From: Yakir Yang ykk@rock-chips.com
When transmitting IEC60985 linear PCM audio, we configure the Audio Sample Channel Status information of all the channel status bits in the IEC60958 frame. Refer to 60958-3 page 10 for frequency, original frequency, and wordlength setting.
This fix the issue that audio does not come out on some monitors (e.g. LG 22CV241)
Signed-off-by: Yakir Yang ykk@rock-chips.com Signed-off-by: Cheng-Yi Chiang cychiang@chromium.org --- drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 59 +++++++++++++++++++++++ drivers/gpu/drm/bridge/synopsys/dw-hdmi.h | 20 ++++++++ 2 files changed, 79 insertions(+)
diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c index bd65d0479683..34d46e25d610 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c @@ -582,6 +582,63 @@ static unsigned int hdmi_compute_n(unsigned int freq, unsigned long pixel_clk) return n; }
+static void hdmi_set_schnl(struct dw_hdmi *hdmi) +{ + u8 aud_schnl_samplerate; + u8 aud_schnl_8; + + /* These registers are on RK3288 using version 2.0a. */ + if (hdmi->version != 0x200a) + return; + + switch (hdmi->sample_rate) { + case 32000: + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_32K; + break; + case 44100: + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_44K1; + break; + case 48000: + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_48K; + break; + case 88200: + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_88K2; + break; + case 96000: + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_96K; + break; + case 176400: + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_176K4; + break; + case 192000: + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_192K; + break; + case 768000: + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_768K; + break; + default: + dev_warn(hdmi->dev, "Unsupported audio sample rate (%u)\n", + hdmi->sample_rate); + return; + } + + /* set channel status register */ + hdmi_modb(hdmi, aud_schnl_samplerate, HDMI_FC_AUDSCHNLS7_SMPRATE_MASK, + HDMI_FC_AUDSCHNLS7); + + /* + * Set original frequency to be the same as frequency. + * Use one-complement value as stated in IEC60958-3 page 13. + */ + aud_schnl_8 = (~aud_schnl_samplerate) << + HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_OFFSET; + + /* This means word length is 16 bit. Refer to IEC60958-3 page 12. */ + aud_schnl_8 |= 2 << HDMI_FC_AUDSCHNLS8_WORDLEGNTH_OFFSET; + + hdmi_writeb(hdmi, aud_schnl_8, HDMI_FC_AUDSCHNLS8); +} + static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi, unsigned long pixel_clk, unsigned int sample_rate) { @@ -620,6 +677,8 @@ static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi, hdmi->audio_cts = cts; hdmi_set_cts_n(hdmi, cts, hdmi->audio_enable ? n : 0); spin_unlock_irq(&hdmi->audio_lock); + + hdmi_set_schnl(hdmi); }
static void hdmi_init_clk_regenerator(struct dw_hdmi *hdmi) diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h index 6988f12d89d9..619ebc1c8354 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h @@ -158,6 +158,17 @@ #define HDMI_FC_SPDDEVICEINF 0x1062 #define HDMI_FC_AUDSCONF 0x1063 #define HDMI_FC_AUDSSTAT 0x1064 +#define HDMI_FC_AUDSV 0x1065 +#define HDMI_FC_AUDSU 0x1066 +#define HDMI_FC_AUDSCHNLS0 0x1067 +#define HDMI_FC_AUDSCHNLS1 0x1068 +#define HDMI_FC_AUDSCHNLS2 0x1069 +#define HDMI_FC_AUDSCHNLS3 0x106a +#define HDMI_FC_AUDSCHNLS4 0x106b +#define HDMI_FC_AUDSCHNLS5 0x106c +#define HDMI_FC_AUDSCHNLS6 0x106d +#define HDMI_FC_AUDSCHNLS7 0x106e +#define HDMI_FC_AUDSCHNLS8 0x106f #define HDMI_FC_DATACH0FILL 0x1070 #define HDMI_FC_DATACH1FILL 0x1071 #define HDMI_FC_DATACH2FILL 0x1072 @@ -706,6 +717,15 @@ enum { /* HDMI_FC_AUDSCHNLS7 field values */ HDMI_FC_AUDSCHNLS7_ACCURACY_OFFSET = 4, HDMI_FC_AUDSCHNLS7_ACCURACY_MASK = 0x30, + HDMI_FC_AUDSCHNLS7_SMPRATE_MASK = 0x0f, + HDMI_FC_AUDSCHNLS7_SMPRATE_192K = 0xe, + HDMI_FC_AUDSCHNLS7_SMPRATE_176K4 = 0xc, + HDMI_FC_AUDSCHNLS7_SMPRATE_96K = 0xa, + HDMI_FC_AUDSCHNLS7_SMPRATE_768K = 0x9, + HDMI_FC_AUDSCHNLS7_SMPRATE_88K2 = 0x8, + HDMI_FC_AUDSCHNLS7_SMPRATE_32K = 0x3, + HDMI_FC_AUDSCHNLS7_SMPRATE_48K = 0x2, + HDMI_FC_AUDSCHNLS7_SMPRATE_44K1 = 0x0,
/* HDMI_FC_AUDSCHNLS8 field values */ HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_MASK = 0xf0,
Hi,
On 03/09/2019 07:51, Cheng-Yi Chiang wrote:
From: Yakir Yang ykk@rock-chips.com
When transmitting IEC60985 linear PCM audio, we configure the Audio Sample Channel Status information of all the channel status bits in the IEC60958 frame. Refer to 60958-3 page 10 for frequency, original frequency, and wordlength setting.
This fix the issue that audio does not come out on some monitors (e.g. LG 22CV241)
Signed-off-by: Yakir Yang ykk@rock-chips.com Signed-off-by: Cheng-Yi Chiang cychiang@chromium.org
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 59 +++++++++++++++++++++++ drivers/gpu/drm/bridge/synopsys/dw-hdmi.h | 20 ++++++++ 2 files changed, 79 insertions(+)
diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c index bd65d0479683..34d46e25d610 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c @@ -582,6 +582,63 @@ static unsigned int hdmi_compute_n(unsigned int freq, unsigned long pixel_clk) return n; }
+static void hdmi_set_schnl(struct dw_hdmi *hdmi) +{
- u8 aud_schnl_samplerate;
- u8 aud_schnl_8;
- /* These registers are on RK3288 using version 2.0a. */
- if (hdmi->version != 0x200a)
return;
Are these limited to the 2.0a version *in* RK3288, or 2.0a version on all SoCs ?
- switch (hdmi->sample_rate) {
- case 32000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_32K;break;- case 44100:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_44K1;break;- case 48000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_48K;break;- case 88200:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_88K2;break;- case 96000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_96K;break;- case 176400:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_176K4;break;- case 192000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_192K;break;- case 768000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_768K;break;- default:
dev_warn(hdmi->dev, "Unsupported audio sample rate (%u)\n",hdmi->sample_rate);return;- }
- /* set channel status register */
- hdmi_modb(hdmi, aud_schnl_samplerate, HDMI_FC_AUDSCHNLS7_SMPRATE_MASK,
HDMI_FC_AUDSCHNLS7);- /*
* Set original frequency to be the same as frequency.* Use one-complement value as stated in IEC60958-3 page 13.*/- aud_schnl_8 = (~aud_schnl_samplerate) <<
HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_OFFSET;- /* This means word length is 16 bit. Refer to IEC60958-3 page 12. */
- aud_schnl_8 |= 2 << HDMI_FC_AUDSCHNLS8_WORDLEGNTH_OFFSET;
- hdmi_writeb(hdmi, aud_schnl_8, HDMI_FC_AUDSCHNLS8);
+}
static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi, unsigned long pixel_clk, unsigned int sample_rate) { @@ -620,6 +677,8 @@ static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi, hdmi->audio_cts = cts; hdmi_set_cts_n(hdmi, cts, hdmi->audio_enable ? n : 0); spin_unlock_irq(&hdmi->audio_lock);
- hdmi_set_schnl(hdmi);
}
static void hdmi_init_clk_regenerator(struct dw_hdmi *hdmi) diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h index 6988f12d89d9..619ebc1c8354 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h @@ -158,6 +158,17 @@ #define HDMI_FC_SPDDEVICEINF 0x1062 #define HDMI_FC_AUDSCONF 0x1063 #define HDMI_FC_AUDSSTAT 0x1064 +#define HDMI_FC_AUDSV 0x1065 +#define HDMI_FC_AUDSU 0x1066 +#define HDMI_FC_AUDSCHNLS0 0x1067 +#define HDMI_FC_AUDSCHNLS1 0x1068 +#define HDMI_FC_AUDSCHNLS2 0x1069 +#define HDMI_FC_AUDSCHNLS3 0x106a +#define HDMI_FC_AUDSCHNLS4 0x106b +#define HDMI_FC_AUDSCHNLS5 0x106c +#define HDMI_FC_AUDSCHNLS6 0x106d +#define HDMI_FC_AUDSCHNLS7 0x106e +#define HDMI_FC_AUDSCHNLS8 0x106f #define HDMI_FC_DATACH0FILL 0x1070 #define HDMI_FC_DATACH1FILL 0x1071 #define HDMI_FC_DATACH2FILL 0x1072 @@ -706,6 +717,15 @@ enum { /* HDMI_FC_AUDSCHNLS7 field values */ HDMI_FC_AUDSCHNLS7_ACCURACY_OFFSET = 4, HDMI_FC_AUDSCHNLS7_ACCURACY_MASK = 0x30,
- HDMI_FC_AUDSCHNLS7_SMPRATE_MASK = 0x0f,
- HDMI_FC_AUDSCHNLS7_SMPRATE_192K = 0xe,
- HDMI_FC_AUDSCHNLS7_SMPRATE_176K4 = 0xc,
- HDMI_FC_AUDSCHNLS7_SMPRATE_96K = 0xa,
- HDMI_FC_AUDSCHNLS7_SMPRATE_768K = 0x9,
- HDMI_FC_AUDSCHNLS7_SMPRATE_88K2 = 0x8,
- HDMI_FC_AUDSCHNLS7_SMPRATE_32K = 0x3,
- HDMI_FC_AUDSCHNLS7_SMPRATE_48K = 0x2,
- HDMI_FC_AUDSCHNLS7_SMPRATE_44K1 = 0x0,
/* HDMI_FC_AUDSCHNLS8 field values */ HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_MASK = 0xf0,
Hi,
Le 03/09/2019 à 11:53, Neil Armstrong a écrit :
Hi,
On 03/09/2019 07:51, Cheng-Yi Chiang wrote:
From: Yakir Yang ykk@rock-chips.com
When transmitting IEC60985 linear PCM audio, we configure the Audio Sample Channel Status information of all the channel status bits in the IEC60958 frame. Refer to 60958-3 page 10 for frequency, original frequency, and wordlength setting.
