Hi Archit,
Sorry for spamming, forgot to add the list.
This quite big patchset adds support for 4K Ultra HD modes in SiI8620 MHL bridge. To support it full MHL3 protocol and its sub-protocols should be implemented. Patchset contains also various fixes for bugs discovered during development.
v3: - upper-cased enums - add missing include to patch 6 (thanks to kbuild test robot)
Regards Andrzej
Andrzej Hajda (25): drm/bridge/sii8620: simplify MHL3 mode setting drm/bridge/sii8620: add MHL3 mode check helper drm/bridge/sii8620: add reading device capability registers drm/bridge/sii8620: add continuations to messages drm/bridge/sii8620: initial support for eCBUS-S mode drm/bridge/mhl: add write burst related definitions drm/bridge/sii8620: add support for burst eMSC transmissions drm/bridge/sii8620: respond to feature requests drm/bridge/sii8620: fix peer device capabilities read code drm/bridge/sii8620: remove spare CBUS bring-up sequence drm/bridge/sii8620: fix MSC message removal drm/bridge/sii8620: fix initialization sequence for MHL2 receivers drm/bridge/sii8620: abstract out sink detection code drm/bridge/sii8620: set gen2 write burst before sending MSC command drm/bridge/sii8620: do not stop MHL output when TMDS input is stopped drm/bridge/sii8620: add delay during cbus reset drm/bridge/sii8620: split EDID read and write code drm/bridge/sii8620: fix disconnect sequence drm/bridge/mhl: add MHL3 infoframe related definitions drm/bridge/sii8620: rewrite hdmi start sequence drm/bridge/sii8620: send EMSC features on request drm/bridge/sii8620: improve gen2 write burst IRQ routine drm/bridge/sii8620: add HSIC initialization code drm/bridge/sii8620: enable MHL3 mode if possible drm/bridge/sii8620: enable interlace modes
drivers/gpu/drm/bridge/sil-sii8620.c | 948 ++++++++++++++++++++++++++++++----- drivers/gpu/drm/bridge/sil-sii8620.h | 50 +- include/drm/bridge/mhl.h | 85 ++++ 3 files changed, 933 insertions(+), 150 deletions(-)
It is not necessary to set REG_COC_CTL0, REG_MHL_COC_CTL1 registers.
Signed-off-by: Andrzej Hajda a.hajda@samsung.com --- drivers/gpu/drm/bridge/sil-sii8620.c | 8 ++------ 1 file changed, 2 insertions(+), 6 deletions(-)
diff --git a/drivers/gpu/drm/bridge/sil-sii8620.c b/drivers/gpu/drm/bridge/sil-sii8620.c index b2c267d..68cdf63 100644 --- a/drivers/gpu/drm/bridge/sil-sii8620.c +++ b/drivers/gpu/drm/bridge/sil-sii8620.c @@ -974,12 +974,8 @@ static void sii8620_set_mode(struct sii8620 *ctx, enum sii8620_mode mode) ); break; case CM_MHL3: - sii8620_write_seq_static(ctx, - REG_M3_CTRL, VAL_M3_CTRL_MHL3_VALUE, - REG_COC_CTL0, 0x40, - REG_MHL_COC_CTL1, 0x07 - ); - break; + sii8620_write(ctx, REG_M3_CTRL, VAL_M3_CTRL_MHL3_VALUE); + return; case CM_DISCONNECTED: break; default:
MHL3 modes differs significantly from MHL1 mode, this helper will be used frequently to clearly distinguish them.
Signed-off-by: Andrzej Hajda a.hajda@samsung.com --- drivers/gpu/drm/bridge/sil-sii8620.c | 9 +++++++-- 1 file changed, 7 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/bridge/sil-sii8620.c b/drivers/gpu/drm/bridge/sil-sii8620.c index 68cdf63..50af78f 100644 --- a/drivers/gpu/drm/bridge/sil-sii8620.c +++ b/drivers/gpu/drm/bridge/sil-sii8620.c @@ -227,6 +227,11 @@ static void sii8620_setbits(struct sii8620 *ctx, u16 addr, u8 mask, u8 val) sii8620_write(ctx, addr, val); }
+static inline bool sii8620_is_mhl3(struct sii8620 *ctx) +{ + return ctx->mode >= CM_MHL3; +} + static void sii8620_mt_cleanup(struct sii8620 *ctx) { struct sii8620_mt_msg *msg, *n; @@ -724,7 +729,7 @@ static void sii8620_start_hdmi(struct sii8620 *ctx)
static void sii8620_start_video(struct sii8620 *ctx) { - if (ctx->mode < CM_MHL3) + if (!sii8620_is_mhl3(ctx)) sii8620_stop_video(ctx);
switch (ctx->sink_type) { @@ -838,7 +843,7 @@ static void sii8620_mhl_discover(struct sii8620 *ctx)
static void sii8620_peer_specific_init(struct sii8620 *ctx) { - if (ctx->mode == CM_MHL3) + if (sii8620_is_mhl3(ctx)) sii8620_write_seq_static(ctx, REG_SYS_CTRL1, BIT_SYS_CTRL1_BLOCK_DDC_BY_HPD, REG_EMSCINTRMASK1,
This functionality is necessary to implement MHL3 modes.
Signed-off-by: Andrzej Hajda a.hajda@samsung.com --- drivers/gpu/drm/bridge/sil-sii8620.c | 35 +++++++++++++++++++++++++++++++++++ 1 file changed, 35 insertions(+)
diff --git a/drivers/gpu/drm/bridge/sil-sii8620.c b/drivers/gpu/drm/bridge/sil-sii8620.c index 50af78f..75867c0 100644 --- a/drivers/gpu/drm/bridge/sil-sii8620.c +++ b/drivers/gpu/drm/bridge/sil-sii8620.c @@ -286,6 +286,12 @@ static void sii8620_mt_msc_cmd_send(struct sii8620 *ctx, sii8620_write(ctx, REG_MSC_COMMAND_START, BIT_MSC_COMMAND_START_MSC_MSG); break; + case MHL_READ_DEVCAP_REG: + case MHL_READ_XDEVCAP_REG: + sii8620_write(ctx, REG_MSC_CMD_OR_OFFSET, msg->reg[1]); + sii8620_write(ctx, REG_MSC_COMMAND_START, + BIT_MSC_COMMAND_START_READ_DEVCAP); + break; default: dev_err(ctx->dev, "%s: command %#x not supported\n", __func__, msg->reg[0]); @@ -455,6 +461,35 @@ static void sii8620_mt_read_devcap(struct sii8620 *ctx, bool xdevcap) msg->recv = sii8620_mt_read_devcap_recv; }
+static void sii8620_mt_read_devcap_reg_recv(struct sii8620 *ctx, + struct sii8620_mt_msg *msg) +{ + u8 reg = msg->reg[0] & 0x7f; + + if (msg->reg[0] & 0x80) + ctx->xdevcap[reg] = msg->ret; + else + ctx->devcap[reg] = msg->ret; +} + +static void sii8620_mt_read_devcap_reg(struct sii8620 *ctx, u8 reg) +{ + struct sii8620_mt_msg *msg = sii8620_mt_msg_new(ctx); + + if (!msg) + return; + + msg->reg[0] = (reg & 0x80) ? MHL_READ_XDEVCAP_REG : MHL_READ_DEVCAP_REG; + msg->reg[1] = reg; + msg->send = sii8620_mt_msc_cmd_send; + msg->recv = sii8620_mt_read_devcap_reg_recv; +} + +static inline void sii8620_mt_read_xdevcap_reg(struct sii8620 *ctx, u8 reg) +{ + sii8620_mt_read_devcap_reg(ctx, reg | 0x80); +} + static void sii8620_fetch_edid(struct sii8620 *ctx) { u8 lm_ddc, ddc_cmd, int3, cbus;
Due to asynchronous nature of MHL flow of execution is dispersed. Logical continuation of some actions happens after response of peer, i.e in interrupt handler. To simplify coding continuation mechanism has been added - it is now possible to provide continuation callback, which will be called after peer responds to given action.
Signed-off-by: Andrzej Hajda a.hajda@samsung.com --- drivers/gpu/drm/bridge/sil-sii8620.c | 20 ++++++++++++++++++++ 1 file changed, 20 insertions(+)
diff --git a/drivers/gpu/drm/bridge/sil-sii8620.c b/drivers/gpu/drm/bridge/sil-sii8620.c index 75867c0..cde0074 100644 --- a/drivers/gpu/drm/bridge/sil-sii8620.c +++ b/drivers/gpu/drm/bridge/sil-sii8620.c @@ -78,12 +78,15 @@ struct sii8620_mt_msg; typedef void (*sii8620_mt_msg_cb)(struct sii8620 *ctx, struct sii8620_mt_msg *msg);
+typedef void (*sii8620_cb)(struct sii8620 *ctx, int ret); + struct sii8620_mt_msg { struct list_head node; u8 reg[4]; u8 ret; sii8620_mt_msg_cb send; sii8620_mt_msg_cb recv; + sii8620_cb continuation; };
static const u8 sii8620_i2c_page[] = { @@ -258,6 +261,8 @@ static void sii8620_mt_work(struct sii8620 *ctx) node); if (msg->recv) msg->recv(ctx, msg); + if (msg->continuation) + msg->continuation(ctx, msg->ret); list_del(&msg->node); kfree(msg); } @@ -310,6 +315,21 @@ static struct sii8620_mt_msg *sii8620_mt_msg_new(struct sii8620 *ctx) return msg; }
+static void sii8620_mt_set_cont(struct sii8620 *ctx, sii8620_cb cont) +{ + struct sii8620_mt_msg *msg; + + if (ctx->error) + return; + + if (list_empty(&ctx->mt_queue)) { + ctx->error = -EINVAL; + return; + } + msg = list_last_entry(&ctx->mt_queue, struct sii8620_mt_msg, node); + msg->continuation = cont; +} + static void sii8620_mt_msc_cmd(struct sii8620 *ctx, u8 cmd, u8 arg1, u8 arg2) { struct sii8620_mt_msg *msg = sii8620_mt_msg_new(ctx);
The Single-ended eCBUS Mode (eCBUS-S) mode provides 60 Mb/s full-duplex bidirectional traffic for three channels: - CBUS data (CBUS1 channel), - High-bandwidth MHL data (eMSC channel), - tunneling data (T-CBUS channel). It is required to fully support MHL3 dongles.
