gpu/drm/ingenic/Kconfig @@ -14,3 +14,11 @@ config DRM_INGENIC Choose this option for DRM support for the Ingenic SoCs.
If M is selected the module will be called ingenic-drm. + +config DRM_DW_HDMI_JZ4780 + tristate "HDMI Support for Ingenic JZ4780" + depends on DRM_INGENIC + depends on OF + select DRM_DW_HDMI + help + Choose this option for HDMI output from the Ingenic JZ4780. diff --git a/drivers/gpu/drm/ingenic/Makefile b/drivers/gpu/drm/ingenic/Makefile index 11cac42ce0bb..238383de63c7 100644 --- a/drivers/gpu/drm/ingenic/Makefile +++ b/drivers/gpu/drm/ingenic/Makefile @@ -1 +1,2 @@ obj-$(CONFIG_DRM_INGENIC) += ingenic-drm.o +obj-$(CONFIG_DRM_DW_HDMI_JZ4780) += dw_hdmi-jz4780.o diff --git a/drivers/gpu/drm/ingenic/dw_hdmi-jz4780.c b/drivers/gpu/drm/ingenic/dw_hdmi-jz4780.c new file mode 100644 index 000000000000..fa379e337263 --- /dev/null +++ b/drivers/gpu/drm/ingenic/dw_hdmi-jz4780.c @@ -0,0 +1,120 @@ +// SPDX-License-Identifier: GPL-2.0 +/* Copyright (C) 2011-2013 Freescale Semiconductor, Inc. + * Copyright (C) 2019 Paul Boddie paul@boddie.org.uk + * + * Derived from dw_hdmi-imx.c with i.MX portions removed. + * Probe and remove operations derived from rcar_dw_hdmi.c. + */ + +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/regmap.h> + +#include <drm/bridge/dw_hdmi.h> +#include <drm/drm_of.h> + +static const struct dw_hdmi_mpll_config jz4780_mpll_cfg[] = { + { 45250000, { { 0x01e0, 0x0000 }, + { 0x21e1, 0x0000 }, + { 0x41e2, 0x0000 } } }, + { 92500000, { { 0x0140, 0x0005 }, + { 0x2141, 0x0005 }, + { 0x4142, 0x0005 } } }, + { 148500000, { { 0x00a0, 0x000a }, + { 0x20a1, 0x000a }, + { 0x40a2, 0x000a } } }, + { 216000000, { { 0x00a0, 0x000a }, + { 0x2001, 0x000f }, + { 0x4002, 0x000f } } }, + { ~0UL, { { 0x0000, 0x0000 }, + { 0x0000, 0x0000 }, + { 0x0000, 0x0000 } } } +}; + +static const struct dw_hdmi_curr_ctrl jz4780_cur_ctr[] = { + /*pixelclk bpp8 bpp10 bpp12 */ + { 54000000, { 0x091c, 0x091c, 0x06dc } }, + { 58400000, { 0x091c, 0x06dc, 0x06dc } }, + { 72000000, { 0x06dc, 0x06dc, 0x091c } }, + { 74250000, { 0x06dc, 0x0b5c, 0x091c } }, + { 118800000, { 0x091c, 0x091c, 0x06dc } }, + { 216000000, { 0x06dc, 0x0b5c, 0x091c } }, + { ~0UL, { 0x0000, 0x0000, 0x0000 } }, +}; + +/* + * Resistance term 133Ohm Cfg + * PREEMP config 0.00 + * TX/CK level 10 + */ +static const struct dw_hdmi_phy_config jz4780_phy_config[] = { + /*pixelclk symbol term vlev */ + { 216000000, 0x800d, 0x0005, 0x01ad}, + { ~0UL, 0x0000, 0x0000, 0x0000} +}; + +static enum drm_mode_status +jz4780_hdmi_mode_valid(struct drm_connector *con, + const struct drm_display_mode *mode) +{ + if (mode->clock < 13500) + return MODE_CLOCK_LOW; + /* FIXME: Hardware is capable of 270MHz, but setup data is missing. */ + if (mode->clock > 216000) + return MODE_CLOCK_HIGH; + + return MODE_OK; +} + +static struct dw_hdmi_plat_data jz4780_dw_hdmi_plat_data = { + .mpll_cfg = jz4780_mpll_cfg, + .cur_ctr = jz4780_cur_ctr, + .phy_config = jz4780_phy_config, + .mode_valid = jz4780_hdmi_mode_valid, +}; + +static const struct of_device_id jz4780_dw_hdmi_dt_ids[] = { + { .compatible = "ingenic,jz4780-dw-hdmi" }, + { /* Sentinel */ }, +}; +MODULE_DEVICE_TABLE(of, jz4780_dw_hdmi_dt_ids); + +static int jz4780_dw_hdmi_probe(struct platform_device *pdev) +{ + struct dw_hdmi *hdmi; + + hdmi = dw_hdmi_probe(pdev, &jz4780_dw_hdmi_plat_data); + if (IS_ERR(hdmi)) + return PTR_ERR(hdmi); + + platform_set_drvdata(pdev, hdmi); + + return 0; +} + +static int jz4780_dw_hdmi_remove(struct platform_device *pdev) +{ + struct dw_hdmi *hdmi = platform_get_drvdata(pdev); + + dw_hdmi_remove(hdmi); + + return 0; +} + +static struct platform_driver jz4780_dw_hdmi_platform_driver = { + .probe = jz4780_dw_hdmi_probe, + .remove = jz4780_dw_hdmi_remove, + .driver = { + .name = "dw-hdmi-jz4780", + .of_match_table = jz4780_dw_hdmi_dt_ids, + }, +}; + +module_platform_driver(jz4780_dw_hdmi_platform_driver); + +MODULE_AUTHOR("Andy Yan andy.yan@rock-chips.com"); +MODULE_AUTHOR("Yakir Yang ykk@rock-chips.com"); +MODULE_AUTHOR("Paul Boddie paul@boddie.org.uk"); +MODULE_DESCRIPTION("Ingenic JZ4780 DW-HDMI Driver Extension"); +MODULE_LICENSE("GPL"); +MODULE_ALIAS("platform:dw-hdmi-jz4780");
From: Paul Boddie paul@boddie.org.uk
Signed-off-by: Paul Boddie paul@boddie.org.uk Signed-off-by: H. Nikolaus Schaller hns@goldelico.com --- drivers/pinctrl/pinctrl-ingenic.c | 7 +++++++ 1 file changed, 7 insertions(+)
diff --git a/drivers/pinctrl/pinctrl-ingenic.c b/drivers/pinctrl/pinctrl-ingenic.c index 96f04d121ebd..1599a003c31f 100644 --- a/drivers/pinctrl/pinctrl-ingenic.c +++ b/drivers/pinctrl/pinctrl-ingenic.c @@ -4,6 +4,7 @@ * * Copyright (c) 2017 Paul Cercueil paul@crapouillou.net * Copyright (c) 2019 周琰杰 (Zhou Yanjie) zhouyanjie@wanyeetech.com + * Copyright (c) 2017, 2019 Paul Boddie paul@boddie.org.uk */
#include <linux/compiler.h> @@ -900,6 +901,7 @@ static int jz4780_mmc0_8bit_a_pins[] = { 0x04, 0x05, 0x06, 0x07, 0x18, }; static int jz4780_i2c3_pins[] = { 0x6a, 0x6b, }; static int jz4780_i2c4_e_pins[] = { 0x8c, 0x8d, }; static int jz4780_i2c4_f_pins[] = { 0xb9, 0xb8, }; +static int jz4780_hdmi_ddc_pins[] = { 0xb9, 0xb8, };
static int jz4780_uart2_data_funcs[] = { 1, 1, }; static int jz4780_uart2_hwflow_funcs[] = { 1, 1, }; @@ -908,6 +910,7 @@ static int jz4780_mmc0_8bit_a_funcs[] = { 1, 1, 1, 1, 1, }; static int jz4780_i2c3_funcs[] = { 1, 1, }; static int jz4780_i2c4_e_funcs[] = { 1, 1, }; static int jz4780_i2c4_f_funcs[] = { 1, 1, }; +static int jz4780_hdmi_ddc_funcs[] = { 0, 0, };
static const struct group_desc jz4780_groups[] = { INGENIC_PIN_GROUP("uart0-data", jz4770_uart0_data), @@ -950,6 +953,7 @@ static const struct group_desc jz4780_groups[] = { INGENIC_PIN_GROUP("i2c3-data", jz4780_i2c3), INGENIC_PIN_GROUP("i2c4-data-e", jz4780_i2c4_e), INGENIC_PIN_GROUP("i2c4-data-f", jz4780_i2c4_f), + INGENIC_PIN_GROUP("hdmi-ddc", jz4780_hdmi_ddc), INGENIC_PIN_GROUP("cim-data", jz4770_cim_8bit), INGENIC_PIN_GROUP("lcd-24bit", jz4770_lcd_24bit), { "lcd-no-pins", }, @@ -982,6 +986,7 @@ static const char *jz4780_nemc_groups[] = { static const char *jz4780_i2c3_groups[] = { "i2c3-data", }; static const char *jz4780_i2c4_groups[] = { "i2c4-data-e", "i2c4-data-f", }; static const char *jz4780_cim_groups[] = { "cim-data", }; +static const char *jz4780_hdmi_ddc_groups[] = { "hdmi-ddc", };
static const struct function_desc jz4780_functions[] = { { "uart0", jz4770_uart0_groups, ARRAY_SIZE(jz4770_uart0_groups), }, @@ -1014,6 +1019,8 @@ static const struct function_desc jz4780_functions[] = { { "pwm5", jz4770_pwm5_groups, ARRAY_SIZE(jz4770_pwm5_groups), }, { "pwm6", jz4770_pwm6_groups, ARRAY_SIZE(jz4770_pwm6_groups), }, { "pwm7", jz4770_pwm7_groups, ARRAY_SIZE(jz4770_pwm7_groups), }, + { "hdmi-ddc", jz4780_hdmi_ddc_groups, + ARRAY_SIZE(jz4780_hdmi_ddc_groups), }, };
static const struct ingenic_chip_info jz4780_chip_info = {
On Fri, Feb 28, 2020 at 7:19 PM H. Nikolaus Schaller hns@goldelico.com wrote:
From: Paul Boddie paul@boddie.org.uk
Signed-off-by: Paul Boddie paul@boddie.org.uk Signed-off-by: H. Nikolaus Schaller hns@goldelico.com
This looks good, can I just apply this to the pinctrl tree?