This fix the issue that audio does not come out on some monitors (e.g. LG 22CV241)
Signed-off-by: Yakir Yang ykk@rock-chips.com Signed-off-by: Cheng-Yi Chiang cychiang@chromium.org
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 59 +++++++++++++++++++++++ drivers/gpu/drm/bridge/synopsys/dw-hdmi.h | 20 ++++++++ 2 files changed, 79 insertions(+)
diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c index bd65d0479683..34d46e25d610 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c @@ -582,6 +582,63 @@ static unsigned int hdmi_compute_n(unsigned int freq, unsigned long pixel_clk) return n; }
+static void hdmi_set_schnl(struct dw_hdmi *hdmi) +{
- u8 aud_schnl_samplerate;
- u8 aud_schnl_8;
- /* These registers are on RK3288 using version 2.0a. */
- if (hdmi->version != 0x200a)
return;Are these limited to the 2.0a version *in* RK3288, or 2.0a version on all SoCs ?
After investigations, Amlogic sets these registers on their 2.0a version aswell, and Jernej (added in Cc) reported me Allwinner sets them on their < 2.0a and > 2.0a IPs versions.
Can you check on the Rockchip IP versions in RK3399 ?
For reference, the HDMI 1.4a IP version allwinner setups is: https://github.com/Allwinner-Homlet/H3-BSP4.4-linux/blob/master/drivers/vide... (registers a "scrambled" but a custom bit can reset to the original mapping, 0x1066 ... 0x106f)
Neil
- switch (hdmi->sample_rate) {
- case 32000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_32K;break;- case 44100:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_44K1;break;- case 48000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_48K;break;- case 88200:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_88K2;break;- case 96000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_96K;break;- case 176400:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_176K4;break;- case 192000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_192K;break;- case 768000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_768K;break;- default:
dev_warn(hdmi->dev, "Unsupported audio sample rate (%u)\n",hdmi->sample_rate);return;- }
- /* set channel status register */
- hdmi_modb(hdmi, aud_schnl_samplerate, HDMI_FC_AUDSCHNLS7_SMPRATE_MASK,
HDMI_FC_AUDSCHNLS7);- /*
* Set original frequency to be the same as frequency.* Use one-complement value as stated in IEC60958-3 page 13.*/- aud_schnl_8 = (~aud_schnl_samplerate) <<
HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_OFFSET;- /* This means word length is 16 bit. Refer to IEC60958-3 page 12. */
- aud_schnl_8 |= 2 << HDMI_FC_AUDSCHNLS8_WORDLEGNTH_OFFSET;
- hdmi_writeb(hdmi, aud_schnl_8, HDMI_FC_AUDSCHNLS8);
+}
static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi, unsigned long pixel_clk, unsigned int sample_rate) { @@ -620,6 +677,8 @@ static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi, hdmi->audio_cts = cts; hdmi_set_cts_n(hdmi, cts, hdmi->audio_enable ? n : 0); spin_unlock_irq(&hdmi->audio_lock);
- hdmi_set_schnl(hdmi);
}
static void hdmi_init_clk_regenerator(struct dw_hdmi *hdmi) diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h index 6988f12d89d9..619ebc1c8354 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h @@ -158,6 +158,17 @@ #define HDMI_FC_SPDDEVICEINF 0x1062 #define HDMI_FC_AUDSCONF 0x1063 #define HDMI_FC_AUDSSTAT 0x1064 +#define HDMI_FC_AUDSV 0x1065 +#define HDMI_FC_AUDSU 0x1066 +#define HDMI_FC_AUDSCHNLS0 0x1067 +#define HDMI_FC_AUDSCHNLS1 0x1068 +#define HDMI_FC_AUDSCHNLS2 0x1069 +#define HDMI_FC_AUDSCHNLS3 0x106a +#define HDMI_FC_AUDSCHNLS4 0x106b +#define HDMI_FC_AUDSCHNLS5 0x106c +#define HDMI_FC_AUDSCHNLS6 0x106d +#define HDMI_FC_AUDSCHNLS7 0x106e +#define HDMI_FC_AUDSCHNLS8 0x106f #define HDMI_FC_DATACH0FILL 0x1070 #define HDMI_FC_DATACH1FILL 0x1071 #define HDMI_FC_DATACH2FILL 0x1072 @@ -706,6 +717,15 @@ enum { /* HDMI_FC_AUDSCHNLS7 field values */ HDMI_FC_AUDSCHNLS7_ACCURACY_OFFSET = 4, HDMI_FC_AUDSCHNLS7_ACCURACY_MASK = 0x30,
- HDMI_FC_AUDSCHNLS7_SMPRATE_MASK = 0x0f,
- HDMI_FC_AUDSCHNLS7_SMPRATE_192K = 0xe,
- HDMI_FC_AUDSCHNLS7_SMPRATE_176K4 = 0xc,
- HDMI_FC_AUDSCHNLS7_SMPRATE_96K = 0xa,
- HDMI_FC_AUDSCHNLS7_SMPRATE_768K = 0x9,
- HDMI_FC_AUDSCHNLS7_SMPRATE_88K2 = 0x8,
- HDMI_FC_AUDSCHNLS7_SMPRATE_32K = 0x3,
- HDMI_FC_AUDSCHNLS7_SMPRATE_48K = 0x2,
- HDMI_FC_AUDSCHNLS7_SMPRATE_44K1 = 0x0,
/* HDMI_FC_AUDSCHNLS8 field values */ HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_MASK = 0xf0,
Hi!
Dne torek, 03. september 2019 ob 20:00:33 CEST je Neil Armstrong napisal(a):
Hi,
Le 03/09/2019 à 11:53, Neil Armstrong a écrit :
Hi,
On 03/09/2019 07:51, Cheng-Yi Chiang wrote:
From: Yakir Yang ykk@rock-chips.com
When transmitting IEC60985 linear PCM audio, we configure the Audio Sample Channel Status information of all the channel status bits in the IEC60958 frame. Refer to 60958-3 page 10 for frequency, original frequency, and wordlength setting.
This fix the issue that audio does not come out on some monitors (e.g. LG 22CV241)
Signed-off-by: Yakir Yang ykk@rock-chips.com Signed-off-by: Cheng-Yi Chiang cychiang@chromium.org
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 59 +++++++++++++++++++++++ drivers/gpu/drm/bridge/synopsys/dw-hdmi.h | 20 ++++++++ 2 files changed, 79 insertions(+)
diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c index bd65d0479683..34d46e25d610 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c @@ -582,6 +582,63 @@ static unsigned int hdmi_compute_n(unsigned int freq, unsigned long pixel_clk)>> return n;
}
+static void hdmi_set_schnl(struct dw_hdmi *hdmi) +{
- u8 aud_schnl_samplerate;
- u8 aud_schnl_8;
- /* These registers are on RK3288 using version 2.0a. */
- if (hdmi->version != 0x200a)
return;Are these limited to the 2.0a version *in* RK3288, or 2.0a version on all SoCs ?
After investigations, Amlogic sets these registers on their 2.0a version aswell, and Jernej (added in Cc) reported me Allwinner sets them on their < 2.0a and > 2.0a IPs versions.
Can you check on the Rockchip IP versions in RK3399 ?
For reference, the HDMI 1.4a IP version allwinner setups is: https://github.com/Allwinner-Homlet/H3-BSP4.4-linux/blob/master/drivers/vide o/fbdev/sunxi/disp2/hdmi/hdmi_bsp_sun8iw7.c#L531-L539 (registers a "scrambled" but a custom bit can reset to the original mapping, 0x1066 ... 0x106f)
For easier reading, here is similar, but annotated version: http://ix.io/1Ub6 Check function bsp_hdmi_audio().
Unless there is a special reason, you can just remove that check.
Best regards, Jernej
Neil
- switch (hdmi->sample_rate) {
- case 32000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_32K;break;- case 44100:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_44K1;break;- case 48000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_48K;break;- case 88200:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_88K2;break;- case 96000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_96K;break;- case 176400:
aud_schnl_samplerate =
HDMI_FC_AUDSCHNLS7_SMPRATE_176K4;
break;- case 192000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_192K;break;- case 768000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_768K;break;- default:
dev_warn(hdmi->dev, "Unsupported audio sample rate (%u)
\n",
hdmi->sample_rate);return;- }
- /* set channel status register */
- hdmi_modb(hdmi, aud_schnl_samplerate,
HDMI_FC_AUDSCHNLS7_SMPRATE_MASK,
HDMI_FC_AUDSCHNLS7);- /*
* Set original frequency to be the same as frequency.* Use one-complement value as stated in IEC60958-3 page 13.*/- aud_schnl_8 = (~aud_schnl_samplerate) <<
HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_OFFSET;- /* This means word length is 16 bit. Refer to IEC60958-3 page 12.
*/
- aud_schnl_8 |= 2 << HDMI_FC_AUDSCHNLS8_WORDLEGNTH_OFFSET;
- hdmi_writeb(hdmi, aud_schnl_8, HDMI_FC_AUDSCHNLS8);
+}
static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi,
unsigned long pixel_clk, unsigned int sample_rate)
{
@@ -620,6 +677,8 @@ static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi,>> hdmi->audio_cts = cts; hdmi_set_cts_n(hdmi, cts, hdmi->audio_enable ? n : 0); spin_unlock_irq(&hdmi->audio_lock);
- hdmi_set_schnl(hdmi);
}
static void hdmi_init_clk_regenerator(struct dw_hdmi *hdmi)
diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h index 6988f12d89d9..619ebc1c8354 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h @@ -158,6 +158,17 @@
#define HDMI_FC_SPDDEVICEINF 0x1062 #define HDMI_FC_AUDSCONF 0x1063 #define HDMI_FC_AUDSSTAT 0x1064
+#define HDMI_FC_AUDSV 0x1065 +#define HDMI_FC_AUDSU 0x1066 +#define HDMI_FC_AUDSCHNLS0 0x1067 +#define HDMI_FC_AUDSCHNLS1 0x1068 +#define HDMI_FC_AUDSCHNLS2 0x1069 +#define HDMI_FC_AUDSCHNLS3 0x106a +#define HDMI_FC_AUDSCHNLS4 0x106b +#define HDMI_FC_AUDSCHNLS5 0x106c +#define HDMI_FC_AUDSCHNLS6 0x106d +#define HDMI_FC_AUDSCHNLS7 0x106e +#define HDMI_FC_AUDSCHNLS8 0x106f
#define HDMI_FC_DATACH0FILL 0x1070 #define HDMI_FC_DATACH1FILL 0x1071 #define HDMI_FC_DATACH2FILL 0x1072
@@ -706,6 +717,15 @@ enum {
/* HDMI_FC_AUDSCHNLS7 field values */
HDMI_FC_AUDSCHNLS7_ACCURACY_OFFSET = 4, HDMI_FC_AUDSCHNLS7_ACCURACY_MASK = 0x30,
- HDMI_FC_AUDSCHNLS7_SMPRATE_MASK = 0x0f,
- HDMI_FC_AUDSCHNLS7_SMPRATE_192K = 0xe,
- HDMI_FC_AUDSCHNLS7_SMPRATE_176K4 = 0xc,
- HDMI_FC_AUDSCHNLS7_SMPRATE_96K = 0xa,
- HDMI_FC_AUDSCHNLS7_SMPRATE_768K = 0x9,
- HDMI_FC_AUDSCHNLS7_SMPRATE_88K2 = 0x8,
- HDMI_FC_AUDSCHNLS7_SMPRATE_32K = 0x3,
- HDMI_FC_AUDSCHNLS7_SMPRATE_48K = 0x2,
- HDMI_FC_AUDSCHNLS7_SMPRATE_44K1 = 0x0,
/* HDMI_FC_AUDSCHNLS8 field values */
HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_MASK = 0xf0,
On 2019-09-03 20:08, Jernej Škrabec wrote:
Hi!