Signed-off-by: Andrzej Hajda a.hajda@samsung.com --- drivers/gpu/drm/bridge/sil-sii8620.c | 104 ++++++++++++++++++++++++++++++++++- drivers/gpu/drm/bridge/sil-sii8620.h | 5 ++ 2 files changed, 107 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/bridge/sil-sii8620.c b/drivers/gpu/drm/bridge/sil-sii8620.c index cde0074..0d3716f 100644 --- a/drivers/gpu/drm/bridge/sil-sii8620.c +++ b/drivers/gpu/drm/bridge/sil-sii8620.c @@ -104,6 +104,7 @@ static void sii8620_fetch_edid(struct sii8620 *ctx); static void sii8620_set_upstream_edid(struct sii8620 *ctx); static void sii8620_enable_hpd(struct sii8620 *ctx); static void sii8620_mhl_disconnected(struct sii8620 *ctx); +static void sii8620_disconnect(struct sii8620 *ctx);
static int sii8620_clear_error(struct sii8620 *ctx) { @@ -1016,13 +1017,44 @@ static void sii8620_mhl_init(struct sii8620 *ctx) sii8620_mt_set_int(ctx, MHL_INT_REG(RCHANGE), MHL_INT_RC_DCAP_CHG); }
+static void sii8620_emsc_enable(struct sii8620 *ctx) +{ + u8 reg; + + sii8620_setbits(ctx, REG_GENCTL, BIT_GENCTL_EMSC_EN + | BIT_GENCTL_CLR_EMSC_RFIFO + | BIT_GENCTL_CLR_EMSC_XFIFO, ~0); + sii8620_setbits(ctx, REG_GENCTL, BIT_GENCTL_CLR_EMSC_RFIFO + | BIT_GENCTL_CLR_EMSC_XFIFO, 0); + sii8620_setbits(ctx, REG_COMMECNT, BIT_COMMECNT_I2C_TO_EMSC_EN, ~0); + reg = sii8620_readb(ctx, REG_EMSCINTR); + sii8620_write(ctx, REG_EMSCINTR, reg); + sii8620_write(ctx, REG_EMSCINTRMASK, BIT_EMSCINTR_SPI_DVLD); +} + +static int sii8620_wait_for_fsm_state(struct sii8620 *ctx, u8 state) +{ + int i; + + for (i = 0; i < 10; ++i) { + u8 s = sii8620_readb(ctx, REG_COC_STAT_0); + + if ((s & MSK_COC_STAT_0_FSM_STATE) == state) + return 0; + if (!(s & BIT_COC_STAT_0_PLL_LOCKED)) + return -EBUSY; + usleep_range(4000, 6000); + } + return -ETIMEDOUT; +} + static void sii8620_set_mode(struct sii8620 *ctx, enum sii8620_mode mode) { + int ret; + if (ctx->mode == mode) return;
- ctx->mode = mode; - switch (mode) { case CM_MHL1: sii8620_write_seq_static(ctx, @@ -1032,11 +1064,46 @@ static void sii8620_set_mode(struct sii8620 *ctx, enum sii8620_mode mode) | BIT_DPD_OSC_EN, REG_COC_INTR_MASK, 0 ); + ctx->mode = mode; break; case CM_MHL3: sii8620_write(ctx, REG_M3_CTRL, VAL_M3_CTRL_MHL3_VALUE); + ctx->mode = mode; + return; + case CM_ECBUS_S: + sii8620_emsc_enable(ctx); + sii8620_write_seq_static(ctx, + REG_TTXSPINUMS, 4, + REG_TRXSPINUMS, 4, + REG_TTXHSICNUMS, 0x14, + REG_TRXHSICNUMS, 0x14, + REG_TTXTOTNUMS, 0x18, + REG_TRXTOTNUMS, 0x18, + REG_PWD_SRST, BIT_PWD_SRST_COC_DOC_RST + | BIT_PWD_SRST_CBUS_RST_SW_EN, + REG_MHL_COC_CTL1, 0xbd, + REG_PWD_SRST, BIT_PWD_SRST_CBUS_RST_SW_EN, + REG_COC_CTLB, 0x01, + REG_COC_CTL0, 0x5c, + REG_COC_CTL14, 0x03, + REG_COC_CTL15, 0x80, + REG_MHL_DP_CTL6, BIT_MHL_DP_CTL6_DP_TAP1_SGN + | BIT_MHL_DP_CTL6_DP_TAP1_EN + | BIT_MHL_DP_CTL6_DT_PREDRV_FEEDCAP_EN, + REG_MHL_DP_CTL8, 0x03 + ); + ret = sii8620_wait_for_fsm_state(ctx, 0x03); + sii8620_write_seq_static(ctx, + REG_COC_CTL14, 0x00, + REG_COC_CTL15, 0x80 + ); + if (!ret) + sii8620_write(ctx, REG_CBUS3_CNVT, 0x85); + else + sii8620_disconnect(ctx); return; case CM_DISCONNECTED: + ctx->mode = mode; break; default: dev_err(ctx->dev, "%s mode %d not supported\n", __func__, mode); @@ -1229,12 +1296,45 @@ static void sii8620_msc_mr_write_stat(struct sii8620 *ctx) sii8620_status_changed_path(ctx); }
+static void sii8620_ecbus_up(struct sii8620 *ctx, int ret) +{ + if (ret < 0) + return; + + sii8620_set_mode(ctx, CM_ECBUS_S); +} + +static void sii8620_got_ecbus_speed(struct sii8620 *ctx, int ret) +{ + if (ret < 0) + return; + + sii8620_mt_write_stat(ctx, MHL_XDS_REG(CURR_ECBUS_MODE), + MHL_XDS_ECBUS_S | MHL_XDS_SLOT_MODE_8BIT); + sii8620_mt_rap(ctx, MHL_RAP_CBUS_MODE_UP); + sii8620_mt_set_cont(ctx, sii8620_ecbus_up); +} + static void sii8620_msc_mr_set_int(struct sii8620 *ctx) { u8 ints[MHL_INT_SIZE];
sii8620_read_buf(ctx, REG_MHL_INT_0, ints, MHL_INT_SIZE); sii8620_write_buf(ctx, REG_MHL_INT_0, ints, MHL_INT_SIZE); + + if (ints[MHL_INT_RCHANGE] & MHL_INT_RC_DCAP_CHG) { + switch (ctx->mode) { + case CM_MHL3: + sii8620_mt_read_xdevcap_reg(ctx, MHL_XDC_ECBUS_SPEEDS); + sii8620_mt_set_cont(ctx, sii8620_got_ecbus_speed); + break; + case CM_ECBUS_S: + sii8620_mt_read_devcap(ctx, true); + break; + default: + break; + } + } }
static struct sii8620_mt_msg *sii8620_msc_msg_first(struct sii8620 *ctx) diff --git a/drivers/gpu/drm/bridge/sil-sii8620.h b/drivers/gpu/drm/bridge/sil-sii8620.h index 6ff616a..3ee4e7e 100644 --- a/drivers/gpu/drm/bridge/sil-sii8620.h +++ b/drivers/gpu/drm/bridge/sil-sii8620.h @@ -841,6 +841,8 @@ #define MSK_MHL_DP_CTL7_DT_DRV_VBIAS_CASCTL 0xf0 #define MSK_MHL_DP_CTL7_DT_DRV_IREF_CTL 0x0f
+#define REG_MHL_DP_CTL8 0x0352 + /* Tx Zone Ctl1, default value: 0x00 */ #define REG_TX_ZONE_CTL1 0x0361 #define VAL_TX_ZONE_CTL1_TX_ZONE_CTRL_MODE 0x08 @@ -1088,6 +1090,9 @@
/* CoC Status, default value: 0x00 */ #define REG_COC_STAT_0 0x0700 +#define BIT_COC_STAT_0_PLL_LOCKED BIT(7) +#define MSK_COC_STAT_0_FSM_STATE 0x0f + #define REG_COC_STAT_1 0x0701 #define REG_COC_STAT_2 0x0702 #define REG_COC_STAT_3 0x0703
Burst transmissions are required in MHL3 modes.
Signed-off-by: Andrzej Hajda a.hajda@samsung.com --- include/drm/bridge/mhl.h | 53 ++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 53 insertions(+)
diff --git a/include/drm/bridge/mhl.h b/include/drm/bridge/mhl.h index 3629b27..e8d194d 100644 --- a/include/drm/bridge/mhl.h +++ b/include/drm/bridge/mhl.h @@ -15,6 +15,8 @@ #ifndef __MHL_H__ #define __MHL_H__
+#include <linux/types.h> + /* Device Capabilities Registers */ enum { MHL_DCAP_DEV_STATE, @@ -288,4 +290,55 @@ enum { /* Unsupported/unrecognized key code */ #define MHL_UCPE_STATUS_INEFFECTIVE_KEY_CODE 0x01
+enum mhl_burst_id { + MHL_BURST_ID_3D_VIC = 0x10, + MHL_BURST_ID_3D_DTD = 0x11, + MHL_BURST_ID_HEV_VIC = 0x20, + MHL_BURST_ID_HEV_DTDA = 0x21, + MHL_BURST_ID_HEV_DTDB = 0x22, + MHL_BURST_ID_VC_ASSIGN = 0x38, + MHL_BURST_ID_VC_CONFIRM = 0x39, + MHL_BURST_ID_AUD_DELAY = 0x40, + MHL_BURST_ID_ADT_BURSTID = 0x41, + MHL_BURST_ID_BIST_SETUP = 0x51, + MHL_BURST_ID_BIST_RETURN_STAT = 0x52, + MHL_BURST_ID_EMSC_SUPPORT = 0x61, + MHL_BURST_ID_HID_PAYLOAD = 0x62, + MHL_BURST_ID_BLK_RCV_BUFFER_INFO = 0x63, + MHL_BURST_ID_BITS_PER_PIXEL_FMT = 0x64, +}; + +struct mhl_burst_blk_rcv_buffer_info { + __be16 id; + __le16 size; +} __packed; + +struct mhl3_burst_header { + __be16 id; + u8 checksum; + u8 total_entries; + u8 sequence_index; +} __packed; + +struct mhl_burst_bits_per_pixel_fmt { + struct mhl3_burst_header hdr; + u8 num_entries; + struct { + u8 stream_id; + u8 pixel_format; + } __packed desc[0]; +} __packed; + +struct mhl_burst_emsc_support { + struct mhl3_burst_header hdr; + u8 num_entries; + __be16 burst_id[0]; +} __packed; + +struct mhl_burst_audio_descr { + struct mhl3_burst_header hdr; + u8 flags; + u8 short_desc[9]; +} __packed; + #endif /* __MHL_H__ */
Burst transmissions are used in MHL3 mode negotiation.