Yours, Linus Walleij
Am 28.02.2020 um 23:05 schrieb Linus Walleij linus.walleij@linaro.org:
On Fri, Feb 28, 2020 at 7:19 PM H. Nikolaus Schaller hns@goldelico.com wrote:
From: Paul Boddie paul@boddie.org.uk
Signed-off-by: Paul Boddie paul@boddie.org.uk Signed-off-by: H. Nikolaus Schaller hns@goldelico.com
This looks good, can I just apply this to the pinctrl tree?
Yes. It is more or less a base commit for the others.
Yours, Linus Walleij
BR and thanks, Nikolaus
On Fri, Feb 28, 2020 at 7:19 PM H. Nikolaus Schaller hns@goldelico.com wrote:
From: Paul Boddie paul@boddie.org.uk
Signed-off-by: Paul Boddie paul@boddie.org.uk Signed-off-by: H. Nikolaus Schaller hns@goldelico.com
Patch applied to the pinctrl tree, it should be fine to merge the rest of the patches in another tree since there are no compile-time dependencies.
Yours, Linus Walleij
From: Paul Boddie paul@boddie.org.uk
A specialisation of the generic Synopsys HDMI driver is employed for JZ4780 HDMI support. This requires a new driver, plus device tree and configuration modifications.
Signed-off-by: Paul Boddie paul@boddie.org.uk Signed-off-by: H. Nikolaus Schaller hns@goldelico.com --- arch/mips/boot/dts/ingenic/jz4780.dtsi | 32 ++++++++++++++++++++++++++ 1 file changed, 32 insertions(+)
diff --git a/arch/mips/boot/dts/ingenic/jz4780.dtsi b/arch/mips/boot/dts/ingenic/jz4780.dtsi index f928329b034b..391d4e1efd35 100644 --- a/arch/mips/boot/dts/ingenic/jz4780.dtsi +++ b/arch/mips/boot/dts/ingenic/jz4780.dtsi @@ -433,4 +433,36 @@
status = "disabled"; }; + + hdmi: hdmi@10180000 { + compatible = "ingenic,jz4780-dw-hdmi"; + reg = <0x10180000 0x8000>; + reg-io-width = <4>; + + clocks = <&cgu JZ4780_CLK_HDMI>, <&cgu JZ4780_CLK_AHB0>; + clock-names = "isfr" , "iahb"; + + assigned-clocks = <&cgu JZ4780_CLK_HDMI>; + assigned-clock-rates = <27000000>; + + interrupt-parent = <&intc>; + interrupts = <3>; + + /* ddc-i2c-bus = <&i2c4>; */ + + status = "disabled"; + }; + + lcd: lcd@13050000 { + compatible = "ingenic,jz4740-lcd"; + reg = <0x13050000 0x1800>; + + clocks = <&cgu JZ4780_CLK_TVE>, <&cgu JZ4780_CLK_LCD0PIXCLK>; + clock-names = "lcd", "lcd_pclk"; + + interrupt-parent = <&intc>; + interrupts = <31>; + + status = "disabled"; + }; };
Hi Nikolaus,
Le ven., févr. 28, 2020 at 19:19, H. Nikolaus Schaller hns@goldelico.com a écrit :
From: Paul Boddie paul@boddie.org.uk
A specialisation of the generic Synopsys HDMI driver is employed for JZ4780 HDMI support. This requires a new driver, plus device tree and configuration modifications.
Signed-off-by: Paul Boddie paul@boddie.org.uk Signed-off-by: H. Nikolaus Schaller hns@goldelico.com
arch/mips/boot/dts/ingenic/jz4780.dtsi | 32 ++++++++++++++++++++++++++ 1 file changed, 32 insertions(+)
diff --git a/arch/mips/boot/dts/ingenic/jz4780.dtsi b/arch/mips/boot/dts/ingenic/jz4780.dtsi index f928329b034b..391d4e1efd35 100644 --- a/arch/mips/boot/dts/ingenic/jz4780.dtsi +++ b/arch/mips/boot/dts/ingenic/jz4780.dtsi @@ -433,4 +433,36 @@
status = "disabled";};
- hdmi: hdmi@10180000 {
compatible = "ingenic,jz4780-dw-hdmi";reg = <0x10180000 0x8000>;reg-io-width = <4>;clocks = <&cgu JZ4780_CLK_HDMI>, <&cgu JZ4780_CLK_AHB0>;clock-names = "isfr" , "iahb";assigned-clocks = <&cgu JZ4780_CLK_HDMI>;assigned-clock-rates = <27000000>;
I *think* this should go to the board file.
interrupt-parent = <&intc>;interrupts = <3>;/* ddc-i2c-bus = <&i2c4>; */status = "disabled";- };
- lcd: lcd@13050000 {
The node name should be 'lcd-controller'.
compatible = "ingenic,jz4740-lcd";
The JZ4780's LCD controller is much newer than the JZ4740 one, so even if it works with the "ingenic,jz4740-lcd" compatible string, you want it as a fallback. So this should be: compatible = "ingenic,jz4780-lcd", "ingenic,jz4740-lcd".
That means the YAML should be updated too.