Dne torek, 03. september 2019 ob 20:00:33 CEST je Neil Armstrong napisal(a):
Hi,
Le 03/09/2019 à 11:53, Neil Armstrong a écrit :
Hi,
On 03/09/2019 07:51, Cheng-Yi Chiang wrote:
From: Yakir Yang ykk@rock-chips.com
When transmitting IEC60985 linear PCM audio, we configure the Audio Sample Channel Status information of all the channel status bits in the IEC60958 frame. Refer to 60958-3 page 10 for frequency, original frequency, and wordlength setting.
This fix the issue that audio does not come out on some monitors (e.g. LG 22CV241)
Signed-off-by: Yakir Yang ykk@rock-chips.com Signed-off-by: Cheng-Yi Chiang cychiang@chromium.org
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 59 +++++++++++++++++++++++ drivers/gpu/drm/bridge/synopsys/dw-hdmi.h | 20 ++++++++ 2 files changed, 79 insertions(+)
diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c index bd65d0479683..34d46e25d610 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c @@ -582,6 +582,63 @@ static unsigned int hdmi_compute_n(unsigned int freq, unsigned long pixel_clk)>> return n;
}
+static void hdmi_set_schnl(struct dw_hdmi *hdmi) +{
- u8 aud_schnl_samplerate;
- u8 aud_schnl_8;
- /* These registers are on RK3288 using version 2.0a. */
- if (hdmi->version != 0x200a)
return;Are these limited to the 2.0a version *in* RK3288, or 2.0a version on all SoCs ?
After investigations, Amlogic sets these registers on their 2.0a version aswell, and Jernej (added in Cc) reported me Allwinner sets them on their < 2.0a and > 2.0a IPs versions.
Can you check on the Rockchip IP versions in RK3399 ?
For reference, the HDMI 1.4a IP version allwinner setups is: https://github.com/Allwinner-Homlet/H3-BSP4.4-linux/blob/master/drivers/vide o/fbdev/sunxi/disp2/hdmi/hdmi_bsp_sun8iw7.c#L531-L539 (registers a "scrambled" but a custom bit can reset to the original mapping, 0x1066 ... 0x106f)
For easier reading, here is similar, but annotated version: http://ix.io/1Ub6 Check function bsp_hdmi_audio().
Unless there is a special reason, you can just remove that check.
Agree, this check should not be needed, AUDSCHNLS7 used to be configured in my old multi-channel patches that have seen lot of testing on Amlogic, Allwinner and Rockchip SoCs.
Best regards, Jernej
Neil
- switch (hdmi->sample_rate) {
- case 32000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_32K;break;- case 44100:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_44K1;break;- case 48000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_48K;break;- case 88200:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_88K2;break;- case 96000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_96K;break;- case 176400:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_176K4;break;- case 192000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_192K;break;- case 768000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_768K;break;- default:
dev_warn(hdmi->dev, "Unsupported audio sample rate (%u)\n",hdmi->sample_rate);return;- }
- /* set channel status register */
- hdmi_modb(hdmi, aud_schnl_samplerate, HDMI_FC_AUDSCHNLS7_SMPRATE_MASK,
HDMI_FC_AUDSCHNLS7);- /*
* Set original frequency to be the same as frequency.* Use one-complement value as stated in IEC60958-3 page 13.*/- aud_schnl_8 = (~aud_schnl_samplerate) <<
HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_OFFSET;- /* This means word length is 16 bit. Refer to IEC60958-3 page 12. */
- aud_schnl_8 |= 2 << HDMI_FC_AUDSCHNLS8_WORDLEGNTH_OFFSET;
This looks wrong, user can use 16 and 24 bit wide audio streams.
- hdmi_writeb(hdmi, aud_schnl_8, HDMI_FC_AUDSCHNLS8);
+}
static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi,
unsigned long pixel_clk, unsigned int sample_rate)
{
@@ -620,6 +677,8 @@ static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi,>> hdmi->audio_cts = cts; hdmi_set_cts_n(hdmi, cts, hdmi->audio_enable ? n : 0); spin_unlock_irq(&hdmi->audio_lock);
- hdmi_set_schnl(hdmi);
I will suggest this function is called from or merged with dw_hdmi_set_sample_rate(). Similar to how AUDSCONF and AUDICONF0 is configured from dw_hdmi_set_channel_count().
Regards, Jonas
}
static void hdmi_init_clk_regenerator(struct dw_hdmi *hdmi)
diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h index 6988f12d89d9..619ebc1c8354 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h @@ -158,6 +158,17 @@
#define HDMI_FC_SPDDEVICEINF 0x1062 #define HDMI_FC_AUDSCONF 0x1063 #define HDMI_FC_AUDSSTAT 0x1064
+#define HDMI_FC_AUDSV 0x1065 +#define HDMI_FC_AUDSU 0x1066 +#define HDMI_FC_AUDSCHNLS0 0x1067 +#define HDMI_FC_AUDSCHNLS1 0x1068 +#define HDMI_FC_AUDSCHNLS2 0x1069 +#define HDMI_FC_AUDSCHNLS3 0x106a +#define HDMI_FC_AUDSCHNLS4 0x106b +#define HDMI_FC_AUDSCHNLS5 0x106c +#define HDMI_FC_AUDSCHNLS6 0x106d +#define HDMI_FC_AUDSCHNLS7 0x106e +#define HDMI_FC_AUDSCHNLS8 0x106f
#define HDMI_FC_DATACH0FILL 0x1070 #define HDMI_FC_DATACH1FILL 0x1071 #define HDMI_FC_DATACH2FILL 0x1072
@@ -706,6 +717,15 @@ enum {
/* HDMI_FC_AUDSCHNLS7 field values */
HDMI_FC_AUDSCHNLS7_ACCURACY_OFFSET = 4, HDMI_FC_AUDSCHNLS7_ACCURACY_MASK = 0x30,
- HDMI_FC_AUDSCHNLS7_SMPRATE_MASK = 0x0f,
- HDMI_FC_AUDSCHNLS7_SMPRATE_192K = 0xe,
- HDMI_FC_AUDSCHNLS7_SMPRATE_176K4 = 0xc,
- HDMI_FC_AUDSCHNLS7_SMPRATE_96K = 0xa,
- HDMI_FC_AUDSCHNLS7_SMPRATE_768K = 0x9,
- HDMI_FC_AUDSCHNLS7_SMPRATE_88K2 = 0x8,
- HDMI_FC_AUDSCHNLS7_SMPRATE_32K = 0x3,
- HDMI_FC_AUDSCHNLS7_SMPRATE_48K = 0x2,
- HDMI_FC_AUDSCHNLS7_SMPRATE_44K1 = 0x0,
/* HDMI_FC_AUDSCHNLS8 field values */
HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_MASK = 0xf0,
On Wed, Sep 4, 2019 at 4:33 AM Jonas Karlman jonas@kwiboo.se wrote:
On 2019-09-03 20:08, Jernej Škrabec wrote:
Hi!
Dne torek, 03. september 2019 ob 20:00:33 CEST je Neil Armstrong napisal(a):
Hi,
Le 03/09/2019 à 11:53, Neil Armstrong a écrit :
Hi,
On 03/09/2019 07:51, Cheng-Yi Chiang wrote:
From: Yakir Yang ykk@rock-chips.com
When transmitting IEC60985 linear PCM audio, we configure the Audio Sample Channel Status information of all the channel status bits in the IEC60958 frame. Refer to 60958-3 page 10 for frequency, original frequency, and wordlength setting.
This fix the issue that audio does not come out on some monitors (e.g. LG 22CV241)
Signed-off-by: Yakir Yang ykk@rock-chips.com Signed-off-by: Cheng-Yi Chiang cychiang@chromium.org
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 59 +++++++++++++++++++++++ drivers/gpu/drm/bridge/synopsys/dw-hdmi.h | 20 ++++++++ 2 files changed, 79 insertions(+)
diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c index bd65d0479683..34d46e25d610 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c @@ -582,6 +582,63 @@ static unsigned int hdmi_compute_n(unsigned int freq, unsigned long pixel_clk)>> return n;
}
+static void hdmi_set_schnl(struct dw_hdmi *hdmi) +{
- u8 aud_schnl_samplerate;
- u8 aud_schnl_8;
- /* These registers are on RK3288 using version 2.0a. */
- if (hdmi->version != 0x200a)
return;Are these limited to the 2.0a version *in* RK3288, or 2.0a version on all SoCs ?
After investigations, Amlogic sets these registers on their 2.0a version aswell, and Jernej (added in Cc) reported me Allwinner sets them on their < 2.0a and > 2.0a IPs versions.
Can you check on the Rockchip IP versions in RK3399 ?
For reference, the HDMI 1.4a IP version allwinner setups is: https://github.com/Allwinner-Homlet/H3-BSP4.4-linux/blob/master/drivers/vide o/fbdev/sunxi/disp2/hdmi/hdmi_bsp_sun8iw7.c#L531-L539 (registers a "scrambled" but a custom bit can reset to the original mapping, 0x1066 ... 0x106f)
For easier reading, here is similar, but annotated version: http://ix.io/1Ub6 Check function bsp_hdmi_audio().
Unless there is a special reason, you can just remove that check.
Agree, this check should not be needed, AUDSCHNLS7 used to be configured in my old multi-channel patches that have seen lot of testing on Amlogic, Allwinner and Rockchip SoCs.
As stated in previous mail, I will modify the check for version >=1.4 since I know that 1.3 does not have such register, at least on iMX6.
Best regards, Jernej
Neil
- switch (hdmi->sample_rate) {
- case 32000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_32K;break;- case 44100:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_44K1;break;- case 48000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_48K;break;- case 88200:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_88K2;break;- case 96000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_96K;break;- case 176400:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_176K4;break;- case 192000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_192K;break;- case 768000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_768K;break;- default:
dev_warn(hdmi->dev, "Unsupported audio sample rate (%u)\n",hdmi->sample_rate);return;- }
- /* set channel status register */
- hdmi_modb(hdmi, aud_schnl_samplerate, HDMI_FC_AUDSCHNLS7_SMPRATE_MASK,
HDMI_FC_AUDSCHNLS7);- /*
- Set original frequency to be the same as frequency.
- Use one-complement value as stated in IEC60958-3 page 13.
- */
- aud_schnl_8 = (~aud_schnl_samplerate) <<
HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_OFFSET;- /* This means word length is 16 bit. Refer to IEC60958-3 page 12. */
- aud_schnl_8 |= 2 << HDMI_FC_AUDSCHNLS8_WORDLEGNTH_OFFSET;
This looks wrong, user can use 16 and 24 bit wide audio streams.
Thanks for spotting this issue. I will fix it in v2 (following how http://ix.io/1Ub6 set it for 16 and 24 bit)
- hdmi_writeb(hdmi, aud_schnl_8, HDMI_FC_AUDSCHNLS8);
+}
static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi,
unsigned long pixel_clk, unsigned int sample_rate)
{
@@ -620,6 +677,8 @@ static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi,>> hdmi->audio_cts = cts; hdmi_set_cts_n(hdmi, cts, hdmi->audio_enable ? n : 0); spin_unlock_irq(&hdmi->audio_lock);
- hdmi_set_schnl(hdmi);
I will suggest this function is called from or merged with dw_hdmi_set_sample_rate(). Similar to how AUDSCONF and AUDICONF0 is configured from dw_hdmi_set_channel_count().
