On Tue, Jul 28, 2015 at 1:50 PM, Andreas Färber afaerber@suse.de wrote:

Am 28.07.2015 um 14:54 schrieb Srinivas Kandagatla:

...

This patch adds LVDS panel for IFC6410.

Signed-off-by: Rob Clark robdclark@gmail.com [Rob Clark: WIP patch] Signed-off-by: Srinivas Kandagatla srinivas.kandagatla@linaro.org

---

arch/arm/boot/dts/qcom-apq8064-ifc6410.dts | 66 ++++++++++++++++++++++++++++++ 1 file changed, 66 insertions(+)

diff --git a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts index 1ab71f1..3bdac02 100644 --- a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts +++ b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts @@ -63,6 +63,12 @@ qcom,switch-mode-frequency = <3200000>; };

•                         pm8921_l2: l2 {
  

•                                 regulator-min-microvolt = <1200000>;
  

•                                 regulator-max-microvolt = <1200000>;
  

•                                 bias-pull-down;
  

•                         };
  

•                         pm8921_l3: l3 {
                                  regulator-min-microvolt = <3050000>;
                                  regulator-max-microvolt = <3300000>;
  

@@ -96,6 +102,10 @@ pm8921_lvs1: lvs1 { bias-pull-down; };

•                         pm8921_lvs7: lvs7 {
  

•                                 bias-pull-down;
  

•                         };
                  };
          };
  
  

@@ -119,6 +129,41 @@

          mdp: qcom,mdp@5100000 {
                  status = "okay";

•                 qcom,lvds-panel = <&panel>;
  

In my testing this broke/uglified HDMI output. Since not everyone has that LVDS panel attached, or might have a different panel type, I don't think the panel node belongs in the generic -ifc6410.dts file. I suggest you add an -ifc6410+inforce-lvds.dts or so for that.

I think the problem is not so much the dt bindings, since we have an i2c/ddc where we can probe the panel's edid and see if it is actually attached.

Probably panel_simple_probe() should attempt to read edid (or at least first block) if ddc is not null, and return an error if that times out. That way we could tell at runtime whether the panel is there or not.

BR, -R

...

•                 lvds-vccs-3p3v-supply = <&ext_3p3v>;
  

•                 lvds-pll-vdda-supply = <&pm8921_l2>;
  

•                 lvds-vdda-supply = <&pm8921_lvs7>;
  

•         };
  

•         panel_3p3v: panel_3p3v {
  

s/_/-/ ?

...

•                 compatible = "regulator-fixed";
  

•                 pinctrl-0 = <&disp_en_gpios>;
  

•                 pinctrl-names = "default";
  

•                 regulator-min-microvolt = <3300000>;
  

•                 regulator-max-microvolt = <3300000>;
  

•                 regulator-name = "panel_en_3p3v";
  

•                 regulator-type = "voltage";
  

•                 startup-delay-us = <0>;
  

•                 gpio = <&pm8921_gpio 36 GPIO_ACTIVE_HIGH>;
  

•                 enable-active-high;
  

•                 regulator-boot-on;
  

•         };
  

•         backlight: backlight{
  

•                 pinctrl-0 = <&pwm_bl_gpios>;
  

•                 pinctrl-names = "default";
  

•                 compatible = "gpio-backlight";
  

•                 gpios = <&pm8921_gpio 26 GPIO_ACTIVE_HIGH>;
  

•                 default-on;
  

•         };
  

•         panel: auo,b101xtn01 {
  

panel: panel { ?

Regards, Andreas

...

•                 status = "okay";
  

•                 compatible = "auo,b101xtn01";
  

•                 ddc-i2c-bus = <&i2c3>;
  

•                 backlight = <&backlight>;
  

•                 power-supply = <&panel_3p3v>;
          };
  
          gsbi3: gsbi@16200000 {
  

@@ -235,6 +280,27 @@ pm8921_gpio: gpio@150 { pinctrl-names = "default"; pinctrl-0 = <&wlan_default_gpios>;

•                                 pwm_bl_gpios: pwm-bl-gpios {
  

•                                         pios {
  

•                                                 pins = "gpio26";
  

•                                                 bias-disable;
  

•                                                 function = "normal";
  

•                                                 qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>;
  

•                                                 power-source = <PM8921_GPIO_S4>;
  

•                                         };
  

•                                 };
  

•                                 disp_en_gpios: disp-en-gpios {
  

•                                         pios {
  

•                                                 pins = "gpio36";
  

•                                                 bias-disable;
  

•                                                 function = "normal";
  

•                                                 qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>;
  

•                                                 power-source = <PM8921_GPIO_S4>;
  

•                                         };
  

•                                 };
  

•                                 wlan_default_gpios: wlan-gpios {
                                          pios {
                                                  pins = "gpio43";
  
  

-- SUSE Linux GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany GF: Felix Imendörffer, Jane Smithard, Dilip Upmanyu, Graham Norton; HRB 21284 (AG Nürnberg)