-Paul
reg = <0x13050000 0x1800>;clocks = <&cgu JZ4780_CLK_TVE>, <&cgu JZ4780_CLK_LCD0PIXCLK>;clock-names = "lcd", "lcd_pclk";interrupt-parent = <&intc>;interrupts = <31>;status = "disabled";- };
};
2.23.0
Hi Paul,
Am 02.03.2020 um 20:27 schrieb Paul Cercueil paul@crapouillou.net:
Hi Nikolaus,
Le ven., févr. 28, 2020 at 19:19, H. Nikolaus Schaller hns@goldelico.com a écrit :
From: Paul Boddie paul@boddie.org.uk A specialisation of the generic Synopsys HDMI driver is employed for JZ4780 HDMI support. This requires a new driver, plus device tree and configuration modifications. Signed-off-by: Paul Boddie paul@boddie.org.uk Signed-off-by: H. Nikolaus Schaller hns@goldelico.com
arch/mips/boot/dts/ingenic/jz4780.dtsi | 32 ++++++++++++++++++++++++++ 1 file changed, 32 insertions(+) diff --git a/arch/mips/boot/dts/ingenic/jz4780.dtsi b/arch/mips/boot/dts/ingenic/jz4780.dtsi index f928329b034b..391d4e1efd35 100644 --- a/arch/mips/boot/dts/ingenic/jz4780.dtsi +++ b/arch/mips/boot/dts/ingenic/jz4780.dtsi @@ -433,4 +433,36 @@ status = "disabled"; };
- hdmi: hdmi@10180000 {
compatible = "ingenic,jz4780-dw-hdmi";reg = <0x10180000 0x8000>;reg-io-width = <4>;clocks = <&cgu JZ4780_CLK_HDMI>, <&cgu JZ4780_CLK_AHB0>;clock-names = "isfr" , "iahb";assigned-clocks = <&cgu JZ4780_CLK_HDMI>;assigned-clock-rates = <27000000>;I *think* this should go to the board file.
Hm. I am not sure.
Can there be differences in HDMI between different boards so that it needs to be defined there?
IMHO the HDMI subsystem is completely sitting on the jz4780 SoC and clocked by the master clock. So boards should only differ in the ESD protection and mechanical connector...
And status = "ok".
interrupt-parent = <&intc>;interrupts = <3>;/* ddc-i2c-bus = <&i2c4>; */status = "disabled";- };
- lcd: lcd@13050000 {
The node name should be 'lcd-controller'.
compatible = "ingenic,jz4740-lcd";The JZ4780's LCD controller is much newer than the JZ4740 one, so even if it works with the "ingenic,jz4740-lcd" compatible string, you want it as a fallback. So this should be: compatible = "ingenic,jz4780-lcd", "ingenic,jz4740-lcd".
Ah, that is an interesting detail.
It could be the reason why the HDMI does not show an output signal yet. If the jz4740-lcd and jz4780-lcd are not really 100% compatible. I'll give it try asap.
If it does not help to get output signals, we need community members who can test (i.e. own an CI20 board) and can help to identify the bug(s).
That means the YAML should be updated too.
Ok.
BR, Nikolaus
-Paul
reg = <0x13050000 0x1800>;clocks = <&cgu JZ4780_CLK_TVE>, <&cgu JZ4780_CLK_LCD0PIXCLK>;clock-names = "lcd", "lcd_pclk";interrupt-parent = <&intc>;interrupts = <31>;status = "disabled";- };
};
2.23.0
Hi Paul,
Am 02.03.2020 um 20:27 schrieb Paul Cercueil paul@crapouillou.net:
Hi Nikolaus,
Le ven., févr. 28, 2020 at 19:19, H. Nikolaus Schaller hns@goldelico.com a écrit :
From: Paul Boddie paul@boddie.org.uk A specialisation of the generic Synopsys HDMI driver is employed for JZ4780 HDMI support. This requires a new driver, plus device tree and configuration modifications. Signed-off-by: Paul Boddie paul@boddie.org.uk Signed-off-by: H. Nikolaus Schaller hns@goldelico.com
arch/mips/boot/dts/ingenic/jz4780.dtsi | 32 ++++++++++++++++++++++++++ 1 file changed, 32 insertions(+) diff --git a/arch/mips/boot/dts/ingenic/jz4780.dtsi b/arch/mips/boot/dts/ingenic/jz4780.dtsi index f928329b034b..391d4e1efd35 100644 --- a/arch/mips/boot/dts/ingenic/jz4780.dtsi +++ b/arch/mips/boot/dts/ingenic/jz4780.dtsi @@ -433,4 +433,36 @@ status = "disabled"; };
- hdmi: hdmi@10180000 {
compatible = "ingenic,jz4780-dw-hdmi";reg = <0x10180000 0x8000>;reg-io-width = <4>;clocks = <&cgu JZ4780_CLK_HDMI>, <&cgu JZ4780_CLK_AHB0>;clock-names = "isfr" , "iahb";assigned-clocks = <&cgu JZ4780_CLK_HDMI>;assigned-clock-rates = <27000000>;I *think* this should go to the board file.
interrupt-parent = <&intc>;interrupts = <3>;/* ddc-i2c-bus = <&i2c4>; */status = "disabled";- };
- lcd: lcd@13050000 {
The node name should be 'lcd-controller'.
compatible = "ingenic,jz4740-lcd";The JZ4780's LCD controller is much newer than the JZ4740 one, so even if it works with the "ingenic,jz4740-lcd" compatible string, you want it as a fallback. So this should be: compatible = "ingenic,jz4780-lcd", "ingenic,jz4740-lcd".