Signed-off-by: Andrzej Hajda a.hajda@samsung.com --- drivers/gpu/drm/bridge/sil-sii8620.c | 194 ++++++++++++++++++++++++++++++++++- drivers/gpu/drm/bridge/sil-sii8620.h | 4 + 2 files changed, 197 insertions(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/bridge/sil-sii8620.c b/drivers/gpu/drm/bridge/sil-sii8620.c index 0d3716f..744e685 100644 --- a/drivers/gpu/drm/bridge/sil-sii8620.c +++ b/drivers/gpu/drm/bridge/sil-sii8620.c @@ -9,6 +9,8 @@ * published by the Free Software Foundation. */
+#include <asm/unaligned.h> + #include <drm/bridge/mhl.h> #include <drm/drm_crtc.h> #include <drm/drm_edid.h> @@ -28,7 +30,8 @@
#include "sil-sii8620.h"
-#define VAL_RX_HDMI_CTRL2_DEFVAL VAL_RX_HDMI_CTRL2_IDLE_CNT(3) +#define SII8620_BURST_BUF_LEN 288 +#define VAL_RX_HDMI_CTRL2_DEFVAL VAL_RX_HDMI_CTRL2_IDLE_CNT(3)
enum sii8620_mode { CM_DISCONNECTED, @@ -71,6 +74,15 @@ struct sii8620 { unsigned int gen2_write_burst:1; enum sii8620_mt_state mt_state; struct list_head mt_queue; + struct { + int r_size; + int r_count; + int rx_ack; + int rx_count; + u8 rx_buf[32]; + int tx_count; + u8 tx_buf[32]; + } burst; };
struct sii8620_mt_msg; @@ -511,6 +523,134 @@ static inline void sii8620_mt_read_xdevcap_reg(struct sii8620 *ctx, u8 reg) sii8620_mt_read_devcap_reg(ctx, reg | 0x80); }
+static void *sii8620_burst_get_tx_buf(struct sii8620 *ctx, int len) +{ + u8 *buf = &ctx->burst.tx_buf[ctx->burst.tx_count]; + int size = len + 2; + + if (ctx->burst.tx_count + size > ARRAY_SIZE(ctx->burst.tx_buf)) { + dev_err(ctx->dev, "TX-BLK buffer exhausted\n"); + ctx->error = -EINVAL; + return NULL; + } + + ctx->burst.tx_count += size; + buf[1] = len; + + return buf + 2; +} + +static u8 *sii8620_burst_get_rx_buf(struct sii8620 *ctx, int len) +{ + u8 *buf = &ctx->burst.rx_buf[ctx->burst.rx_count]; + int size = len + 1; + + if (ctx->burst.tx_count + size > ARRAY_SIZE(ctx->burst.tx_buf)) { + dev_err(ctx->dev, "RX-BLK buffer exhausted\n"); + ctx->error = -EINVAL; + return NULL; + } + + ctx->burst.rx_count += size; + buf[0] = len; + + return buf + 1; +} + +static void sii8620_burst_send(struct sii8620 *ctx) +{ + int tx_left = ctx->burst.tx_count; + u8 *d = ctx->burst.tx_buf; + + while (tx_left > 0) { + int len = d[1] + 2; + + if (ctx->burst.r_count + len > ctx->burst.r_size) + break; + d[0] = min(ctx->burst.rx_ack, 255); + ctx->burst.rx_ack -= d[0]; + sii8620_write_buf(ctx, REG_EMSC_XMIT_WRITE_PORT, d, len); + ctx->burst.r_count += len; + tx_left -= len; + d += len; + } + + ctx->burst.tx_count = tx_left; + + while (ctx->burst.rx_ack > 0) { + u8 b[2] = { min(ctx->burst.rx_ack, 255), 0 }; + + if (ctx->burst.r_count + 2 > ctx->burst.r_size) + break; + ctx->burst.rx_ack -= b[0]; + sii8620_write_buf(ctx, REG_EMSC_XMIT_WRITE_PORT, b, 2); + ctx->burst.r_count += 2; + } +} + +static void sii8620_burst_receive(struct sii8620 *ctx) +{ + u8 buf[3], *d; + int count; + + sii8620_read_buf(ctx, REG_EMSCRFIFOBCNTL, buf, 2); + count = get_unaligned_le16(buf); + while (count > 0) { + int len = min(count, 3); + + sii8620_read_buf(ctx, REG_EMSC_RCV_READ_PORT, buf, len); + count -= len; + ctx->burst.rx_ack += len - 1; + ctx->burst.r_count -= buf[1]; + if (ctx->burst.r_count < 0) + ctx->burst.r_count = 0; + + if (len < 3 || !buf[2]) + continue; + + len = buf[2]; + d = sii8620_burst_get_rx_buf(ctx, len); + if (!d) + continue; + sii8620_read_buf(ctx, REG_EMSC_RCV_READ_PORT, d, len); + count -= len; + ctx->burst.rx_ack += len; + } +} + +static void sii8620_burst_tx_rbuf_info(struct sii8620 *ctx, int size) +{ + struct mhl_burst_blk_rcv_buffer_info *d = + sii8620_burst_get_tx_buf(ctx, sizeof(*d)); + if (!d) + return; + + d->id = cpu_to_be16(MHL_BURST_ID_BLK_RCV_BUFFER_INFO); + d->size = cpu_to_le16(size); +} + +static void sii8620_burst_rx_all(struct sii8620 *ctx) +{ + u8 *d = ctx->burst.rx_buf; + int count = ctx->burst.rx_count; + + while (count-- > 0) { + int len = *d++; + int id = get_unaligned_be16(&d[0]); + + switch (id) { + case MHL_BURST_ID_BLK_RCV_BUFFER_INFO: + ctx->burst.r_size = get_unaligned_le16(&d[2]); + break; + default: + break; + } + count -= len; + d += len; + } + ctx->burst.rx_count = 0; +} + static void sii8620_fetch_edid(struct sii8620 *ctx) { u8 lm_ddc, ddc_cmd, int3, cbus; @@ -1417,6 +1557,19 @@ static void sii8620_irq_coc(struct sii8620 *ctx) { u8 stat = sii8620_readb(ctx, REG_COC_INTR);
+ if (stat & BIT_COC_CALIBRATION_DONE) { + u8 cstat = sii8620_readb(ctx, REG_COC_STAT_0); + + cstat &= BIT_COC_STAT_0_PLL_LOCKED | MSK_COC_STAT_0_FSM_STATE; + if (cstat == (BIT_COC_STAT_0_PLL_LOCKED | 0x02)) { + sii8620_write_seq_static(ctx, + REG_COC_CTLB, 0, + REG_TRXINTMH, BIT_TDM_INTR_SYNC_DATA + | BIT_TDM_INTR_SYNC_WAIT + ); + } + } + sii8620_write(ctx, REG_COC_INTR, stat); }
@@ -1507,6 +1660,41 @@ static void sii8620_irq_infr(struct sii8620 *ctx) sii8620_start_video(ctx); }
+static void sii8620_irq_tdm(struct sii8620 *ctx) +{ + u8 stat = sii8620_readb(ctx, REG_TRXINTH); + u8 tdm = sii8620_readb(ctx, REG_TRXSTA2); + + if ((tdm & MSK_TDM_SYNCHRONIZED) == VAL_TDM_SYNCHRONIZED) { + ctx->mode = CM_ECBUS_S; + ctx->burst.rx_ack = 0; + ctx->burst.r_size = SII8620_BURST_BUF_LEN; + sii8620_burst_tx_rbuf_info(ctx, SII8620_BURST_BUF_LEN); + sii8620_mt_read_devcap(ctx, true); + } else { + sii8620_write_seq_static(ctx, + REG_MHL_PLL_CTL2, 0, + REG_MHL_PLL_CTL2, BIT_MHL_PLL_CTL2_CLKDETECT_EN + ); + } + + sii8620_write(ctx, REG_TRXINTH, stat); +} + +static void sii8620_irq_block(struct sii8620 *ctx) +{ + u8 stat = sii8620_readb(ctx, REG_EMSCINTR); + + if (stat & BIT_EMSCINTR_SPI_DVLD) { + u8 bstat = sii8620_readb(ctx, REG_SPIBURSTSTAT); + + if (bstat & BIT_SPIBURSTSTAT_EMSC_NORMAL_MODE) + sii8620_burst_receive(ctx); + } + + sii8620_write(ctx, REG_EMSCINTR, stat); +} + /* endian agnostic, non-volatile version of test_bit */ static bool sii8620_test_bit(unsigned int nr, const u8 *addr) { @@ -1522,8 +1710,10 @@ static irqreturn_t sii8620_irq_thread(int irq, void *data) { BIT_FAST_INTR_STAT_DISC, sii8620_irq_disc }, { BIT_FAST_INTR_STAT_G2WB, sii8620_irq_g2wb }, { BIT_FAST_INTR_STAT_COC, sii8620_irq_coc }, + { BIT_FAST_INTR_STAT_TDM, sii8620_irq_tdm }, { BIT_FAST_INTR_STAT_MSC, sii8620_irq_msc }, { BIT_FAST_INTR_STAT_MERR, sii8620_irq_merr }, + { BIT_FAST_INTR_STAT_BLOCK, sii8620_irq_block }, { BIT_FAST_INTR_STAT_EDID, sii8620_irq_edid }, { BIT_FAST_INTR_STAT_SCDT, sii8620_irq_scdt }, { BIT_FAST_INTR_STAT_INFR, sii8620_irq_infr }, @@ -1539,7 +1729,9 @@ static irqreturn_t sii8620_irq_thread(int irq, void *data) if (sii8620_test_bit(irq_vec[i].bit, stats)) irq_vec[i].handler(ctx);
+ sii8620_burst_rx_all(ctx); sii8620_mt_work(ctx); + sii8620_burst_send(ctx);
ret = sii8620_clear_error(ctx); if (ret) { diff --git a/drivers/gpu/drm/bridge/sil-sii8620.h b/drivers/gpu/drm/bridge/sil-sii8620.h index 3ee4e7e..683213a 100644 --- a/drivers/gpu/drm/bridge/sil-sii8620.h +++ b/drivers/gpu/drm/bridge/sil-sii8620.h @@ -403,12 +403,16 @@
/* TDM RX Status 2nd, default value: 0x00 */ #define REG_TRXSTA2 0x015c +#define MSK_TDM_SYNCHRONIZED 0xc0 +#define VAL_TDM_SYNCHRONIZED 0x80
/* TDM RX INT Low, default value: 0x00 */ #define REG_TRXINTL 0x0163
/* TDM RX INT High, default value: 0x00 */ #define REG_TRXINTH 0x0164 +#define BIT_TDM_INTR_SYNC_DATA BIT(0) +#define BIT_TDM_INTR_SYNC_WAIT BIT(1)
/* TDM RX INTMASK High, default value: 0x00 */ #define REG_TRXINTMH 0x0166
MHL3 protocol requires device to respond to feature request from peer. This minimal answer fulfills the requirement and allows to continue negotiation.
Signed-off-by: Andrzej Hajda a.hajda@samsung.com --- drivers/gpu/drm/bridge/sil-sii8620.c | 4 ++++ 1 file changed, 4 insertions(+)
diff --git a/drivers/gpu/drm/bridge/sil-sii8620.c b/drivers/gpu/drm/bridge/sil-sii8620.c index 744e685..3842226 100644 --- a/drivers/gpu/drm/bridge/sil-sii8620.c +++ b/drivers/gpu/drm/bridge/sil-sii8620.c @@ -1475,6 +1475,10 @@ static void sii8620_msc_mr_set_int(struct sii8620 *ctx) break; } } + if (ints[MHL_INT_RCHANGE] & MHL_INT_RC_FEAT_REQ) { + sii8620_mt_set_int(ctx, MHL_INT_REG(RCHANGE), + MHL_INT_RC_FEAT_COMPLETE); + } }
static struct sii8620_mt_msg *sii8620_msc_msg_first(struct sii8620 *ctx)
Peer capabilities should be read differently depending on protocol version.
Signed-off-by: Andrzej Hajda a.hajda@samsung.com --- drivers/gpu/drm/bridge/sil-sii8620.c | 12 +++++++++++- 1 file changed, 11 insertions(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/bridge/sil-sii8620.c b/drivers/gpu/drm/bridge/sil-sii8620.c index 3842226..be953f3 100644 --- a/drivers/gpu/drm/bridge/sil-sii8620.c +++ b/drivers/gpu/drm/bridge/sil-sii8620.c @@ -1412,7 +1412,8 @@ static void sii8620_status_changed_path(struct sii8620 *ctx) sii8620_mt_write_stat(ctx, MHL_DST_REG(LINK_MODE), MHL_DST_LM_CLK_MODE_NORMAL | MHL_DST_LM_PATH_ENABLED); - sii8620_mt_read_devcap(ctx, false); + if (!sii8620_is_mhl3(ctx)) + sii8620_mt_read_devcap(ctx, false); } else { sii8620_mt_write_stat(ctx, MHL_DST_REG(LINK_MODE), MHL_DST_LM_CLK_MODE_NORMAL); @@ -1664,6 +1665,14 @@ static void sii8620_irq_infr(struct sii8620 *ctx) sii8620_start_video(ctx); }
+static void sii8620_got_xdevcap(struct sii8620 *ctx, int ret) +{ + if (ret < 0) + return; + + sii8620_mt_read_devcap(ctx, false); +} + static void sii8620_irq_tdm(struct sii8620 *ctx) { u8 stat = sii8620_readb(ctx, REG_TRXINTH); @@ -1675,6 +1684,7 @@ static void sii8620_irq_tdm(struct sii8620 *ctx) ctx->burst.r_size = SII8620_BURST_BUF_LEN; sii8620_burst_tx_rbuf_info(ctx, SII8620_BURST_BUF_LEN); sii8620_mt_read_devcap(ctx, true); + sii8620_mt_set_cont(ctx, sii8620_got_xdevcap); } else { sii8620_write_seq_static(ctx, REG_MHL_PLL_CTL2, 0,
In case of MHL3 CBUS is bring-up already in sii8620_got_ecbus_speed.