I see. I think it will make sense to add a function set_channel_status() for dw-hdmi-i2s-audio.c to call, since this function is more than just setting rate. Will fix in v2.
Thanks!
Regards, Jonas
}
static void hdmi_init_clk_regenerator(struct dw_hdmi *hdmi)
diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h index 6988f12d89d9..619ebc1c8354 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h @@ -158,6 +158,17 @@
#define HDMI_FC_SPDDEVICEINF 0x1062 #define HDMI_FC_AUDSCONF 0x1063 #define HDMI_FC_AUDSSTAT 0x1064
+#define HDMI_FC_AUDSV 0x1065 +#define HDMI_FC_AUDSU 0x1066 +#define HDMI_FC_AUDSCHNLS0 0x1067 +#define HDMI_FC_AUDSCHNLS1 0x1068 +#define HDMI_FC_AUDSCHNLS2 0x1069 +#define HDMI_FC_AUDSCHNLS3 0x106a +#define HDMI_FC_AUDSCHNLS4 0x106b +#define HDMI_FC_AUDSCHNLS5 0x106c +#define HDMI_FC_AUDSCHNLS6 0x106d +#define HDMI_FC_AUDSCHNLS7 0x106e +#define HDMI_FC_AUDSCHNLS8 0x106f
#define HDMI_FC_DATACH0FILL 0x1070 #define HDMI_FC_DATACH1FILL 0x1071 #define HDMI_FC_DATACH2FILL 0x1072
@@ -706,6 +717,15 @@ enum {
/* HDMI_FC_AUDSCHNLS7 field values */
HDMI_FC_AUDSCHNLS7_ACCURACY_OFFSET = 4, HDMI_FC_AUDSCHNLS7_ACCURACY_MASK = 0x30,
- HDMI_FC_AUDSCHNLS7_SMPRATE_MASK = 0x0f,
- HDMI_FC_AUDSCHNLS7_SMPRATE_192K = 0xe,
- HDMI_FC_AUDSCHNLS7_SMPRATE_176K4 = 0xc,
- HDMI_FC_AUDSCHNLS7_SMPRATE_96K = 0xa,
- HDMI_FC_AUDSCHNLS7_SMPRATE_768K = 0x9,
- HDMI_FC_AUDSCHNLS7_SMPRATE_88K2 = 0x8,
- HDMI_FC_AUDSCHNLS7_SMPRATE_32K = 0x3,
- HDMI_FC_AUDSCHNLS7_SMPRATE_48K = 0x2,
- HDMI_FC_AUDSCHNLS7_SMPRATE_44K1 = 0x0,
/* HDMI_FC_AUDSCHNLS8 field values */
HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_MASK = 0xf0,
On Wed, Sep 4, 2019 at 2:08 AM Jernej Škrabec jernej.skrabec@siol.net wrote:
Hi!
Dne torek, 03. september 2019 ob 20:00:33 CEST je Neil Armstrong napisal(a):
Hi,
Le 03/09/2019 à 11:53, Neil Armstrong a écrit :
Hi,
On 03/09/2019 07:51, Cheng-Yi Chiang wrote:
From: Yakir Yang ykk@rock-chips.com
When transmitting IEC60985 linear PCM audio, we configure the Audio Sample Channel Status information of all the channel status bits in the IEC60958 frame. Refer to 60958-3 page 10 for frequency, original frequency, and wordlength setting.
This fix the issue that audio does not come out on some monitors (e.g. LG 22CV241)
Signed-off-by: Yakir Yang ykk@rock-chips.com Signed-off-by: Cheng-Yi Chiang cychiang@chromium.org
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 59 +++++++++++++++++++++++ drivers/gpu/drm/bridge/synopsys/dw-hdmi.h | 20 ++++++++ 2 files changed, 79 insertions(+)
diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c index bd65d0479683..34d46e25d610 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c @@ -582,6 +582,63 @@ static unsigned int hdmi_compute_n(unsigned int freq, unsigned long pixel_clk)>> return n;
}
+static void hdmi_set_schnl(struct dw_hdmi *hdmi) +{
- u8 aud_schnl_samplerate;
- u8 aud_schnl_8;
- /* These registers are on RK3288 using version 2.0a. */
- if (hdmi->version != 0x200a)
return;Are these limited to the 2.0a version *in* RK3288, or 2.0a version on all SoCs ?
After investigations, Amlogic sets these registers on their 2.0a version aswell, and Jernej (added in Cc) reported me Allwinner sets them on their < 2.0a and > 2.0a IPs versions.
Can you check on the Rockchip IP versions in RK3399 ?
For reference, the HDMI 1.4a IP version allwinner setups is: https://github.com/Allwinner-Homlet/H3-BSP4.4-linux/blob/master/drivers/vide o/fbdev/sunxi/disp2/hdmi/hdmi_bsp_sun8iw7.c#L531-L539 (registers a "scrambled" but a custom bit can reset to the original mapping, 0x1066 ... 0x106f)
For easier reading, here is similar, but annotated version: http://ix.io/1Ub6 Check function bsp_hdmi_audio().
Unless there is a special reason, you can just remove that check.
Thanks for the great reference. I also see that I need to set the word length according to the desired value passed by dw_hdmi_i2s_hw_params in dw-hdmi-i2s-audio.c. Will fix in v2.
Best regards, Jernej
Neil
- switch (hdmi->sample_rate) {
- case 32000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_32K;break;- case 44100:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_44K1;break;- case 48000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_48K;break;- case 88200:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_88K2;break;- case 96000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_96K;break;- case 176400:
aud_schnl_samplerate =HDMI_FC_AUDSCHNLS7_SMPRATE_176K4;
break;- case 192000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_192K;break;- case 768000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_768K;break;- default:
dev_warn(hdmi->dev, "Unsupported audio sample rate (%u)\n",
hdmi->sample_rate);return;- }
- /* set channel status register */
- hdmi_modb(hdmi, aud_schnl_samplerate,
HDMI_FC_AUDSCHNLS7_SMPRATE_MASK,
HDMI_FC_AUDSCHNLS7);- /*
- Set original frequency to be the same as frequency.
- Use one-complement value as stated in IEC60958-3 page 13.
- */
- aud_schnl_8 = (~aud_schnl_samplerate) <<
HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_OFFSET;- /* This means word length is 16 bit. Refer to IEC60958-3 page 12.
*/
- aud_schnl_8 |= 2 << HDMI_FC_AUDSCHNLS8_WORDLEGNTH_OFFSET;
- hdmi_writeb(hdmi, aud_schnl_8, HDMI_FC_AUDSCHNLS8);
+}
static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi,
unsigned long pixel_clk, unsigned int sample_rate)
{
@@ -620,6 +677,8 @@ static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi,>> hdmi->audio_cts = cts; hdmi_set_cts_n(hdmi, cts, hdmi->audio_enable ? n : 0); spin_unlock_irq(&hdmi->audio_lock);
- hdmi_set_schnl(hdmi);
}
static void hdmi_init_clk_regenerator(struct dw_hdmi *hdmi)
diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h index 6988f12d89d9..619ebc1c8354 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h @@ -158,6 +158,17 @@
#define HDMI_FC_SPDDEVICEINF 0x1062 #define HDMI_FC_AUDSCONF 0x1063 #define HDMI_FC_AUDSSTAT 0x1064
+#define HDMI_FC_AUDSV 0x1065 +#define HDMI_FC_AUDSU 0x1066 +#define HDMI_FC_AUDSCHNLS0 0x1067 +#define HDMI_FC_AUDSCHNLS1 0x1068 +#define HDMI_FC_AUDSCHNLS2 0x1069 +#define HDMI_FC_AUDSCHNLS3 0x106a +#define HDMI_FC_AUDSCHNLS4 0x106b +#define HDMI_FC_AUDSCHNLS5 0x106c +#define HDMI_FC_AUDSCHNLS6 0x106d +#define HDMI_FC_AUDSCHNLS7 0x106e +#define HDMI_FC_AUDSCHNLS8 0x106f
#define HDMI_FC_DATACH0FILL 0x1070 #define HDMI_FC_DATACH1FILL 0x1071 #define HDMI_FC_DATACH2FILL 0x1072
@@ -706,6 +717,15 @@ enum {
/* HDMI_FC_AUDSCHNLS7 field values */
HDMI_FC_AUDSCHNLS7_ACCURACY_OFFSET = 4, HDMI_FC_AUDSCHNLS7_ACCURACY_MASK = 0x30,
- HDMI_FC_AUDSCHNLS7_SMPRATE_MASK = 0x0f,
- HDMI_FC_AUDSCHNLS7_SMPRATE_192K = 0xe,
- HDMI_FC_AUDSCHNLS7_SMPRATE_176K4 = 0xc,
- HDMI_FC_AUDSCHNLS7_SMPRATE_96K = 0xa,
- HDMI_FC_AUDSCHNLS7_SMPRATE_768K = 0x9,
- HDMI_FC_AUDSCHNLS7_SMPRATE_88K2 = 0x8,
- HDMI_FC_AUDSCHNLS7_SMPRATE_32K = 0x3,
- HDMI_FC_AUDSCHNLS7_SMPRATE_48K = 0x2,
- HDMI_FC_AUDSCHNLS7_SMPRATE_44K1 = 0x0,
/* HDMI_FC_AUDSCHNLS8 field values */
HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_MASK = 0xf0,
On Wed, Sep 4, 2019 at 2:00 AM Neil Armstrong narmstrong@baylibre.com wrote:
Hi,
Le 03/09/2019 à 11:53, Neil Armstrong a écrit :
Hi,
On 03/09/2019 07:51, Cheng-Yi Chiang wrote:
From: Yakir Yang ykk@rock-chips.com
When transmitting IEC60985 linear PCM audio, we configure the Audio Sample Channel Status information of all the channel status bits in the IEC60958 frame. Refer to 60958-3 page 10 for frequency, original frequency, and wordlength setting.
This fix the issue that audio does not come out on some monitors (e.g. LG 22CV241)
Signed-off-by: Yakir Yang ykk@rock-chips.com Signed-off-by: Cheng-Yi Chiang cychiang@chromium.org
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 59 +++++++++++++++++++++++ drivers/gpu/drm/bridge/synopsys/dw-hdmi.h | 20 ++++++++ 2 files changed, 79 insertions(+)
diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c index bd65d0479683..34d46e25d610 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c @@ -582,6 +582,63 @@ static unsigned int hdmi_compute_n(unsigned int freq, unsigned long pixel_clk) return n; }
+static void hdmi_set_schnl(struct dw_hdmi *hdmi) +{
- u8 aud_schnl_samplerate;
- u8 aud_schnl_8;
- /* These registers are on RK3288 using version 2.0a. */
- if (hdmi->version != 0x200a)
return;Are these limited to the 2.0a version *in* RK3288, or 2.0a version on all SoCs ?