That means the YAML should be updated too.
I have started to look into jz4780 HDMI setup again.
Well, there is no driver compatible to "ingenic,jz4780-lcd" so far and it is questionalbe if we need a different one.
I think we should rather make the driver also compatible than adding a fallback to ingenic,jz4740-lcdto the DTS.
The reason why this is better even if both LCDC are almost compatible is that the jz4780 allows for much bigger displays and therefore should have its own jz_soc_info with 4k x 2k as maximum.
Next I tried to find out if the LCDC are really compatible.
Well the jz4780 has two lcdc instances but they are separated by the reg addr. Next, there are unique features (like picture in picture with alpha blending) but those are probably disabled if not programmed from reset state. This may become a reason to separate or augment the driver for the jz4780 but at the moment we can ignore that.
There are also subtly different bit definitions and register widths (e.g. 24 bit in addition to 16/18 bit modes or more bits for the sync position) but it looks as if the ingenic_drm driver already handles this.
Then I tried to read back the registers. Strangely they are all 0x00000000. So there is no programming of the lcd-controller in our DT setup with HDMI at all!
I also checked that ingenic_drm_probe() is called and returns successfully 0. It also reports that a /dev/fb has been created:
[ 7.908830] ingenic-drm 13050000.lcd-controller: fb0: ingenic-drmdrmf frame buffer device
But for example ingenic_drm_encoder_atomic_mode_set() is never called which should write some registers of the LCDC.
I only did see some calls to ingenic_drm_encoder_atomic_check().
This of course explains why we have no HDMI signals despite proper HPD and a /dev/fb0. Because the LCDC is not being programmed.
Any ideas / hints how to check or improve?
BR and thanks, Nikolaus
Hi Nikolaus,
Le mer., mars 11, 2020 at 13:43, H. Nikolaus Schaller hns@goldelico.com a écrit :
Hi Paul,
Am 02.03.2020 um 20:27 schrieb Paul Cercueil paul@crapouillou.net:
Hi Nikolaus,
Le ven., févr. 28, 2020 at 19:19, H. Nikolaus Schaller hns@goldelico.com a écrit :
From: Paul Boddie paul@boddie.org.uk A specialisation of the generic Synopsys HDMI driver is employed for JZ4780 HDMI support. This requires a new driver, plus device tree and configuration modifications. Signed-off-by: Paul Boddie paul@boddie.org.uk Signed-off-by: H. Nikolaus Schaller hns@goldelico.com
arch/mips/boot/dts/ingenic/jz4780.dtsi | 32 ++++++++++++++++++++++++++ 1 file changed, 32 insertions(+) diff --git a/arch/mips/boot/dts/ingenic/jz4780.dtsi b/arch/mips/boot/dts/ingenic/jz4780.dtsi index f928329b034b..391d4e1efd35 100644 --- a/arch/mips/boot/dts/ingenic/jz4780.dtsi +++ b/arch/mips/boot/dts/ingenic/jz4780.dtsi @@ -433,4 +433,36 @@ status = "disabled"; };
- hdmi: hdmi@10180000 {
compatible = "ingenic,jz4780-dw-hdmi";reg = <0x10180000 0x8000>;reg-io-width = <4>;clocks = <&cgu JZ4780_CLK_HDMI>, <&cgu JZ4780_CLK_AHB0>;clock-names = "isfr" , "iahb";assigned-clocks = <&cgu JZ4780_CLK_HDMI>;assigned-clock-rates = <27000000>;I *think* this should go to the board file.
interrupt-parent = <&intc>;interrupts = <3>;/* ddc-i2c-bus = <&i2c4>; */status = "disabled";- };
- lcd: lcd@13050000 {
The node name should be 'lcd-controller'.
compatible = "ingenic,jz4740-lcd";The JZ4780's LCD controller is much newer than the JZ4740 one, so even if it works with the "ingenic,jz4740-lcd" compatible string, you want it as a fallback. So this should be: compatible = "ingenic,jz4780-lcd", "ingenic,jz4740-lcd".
That means the YAML should be updated too.
I have started to look into jz4780 HDMI setup again.
Well, there is no driver compatible to "ingenic,jz4780-lcd" so far and it is questionalbe if we need a different one.
I think we should rather make the driver also compatible than adding a fallback to ingenic,jz4740-lcdto the DTS.
The reason why this is better even if both LCDC are almost compatible is that the jz4780 allows for much bigger displays and therefore should have its own jz_soc_info with 4k x 2k as maximum.
Sure, feel free to extend the driver.
Next I tried to find out if the LCDC are really compatible.
Well the jz4780 has two lcdc instances but they are separated by the reg addr. Next, there are unique features (like picture in picture with alpha blending) but those are probably disabled if not programmed from reset state. This may become a reason to separate or augment the driver for the jz4780 but at the moment we can ignore that.
Two LCDC instances -> two lcd-controller@... nodes. It's that simple.