Signed-off-by: Andrzej Hajda a.hajda@samsung.com --- drivers/gpu/drm/bridge/sil-sii8620.c | 4 ---- 1 file changed, 4 deletions(-)
diff --git a/drivers/gpu/drm/bridge/sil-sii8620.c b/drivers/gpu/drm/bridge/sil-sii8620.c index be953f3..fb69353 100644 --- a/drivers/gpu/drm/bridge/sil-sii8620.c +++ b/drivers/gpu/drm/bridge/sil-sii8620.c @@ -453,10 +453,6 @@ static void sii8620_mr_xdevcap(struct sii8620 *ctx) { sii8620_read_buf(ctx, REG_EDID_FIFO_RD_DATA, ctx->xdevcap, MHL_XDC_SIZE); - - sii8620_mt_write_stat(ctx, MHL_XDS_REG(CURR_ECBUS_MODE), - MHL_XDS_ECBUS_S | MHL_XDS_SLOT_MODE_8BIT); - sii8620_mt_rap(ctx, MHL_RAP_CBUS_MODE_UP); }
static void sii8620_mt_read_devcap_recv(struct sii8620 *ctx,
Messages queue can be cleaned up by message callbacks, to avoid repeated removal of current message it should be removed from the queue before calling these callbacks.
Signed-off-by: Andrzej Hajda a.hajda@samsung.com --- drivers/gpu/drm/bridge/sil-sii8620.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/bridge/sil-sii8620.c b/drivers/gpu/drm/bridge/sil-sii8620.c index fb69353..a50ade6 100644 --- a/drivers/gpu/drm/bridge/sil-sii8620.c +++ b/drivers/gpu/drm/bridge/sil-sii8620.c @@ -272,11 +272,11 @@ static void sii8620_mt_work(struct sii8620 *ctx) ctx->mt_state = MT_STATE_READY; msg = list_first_entry(&ctx->mt_queue, struct sii8620_mt_msg, node); + list_del(&msg->node); if (msg->recv) msg->recv(ctx, msg); if (msg->continuation) msg->continuation(ctx, msg->ret); - list_del(&msg->node); kfree(msg); }
MHL2 receiver require disabling transmitter on initialization.
Signed-off-by: Andrzej Hajda a.hajda@samsung.com --- drivers/gpu/drm/bridge/sil-sii8620.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/bridge/sil-sii8620.c b/drivers/gpu/drm/bridge/sil-sii8620.c index a50ade6..7d28690 100644 --- a/drivers/gpu/drm/bridge/sil-sii8620.c +++ b/drivers/gpu/drm/bridge/sil-sii8620.c @@ -880,12 +880,11 @@ static void sii8620_stop_video(struct sii8620 *ctx) | BIT_TPI_SC_TPI_AV_MUTE; break; case SINK_HDMI: + default: val = BIT_TPI_SC_REG_TMDS_OE_POWER_DOWN | BIT_TPI_SC_TPI_AV_MUTE | BIT_TPI_SC_TPI_OUTPUT_MODE_0_HDMI; break; - default: - return; }
sii8620_write(ctx, REG_TPI_SC, val);
MHL1 and MHL3 have different initialization paths. To make both protocols happy sink detection is put into continuation after link mode enablement.
Signed-off-by: Andrzej Hajda a.hajda@samsung.com --- drivers/gpu/drm/bridge/sil-sii8620.c | 34 +++++++++++++++++++--------------- 1 file changed, 19 insertions(+), 15 deletions(-)
diff --git a/drivers/gpu/drm/bridge/sil-sii8620.c b/drivers/gpu/drm/bridge/sil-sii8620.c index 7d28690..5b879ff 100644 --- a/drivers/gpu/drm/bridge/sil-sii8620.c +++ b/drivers/gpu/drm/bridge/sil-sii8620.c @@ -402,7 +402,7 @@ static void sii8620_update_array(u8 *dst, u8 *src, int count) } }
-static void sii8620_mr_devcap(struct sii8620 *ctx) +static void sii8620_sink_detected(struct sii8620 *ctx, int ret) { static const char * const sink_str[] = { [SINK_NONE] = "NONE", @@ -410,23 +410,10 @@ static void sii8620_mr_devcap(struct sii8620 *ctx) [SINK_DVI] = "DVI" };
- u8 dcap[MHL_DCAP_SIZE]; char sink_name[20]; struct device *dev = ctx->dev;
- sii8620_read_buf(ctx, REG_EDID_FIFO_RD_DATA, dcap, MHL_DCAP_SIZE); - if (ctx->error < 0) - return; - - dev_info(dev, "dcap: %*ph\n", MHL_DCAP_SIZE, dcap); - dev_info(dev, "detected dongle MHL %d.%d, ChipID %02x%02x:%02x%02x\n", - dcap[MHL_DCAP_MHL_VERSION] / 16, - dcap[MHL_DCAP_MHL_VERSION] % 16, dcap[MHL_DCAP_ADOPTER_ID_H], - dcap[MHL_DCAP_ADOPTER_ID_L], dcap[MHL_DCAP_DEVICE_ID_H], - dcap[MHL_DCAP_DEVICE_ID_L]); - sii8620_update_array(ctx->devcap, dcap, MHL_DCAP_SIZE); - - if (!(dcap[MHL_DCAP_CAT] & MHL_DCAP_CAT_SINK)) + if (ret < 0) return;
sii8620_fetch_edid(ctx); @@ -449,6 +436,22 @@ static void sii8620_mr_devcap(struct sii8620 *ctx) sii8620_enable_hpd(ctx); }
+static void sii8620_mr_devcap(struct sii8620 *ctx) +{ + u8 dcap[MHL_DCAP_SIZE]; + struct device *dev = ctx->dev; + + sii8620_read_buf(ctx, REG_EDID_FIFO_RD_DATA, dcap, MHL_DCAP_SIZE); + if (ctx->error < 0) + return; + + dev_info(dev, "detected dongle MHL %d.%d, ChipID %02x%02x:%02x%02x\n", + dcap[MHL_DCAP_MHL_VERSION] / 16, dcap[MHL_DCAP_MHL_VERSION] % 16, + dcap[MHL_DCAP_ADOPTER_ID_H], dcap[MHL_DCAP_ADOPTER_ID_L], + dcap[MHL_DCAP_DEVICE_ID_H], dcap[MHL_DCAP_DEVICE_ID_L]); + sii8620_update_array(ctx->devcap, dcap, MHL_DCAP_SIZE); +} + static void sii8620_mr_xdevcap(struct sii8620 *ctx) { sii8620_read_buf(ctx, REG_EDID_FIFO_RD_DATA, ctx->xdevcap, @@ -1409,6 +1412,7 @@ static void sii8620_status_changed_path(struct sii8620 *ctx) | MHL_DST_LM_PATH_ENABLED); if (!sii8620_is_mhl3(ctx)) sii8620_mt_read_devcap(ctx, false); + sii8620_mt_set_cont(ctx, sii8620_sink_detected); } else { sii8620_mt_write_stat(ctx, MHL_DST_REG(LINK_MODE), MHL_DST_LM_CLK_MODE_NORMAL);
Write burst should be enabled for MHL_INT_RC_FEAT_REQ and disabled for other commands. The patch moves functions up and adds delay setting for MHL3 burst mode.
Signed-off-by: Andrzej Hajda a.hajda@samsung.com --- drivers/gpu/drm/bridge/sil-sii8620.c | 88 ++++++++++++++++++++---------------- 1 file changed, 50 insertions(+), 38 deletions(-)
diff --git a/drivers/gpu/drm/bridge/sil-sii8620.c b/drivers/gpu/drm/bridge/sil-sii8620.c index 5b879ff..653187c 100644 --- a/drivers/gpu/drm/bridge/sil-sii8620.c +++ b/drivers/gpu/drm/bridge/sil-sii8620.c @@ -289,9 +289,59 @@ static void sii8620_mt_work(struct sii8620 *ctx) msg->send(ctx, msg); }
+static void sii8620_enable_gen2_write_burst(struct sii8620 *ctx) +{ + u8 ctrl = BIT_MDT_RCV_CTRL_MDT_RCV_EN; + + if (ctx->gen2_write_burst) + return; + + if (ctx->mode >= CM_MHL1) + ctrl |= BIT_MDT_RCV_CTRL_MDT_DELAY_RCV_EN; + + sii8620_write_seq(ctx, + REG_MDT_RCV_TIMEOUT, 100, + REG_MDT_RCV_CTRL, ctrl + ); + ctx->gen2_write_burst = 1; +} + +static void sii8620_disable_gen2_write_burst(struct sii8620 *ctx) +{ + if (!ctx->gen2_write_burst) + return; + + sii8620_write_seq_static(ctx, + REG_MDT_XMIT_CTRL, 0, + REG_MDT_RCV_CTRL, 0 + ); + ctx->gen2_write_burst = 0; +} + +static void sii8620_start_gen2_write_burst(struct sii8620 *ctx) +{ + sii8620_write_seq_static(ctx, + REG_MDT_INT_1_MASK, BIT_MDT_RCV_TIMEOUT + | BIT_MDT_RCV_SM_ABORT_PKT_RCVD | BIT_MDT_RCV_SM_ERROR + | BIT_MDT_XMIT_TIMEOUT | BIT_MDT_XMIT_SM_ABORT_PKT_RCVD + | BIT_MDT_XMIT_SM_ERROR, + REG_MDT_INT_0_MASK, BIT_MDT_XFIFO_EMPTY + | BIT_MDT_IDLE_AFTER_HAWB_DISABLE + | BIT_MDT_RFIFO_DATA_RDY + ); + sii8620_enable_gen2_write_burst(ctx); +} + static void sii8620_mt_msc_cmd_send(struct sii8620 *ctx, struct sii8620_mt_msg *msg) { + if (msg->reg[0] == MHL_SET_INT && + msg->reg[1] == MHL_INT_REG(RCHANGE) && + msg->reg[2] == MHL_INT_RC_FEAT_REQ) + sii8620_enable_gen2_write_burst(ctx); + else + sii8620_disable_gen2_write_burst(ctx); + switch (msg->reg[0]) { case MHL_WRITE_STAT: case MHL_SET_INT: @@ -956,44 +1006,6 @@ static void sii8620_enable_hpd(struct sii8620 *ctx) ); }
-static void sii8620_enable_gen2_write_burst(struct sii8620 *ctx) -{ - if (ctx->gen2_write_burst) - return; - - sii8620_write_seq_static(ctx, - REG_MDT_RCV_TIMEOUT, 100, - REG_MDT_RCV_CTRL, BIT_MDT_RCV_CTRL_MDT_RCV_EN - ); - ctx->gen2_write_burst = 1; -} - -static void sii8620_disable_gen2_write_burst(struct sii8620 *ctx) -{ - if (!ctx->gen2_write_burst) - return; - - sii8620_write_seq_static(ctx, - REG_MDT_XMIT_CTRL, 0, - REG_MDT_RCV_CTRL, 0 - ); - ctx->gen2_write_burst = 0; -} - -static void sii8620_start_gen2_write_burst(struct sii8620 *ctx) -{ - sii8620_write_seq_static(ctx, - REG_MDT_INT_1_MASK, BIT_MDT_RCV_TIMEOUT - | BIT_MDT_RCV_SM_ABORT_PKT_RCVD | BIT_MDT_RCV_SM_ERROR - | BIT_MDT_XMIT_TIMEOUT | BIT_MDT_XMIT_SM_ABORT_PKT_RCVD - | BIT_MDT_XMIT_SM_ERROR, - REG_MDT_INT_0_MASK, BIT_MDT_XFIFO_EMPTY - | BIT_MDT_IDLE_AFTER_HAWB_DISABLE - | BIT_MDT_RFIFO_DATA_RDY - ); - sii8620_enable_gen2_write_burst(ctx); -} - static void sii8620_mhl_discover(struct sii8620 *ctx) { sii8620_write_seq_static(ctx,
Stopping output causes full re-detection of the sink and slows down the process.