After investigations, Amlogic sets these registers on their 2.0a version aswell, and Jernej (added in Cc) reported me Allwinner sets them on their < 2.0a and > 2.0a IPs versions.
Can you check on the Rockchip IP versions in RK3399 ?
Sorry, the RK3399 board I am using is using DP, not HDMI. But I found that on rockchip's tree at
https://github.com/rockchip-linux/kernel/commit/924f480383c982da9908fb96d6bb...
There is such register setting, so I think RK3399 should have the same register.
For reference, the HDMI 1.4a IP version allwinner setups is: https://github.com/Allwinner-Homlet/H3-BSP4.4-linux/blob/master/drivers/vide... (registers a "scrambled" but a custom bit can reset to the original mapping, 0x1066 ... 0x106f)
I see.. so 1.4 has this register. I can modify the check to be >= 1.4 then. Will fix in v2.
Thanks!
Neil
- switch (hdmi->sample_rate) {
- case 32000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_32K;break;- case 44100:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_44K1;break;- case 48000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_48K;break;- case 88200:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_88K2;break;- case 96000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_96K;break;- case 176400:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_176K4;break;- case 192000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_192K;break;- case 768000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_768K;break;- default:
dev_warn(hdmi->dev, "Unsupported audio sample rate (%u)\n",hdmi->sample_rate);return;- }
- /* set channel status register */
- hdmi_modb(hdmi, aud_schnl_samplerate, HDMI_FC_AUDSCHNLS7_SMPRATE_MASK,
HDMI_FC_AUDSCHNLS7);- /*
* Set original frequency to be the same as frequency.* Use one-complement value as stated in IEC60958-3 page 13.*/- aud_schnl_8 = (~aud_schnl_samplerate) <<
HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_OFFSET;- /* This means word length is 16 bit. Refer to IEC60958-3 page 12. */
- aud_schnl_8 |= 2 << HDMI_FC_AUDSCHNLS8_WORDLEGNTH_OFFSET;
- hdmi_writeb(hdmi, aud_schnl_8, HDMI_FC_AUDSCHNLS8);
+}
static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi, unsigned long pixel_clk, unsigned int sample_rate) { @@ -620,6 +677,8 @@ static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi, hdmi->audio_cts = cts; hdmi_set_cts_n(hdmi, cts, hdmi->audio_enable ? n : 0); spin_unlock_irq(&hdmi->audio_lock);
- hdmi_set_schnl(hdmi);
}
static void hdmi_init_clk_regenerator(struct dw_hdmi *hdmi) diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h index 6988f12d89d9..619ebc1c8354 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h @@ -158,6 +158,17 @@ #define HDMI_FC_SPDDEVICEINF 0x1062 #define HDMI_FC_AUDSCONF 0x1063 #define HDMI_FC_AUDSSTAT 0x1064 +#define HDMI_FC_AUDSV 0x1065 +#define HDMI_FC_AUDSU 0x1066 +#define HDMI_FC_AUDSCHNLS0 0x1067 +#define HDMI_FC_AUDSCHNLS1 0x1068 +#define HDMI_FC_AUDSCHNLS2 0x1069 +#define HDMI_FC_AUDSCHNLS3 0x106a +#define HDMI_FC_AUDSCHNLS4 0x106b +#define HDMI_FC_AUDSCHNLS5 0x106c +#define HDMI_FC_AUDSCHNLS6 0x106d +#define HDMI_FC_AUDSCHNLS7 0x106e +#define HDMI_FC_AUDSCHNLS8 0x106f #define HDMI_FC_DATACH0FILL 0x1070 #define HDMI_FC_DATACH1FILL 0x1071 #define HDMI_FC_DATACH2FILL 0x1072 @@ -706,6 +717,15 @@ enum { /* HDMI_FC_AUDSCHNLS7 field values */ HDMI_FC_AUDSCHNLS7_ACCURACY_OFFSET = 4, HDMI_FC_AUDSCHNLS7_ACCURACY_MASK = 0x30,
- HDMI_FC_AUDSCHNLS7_SMPRATE_MASK = 0x0f,
- HDMI_FC_AUDSCHNLS7_SMPRATE_192K = 0xe,
- HDMI_FC_AUDSCHNLS7_SMPRATE_176K4 = 0xc,
- HDMI_FC_AUDSCHNLS7_SMPRATE_96K = 0xa,
- HDMI_FC_AUDSCHNLS7_SMPRATE_768K = 0x9,
- HDMI_FC_AUDSCHNLS7_SMPRATE_88K2 = 0x8,
- HDMI_FC_AUDSCHNLS7_SMPRATE_32K = 0x3,
- HDMI_FC_AUDSCHNLS7_SMPRATE_48K = 0x2,
- HDMI_FC_AUDSCHNLS7_SMPRATE_44K1 = 0x0,
/* HDMI_FC_AUDSCHNLS8 field values */ HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_MASK = 0xf0,
Hi,
On Tue, Sep 3, 2019 at 5:53 PM Neil Armstrong narmstrong@baylibre.com wrote:
Hi,
On 03/09/2019 07:51, Cheng-Yi Chiang wrote:
From: Yakir Yang ykk@rock-chips.com
When transmitting IEC60985 linear PCM audio, we configure the Audio Sample Channel Status information of all the channel status bits in the IEC60958 frame. Refer to 60958-3 page 10 for frequency, original frequency, and wordlength setting.
This fix the issue that audio does not come out on some monitors (e.g. LG 22CV241)
Signed-off-by: Yakir Yang ykk@rock-chips.com Signed-off-by: Cheng-Yi Chiang cychiang@chromium.org
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 59 +++++++++++++++++++++++ drivers/gpu/drm/bridge/synopsys/dw-hdmi.h | 20 ++++++++ 2 files changed, 79 insertions(+)
diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c index bd65d0479683..34d46e25d610 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c @@ -582,6 +582,63 @@ static unsigned int hdmi_compute_n(unsigned int freq, unsigned long pixel_clk) return n; }
+static void hdmi_set_schnl(struct dw_hdmi *hdmi) +{
u8 aud_schnl_samplerate;u8 aud_schnl_8;/* These registers are on RK3288 using version 2.0a. */if (hdmi->version != 0x200a)return;Are these limited to the 2.0a version *in* RK3288, or 2.0a version on all SoCs ?
In the original patch by Yakir,
https://lore.kernel.org/patchwork/patch/539653/ (sorry, I should have added this link in the "after the cut" note)
The fix is limited to version 2.0. Since I am only testing on RK3288 with 2.0a, I change the check to 2.0a only. I can not test 2.0a version on other SoCs. The databook I have at hand is 2.0a (not specific to RK3288) so I think all 2.0a should have this register.
As for other version like version 1.3 on iMX6, there is no such register, as stated by Russell
http://lkml.iu.edu/hypermail/linux/kernel/1501.3/06268.html.
So at least we should check the version. Maybe we can set the criteria as version 2.0 or above to make it a safe patch ? If there is the same need on other SoC with version < 2.0, it can be added later. Presumably, there will be databook of that version to help confirming this setting.
Thanks!
switch (hdmi->sample_rate) {case 32000:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_32K;break;case 44100:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_44K1;break;case 48000:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_48K;break;case 88200:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_88K2;break;case 96000:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_96K;break;case 176400:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_176K4;break;case 192000:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_192K;break;case 768000:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_768K;break;default:dev_warn(hdmi->dev, "Unsupported audio sample rate (%u)\n",hdmi->sample_rate);return;}/* set channel status register */hdmi_modb(hdmi, aud_schnl_samplerate, HDMI_FC_AUDSCHNLS7_SMPRATE_MASK,HDMI_FC_AUDSCHNLS7);/** Set original frequency to be the same as frequency.* Use one-complement value as stated in IEC60958-3 page 13.*/aud_schnl_8 = (~aud_schnl_samplerate) <<HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_OFFSET;/* This means word length is 16 bit. Refer to IEC60958-3 page 12. */aud_schnl_8 |= 2 << HDMI_FC_AUDSCHNLS8_WORDLEGNTH_OFFSET;hdmi_writeb(hdmi, aud_schnl_8, HDMI_FC_AUDSCHNLS8);+}
static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi, unsigned long pixel_clk, unsigned int sample_rate) { @@ -620,6 +677,8 @@ static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi, hdmi->audio_cts = cts; hdmi_set_cts_n(hdmi, cts, hdmi->audio_enable ? n : 0); spin_unlock_irq(&hdmi->audio_lock);
hdmi_set_schnl(hdmi);}
static void hdmi_init_clk_regenerator(struct dw_hdmi *hdmi) diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h index 6988f12d89d9..619ebc1c8354 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h @@ -158,6 +158,17 @@ #define HDMI_FC_SPDDEVICEINF 0x1062 #define HDMI_FC_AUDSCONF 0x1063 #define HDMI_FC_AUDSSTAT 0x1064 +#define HDMI_FC_AUDSV 0x1065 +#define HDMI_FC_AUDSU 0x1066 +#define HDMI_FC_AUDSCHNLS0 0x1067 +#define HDMI_FC_AUDSCHNLS1 0x1068 +#define HDMI_FC_AUDSCHNLS2 0x1069 +#define HDMI_FC_AUDSCHNLS3 0x106a +#define HDMI_FC_AUDSCHNLS4 0x106b +#define HDMI_FC_AUDSCHNLS5 0x106c +#define HDMI_FC_AUDSCHNLS6 0x106d +#define HDMI_FC_AUDSCHNLS7 0x106e +#define HDMI_FC_AUDSCHNLS8 0x106f #define HDMI_FC_DATACH0FILL 0x1070 #define HDMI_FC_DATACH1FILL 0x1071 #define HDMI_FC_DATACH2FILL 0x1072 @@ -706,6 +717,15 @@ enum { /* HDMI_FC_AUDSCHNLS7 field values */ HDMI_FC_AUDSCHNLS7_ACCURACY_OFFSET = 4, HDMI_FC_AUDSCHNLS7_ACCURACY_MASK = 0x30,
HDMI_FC_AUDSCHNLS7_SMPRATE_MASK = 0x0f,HDMI_FC_AUDSCHNLS7_SMPRATE_192K = 0xe,HDMI_FC_AUDSCHNLS7_SMPRATE_176K4 = 0xc,HDMI_FC_AUDSCHNLS7_SMPRATE_96K = 0xa,HDMI_FC_AUDSCHNLS7_SMPRATE_768K = 0x9,HDMI_FC_AUDSCHNLS7_SMPRATE_88K2 = 0x8,HDMI_FC_AUDSCHNLS7_SMPRATE_32K = 0x3,HDMI_FC_AUDSCHNLS7_SMPRATE_48K = 0x2,HDMI_FC_AUDSCHNLS7_SMPRATE_44K1 = 0x0,/* HDMI_FC_AUDSCHNLS8 field values */ HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_MASK = 0xf0,
On Wed, Sep 04, 2019 at 05:09:29PM +0800, Cheng-yi Chiang wrote:
Hi,
On Tue, Sep 3, 2019 at 5:53 PM Neil Armstrong narmstrong@baylibre.com wrote:
Hi,
On 03/09/2019 07:51, Cheng-Yi Chiang wrote:
From: Yakir Yang ykk@rock-chips.com
When transmitting IEC60985 linear PCM audio, we configure the Audio Sample Channel Status information of all the channel status bits in the IEC60958 frame. Refer to 60958-3 page 10 for frequency, original frequency, and wordlength setting.