The other features you listed are outside the LCDC, so outside the scope of this driver.
There are also subtly different bit definitions and register widths (e.g. 24 bit in addition to 16/18 bit modes or more bits for the sync position) but it looks as if the ingenic_drm driver already handles this.
Then I tried to read back the registers. Strangely they are all 0x00000000. So there is no programming of the lcd-controller in our DT setup with HDMI at all!
How did you read them? Do it from the regmap: should be "cat /sys/kernel/debug/regmap/13050000.lcd-controller/registers" (not sure about the path)
I also checked that ingenic_drm_probe() is called and returns successfully 0. It also reports that a /dev/fb has been created:
[ 7.908830] ingenic-drm 13050000.lcd-controller: fb0: ingenic-drmdrmf frame buffer device
But for example ingenic_drm_encoder_atomic_mode_set() is never called which should write some registers of the LCDC.
I only did see some calls to ingenic_drm_encoder_atomic_check().
This of course explains why we have no HDMI signals despite proper HPD and a /dev/fb0. Because the LCDC is not being programmed.
It won't be called until the HDMI driver says that the cable is plugged, and there's a client application (e.g. fbdev emulation) running. So the problem is most likely within the HDMI driver.
Cheers, -Paul
Any ideas / hints how to check or improve?
BR and thanks, Nikolaus
Hi Paul,
Am 11.03.2020 um 14:20 schrieb Paul Cercueil paul@crapouillou.net:
Hi Nikolaus,
Le mer., mars 11, 2020 at 13:43, H. Nikolaus Schaller hns@goldelico.com a écrit :
Hi Paul,
The JZ4780's LCD controller is much newer than the JZ4740 one, so even if it works with the "ingenic,jz4740-lcd" compatible string, you want it as a fallback. So this should be: compatible = "ingenic,jz4780-lcd", "ingenic,jz4740-lcd". That means the YAML should be updated too.
I have started to look into jz4780 HDMI setup again. Well, there is no driver compatible to "ingenic,jz4780-lcd" so far and it is questionalbe if we need a different one. I think we should rather make the driver also compatible than adding a fallback to ingenic,jz4740-lcdto the DTS. The reason why this is better even if both LCDC are almost compatible is that the jz4780 allows for much bigger displays and therefore should have its own jz_soc_info with 4k x 2k as maximum.
Sure, feel free to extend the driver.
Next I tried to find out if the LCDC are really compatible. Well the jz4780 has two lcdc instances but they are separated by the reg addr. Next, there are unique features (like picture in picture with alpha blending) but those are probably disabled if not programmed from reset state. This may become a reason to separate or augment the driver for the jz4780 but at the moment we can ignore that.
Two LCDC instances -> two lcd-controller@... nodes. It's that simple.
Indeed :)
The other features you listed are outside the LCDC, so outside the scope of this driver.
Well, in the description they are mixed but I think we do not have to care about now.
There are also subtly different bit definitions and register widths (e.g. 24 bit in addition to 16/18 bit modes or more bits for the sync position) but it looks as if the ingenic_drm driver already handles this. Then I tried to read back the registers. Strangely they are all 0x00000000. So there is no programming of the lcd-controller in our DT setup with HDMI at all!
How did you read them?
I used devmem2 (may be an omap tool I have recompiled for MIPS - it uses /dev/mem).
Do it from the regmap: should be "cat /sys/kernel/debug/regmap/13050000.lcd-controller/registers" (not sure about the path)
Well seems to give the same result:
root@letux:~# cat /sys/kernel/debug/regmap/13050000.lcd-controller/registers 00: 00000000 04: 00000000 08: 00000000 0c: 00000000 10: 00000000 14: 00000000 18: 00000000 1c: 00000000 20: 00000000 24: 00000000 28: 00000000 2c: 00000000 30: 00000000 34: 00000000 38: 00000000 3c: 00000000 40: 00000000 44: 00000000 48: 00000000 4c: 00000000 50: 00000000 54: 00000000 58: 00000000 5c: 00000000 root@letux:~#
I also checked that ingenic_drm_probe() is called and returns successfully 0. It also reports that a /dev/fb has been created: [ 7.908830] ingenic-drm 13050000.lcd-controller: fb0: ingenic-drmdrmf frame buffer device But for example ingenic_drm_encoder_atomic_mode_set() is never called which should write some registers of the LCDC. I only did see some calls to ingenic_drm_encoder_atomic_check(). This of course explains why we have no HDMI signals despite proper HPD and a /dev/fb0. Because the LCDC is not being programmed.
It won't be called until the HDMI driver says that the cable is plugged, and there's a client application (e.g. fbdev emulation) running. So the problem is most likely within the HDMI driver.
Ok!