Signed-off-by: Andrzej Hajda a.hajda@samsung.com --- drivers/gpu/drm/bridge/sil-sii8620.c | 13 ------------- 1 file changed, 13 deletions(-)
diff --git a/drivers/gpu/drm/bridge/sil-sii8620.c b/drivers/gpu/drm/bridge/sil-sii8620.c index 653187c..e84cda0 100644 --- a/drivers/gpu/drm/bridge/sil-sii8620.c +++ b/drivers/gpu/drm/bridge/sil-sii8620.c @@ -1614,17 +1614,6 @@ static void sii8620_scdt_high(struct sii8620 *ctx) ); }
-static void sii8620_scdt_low(struct sii8620 *ctx) -{ - sii8620_write(ctx, REG_TMDS_CSTAT_P3, - BIT_TMDS_CSTAT_P3_SCDT_CLR_AVI_DIS | - BIT_TMDS_CSTAT_P3_CLR_AVI); - - sii8620_stop_video(ctx); - - sii8620_write(ctx, REG_INTR8_MASK, 0); -} - static void sii8620_irq_scdt(struct sii8620 *ctx) { u8 stat = sii8620_readb(ctx, REG_INTR5); @@ -1634,8 +1623,6 @@ static void sii8620_irq_scdt(struct sii8620 *ctx)
if (cstat & BIT_TMDS_CSTAT_P3_SCDT) sii8620_scdt_high(ctx); - else - sii8620_scdt_low(ctx); }
sii8620_write(ctx, REG_INTR5, stat);
Without delay CBUS sometimes was not reset properly.
Signed-off-by: Andrzej Hajda a.hajda@samsung.com --- drivers/gpu/drm/bridge/sil-sii8620.c | 9 ++++----- 1 file changed, 4 insertions(+), 5 deletions(-)
diff --git a/drivers/gpu/drm/bridge/sil-sii8620.c b/drivers/gpu/drm/bridge/sil-sii8620.c index e84cda0..6ef1a4d 100644 --- a/drivers/gpu/drm/bridge/sil-sii8620.c +++ b/drivers/gpu/drm/bridge/sil-sii8620.c @@ -891,11 +891,10 @@ static void sii8620_hw_reset(struct sii8620 *ctx)
static void sii8620_cbus_reset(struct sii8620 *ctx) { - sii8620_write_seq_static(ctx, - REG_PWD_SRST, BIT_PWD_SRST_CBUS_RST - | BIT_PWD_SRST_CBUS_RST_SW_EN, - REG_PWD_SRST, BIT_PWD_SRST_CBUS_RST_SW_EN - ); + sii8620_write(ctx, REG_PWD_SRST, BIT_PWD_SRST_CBUS_RST + | BIT_PWD_SRST_CBUS_RST_SW_EN); + usleep_range(10000, 20000); + sii8620_write(ctx, REG_PWD_SRST, BIT_PWD_SRST_CBUS_RST_SW_EN); }
static void sii8620_set_auto_zone(struct sii8620 *ctx)
MHL3 requires that after reading EDID from the sink source should ask peer for features. To make both protocols happy the patch splits the code accordingly.
Signed-off-by: Andrzej Hajda a.hajda@samsung.com --- drivers/gpu/drm/bridge/sil-sii8620.c | 31 +++++++++++++++++++++++++++---- 1 file changed, 27 insertions(+), 4 deletions(-)
diff --git a/drivers/gpu/drm/bridge/sil-sii8620.c b/drivers/gpu/drm/bridge/sil-sii8620.c index 6ef1a4d..d0e6dc3 100644 --- a/drivers/gpu/drm/bridge/sil-sii8620.c +++ b/drivers/gpu/drm/bridge/sil-sii8620.c @@ -482,6 +482,13 @@ static void sii8620_sink_detected(struct sii8620 *ctx, int ret)
dev_info(dev, "detected sink(type: %s): %s\n", sink_str[ctx->sink_type], sink_name); +} + +static void sii8620_edid_read(struct sii8620 *ctx, int ret) +{ + if (ret < 0) + return; + sii8620_set_upstream_edid(ctx); sii8620_enable_hpd(ctx); } @@ -787,12 +794,12 @@ static void sii8620_fetch_edid(struct sii8620 *ctx) edid = new_edid; } } - - if (fetched + FETCH_SIZE == edid_len) - sii8620_write(ctx, REG_INTR3, int3); }
- sii8620_write(ctx, REG_LM_DDC, lm_ddc); + sii8620_write_seq(ctx, + REG_INTR3_MASK, BIT_DDC_CMD_DONE, + REG_LM_DDC, lm_ddc + );
end: kfree(ctx->edid); @@ -1706,6 +1713,21 @@ static void sii8620_irq_block(struct sii8620 *ctx) sii8620_write(ctx, REG_EMSCINTR, stat); }
+static void sii8620_irq_ddc(struct sii8620 *ctx) +{ + u8 stat = sii8620_readb(ctx, REG_INTR3); + + if (stat & BIT_DDC_CMD_DONE) { + sii8620_write(ctx, REG_INTR3_MASK, 0); + if (sii8620_is_mhl3(ctx)) + sii8620_mt_set_int(ctx, MHL_INT_REG(RCHANGE), + MHL_INT_RC_FEAT_REQ); + else + sii8620_edid_read(ctx, 0); + } + sii8620_write(ctx, REG_INTR3, stat); +} + /* endian agnostic, non-volatile version of test_bit */ static bool sii8620_test_bit(unsigned int nr, const u8 *addr) { @@ -1726,6 +1748,7 @@ static irqreturn_t sii8620_irq_thread(int irq, void *data) { BIT_FAST_INTR_STAT_MERR, sii8620_irq_merr }, { BIT_FAST_INTR_STAT_BLOCK, sii8620_irq_block }, { BIT_FAST_INTR_STAT_EDID, sii8620_irq_edid }, + { BIT_FAST_INTR_STAT_DDC, sii8620_irq_ddc }, { BIT_FAST_INTR_STAT_SCDT, sii8620_irq_scdt }, { BIT_FAST_INTR_STAT_INFR, sii8620_irq_infr }, };
The patch allows to avoid rare cases when discovery fails.
Signed-off-by: Andrzej Hajda a.hajda@samsung.com --- drivers/gpu/drm/bridge/sil-sii8620.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/bridge/sil-sii8620.c b/drivers/gpu/drm/bridge/sil-sii8620.c index d0e6dc3..1c76905 100644 --- a/drivers/gpu/drm/bridge/sil-sii8620.c +++ b/drivers/gpu/drm/bridge/sil-sii8620.c @@ -1286,10 +1286,12 @@ static void sii8620_disconnect(struct sii8620 *ctx) { sii8620_disable_gen2_write_burst(ctx); sii8620_stop_video(ctx); - msleep(50); + msleep(100); sii8620_cbus_reset(ctx); sii8620_set_mode(ctx, CM_DISCONNECTED); sii8620_write_seq_static(ctx, + REG_TX_ZONE_CTL1, 0, + REG_MHL_PLL_CTL0, 0x07, REG_COC_CTL0, 0x40, REG_CBUS3_CNVT, 0x84, REG_COC_CTL14, 0x00,
MHL3 protocol uses vendor specific infoframes to transmit additional information to the sink. This patch adds definitions of structures and constants used to create such frames.
Signed-off-by: Andrzej Hajda a.hajda@samsung.com --- include/drm/bridge/mhl.h | 32 ++++++++++++++++++++++++++++++++ 1 file changed, 32 insertions(+)
diff --git a/include/drm/bridge/mhl.h b/include/drm/bridge/mhl.h index e8d194d..fbdfc8d 100644 --- a/include/drm/bridge/mhl.h +++ b/include/drm/bridge/mhl.h @@ -341,4 +341,36 @@ struct mhl_burst_audio_descr { u8 short_desc[9]; } __packed;
+/* + * MHL3 infoframe related definitions + */ + +#define MHL3_IEEE_OUI 0x7ca61d +#define MHL3_INFOFRAME_SIZE 15 + +enum mhl3_video_format { + MHL3_VIDEO_FORMAT_NONE, + MHL3_VIDEO_FORMAT_3D, + MHL3_VIDEO_FORMAT_MULTI_VIEW, + MHL3_VIDEO_FORMAT_DUAL_3D +}; + +enum mhl3_3d_format_type { + MHL3_3D_FORMAT_TYPE_FS, /* frame sequential */ + MHL3_3D_FORMAT_TYPE_TB, /* top-bottom */ + MHL3_3D_FORMAT_TYPE_LR, /* left-right */ + MHL3_3D_FORMAT_TYPE_FS_TB, /* frame sequential, top-bottom */ + MHL3_3D_FORMAT_TYPE_FS_LR, /* frame sequential, left-right */ + MHL3_3D_FORMAT_TYPE_TB_LR /* top-bottom, left-right */ +}; + +struct mhl3_infoframe { + unsigned char version; + enum mhl3_video_format video_format; + enum mhl3_3d_format_type format_type; + bool sep_audio; + int hev_format; + int av_delay; +}; + #endif /* __MHL_H__ */
MHL3 protocol requires registry adjustments depending on chosen video mode. Necessary information is gathered in mode_fixup callback. In case of HDMI video modes driver should also send special AVI and MHL3 infoframes. The patch introduces generic helpers for handling MHL3 infoframes, in case of appearance of other users of MHL3 infoframes these function can be moved to common library.