This fix the issue that audio does not come out on some monitors (e.g. LG 22CV241)
Signed-off-by: Yakir Yang ykk@rock-chips.com Signed-off-by: Cheng-Yi Chiang cychiang@chromium.org
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 59 +++++++++++++++++++++++ drivers/gpu/drm/bridge/synopsys/dw-hdmi.h | 20 ++++++++ 2 files changed, 79 insertions(+)
diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c index bd65d0479683..34d46e25d610 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c @@ -582,6 +582,63 @@ static unsigned int hdmi_compute_n(unsigned int freq, unsigned long pixel_clk) return n; }
+static void hdmi_set_schnl(struct dw_hdmi *hdmi) +{
u8 aud_schnl_samplerate;u8 aud_schnl_8;/* These registers are on RK3288 using version 2.0a. */if (hdmi->version != 0x200a)return;Are these limited to the 2.0a version *in* RK3288, or 2.0a version on all SoCs ?
In the original patch by Yakir,
https://lore.kernel.org/patchwork/patch/539653/ (sorry, I should have added this link in the "after the cut" note)
The fix is limited to version 2.0. Since I am only testing on RK3288 with 2.0a, I change the check to 2.0a only. I can not test 2.0a version on other SoCs. The databook I have at hand is 2.0a (not specific to RK3288) so I think all 2.0a should have this register.
As for other version like version 1.3 on iMX6, there is no such register, as stated by Russell
http://lkml.iu.edu/hypermail/linux/kernel/1501.3/06268.html.
It's likely more to do with how the IP is configured rather than the version. The big difference between dw-hdmi used in iMX6 and elsewhere is that iMX6 uses a built-in AHB audio interface and not I2S. Elsewhere uses I2S.
I2S does not have the capability to convey channel status information (which is required by HDMI). With AHB, it is encoded into the data in memory.
So, I think this setup should be done in the I2S driver and not in the core driver.
Hi,
On 04/09/2019 11:09, Cheng-yi Chiang wrote:
Hi,
On Tue, Sep 3, 2019 at 5:53 PM Neil Armstrong narmstrong@baylibre.com wrote:
Hi,
On 03/09/2019 07:51, Cheng-Yi Chiang wrote:
From: Yakir Yang ykk@rock-chips.com
When transmitting IEC60985 linear PCM audio, we configure the Audio Sample Channel Status information of all the channel status bits in the IEC60958 frame. Refer to 60958-3 page 10 for frequency, original frequency, and wordlength setting.
This fix the issue that audio does not come out on some monitors (e.g. LG 22CV241)
Signed-off-by: Yakir Yang ykk@rock-chips.com Signed-off-by: Cheng-Yi Chiang cychiang@chromium.org
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 59 +++++++++++++++++++++++ drivers/gpu/drm/bridge/synopsys/dw-hdmi.h | 20 ++++++++ 2 files changed, 79 insertions(+)
diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c index bd65d0479683..34d46e25d610 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c @@ -582,6 +582,63 @@ static unsigned int hdmi_compute_n(unsigned int freq, unsigned long pixel_clk) return n; }
+static void hdmi_set_schnl(struct dw_hdmi *hdmi) +{
u8 aud_schnl_samplerate;u8 aud_schnl_8;/* These registers are on RK3288 using version 2.0a. */if (hdmi->version != 0x200a)return;Are these limited to the 2.0a version *in* RK3288, or 2.0a version on all SoCs ?
In the original patch by Yakir,
https://lore.kernel.org/patchwork/patch/539653/ (sorry, I should have added this link in the "after the cut" note)
The fix is limited to version 2.0. Since I am only testing on RK3288 with 2.0a, I change the check to 2.0a only. I can not test 2.0a version on other SoCs. The databook I have at hand is 2.0a (not specific to RK3288) so I think all 2.0a should have this register.
As for other version like version 1.3 on iMX6, there is no such register, as stated by Russell
http://lkml.iu.edu/hypermail/linux/kernel/1501.3/06268.html.
Russell assumes the registers are not present on the iMX6 IP not having the I2S registers, but they are present on the IPs configured with I2S at any versions.
My databook version (1.40.a) specifies :
fc_audschnls0 to fc_audschnls8
``` When transmitting IEC60958 linear PCM audio, this registers allow to configure the channel status information of all the channel status bits in the IEC60958 frame. For the moment this configuration is only used when the I2S audio interface, General Purpose Audio (GPA), or AHB audio DMA (AHBAUDDMA) interface is active (for S/PDIF interface this information comes from the stream). ```
But the databook Revision History shows these registers were present since version 1.10a.
I propose you remove the version check, but you only setup these registers when I2S is enabled: (hdmi_readb(hdmi, HDMI_CONFIG0_ID) & HDMI_CONFIG0_I2S) until a AHBAUDDMA user needs this, with a small comment explaining the situation.
Neil
So at least we should check the version. Maybe we can set the criteria as version 2.0 or above to make it a safe patch ? If there is the same need on other SoC with version < 2.0, it can be added later. Presumably, there will be databook of that version to help confirming this setting.
Thanks!
switch (hdmi->sample_rate) {case 32000:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_32K;break;case 44100:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_44K1;break;case 48000:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_48K;break;case 88200:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_88K2;break;case 96000:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_96K;break;case 176400:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_176K4;break;case 192000:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_192K;break;case 768000:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_768K;break;default:dev_warn(hdmi->dev, "Unsupported audio sample rate (%u)\n",hdmi->sample_rate);return;}/* set channel status register */hdmi_modb(hdmi, aud_schnl_samplerate, HDMI_FC_AUDSCHNLS7_SMPRATE_MASK,HDMI_FC_AUDSCHNLS7);/** Set original frequency to be the same as frequency.* Use one-complement value as stated in IEC60958-3 page 13.*/aud_schnl_8 = (~aud_schnl_samplerate) <<HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_OFFSET;/* This means word length is 16 bit. Refer to IEC60958-3 page 12. */aud_schnl_8 |= 2 << HDMI_FC_AUDSCHNLS8_WORDLEGNTH_OFFSET;hdmi_writeb(hdmi, aud_schnl_8, HDMI_FC_AUDSCHNLS8);+}
static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi, unsigned long pixel_clk, unsigned int sample_rate) { @@ -620,6 +677,8 @@ static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi, hdmi->audio_cts = cts; hdmi_set_cts_n(hdmi, cts, hdmi->audio_enable ? n : 0); spin_unlock_irq(&hdmi->audio_lock);
hdmi_set_schnl(hdmi);}
static void hdmi_init_clk_regenerator(struct dw_hdmi *hdmi) diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h index 6988f12d89d9..619ebc1c8354 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h @@ -158,6 +158,17 @@ #define HDMI_FC_SPDDEVICEINF 0x1062 #define HDMI_FC_AUDSCONF 0x1063 #define HDMI_FC_AUDSSTAT 0x1064 +#define HDMI_FC_AUDSV 0x1065 +#define HDMI_FC_AUDSU 0x1066 +#define HDMI_FC_AUDSCHNLS0 0x1067 +#define HDMI_FC_AUDSCHNLS1 0x1068 +#define HDMI_FC_AUDSCHNLS2 0x1069 +#define HDMI_FC_AUDSCHNLS3 0x106a +#define HDMI_FC_AUDSCHNLS4 0x106b +#define HDMI_FC_AUDSCHNLS5 0x106c +#define HDMI_FC_AUDSCHNLS6 0x106d +#define HDMI_FC_AUDSCHNLS7 0x106e +#define HDMI_FC_AUDSCHNLS8 0x106f #define HDMI_FC_DATACH0FILL 0x1070 #define HDMI_FC_DATACH1FILL 0x1071 #define HDMI_FC_DATACH2FILL 0x1072 @@ -706,6 +717,15 @@ enum { /* HDMI_FC_AUDSCHNLS7 field values */ HDMI_FC_AUDSCHNLS7_ACCURACY_OFFSET = 4, HDMI_FC_AUDSCHNLS7_ACCURACY_MASK = 0x30,
HDMI_FC_AUDSCHNLS7_SMPRATE_MASK = 0x0f,HDMI_FC_AUDSCHNLS7_SMPRATE_192K = 0xe,HDMI_FC_AUDSCHNLS7_SMPRATE_176K4 = 0xc,HDMI_FC_AUDSCHNLS7_SMPRATE_96K = 0xa,HDMI_FC_AUDSCHNLS7_SMPRATE_768K = 0x9,HDMI_FC_AUDSCHNLS7_SMPRATE_88K2 = 0x8,HDMI_FC_AUDSCHNLS7_SMPRATE_32K = 0x3,HDMI_FC_AUDSCHNLS7_SMPRATE_48K = 0x2,HDMI_FC_AUDSCHNLS7_SMPRATE_44K1 = 0x0,/* HDMI_FC_AUDSCHNLS8 field values */ HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_MASK = 0xf0,
On Wed, Sep 4, 2019 at 5:28 PM Neil Armstrong narmstrong@baylibre.com wrote:
Hi,
On 04/09/2019 11:09, Cheng-yi Chiang wrote:
Hi,
On Tue, Sep 3, 2019 at 5:53 PM Neil Armstrong narmstrong@baylibre.com wrote:
Hi,
On 03/09/2019 07:51, Cheng-Yi Chiang wrote:
From: Yakir Yang ykk@rock-chips.com
When transmitting IEC60985 linear PCM audio, we configure the Audio Sample Channel Status information of all the channel status bits in the IEC60958 frame. Refer to 60958-3 page 10 for frequency, original frequency, and wordlength setting.
This fix the issue that audio does not come out on some monitors (e.g. LG 22CV241)
Signed-off-by: Yakir Yang ykk@rock-chips.com Signed-off-by: Cheng-Yi Chiang cychiang@chromium.org
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 59 +++++++++++++++++++++++ drivers/gpu/drm/bridge/synopsys/dw-hdmi.h | 20 ++++++++ 2 files changed, 79 insertions(+)
diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c index bd65d0479683..34d46e25d610 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c @@ -582,6 +582,63 @@ static unsigned int hdmi_compute_n(unsigned int freq, unsigned long pixel_clk) return n; }
+static void hdmi_set_schnl(struct dw_hdmi *hdmi) +{
u8 aud_schnl_samplerate;u8 aud_schnl_8;/* These registers are on RK3288 using version 2.0a. */if (hdmi->version != 0x200a)return;Are these limited to the 2.0a version *in* RK3288, or 2.0a version on all SoCs ?
In the original patch by Yakir,
https://lore.kernel.org/patchwork/patch/539653/ (sorry, I should have added this link in the "after the cut" note)
The fix is limited to version 2.0. Since I am only testing on RK3288 with 2.0a, I change the check to 2.0a only. I can not test 2.0a version on other SoCs. The databook I have at hand is 2.0a (not specific to RK3288) so I think all 2.0a should have this register.
As for other version like version 1.3 on iMX6, there is no such register, as stated by Russell
http://lkml.iu.edu/hypermail/linux/kernel/1501.3/06268.html.