The HDMI subsystem says (with some printk inserted) on cable unplug/replug:
root@letux:~# [ 3894.370706] dw_hdmi_update_power [ 3894.373984] dw_hdmi_update_power: hdmi->force=0 [ 3894.378759] dw_hdmi_update_power: hdmi->disabled=0 [ 3894.383756] dw_hdmi_update_power: hdmi->bridge_is_on=1 [ 3894.388947] dw_hdmi_update_power: hdmi->rxsense=1 [ 3894.393831] dw_hdmi_update_power: force=2 [ 3894.397895] dw_hdmi_update_power: hdmi->bridge_is_on=1 [ 3894.403200] dw_hdmi_phy_update_hpd [ 3894.406784] dw_hdmi_update_power [ 3894.410054] dw_hdmi_update_power: hdmi->force=0 [ 3894.414766] dw_hdmi_update_power: hdmi->disabled=0 [ 3894.419611] dw_hdmi_update_power: hdmi->bridge_is_on=1 [ 3894.424928] dw_hdmi_update_power: hdmi->rxsense=1 [ 3894.429699] dw_hdmi_update_power: force=2 [ 3894.433876] dw_hdmi_update_power: hdmi->bridge_is_on=1 [ 3894.439068] dw_hdmi_phy_update_hpd [ 3894.452316] dw_hdmi_update_power [ 3894.455596] dw_hdmi_update_power: hdmi->force=0 [ 3894.460150] dw_hdmi_update_power: hdmi->disabled=0 [ 3894.464967] dw_hdmi_update_power: hdmi->bridge_is_on=1 [ 3894.470131] dw_hdmi_update_power: hdmi->rxsense=1 [ 3894.475051] dw_hdmi_update_power: force=2 [ 3894.479111] dw_hdmi_update_power: hdmi->bridge_is_on=1 [ 3894.484423] dw_hdmi_phy_update_hpd [ 3894.488007] dw_hdmi_update_power [ 3894.491278] dw_hdmi_update_power: hdmi->force=0 [ 3894.495982] dw_hdmi_update_power: hdmi->disabled=0 [ 3894.500823] dw_hdmi_update_power: hdmi->bridge_is_on=1 [ 3894.506139] dw_hdmi_update_power: hdmi->rxsense=0 [ 3894.510895] dw_hdmi_update_power: force=1 [ 3894.515063] dw_hdmi_update_power: hdmi->bridge_is_on=1 [ 3894.520252] dw_hdmi_poweroff [ 3894.523284] dw_hdmi_phy_disable [ 3894.526480] dw_hdmi_phy_power_off [ 3894.529823] dw_hdmi_phy_gen2_txpwron [ 3894.533567] dw-hdmi-jz4780 10180000.hdmi: PHY powered down in 0 iterations [ 3894.540496] dw_hdmi_phy_gen2_pddq [ 3894.543966] dw_hdmi_phy_update_hpd [ 3894.547435] dw-hdmi-jz4780 10180000.hdmi: EVENT=plugout [ 3897.079560] dw_hdmi_update_power [ 3897.082840] dw_hdmi_update_power: hdmi->force=0 [ 3897.087394] dw_hdmi_update_power: hdmi->disabled=0 [ 3897.092207] dw_hdmi_update_power: hdmi->bridge_is_on=0 [ 3897.097370] dw_hdmi_update_power: hdmi->rxsense=1 [ 3897.102316] dw_hdmi_update_power: force=2 [ 3897.106380] dw_hdmi_update_power: hdmi->bridge_is_on=0 [ 3897.111667] dw_hdmi_poweron [ 3897.114518] dw_hdmi_setup [ 3897.117163] hdmi_disable_overflow_interrupts [ 3897.121478] dw-hdmi-jz4780 10180000.hdmi: Non-CEA mode used in HDMI [ 3897.127930] hdmi_av_composer [ 3897.130848] dw-hdmi-jz4780 10180000.hdmi: final pixclk = 0 [ 3897.136506] dw_hdmi_phy_init [ 3897.139440] dw_hdmi_phy_sel_data_en_pol [ 3897.143428] dw_hdmi_phy_sel_interface_control [ 3897.147840] hdmi_phy_configure [ 3897.150922] dw_hdmi_phy_power_off [ 3897.154415] dw_hdmi_phy_gen2_txpwron [ 3897.158043] dw-hdmi-jz4780 10180000.hdmi: PHY powered down in 0 iterations [ 3897.165094] dw_hdmi_phy_gen2_pddq [ 3897.168468] dw_hdmi_set_high_tmds_clock_ratio [ 3897.173002] hdmi_phy_configure_dwc_hdmi_3d_tx [ 3897.186578] dw_hdmi_phy_power_on [ 3897.189847] dw_hdmi_phy_gen2_txpwron [ 3897.193586] dw_hdmi_phy_gen2_pddq [ 3897.217640] dw-hdmi-jz4780 10180000.hdmi: PHY PLL locked 1 iterations [ 3897.224226] dw_hdmi_phy_sel_data_en_pol [ 3897.228107] dw_hdmi_phy_sel_interface_control [ 3897.232631] hdmi_phy_configure [ 3897.235739] dw_hdmi_phy_power_off [ 3897.239082] dw_hdmi_phy_gen2_txpwron [ 3897.242826] dw-hdmi-jz4780 10180000.hdmi: PHY powered down in 0 iterations [ 3897.249754] dw_hdmi_phy_gen2_pddq [ 3897.253239] dw_hdmi_set_high_tmds_clock_ratio [ 3897.257658] hdmi_phy_configure_dwc_hdmi_3d_tx [ 3897.271264] dw_hdmi_phy_power_on [ 3897.274659] dw_hdmi_phy_gen2_txpwron [ 3897.278292] dw_hdmi_phy_gen2_pddq [ 3897.283840] dw-hdmi-jz4780 10180000.hdmi: PHY PLL locked 1 iterations [ 3897.290346] dw_hdmi_enable_video_path [ 3897.294240] dw-hdmi-jz4780 10180000.hdmi: sink has audio support [ 3897.300324] dw-hdmi-jz4780 10180000.hdmi: dw_hdmi_setup HDMI mode [ 3897.306596] hdmi_config_AVI [ 3897.309467] hdmi_config_vendor_specific_infoframe [ 3897.314336] hdmi_config_drm_infoframe [ 3897.318096] hdmi_tx_hdcp_config [ 3897.321270] dw_hdmi_clear_overflow [ 3897.324831] dw_hdmi_phy_update_hpd [ 3897.328298] dw-hdmi-jz4780 10180000.hdmi: EVENT=plugin [ 3897.333704] dw_hdmi_update_power [ 3897.336990] dw_hdmi_update_power: hdmi->force=0 [ 3897.341551] dw_hdmi_update_power: hdmi->disabled=0 [ 3897.346528] dw_hdmi_update_power: hdmi->bridge_is_on=1 [ 3897.351858] dw_hdmi_update_power: hdmi->rxsense=1 [ 3897.356615] dw_hdmi_update_power: force=2 [ 3897.360655] dw_hdmi_update_power: hdmi->bridge_is_on=1 [ 3897.365980] dw_hdmi_phy_update_hpd
So the plugout/plugin events are not processed further.