Signed-off-by: Andrzej Hajda a.hajda@samsung.com --- drivers/gpu/drm/bridge/sil-sii8620.c | 280 +++++++++++++++++++++++++++++++---- drivers/gpu/drm/bridge/sil-sii8620.h | 15 +- 2 files changed, 262 insertions(+), 33 deletions(-)
diff --git a/drivers/gpu/drm/bridge/sil-sii8620.c b/drivers/gpu/drm/bridge/sil-sii8620.c index 1c76905..243af5f 100644 --- a/drivers/gpu/drm/bridge/sil-sii8620.c +++ b/drivers/gpu/drm/bridge/sil-sii8620.c @@ -32,6 +32,8 @@
#define SII8620_BURST_BUF_LEN 288 #define VAL_RX_HDMI_CTRL2_DEFVAL VAL_RX_HDMI_CTRL2_IDLE_CNT(3) +#define MHL1_MAX_LCLK 225000 +#define MHL3_MAX_LCLK 600000
enum sii8620_mode { CM_DISCONNECTED, @@ -62,6 +64,9 @@ struct sii8620 { struct regulator_bulk_data supplies[2]; struct mutex lock; /* context lock, protects fields below */ int error; + int pixel_clock; + unsigned int use_packed_pixel:1; + int video_code; enum sii8620_mode mode; enum sii8620_sink_type sink_type; u8 cbus_status; @@ -69,7 +74,7 @@ struct sii8620 { u8 xstat[MHL_XDS_SIZE]; u8 devcap[MHL_DCAP_SIZE]; u8 xdevcap[MHL_XDC_SIZE]; - u8 avif[19]; + u8 avif[HDMI_INFOFRAME_SIZE(AVI)]; struct edid *edid; unsigned int gen2_write_burst:1; enum sii8620_mt_state mt_state; @@ -685,6 +690,40 @@ static void sii8620_burst_tx_rbuf_info(struct sii8620 *ctx, int size) d->size = cpu_to_le16(size); }
+static u8 sii8620_checksum(void *ptr, int size) +{ + u8 *d = ptr, sum = 0; + + while (size--) + sum += *d++; + + return sum; +} + +static void sii8620_mhl_burst_hdr_set(struct mhl3_burst_header *h, + enum mhl_burst_id id) +{ + h->id = cpu_to_be16(id); + h->total_entries = 1; + h->sequence_index = 1; +} + +static void sii8620_burst_tx_bits_per_pixel_fmt(struct sii8620 *ctx, u8 fmt) +{ + struct mhl_burst_bits_per_pixel_fmt *d; + const int size = sizeof(*d) + sizeof(d->desc[0]); + + d = sii8620_burst_get_tx_buf(ctx, size); + if (!d) + return; + + sii8620_mhl_burst_hdr_set(&d->hdr, MHL_BURST_ID_BITS_PER_PIXEL_FMT); + d->num_entries = 1; + d->desc[0].stream_id = 0; + d->desc[0].pixel_format = fmt; + d->hdr.checksum -= sii8620_checksum(d, size); +} + static void sii8620_burst_rx_all(struct sii8620 *ctx) { u8 *d = ctx->burst.rx_buf; @@ -949,32 +988,193 @@ static void sii8620_stop_video(struct sii8620 *ctx) sii8620_write(ctx, REG_TPI_SC, val); }
+static void sii8620_set_format(struct sii8620 *ctx) +{ + u8 out_fmt; + + if (sii8620_is_mhl3(ctx)) { + sii8620_setbits(ctx, REG_M3_P0CTRL, + BIT_M3_P0CTRL_MHL3_P0_PIXEL_MODE_PACKED, + ctx->use_packed_pixel ? ~0 : 0); + } else { + if (ctx->use_packed_pixel) + sii8620_write_seq_static(ctx, + REG_VID_MODE, BIT_VID_MODE_M1080P, + REG_MHL_TOP_CTL, BIT_MHL_TOP_CTL_MHL_PP_SEL | 1, + REG_MHLTX_CTL6, 0x60 + ); + else + sii8620_write_seq_static(ctx, + REG_VID_MODE, 0, + REG_MHL_TOP_CTL, 1, + REG_MHLTX_CTL6, 0xa0 + ); + } + + if (ctx->use_packed_pixel) + out_fmt = VAL_TPI_FORMAT(YCBCR422, FULL) | + BIT_TPI_OUTPUT_CSCMODE709; + else + out_fmt = VAL_TPI_FORMAT(RGB, FULL); + + sii8620_write_seq(ctx, + REG_TPI_INPUT, VAL_TPI_FORMAT(RGB, FULL), + REG_TPI_OUTPUT, out_fmt, + ); +} + +static int mhl3_infoframe_init(struct mhl3_infoframe *frame) +{ + memset(frame, 0, sizeof(*frame)); + + frame->version = 3; + frame->hev_format = -1; + return 0; +} + +static ssize_t mhl3_infoframe_pack(struct mhl3_infoframe *frame, + void *buffer, size_t size) +{ + const int frm_len = HDMI_INFOFRAME_HEADER_SIZE + MHL3_INFOFRAME_SIZE; + u8 *ptr = buffer; + + if (size < frm_len) + return -ENOSPC; + + memset(buffer, 0, size); + ptr[0] = HDMI_INFOFRAME_TYPE_VENDOR; + ptr[1] = frame->version; + ptr[2] = MHL3_INFOFRAME_SIZE; + ptr[4] = MHL3_IEEE_OUI & 0xff; + ptr[5] = (MHL3_IEEE_OUI >> 8) & 0xff; + ptr[6] = (MHL3_IEEE_OUI >> 16) & 0xff; + ptr[7] = frame->video_format & 0x3; + ptr[7] |= (frame->format_type & 0x7) << 2; + ptr[7] |= frame->sep_audio ? BIT(5) : 0; + if (frame->hev_format >= 0) { + ptr[9] = 1; + ptr[10] = (frame->hev_format >> 8) & 0xff; + ptr[11] = frame->hev_format & 0xff; + } + if (frame->av_delay) { + bool sign = frame->av_delay < 0; + int delay = sign ? -frame->av_delay : frame->av_delay; + + ptr[12] = (delay >> 16) & 0xf; + if (sign) + ptr[12] |= BIT(4); + ptr[13] = (delay >> 8) & 0xff; + ptr[14] = delay & 0xff; + } + ptr[3] -= sii8620_checksum(buffer, frm_len); + return frm_len; +} + +static void sii8620_set_infoframes(struct sii8620 *ctx) +{ + struct mhl3_infoframe mhl_frm; + union hdmi_infoframe frm; + u8 buf[31]; + int ret; + + if (!sii8620_is_mhl3(ctx) || !ctx->use_packed_pixel) { + sii8620_write(ctx, REG_TPI_SC, + BIT_TPI_SC_TPI_OUTPUT_MODE_0_HDMI); + sii8620_write_buf(ctx, REG_TPI_AVI_CHSUM, ctx->avif + 3, + ARRAY_SIZE(ctx->avif) - 3); + sii8620_write(ctx, REG_PKT_FILTER_0, + BIT_PKT_FILTER_0_DROP_CEA_GAMUT_PKT | + BIT_PKT_FILTER_0_DROP_MPEG_PKT | + BIT_PKT_FILTER_0_DROP_GCP_PKT, + BIT_PKT_FILTER_1_DROP_GEN_PKT); + return; + } + + ret = hdmi_avi_infoframe_init(&frm.avi); + frm.avi.colorspace = HDMI_COLORSPACE_YUV422; + frm.avi.active_aspect = HDMI_ACTIVE_ASPECT_PICTURE; + frm.avi.picture_aspect = HDMI_PICTURE_ASPECT_16_9; + frm.avi.colorimetry = HDMI_COLORIMETRY_ITU_709; + frm.avi.video_code = ctx->video_code; + if (!ret) + ret = hdmi_avi_infoframe_pack(&frm.avi, buf, ARRAY_SIZE(buf)); + if (ret > 0) + sii8620_write_buf(ctx, REG_TPI_AVI_CHSUM, buf + 3, ret - 3); + sii8620_write(ctx, REG_PKT_FILTER_0, + BIT_PKT_FILTER_0_DROP_CEA_GAMUT_PKT | + BIT_PKT_FILTER_0_DROP_MPEG_PKT | + BIT_PKT_FILTER_0_DROP_AVI_PKT | + BIT_PKT_FILTER_0_DROP_GCP_PKT, + BIT_PKT_FILTER_1_VSI_OVERRIDE_DIS | + BIT_PKT_FILTER_1_DROP_GEN_PKT | + BIT_PKT_FILTER_1_DROP_VSIF_PKT); + + sii8620_write(ctx, REG_TPI_INFO_FSEL, BIT_TPI_INFO_FSEL_EN + | BIT_TPI_INFO_FSEL_RPT | VAL_TPI_INFO_FSEL_VSI); + ret = mhl3_infoframe_init(&mhl_frm); + if (!ret) + ret = mhl3_infoframe_pack(&mhl_frm, buf, ARRAY_SIZE(buf)); + sii8620_write_buf(ctx, REG_TPI_INFO_B0, buf, ret); +} + static void sii8620_start_hdmi(struct sii8620 *ctx) { sii8620_write_seq_static(ctx, REG_RX_HDMI_CTRL2, VAL_RX_HDMI_CTRL2_DEFVAL | BIT_RX_HDMI_CTRL2_USE_AV_MUTE, REG_VID_OVRRD, BIT_VID_OVRRD_PP_AUTO_DISABLE - | BIT_VID_OVRRD_M1080P_OVRRD, - REG_VID_MODE, 0, - REG_MHL_TOP_CTL, 0x1, - REG_MHLTX_CTL6, 0xa0, - REG_TPI_INPUT, VAL_TPI_FORMAT(RGB, FULL), - REG_TPI_OUTPUT, VAL_TPI_FORMAT(RGB, FULL), - ); - - sii8620_mt_write_stat(ctx, MHL_DST_REG(LINK_MODE), - MHL_DST_LM_CLK_MODE_NORMAL | - MHL_DST_LM_PATH_ENABLED); + | BIT_VID_OVRRD_M1080P_OVRRD); + sii8620_set_format(ctx);
- sii8620_set_auto_zone(ctx); + if (!sii8620_is_mhl3(ctx)) { + sii8620_mt_write_stat(ctx, MHL_DST_REG(LINK_MODE), + MHL_DST_LM_CLK_MODE_NORMAL | MHL_DST_LM_PATH_ENABLED); + sii8620_set_auto_zone(ctx); + } else { + static const struct { + int max_clk; + u8 zone; + u8 link_rate; + u8 rrp_decode; + } clk_spec[] = { + { 150000, VAL_TX_ZONE_CTL3_TX_ZONE_1_5GBPS, + MHL_XDS_LINK_RATE_1_5_GBPS, 0x38 }, + { 300000, VAL_TX_ZONE_CTL3_TX_ZONE_3GBPS, + MHL_XDS_LINK_RATE_3_0_GBPS, 0x40 }, + { 600000, VAL_TX_ZONE_CTL3_TX_ZONE_6GBPS, + MHL_XDS_LINK_RATE_6_0_GBPS, 0x40 }, + }; + u8 p0_ctrl = BIT_M3_P0CTRL_MHL3_P0_PORT_EN; + int clk = ctx->pixel_clock * (ctx->use_packed_pixel ? 2 : 3); + int i; + + for (i = 0; i < ARRAY_SIZE(clk_spec); ++i) + if (clk < clk_spec[i].max_clk) + break;
- sii8620_write(ctx, REG_TPI_SC, BIT_TPI_SC_TPI_OUTPUT_MODE_0_HDMI); + if (100 * clk >= 98 * clk_spec[i].max_clk) + p0_ctrl |= BIT_M3_P0CTRL_MHL3_P0_UNLIMIT_EN;