Russell assumes the registers are not present on the iMX6 IP not having the I2S registers, but they are present on the IPs configured with I2S at any versions.
I see. Thanks for the check.
My databook version (1.40.a) specifies :
fc_audschnls0 to fc_audschnls8
When transmitting IEC60958 linear PCM audio, this registers allow to configure the channel status information of all the channel status bits in the IEC60958 frame. For the moment this configuration is only used when the I2S audio interface, General Purpose Audio (GPA), or AHB audio DMA (AHBAUDDMA) interface is active (for S/PDIF interface this information comes from the stream).But the databook Revision History shows these registers were present since version 1.10a.
I propose you remove the version check, but you only setup these registers when I2S is enabled: (hdmi_readb(hdmi, HDMI_CONFIG0_ID) & HDMI_CONFIG0_I2S) until a AHBAUDDMA user needs this, with a small comment explaining the situation.
I see. Sound like a good plan. In sum, I will add set_channel_status() in dw_hdmi.c And in the beginning of this function, check it is using I2S (hdmi_readb(hdmi, HDMI_CONFIG0_ID) & HDMI_CONFIG0_I2S) with a comment explaining the situation.
And let dw-hdmi-audio-i2s dw_hdmi_i2s_hw_params() to call this function after dw_hdmi_set_sample_rate, with word length (or sample_bit) passed it as argument. I have not tested setting this register here as in the original patch it was set in hdmi_set_clk_regenerator. I will test it and update in my v2.
Thanks again to everyone for the prompt reply and help.
Neil
So at least we should check the version. Maybe we can set the criteria as version 2.0 or above to make it a safe patch ? If there is the same need on other SoC with version < 2.0, it can be added later. Presumably, there will be databook of that version to help confirming this setting.
Thanks!
switch (hdmi->sample_rate) {case 32000:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_32K;break;case 44100:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_44K1;break;case 48000:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_48K;break;case 88200:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_88K2;break;case 96000:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_96K;break;case 176400:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_176K4;break;case 192000:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_192K;break;case 768000:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_768K;break;default:dev_warn(hdmi->dev, "Unsupported audio sample rate (%u)\n",hdmi->sample_rate);return;}/* set channel status register */hdmi_modb(hdmi, aud_schnl_samplerate, HDMI_FC_AUDSCHNLS7_SMPRATE_MASK,HDMI_FC_AUDSCHNLS7);/** Set original frequency to be the same as frequency.* Use one-complement value as stated in IEC60958-3 page 13.*/aud_schnl_8 = (~aud_schnl_samplerate) <<HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_OFFSET;/* This means word length is 16 bit. Refer to IEC60958-3 page 12. */aud_schnl_8 |= 2 << HDMI_FC_AUDSCHNLS8_WORDLEGNTH_OFFSET;hdmi_writeb(hdmi, aud_schnl_8, HDMI_FC_AUDSCHNLS8);+}
static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi, unsigned long pixel_clk, unsigned int sample_rate) { @@ -620,6 +677,8 @@ static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi, hdmi->audio_cts = cts; hdmi_set_cts_n(hdmi, cts, hdmi->audio_enable ? n : 0); spin_unlock_irq(&hdmi->audio_lock);
hdmi_set_schnl(hdmi);}
static void hdmi_init_clk_regenerator(struct dw_hdmi *hdmi) diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h index 6988f12d89d9..619ebc1c8354 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h @@ -158,6 +158,17 @@ #define HDMI_FC_SPDDEVICEINF 0x1062 #define HDMI_FC_AUDSCONF 0x1063 #define HDMI_FC_AUDSSTAT 0x1064 +#define HDMI_FC_AUDSV 0x1065 +#define HDMI_FC_AUDSU 0x1066 +#define HDMI_FC_AUDSCHNLS0 0x1067 +#define HDMI_FC_AUDSCHNLS1 0x1068 +#define HDMI_FC_AUDSCHNLS2 0x1069 +#define HDMI_FC_AUDSCHNLS3 0x106a +#define HDMI_FC_AUDSCHNLS4 0x106b +#define HDMI_FC_AUDSCHNLS5 0x106c +#define HDMI_FC_AUDSCHNLS6 0x106d +#define HDMI_FC_AUDSCHNLS7 0x106e +#define HDMI_FC_AUDSCHNLS8 0x106f #define HDMI_FC_DATACH0FILL 0x1070 #define HDMI_FC_DATACH1FILL 0x1071 #define HDMI_FC_DATACH2FILL 0x1072 @@ -706,6 +717,15 @@ enum { /* HDMI_FC_AUDSCHNLS7 field values */ HDMI_FC_AUDSCHNLS7_ACCURACY_OFFSET = 4, HDMI_FC_AUDSCHNLS7_ACCURACY_MASK = 0x30,
HDMI_FC_AUDSCHNLS7_SMPRATE_MASK = 0x0f,HDMI_FC_AUDSCHNLS7_SMPRATE_192K = 0xe,HDMI_FC_AUDSCHNLS7_SMPRATE_176K4 = 0xc,HDMI_FC_AUDSCHNLS7_SMPRATE_96K = 0xa,HDMI_FC_AUDSCHNLS7_SMPRATE_768K = 0x9,HDMI_FC_AUDSCHNLS7_SMPRATE_88K2 = 0x8,HDMI_FC_AUDSCHNLS7_SMPRATE_32K = 0x3,HDMI_FC_AUDSCHNLS7_SMPRATE_48K = 0x2,HDMI_FC_AUDSCHNLS7_SMPRATE_44K1 = 0x0,/* HDMI_FC_AUDSCHNLS8 field values */ HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_MASK = 0xf0,
On Wed, Sep 04, 2019 at 05:45:20PM +0800, Cheng-yi Chiang wrote:
On Wed, Sep 4, 2019 at 5:28 PM Neil Armstrong narmstrong@baylibre.com wrote:
Hi,
On 04/09/2019 11:09, Cheng-yi Chiang wrote:
Hi,
On Tue, Sep 3, 2019 at 5:53 PM Neil Armstrong narmstrong@baylibre.com wrote:
Hi,
On 03/09/2019 07:51, Cheng-Yi Chiang wrote:
From: Yakir Yang ykk@rock-chips.com
When transmitting IEC60985 linear PCM audio, we configure the Audio Sample Channel Status information of all the channel status bits in the IEC60958 frame. Refer to 60958-3 page 10 for frequency, original frequency, and wordlength setting.
This fix the issue that audio does not come out on some monitors (e.g. LG 22CV241)
Signed-off-by: Yakir Yang ykk@rock-chips.com Signed-off-by: Cheng-Yi Chiang cychiang@chromium.org
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 59 +++++++++++++++++++++++ drivers/gpu/drm/bridge/synopsys/dw-hdmi.h | 20 ++++++++ 2 files changed, 79 insertions(+)
diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c index bd65d0479683..34d46e25d610 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c @@ -582,6 +582,63 @@ static unsigned int hdmi_compute_n(unsigned int freq, unsigned long pixel_clk) return n; }
+static void hdmi_set_schnl(struct dw_hdmi *hdmi) +{
u8 aud_schnl_samplerate;u8 aud_schnl_8;/* These registers are on RK3288 using version 2.0a. */if (hdmi->version != 0x200a)return;Are these limited to the 2.0a version *in* RK3288, or 2.0a version on all SoCs ?
In the original patch by Yakir,
https://lore.kernel.org/patchwork/patch/539653/ (sorry, I should have added this link in the "after the cut" note)
The fix is limited to version 2.0. Since I am only testing on RK3288 with 2.0a, I change the check to 2.0a only. I can not test 2.0a version on other SoCs. The databook I have at hand is 2.0a (not specific to RK3288) so I think all 2.0a should have this register.
As for other version like version 1.3 on iMX6, there is no such register, as stated by Russell
http://lkml.iu.edu/hypermail/linux/kernel/1501.3/06268.html.
Russell assumes the registers are not present on the iMX6 IP not having the I2S registers, but they are present on the IPs configured with I2S at any versions.
I see. Thanks for the check.
My databook version (1.40.a) specifies :
fc_audschnls0 to fc_audschnls8
When transmitting IEC60958 linear PCM audio, this registers allow to configure the channel status information of all the channel status bits in the IEC60958 frame. For the moment this configuration is only used when the I2S audio interface, General Purpose Audio (GPA), or AHB audio DMA (AHBAUDDMA) interface is active (for S/PDIF interface this information comes from the stream).But the databook Revision History shows these registers were present since version 1.10a.
I propose you remove the version check, but you only setup these registers when I2S is enabled: (hdmi_readb(hdmi, HDMI_CONFIG0_ID) & HDMI_CONFIG0_I2S) until a AHBAUDDMA user needs this, with a small comment explaining the situation.
I see. Sound like a good plan. In sum, I will add set_channel_status() in dw_hdmi.c And in the beginning of this function, check it is using I2S (hdmi_readb(hdmi, HDMI_CONFIG0_ID) & HDMI_CONFIG0_I2S) with a comment explaining the situation.
And let dw-hdmi-audio-i2s dw_hdmi_i2s_hw_params() to call this function after dw_hdmi_set_sample_rate, with word length (or sample_bit) passed it as argument.
If you're going to do it this way, there's little point having the check. The dw-hdmi-audio-i2s device will only be created if that ID bit is already set. So, provided set_channel_status() (which should probably be dw_hdmi_set_channel_status()) is only called from the I2S driver, then everything should be fine without such a check. However, it is worth noting in the docbook comments above the function that it is only for I2S setups.
I have not tested setting this register here as in the original patch it was set in hdmi_set_clk_regenerator. I will test it and update in my v2.
Thanks again to everyone for the prompt reply and help.
Neil
So at least we should check the version. Maybe we can set the criteria as version 2.0 or above to make it a safe patch ? If there is the same need on other SoC with version < 2.0, it can be added later. Presumably, there will be databook of that version to help confirming this setting.