One thing looks strange:
[ 3897.127930] hdmi_av_composer [ 3897.130848] dw-hdmi-jz4780 10180000.hdmi: final pixclk = 0
But I have no idea if this is the reason or the consequence of the uninitialized lcdc.
So we need some DRM specialist to take a look on it.
BR and thanks, Nikolaus
From: Paul Boddie paul@boddie.org.uk
We need to hook up * HDMI power regulator * HDMI connector * DDC pinmux * HDMI and LCD endpoint connections
Signed-off-by: Paul Boddie paul@boddie.org.uk Signed-off-by: H. Nikolaus Schaller hns@goldelico.com --- arch/mips/boot/dts/ingenic/ci20.dts | 64 +++++++++++++++++++++++++++++ 1 file changed, 64 insertions(+)
diff --git a/arch/mips/boot/dts/ingenic/ci20.dts b/arch/mips/boot/dts/ingenic/ci20.dts index 37b93166bf22..efa8270afbba 100644 --- a/arch/mips/boot/dts/ingenic/ci20.dts +++ b/arch/mips/boot/dts/ingenic/ci20.dts @@ -60,6 +60,28 @@ enable-active-high; };
+ hdmi_power: fixedregulator@2 { + compatible = "regulator-fixed"; + regulator-name = "hdmi_power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpa 25 GPIO_ACTIVE_LOW>; + enable-active-high; + regulator-always-on; + }; + + hdmi_out: connector { + compatible = "hdmi-connector"; + label = "HDMI OUT"; + type = "a"; + + port { + hdmi_con: endpoint { + remote-endpoint = <&dw_hdmi_out>; + }; + }; + }; + wlan0_power: fixedregulator@1 { compatible = "regulator-fixed"; regulator-name = "wlan0_power"; @@ -423,6 +445,12 @@ bias-disable; };
+ pins_hdmi_ddc: hdmi_ddc { + function = "hdmi-ddc"; + groups = "hdmi-ddc"; + bias-disable; + }; + pins_nemc: nemc { function = "nemc"; groups = "nemc-data", "nemc-cle-ale", "nemc-rd-we", "nemc-frd-fwe"; @@ -459,3 +487,39 @@ assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER1>; assigned-clock-rates = <3000000>, <3000000>; }; + +&hdmi { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&pins_hdmi_ddc>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + dw_hdmi_in: endpoint { + remote-endpoint = <&lcd_out>; + }; + }; + + port@1 { + reg = <1>; + dw_hdmi_out: endpoint { + remote-endpoint = <&hdmi_con>; + }; + }; + }; +}; + +&lcd { + status = "okay"; + + port { + lcd_out: endpoint { + remote-endpoint = <&dw_hdmi_in>; + }; + }; +};
We configure them as loadable modules by default.
Signed-off-by: H. Nikolaus Schaller hns@goldelico.com --- arch/mips/configs/ci20_defconfig | 3 +++ 1 file changed, 3 insertions(+)
diff --git a/arch/mips/configs/ci20_defconfig b/arch/mips/configs/ci20_defconfig index be41df2a81fb..3f733a555cb2 100644 --- a/arch/mips/configs/ci20_defconfig +++ b/arch/mips/configs/ci20_defconfig @@ -103,6 +103,9 @@ CONFIG_RTC_CLASS=y CONFIG_RTC_DRV_JZ4740=y CONFIG_DMADEVICES=y CONFIG_DMA_JZ4780=y +CONFIG_DRM=m +CONFIG_DRM_DW_HDMI_JZ4780=m +CONFIG_DRM_DW_HDMI=m # CONFIG_IOMMU_SUPPORT is not set CONFIG_MEMORY=y CONFIG_EXT4_FS=y
dri-devel@lists.freedesktop.org
-
H. Nikolaus Schaller -
Linus Walleij -
Paul Cercueil -
Rob Herring -
Sam Ravnborg