- sii8620_write_buf(ctx, REG_TPI_AVI_CHSUM, ctx->avif, - ARRAY_SIZE(ctx->avif)); + sii8620_burst_tx_bits_per_pixel_fmt(ctx, ctx->use_packed_pixel); + sii8620_burst_send(ctx); + sii8620_write_seq(ctx, + REG_MHL_DP_CTL0, 0xf0, + REG_MHL3_TX_ZONE_CTL, clk_spec[i].zone); + sii8620_setbits(ctx, REG_M3_P0CTRL, + BIT_M3_P0CTRL_MHL3_P0_PORT_EN + | BIT_M3_P0CTRL_MHL3_P0_UNLIMIT_EN, p0_ctrl); + sii8620_setbits(ctx, REG_M3_POSTM, MSK_M3_POSTM_RRP_DECODE, + clk_spec[i].rrp_decode); + sii8620_write_seq_static(ctx, + REG_M3_CTRL, VAL_M3_CTRL_MHL3_VALUE + | BIT_M3_CTRL_H2M_SWRST, + REG_M3_CTRL, VAL_M3_CTRL_MHL3_VALUE + ); + sii8620_mt_write_stat(ctx, MHL_XDS_REG(AVLINK_MODE_CONTROL), + clk_spec[i].link_rate); + }
- sii8620_write(ctx, REG_PKT_FILTER_0, 0xa1, 0x2); + sii8620_set_infoframes(ctx); }
static void sii8620_start_video(struct sii8620 *ctx) @@ -1834,22 +2034,44 @@ static bool sii8620_mode_fixup(struct drm_bridge *bridge, struct drm_display_mode *adjusted_mode) { struct sii8620 *ctx = bridge_to_sii8620(bridge); - bool ret = false; - int max_clock = 74250; - - mutex_lock(&ctx->lock); - - if (mode->flags & DRM_MODE_FLAG_INTERLACE) - goto out; + int max_lclk; + bool ret = true;
- if (ctx->devcap[MHL_DCAP_VID_LINK_MODE] & MHL_DCAP_VID_LINK_PPIXEL) - max_clock = 300000; + if (adjusted_mode->flags & DRM_MODE_FLAG_INTERLACE) + return false;
- ret = mode->clock <= max_clock; + mutex_lock(&ctx->lock);
-out: + max_lclk = sii8620_is_mhl3(ctx) ? MHL3_MAX_LCLK : MHL1_MAX_LCLK; + if (max_lclk > 3 * adjusted_mode->clock) { + ctx->use_packed_pixel = 0; + goto end; + } + if ((ctx->devcap[MHL_DCAP_VID_LINK_MODE] & MHL_DCAP_VID_LINK_PPIXEL) && + max_lclk > 2 * adjusted_mode->clock) { + ctx->use_packed_pixel = 1; + goto end; + } + ret = false; +end: + if (ret) { + u8 vic = drm_match_cea_mode(adjusted_mode); + + if (!vic) { + union hdmi_infoframe frm; + u8 mhl_vic[] = { 0, 95, 94, 93, 98 }; + + drm_hdmi_vendor_infoframe_from_display_mode( + &frm.vendor.hdmi, adjusted_mode); + vic = frm.vendor.hdmi.vic; + if (vic >= ARRAY_SIZE(mhl_vic)) + vic = 0; + vic = mhl_vic[vic]; + } + ctx->video_code = vic; + ctx->pixel_clock = adjusted_mode->clock; + } mutex_unlock(&ctx->lock); - return ret; }
diff --git a/drivers/gpu/drm/bridge/sil-sii8620.h b/drivers/gpu/drm/bridge/sil-sii8620.h index 683213a..613943a 100644 --- a/drivers/gpu/drm/bridge/sil-sii8620.h +++ b/drivers/gpu/drm/bridge/sil-sii8620.h @@ -1084,10 +1084,17 @@
/* TPI Info Frame Select, default value: 0x00 */ #define REG_TPI_INFO_FSEL 0x06bf -#define BIT_TPI_INFO_FSEL_TPI_INFO_EN BIT(7) -#define BIT_TPI_INFO_FSEL_TPI_INFO_RPT BIT(6) -#define BIT_TPI_INFO_FSEL_TPI_INFO_READ_FLAG BIT(5) -#define MSK_TPI_INFO_FSEL_TPI_INFO_SEL 0x07 +#define BIT_TPI_INFO_FSEL_EN BIT(7) +#define BIT_TPI_INFO_FSEL_RPT BIT(6) +#define BIT_TPI_INFO_FSEL_READ_FLAG BIT(5) +#define MSK_TPI_INFO_FSEL_PKT 0x07 +#define VAL_TPI_INFO_FSEL_AVI 0x00 +#define VAL_TPI_INFO_FSEL_SPD 0x01 +#define VAL_TPI_INFO_FSEL_AUD 0x02 +#define VAL_TPI_INFO_FSEL_MPG 0x03 +#define VAL_TPI_INFO_FSEL_GEN 0x04 +#define VAL_TPI_INFO_FSEL_GEN2 0x05 +#define VAL_TPI_INFO_FSEL_VSI 0x06
/* TPI Info Byte #0, default value: 0x00 */ #define REG_TPI_INFO_B0 0x06c0
Device should report to the peer which features are really supported.
Signed-off-by: Andrzej Hajda a.hajda@samsung.com --- drivers/gpu/drm/bridge/sil-sii8620.c | 27 +++++++++++++++++++++++---- drivers/gpu/drm/bridge/sil-sii8620.h | 16 ++++++++-------- 2 files changed, 31 insertions(+), 12 deletions(-)
diff --git a/drivers/gpu/drm/bridge/sil-sii8620.c b/drivers/gpu/drm/bridge/sil-sii8620.c index 243af5f..66ad397 100644 --- a/drivers/gpu/drm/bridge/sil-sii8620.c +++ b/drivers/gpu/drm/bridge/sil-sii8620.c @@ -1675,6 +1675,25 @@ static void sii8620_got_ecbus_speed(struct sii8620 *ctx, int ret) sii8620_mt_set_cont(ctx, sii8620_ecbus_up); }
+static void sii8620_mhl_burst_emsc_support_set(struct mhl_burst_emsc_support *d, + enum mhl_burst_id id) +{ + sii8620_mhl_burst_hdr_set(&d->hdr, MHL_BURST_ID_EMSC_SUPPORT); + d->num_entries = 1; + d->burst_id[0] = cpu_to_be16(id); +} + +static void sii8620_send_features(struct sii8620 *ctx) +{ + u8 buf[16]; + + sii8620_write(ctx, REG_MDT_XMIT_CTRL, BIT_MDT_XMIT_CTRL_EN + | BIT_MDT_XMIT_CTRL_FIXED_BURST_LEN); + sii8620_mhl_burst_emsc_support_set((void *)buf, + MHL_BURST_ID_HID_PAYLOAD); + sii8620_write_buf(ctx, REG_MDT_XMIT_WRITE_PORT, buf, ARRAY_SIZE(buf)); +} + static void sii8620_msc_mr_set_int(struct sii8620 *ctx) { u8 ints[MHL_INT_SIZE]; @@ -1695,10 +1714,10 @@ static void sii8620_msc_mr_set_int(struct sii8620 *ctx) break; } } - if (ints[MHL_INT_RCHANGE] & MHL_INT_RC_FEAT_REQ) { - sii8620_mt_set_int(ctx, MHL_INT_REG(RCHANGE), - MHL_INT_RC_FEAT_COMPLETE); - } + if (ints[MHL_INT_RCHANGE] & MHL_INT_RC_FEAT_REQ) + sii8620_send_features(ctx); + if (ints[MHL_INT_RCHANGE] & MHL_INT_RC_FEAT_COMPLETE) + sii8620_edid_read(ctx, 0); }
static struct sii8620_mt_msg *sii8620_msc_msg_first(struct sii8620 *ctx) diff --git a/drivers/gpu/drm/bridge/sil-sii8620.h b/drivers/gpu/drm/bridge/sil-sii8620.h index 613943a..c5a7c18 100644 --- a/drivers/gpu/drm/bridge/sil-sii8620.h +++ b/drivers/gpu/drm/bridge/sil-sii8620.h @@ -1298,14 +1298,14 @@
/* MDT Transmit Control, default value: 0x70 */ #define REG_MDT_XMIT_CTRL 0x0588 -#define BIT_MDT_XMIT_CTRL_MDT_XMIT_EN BIT(7) -#define BIT_MDT_XMIT_CTRL_MDT_XMIT_CMD_MERGE_EN BIT(6) -#define BIT_MDT_XMIT_CTRL_MDT_XMIT_FIXED_BURST_LEN BIT(5) -#define BIT_MDT_XMIT_CTRL_MDT_XMIT_FIXED_AID BIT(4) -#define BIT_MDT_XMIT_CTRL_MDT_XMIT_SINGLE_RUN_EN BIT(3) -#define BIT_MDT_XMIT_CTRL_MDT_CLR_ABORT_WAIT BIT(2) -#define BIT_MDT_XMIT_CTRL_MDT_XFIFO_CLR_ALL BIT(1) -#define BIT_MDT_XMIT_CTRL_MDT_XFIFO_CLR_CUR BIT(0) +#define BIT_MDT_XMIT_CTRL_EN BIT(7) +#define BIT_MDT_XMIT_CTRL_CMD_MERGE_EN BIT(6) +#define BIT_MDT_XMIT_CTRL_FIXED_BURST_LEN BIT(5) +#define BIT_MDT_XMIT_CTRL_FIXED_AID BIT(4) +#define BIT_MDT_XMIT_CTRL_SINGLE_RUN_EN BIT(3) +#define BIT_MDT_XMIT_CTRL_CLR_ABORT_WAIT BIT(2) +#define BIT_MDT_XMIT_CTRL_XFIFO_CLR_ALL BIT(1) +#define BIT_MDT_XMIT_CTRL_XFIFO_CLR_CUR BIT(0)
/* MDT Receive WRITE Port, default value: 0x00 */ #define REG_MDT_XMIT_WRITE_PORT 0x0589
The patch adds code to report back feature complete IRQ, and code to read and drop burst writes from peer.
Signed-off-by: Andrzej Hajda a.hajda@samsung.com --- drivers/gpu/drm/bridge/sil-sii8620.c | 21 ++++++++++++++++++++- 1 file changed, 20 insertions(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/bridge/sil-sii8620.c b/drivers/gpu/drm/bridge/sil-sii8620.c index 66ad397..54ea864 100644 --- a/drivers/gpu/drm/bridge/sil-sii8620.c +++ b/drivers/gpu/drm/bridge/sil-sii8620.c @@ -1604,12 +1604,31 @@ static void sii8620_irq_disc(struct sii8620 *ctx) sii8620_write(ctx, REG_CBUS_DISC_INTR0, stat); }
+static void sii8620_read_burst(struct sii8620 *ctx) +{ + u8 buf[17]; + + sii8620_read_buf(ctx, REG_MDT_RCV_READ_PORT, buf, ARRAY_SIZE(buf)); + sii8620_write(ctx, REG_MDT_RCV_CTRL, BIT_MDT_RCV_CTRL_MDT_RCV_EN | + BIT_MDT_RCV_CTRL_MDT_DELAY_RCV_EN | + BIT_MDT_RCV_CTRL_MDT_RFIFO_CLR_CUR); + sii8620_readb(ctx, REG_MDT_RFIFO_STAT); +} + static void sii8620_irq_g2wb(struct sii8620 *ctx) { u8 stat = sii8620_readb(ctx, REG_MDT_INT_0);
if (stat & BIT_MDT_IDLE_AFTER_HAWB_DISABLE) - dev_dbg(ctx->dev, "HAWB idle\n"); + if (sii8620_is_mhl3(ctx)) + sii8620_mt_set_int(ctx, MHL_INT_REG(RCHANGE), + MHL_INT_RC_FEAT_COMPLETE); + + if (stat & BIT_MDT_RFIFO_DATA_RDY) + sii8620_read_burst(ctx); + + if (stat & BIT_MDT_XFIFO_EMPTY) + sii8620_write(ctx, REG_MDT_XMIT_CTRL, 0);
sii8620_write(ctx, REG_MDT_INT_0, stat); }
In case of MHL3 HSIC should be initialized.