Thanks!
switch (hdmi->sample_rate) {case 32000:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_32K;break;case 44100:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_44K1;break;case 48000:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_48K;break;case 88200:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_88K2;break;case 96000:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_96K;break;case 176400:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_176K4;break;case 192000:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_192K;break;case 768000:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_768K;break;default:dev_warn(hdmi->dev, "Unsupported audio sample rate (%u)\n",hdmi->sample_rate);return;}/* set channel status register */hdmi_modb(hdmi, aud_schnl_samplerate, HDMI_FC_AUDSCHNLS7_SMPRATE_MASK,HDMI_FC_AUDSCHNLS7);/** Set original frequency to be the same as frequency.* Use one-complement value as stated in IEC60958-3 page 13.*/aud_schnl_8 = (~aud_schnl_samplerate) <<HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_OFFSET;/* This means word length is 16 bit. Refer to IEC60958-3 page 12. */aud_schnl_8 |= 2 << HDMI_FC_AUDSCHNLS8_WORDLEGNTH_OFFSET;hdmi_writeb(hdmi, aud_schnl_8, HDMI_FC_AUDSCHNLS8);+}
static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi, unsigned long pixel_clk, unsigned int sample_rate) { @@ -620,6 +677,8 @@ static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi, hdmi->audio_cts = cts; hdmi_set_cts_n(hdmi, cts, hdmi->audio_enable ? n : 0); spin_unlock_irq(&hdmi->audio_lock);
hdmi_set_schnl(hdmi);}
static void hdmi_init_clk_regenerator(struct dw_hdmi *hdmi) diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h index 6988f12d89d9..619ebc1c8354 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h @@ -158,6 +158,17 @@ #define HDMI_FC_SPDDEVICEINF 0x1062 #define HDMI_FC_AUDSCONF 0x1063 #define HDMI_FC_AUDSSTAT 0x1064 +#define HDMI_FC_AUDSV 0x1065 +#define HDMI_FC_AUDSU 0x1066 +#define HDMI_FC_AUDSCHNLS0 0x1067 +#define HDMI_FC_AUDSCHNLS1 0x1068 +#define HDMI_FC_AUDSCHNLS2 0x1069 +#define HDMI_FC_AUDSCHNLS3 0x106a +#define HDMI_FC_AUDSCHNLS4 0x106b +#define HDMI_FC_AUDSCHNLS5 0x106c +#define HDMI_FC_AUDSCHNLS6 0x106d +#define HDMI_FC_AUDSCHNLS7 0x106e +#define HDMI_FC_AUDSCHNLS8 0x106f #define HDMI_FC_DATACH0FILL 0x1070 #define HDMI_FC_DATACH1FILL 0x1071 #define HDMI_FC_DATACH2FILL 0x1072 @@ -706,6 +717,15 @@ enum { /* HDMI_FC_AUDSCHNLS7 field values */ HDMI_FC_AUDSCHNLS7_ACCURACY_OFFSET = 4, HDMI_FC_AUDSCHNLS7_ACCURACY_MASK = 0x30,
HDMI_FC_AUDSCHNLS7_SMPRATE_MASK = 0x0f,HDMI_FC_AUDSCHNLS7_SMPRATE_192K = 0xe,HDMI_FC_AUDSCHNLS7_SMPRATE_176K4 = 0xc,HDMI_FC_AUDSCHNLS7_SMPRATE_96K = 0xa,HDMI_FC_AUDSCHNLS7_SMPRATE_768K = 0x9,HDMI_FC_AUDSCHNLS7_SMPRATE_88K2 = 0x8,HDMI_FC_AUDSCHNLS7_SMPRATE_32K = 0x3,HDMI_FC_AUDSCHNLS7_SMPRATE_48K = 0x2,HDMI_FC_AUDSCHNLS7_SMPRATE_44K1 = 0x0,/* HDMI_FC_AUDSCHNLS8 field values */ HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_MASK = 0xf0,
linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
On Wed, Sep 4, 2019 at 6:32 PM Russell King - ARM Linux admin linux@armlinux.org.uk wrote:
On Wed, Sep 04, 2019 at 05:45:20PM +0800, Cheng-yi Chiang wrote:
On Wed, Sep 4, 2019 at 5:28 PM Neil Armstrong narmstrong@baylibre.com wrote:
Hi,
On 04/09/2019 11:09, Cheng-yi Chiang wrote:
Hi,
On Tue, Sep 3, 2019 at 5:53 PM Neil Armstrong narmstrong@baylibre.com wrote:
Hi,
On 03/09/2019 07:51, Cheng-Yi Chiang wrote:
From: Yakir Yang ykk@rock-chips.com
When transmitting IEC60985 linear PCM audio, we configure the Audio Sample Channel Status information of all the channel status bits in the IEC60958 frame. Refer to 60958-3 page 10 for frequency, original frequency, and wordlength setting.
This fix the issue that audio does not come out on some monitors (e.g. LG 22CV241)
Signed-off-by: Yakir Yang ykk@rock-chips.com Signed-off-by: Cheng-Yi Chiang cychiang@chromium.org
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 59 +++++++++++++++++++++++ drivers/gpu/drm/bridge/synopsys/dw-hdmi.h | 20 ++++++++ 2 files changed, 79 insertions(+)
diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c index bd65d0479683..34d46e25d610 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c @@ -582,6 +582,63 @@ static unsigned int hdmi_compute_n(unsigned int freq, unsigned long pixel_clk) return n; }
+static void hdmi_set_schnl(struct dw_hdmi *hdmi) +{
u8 aud_schnl_samplerate;u8 aud_schnl_8;/* These registers are on RK3288 using version 2.0a. */if (hdmi->version != 0x200a)return;Are these limited to the 2.0a version *in* RK3288, or 2.0a version on all SoCs ?
In the original patch by Yakir,
https://lore.kernel.org/patchwork/patch/539653/ (sorry, I should have added this link in the "after the cut" note)
The fix is limited to version 2.0. Since I am only testing on RK3288 with 2.0a, I change the check to 2.0a only. I can not test 2.0a version on other SoCs. The databook I have at hand is 2.0a (not specific to RK3288) so I think all 2.0a should have this register.
As for other version like version 1.3 on iMX6, there is no such register, as stated by Russell
http://lkml.iu.edu/hypermail/linux/kernel/1501.3/06268.html.
Russell assumes the registers are not present on the iMX6 IP not having the I2S registers, but they are present on the IPs configured with I2S at any versions.
I see. Thanks for the check.
My databook version (1.40.a) specifies :
fc_audschnls0 to fc_audschnls8
When transmitting IEC60958 linear PCM audio, this registers allow to configure the channel status information of all the channel status bits in the IEC60958 frame. For the moment this configuration is only used when the I2S audio interface, General Purpose Audio (GPA), or AHB audio DMA (AHBAUDDMA) interface is active (for S/PDIF interface this information comes from the stream).But the databook Revision History shows these registers were present since version 1.10a.
I propose you remove the version check, but you only setup these registers when I2S is enabled: (hdmi_readb(hdmi, HDMI_CONFIG0_ID) & HDMI_CONFIG0_I2S) until a AHBAUDDMA user needs this, with a small comment explaining the situation.
I see. Sound like a good plan. In sum, I will add set_channel_status() in dw_hdmi.c And in the beginning of this function, check it is using I2S (hdmi_readb(hdmi, HDMI_CONFIG0_ID) & HDMI_CONFIG0_I2S) with a comment explaining the situation.
And let dw-hdmi-audio-i2s dw_hdmi_i2s_hw_params() to call this function after dw_hdmi_set_sample_rate, with word length (or sample_bit) passed it as argument.
If you're going to do it this way, there's little point having the check. The dw-hdmi-audio-i2s device will only be created if that ID bit is already set. So, provided set_channel_status() (which should probably be dw_hdmi_set_channel_status()) is only called from the I2S driver, then everything should be fine without such a check. However, it is worth noting in the docbook comments above the function that it is only for I2S setups.
I see. Yes it is simpler. Thanks for the suggestion! Will fix in v2.
I have not tested setting this register here as in the original patch it was set in hdmi_set_clk_regenerator. I will test it and update in my v2.
Thanks again to everyone for the prompt reply and help.
Neil
So at least we should check the version. Maybe we can set the criteria as version 2.0 or above to make it a safe patch ? If there is the same need on other SoC with version < 2.0, it can be added later. Presumably, there will be databook of that version to help confirming this setting.
Thanks!
switch (hdmi->sample_rate) {case 32000:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_32K;break;case 44100:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_44K1;break;case 48000:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_48K;break;case 88200:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_88K2;break;case 96000:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_96K;break;case 176400:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_176K4;break;case 192000:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_192K;break;case 768000:aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_768K;break;default:dev_warn(hdmi->dev, "Unsupported audio sample rate (%u)\n",hdmi->sample_rate);return;}/* set channel status register */hdmi_modb(hdmi, aud_schnl_samplerate, HDMI_FC_AUDSCHNLS7_SMPRATE_MASK,HDMI_FC_AUDSCHNLS7);/** Set original frequency to be the same as frequency.* Use one-complement value as stated in IEC60958-3 page 13.*/aud_schnl_8 = (~aud_schnl_samplerate) <<HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_OFFSET;/* This means word length is 16 bit. Refer to IEC60958-3 page 12. */aud_schnl_8 |= 2 << HDMI_FC_AUDSCHNLS8_WORDLEGNTH_OFFSET;hdmi_writeb(hdmi, aud_schnl_8, HDMI_FC_AUDSCHNLS8);+}
static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi, unsigned long pixel_clk, unsigned int sample_rate) { @@ -620,6 +677,8 @@ static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi, hdmi->audio_cts = cts; hdmi_set_cts_n(hdmi, cts, hdmi->audio_enable ? n : 0); spin_unlock_irq(&hdmi->audio_lock);
hdmi_set_schnl(hdmi);}
static void hdmi_init_clk_regenerator(struct dw_hdmi *hdmi) diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h index 6988f12d89d9..619ebc1c8354 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h @@ -158,6 +158,17 @@ #define HDMI_FC_SPDDEVICEINF 0x1062 #define HDMI_FC_AUDSCONF 0x1063 #define HDMI_FC_AUDSSTAT 0x1064 +#define HDMI_FC_AUDSV 0x1065 +#define HDMI_FC_AUDSU 0x1066 +#define HDMI_FC_AUDSCHNLS0 0x1067 +#define HDMI_FC_AUDSCHNLS1 0x1068 +#define HDMI_FC_AUDSCHNLS2 0x1069 +#define HDMI_FC_AUDSCHNLS3 0x106a +#define HDMI_FC_AUDSCHNLS4 0x106b +#define HDMI_FC_AUDSCHNLS5 0x106c +#define HDMI_FC_AUDSCHNLS6 0x106d +#define HDMI_FC_AUDSCHNLS7 0x106e +#define HDMI_FC_AUDSCHNLS8 0x106f #define HDMI_FC_DATACH0FILL 0x1070 #define HDMI_FC_DATACH1FILL 0x1071 #define HDMI_FC_DATACH2FILL 0x1072 @@ -706,6 +717,15 @@ enum { /* HDMI_FC_AUDSCHNLS7 field values */ HDMI_FC_AUDSCHNLS7_ACCURACY_OFFSET = 4, HDMI_FC_AUDSCHNLS7_ACCURACY_MASK = 0x30,
HDMI_FC_AUDSCHNLS7_SMPRATE_MASK = 0x0f,HDMI_FC_AUDSCHNLS7_SMPRATE_192K = 0xe,HDMI_FC_AUDSCHNLS7_SMPRATE_176K4 = 0xc,HDMI_FC_AUDSCHNLS7_SMPRATE_96K = 0xa,HDMI_FC_AUDSCHNLS7_SMPRATE_768K = 0x9,HDMI_FC_AUDSCHNLS7_SMPRATE_88K2 = 0x8,HDMI_FC_AUDSCHNLS7_SMPRATE_32K = 0x3,HDMI_FC_AUDSCHNLS7_SMPRATE_48K = 0x2,HDMI_FC_AUDSCHNLS7_SMPRATE_44K1 = 0x0,/* HDMI_FC_AUDSCHNLS8 field values */ HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_MASK = 0xf0,
linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
-- RMK's Patch system: https://www.armlinux.org.uk/developer/patches/ FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up According to speedtest.net: 11.9Mbps down 500kbps up
dri-devel@lists.freedesktop.org
-
Cheng-Yi Chiang -
Cheng-yi Chiang
-
Jernej Škrabec -
Jonas Karlman -
Neil Armstrong -
Russell King - ARM Linux admin