Signed-off-by: Andrzej Hajda a.hajda@samsung.com --- drivers/gpu/drm/bridge/sil-sii8620.c | 38 ++++++++++++++++++++++++++++++++++++ drivers/gpu/drm/bridge/sil-sii8620.h | 10 ++++++---- 2 files changed, 44 insertions(+), 4 deletions(-)
diff --git a/drivers/gpu/drm/bridge/sil-sii8620.c b/drivers/gpu/drm/bridge/sil-sii8620.c index 54ea864..be7be3c 100644 --- a/drivers/gpu/drm/bridge/sil-sii8620.c +++ b/drivers/gpu/drm/bridge/sil-sii8620.c @@ -489,12 +489,50 @@ static void sii8620_sink_detected(struct sii8620 *ctx, int ret) sink_str[ctx->sink_type], sink_name); }
+static void sii8620_hsic_init(struct sii8620 *ctx) +{ + if (!sii8620_is_mhl3(ctx)) + return; + + sii8620_write(ctx, REG_FCGC, + BIT_FCGC_HSIC_HOSTMODE | BIT_FCGC_HSIC_ENABLE); + sii8620_setbits(ctx, REG_HRXCTRL3, + BIT_HRXCTRL3_HRX_STAY_RESET | BIT_HRXCTRL3_STATUS_EN, ~0); + sii8620_setbits(ctx, REG_TTXNUMB, MSK_TTXNUMB_TTX_NUMBPS, 4); + sii8620_setbits(ctx, REG_TRXCTRL, BIT_TRXCTRL_TRX_FROM_SE_COC, ~0); + sii8620_setbits(ctx, REG_HTXCTRL, BIT_HTXCTRL_HTX_DRVCONN1, 0); + sii8620_setbits(ctx, REG_KEEPER, MSK_KEEPER_MODE, VAL_KEEPER_MODE_HOST); + sii8620_write_seq_static(ctx, + REG_TDMLLCTL, 0, + REG_UTSRST, BIT_UTSRST_HRX_SRST | BIT_UTSRST_HTX_SRST | + BIT_UTSRST_KEEPER_SRST | BIT_UTSRST_FC_SRST, + REG_UTSRST, BIT_UTSRST_HRX_SRST | BIT_UTSRST_HTX_SRST, + REG_HRXINTL, 0xff, + REG_HRXINTH, 0xff, + REG_TTXINTL, 0xff, + REG_TTXINTH, 0xff, + REG_TRXINTL, 0xff, + REG_TRXINTH, 0xff, + REG_HTXINTL, 0xff, + REG_HTXINTH, 0xff, + REG_FCINTR0, 0xff, + REG_FCINTR1, 0xff, + REG_FCINTR2, 0xff, + REG_FCINTR3, 0xff, + REG_FCINTR4, 0xff, + REG_FCINTR5, 0xff, + REG_FCINTR6, 0xff, + REG_FCINTR7, 0xff + ); +} + static void sii8620_edid_read(struct sii8620 *ctx, int ret) { if (ret < 0) return;
sii8620_set_upstream_edid(ctx); + sii8620_hsic_init(ctx); sii8620_enable_hpd(ctx); }
diff --git a/drivers/gpu/drm/bridge/sil-sii8620.h b/drivers/gpu/drm/bridge/sil-sii8620.h index c5a7c18..038d33e 100644 --- a/drivers/gpu/drm/bridge/sil-sii8620.h +++ b/drivers/gpu/drm/bridge/sil-sii8620.h @@ -353,7 +353,7 @@ #define REG_TTXNUMB 0x0116 #define MSK_TTXNUMB_TTX_AFFCTRL_3_0 0xf0 #define BIT_TTXNUMB_TTX_COM1_AT_SYNC_WAIT BIT(3) -#define MSK_TTXNUMB_TTX_NUMBPS_2_0 0x07 +#define MSK_TTXNUMB_TTX_NUMBPS 0x07
/* TDM TX NUMSPISYM, default value: 0x04 */ #define REG_TTXSPINUMS 0x0117 @@ -433,12 +433,14 @@
/* HSIC Keeper, default value: 0x00 */ #define REG_KEEPER 0x0181 -#define MSK_KEEPER_KEEPER_MODE_1_0 0x03 +#define MSK_KEEPER_MODE 0x03 +#define VAL_KEEPER_MODE_HOST 0 +#define VAL_KEEPER_MODE_DEVICE 2
/* HSIC Flow Control General, default value: 0x02 */ #define REG_FCGC 0x0183 -#define BIT_FCGC_HSIC_FC_HOSTMODE BIT(1) -#define BIT_FCGC_HSIC_FC_ENABLE BIT(0) +#define BIT_FCGC_HSIC_HOSTMODE BIT(1) +#define BIT_FCGC_HSIC_ENABLE BIT(0)
/* HSIC Flow Control CTR13, default value: 0xfc */ #define REG_FCCTR13 0x0191
Since all sub-protocols of MHL3 are already supported MHL3 mode can be enabled. With this patch it is possible to use packed pixel modes and clocks up to 300MHz - 1920x1080@60Hz and 4K modes.
Signed-off-by: Andrzej Hajda a.hajda@samsung.com --- drivers/gpu/drm/bridge/sil-sii8620.c | 23 ++++++++++++----------- 1 file changed, 12 insertions(+), 11 deletions(-)
diff --git a/drivers/gpu/drm/bridge/sil-sii8620.c b/drivers/gpu/drm/bridge/sil-sii8620.c index be7be3c..7cfa1a7 100644 --- a/drivers/gpu/drm/bridge/sil-sii8620.c +++ b/drivers/gpu/drm/bridge/sil-sii8620.c @@ -1403,8 +1403,7 @@ static void sii8620_mhl_init(struct sii8620 *ctx) ); sii8620_disable_gen2_write_burst(ctx);
- /* currently MHL3 is not supported, so we force version to 0 */ - sii8620_mt_write_stat(ctx, MHL_DST_REG(VERSION), 0); + sii8620_mt_write_stat(ctx, MHL_DST_REG(VERSION), SII8620_MHL_VERSION); sii8620_mt_write_stat(ctx, MHL_DST_REG(CONNECTED_RDY), MHL_DST_CONN_DCAP_RDY | MHL_DST_CONN_XDEVCAPP_SUPP | MHL_DST_CONN_POW_STAT); @@ -1671,14 +1670,16 @@ static void sii8620_irq_g2wb(struct sii8620 *ctx) sii8620_write(ctx, REG_MDT_INT_0, stat); }
-static void sii8620_status_changed_dcap(struct sii8620 *ctx) +static void sii8620_status_dcap_ready(struct sii8620 *ctx) { - if (ctx->stat[MHL_DST_CONNECTED_RDY] & MHL_DST_CONN_DCAP_RDY) { - sii8620_set_mode(ctx, CM_MHL1); - sii8620_peer_specific_init(ctx); - sii8620_write(ctx, REG_INTR9_MASK, BIT_INTR9_DEVCAP_DONE - | BIT_INTR9_EDID_DONE | BIT_INTR9_EDID_ERROR); - } + enum sii8620_mode mode; + + mode = ctx->stat[MHL_DST_VERSION] >= 0x30 ? CM_MHL3 : CM_MHL1; + if (mode > ctx->mode) + sii8620_set_mode(ctx, mode); + sii8620_peer_specific_init(ctx); + sii8620_write(ctx, REG_INTR9_MASK, BIT_INTR9_DEVCAP_DONE + | BIT_INTR9_EDID_DONE | BIT_INTR9_EDID_ERROR); }
static void sii8620_status_changed_path(struct sii8620 *ctx) @@ -1706,8 +1707,8 @@ static void sii8620_msc_mr_write_stat(struct sii8620 *ctx) sii8620_update_array(ctx->stat, st, MHL_DST_SIZE); sii8620_update_array(ctx->xstat, xst, MHL_XDS_SIZE);
- if (st[MHL_DST_CONNECTED_RDY] & MHL_DST_CONN_DCAP_RDY) - sii8620_status_changed_dcap(ctx); + if (ctx->stat[MHL_DST_CONNECTED_RDY] & MHL_DST_CONN_DCAP_RDY) + sii8620_status_dcap_ready(ctx);
if (st[MHL_DST_LINK_MODE] & MHL_DST_LM_PATH_ENABLED) sii8620_status_changed_path(ctx);
Bug in DECON(CRTC) driver prevented interlace modes from proper work. Since DECON is fixed interlace modes can be enabled in MHL.
Signed-off-by: Andrzej Hajda a.hajda@samsung.com --- drivers/gpu/drm/bridge/sil-sii8620.c | 3 --- 1 file changed, 3 deletions(-)
diff --git a/drivers/gpu/drm/bridge/sil-sii8620.c b/drivers/gpu/drm/bridge/sil-sii8620.c index 7cfa1a7..f0532b8 100644 --- a/drivers/gpu/drm/bridge/sil-sii8620.c +++ b/drivers/gpu/drm/bridge/sil-sii8620.c @@ -2114,9 +2114,6 @@ static bool sii8620_mode_fixup(struct drm_bridge *bridge, int max_lclk; bool ret = true;
- if (adjusted_mode->flags & DRM_MODE_FLAG_INTERLACE) - return false; - mutex_lock(&ctx->lock);
max_lclk = sii8620_is_mhl3(ctx) ? MHL3_MAX_LCLK : MHL1_MAX_LCLK;
On 02/01/2017 01:17 PM, Andrzej Hajda wrote:
Hi Archit,
Sorry for spamming, forgot to add the list.
This quite big patchset adds support for 4K Ultra HD modes in SiI8620 MHL bridge. To support it full MHL3 protocol and its sub-protocols should be implemented. Patchset contains also various fixes for bugs discovered during development.
v3: - upper-cased enums - add missing include to patch 6 (thanks to kbuild test robot)
queued to drm-misc-next after resolving some trivial checkpatch issues.
Archit
Regards Andrzej
Andrzej Hajda (25): drm/bridge/sii8620: simplify MHL3 mode setting drm/bridge/sii8620: add MHL3 mode check helper drm/bridge/sii8620: add reading device capability registers drm/bridge/sii8620: add continuations to messages drm/bridge/sii8620: initial support for eCBUS-S mode drm/bridge/mhl: add write burst related definitions drm/bridge/sii8620: add support for burst eMSC transmissions drm/bridge/sii8620: respond to feature requests drm/bridge/sii8620: fix peer device capabilities read code drm/bridge/sii8620: remove spare CBUS bring-up sequence drm/bridge/sii8620: fix MSC message removal drm/bridge/sii8620: fix initialization sequence for MHL2 receivers drm/bridge/sii8620: abstract out sink detection code drm/bridge/sii8620: set gen2 write burst before sending MSC command drm/bridge/sii8620: do not stop MHL output when TMDS input is stopped drm/bridge/sii8620: add delay during cbus reset drm/bridge/sii8620: split EDID read and write code drm/bridge/sii8620: fix disconnect sequence drm/bridge/mhl: add MHL3 infoframe related definitions drm/bridge/sii8620: rewrite hdmi start sequence drm/bridge/sii8620: send EMSC features on request drm/bridge/sii8620: improve gen2 write burst IRQ routine drm/bridge/sii8620: add HSIC initialization code drm/bridge/sii8620: enable MHL3 mode if possible drm/bridge/sii8620: enable interlace modes
drivers/gpu/drm/bridge/sil-sii8620.c | 948 ++++++++++++++++++++++++++++++----- drivers/gpu/drm/bridge/sil-sii8620.h | 50 +- include/drm/bridge/mhl.h | 85 ++++ 3 files changed, 933 insertions(+), 150 deletions(-)
dri-devel@lists.freedesktop.org
-
Andrzej Hajda -
Archit Taneja