When testing with a panel that's apparently a little more persnickety about the correct power sequence (specifically Samsung ATNA33XC20), we found that the ti-sn65dsi86 was doing things just slightly wrong.

Looking closely at the ti-sn65dsi86's datasheet, the power off sequence is supposed to be: 1. Clear VSTREAM_ENABLE bit 2. Stop DSI stream from GPU. DSI lanes must be placed in LP11 state. 3. Program the ML_TX_MODE to 0x0 (OFF) 4. Program the DP_NUM_LANES register to 0x0 5. Clear the DP_PLL_EN bit. 6. Deassert the EN pin. 7. Remove power from supply pins

Since we were doing the whole sequence in the "disable", I believe that step #2 (stopping the DSI stream from the GPU) wasn't happening. We also weren't setting DP_NUM_LANES to 0.

Let's fix this.

NOTE: things are a little asymmetric now. For instance, we turn the PLL on in "enable" but now we're not turning it off until "post_disable". It would seem to make sense to move the PLL turning on to "pre_enable" to match. Unfortunately, I don't believe that's allowed. It looks as if (in the non-refclk mode which probably nobody is using) we have to wait until the MIPI clock is there before we can enable the PLL. In any case, the way it is here won't really hurt--it'll just leave the PLL on a little longer.

Fixes: a095f15c00e2 ("drm/bridge: add support for sn65dsi86 bridge driver") Signed-off-by: Douglas Anderson dianders@chromium.org Acked-by: Robert Foss robert.foss@linaro.org Reviewed-by: Sean Paul seanpaul@chromium.org ---

(no changes since v1)

drivers/gpu/drm/bridge/ti-sn65dsi86.c | 11 +++++++---- 1 file changed, 7 insertions(+), 4 deletions(-)

diff --git a/drivers/gpu/drm/bridge/ti-sn65dsi86.c b/drivers/gpu/drm/bridge/ti-sn65dsi86.c index 9bf889302bcc..5e932070a1c3 100644 --- a/drivers/gpu/drm/bridge/ti-sn65dsi86.c +++ b/drivers/gpu/drm/bridge/ti-sn65dsi86.c @@ -766,10 +766,6 @@ static void ti_sn_bridge_disable(struct drm_bridge *bridge)

/* disable video stream */ regmap_update_bits(pdata->regmap, SN_ENH_FRAME_REG, VSTREAM_ENABLE, 0); - /* semi auto link training mode OFF */ - regmap_write(pdata->regmap, SN_ML_TX_MODE_REG, 0); - /* disable DP PLL */ - regmap_write(pdata->regmap, SN_PLL_ENABLE_REG, 0); }

static void ti_sn_bridge_set_dsi_rate(struct ti_sn65dsi86 *pdata) @@ -1106,6 +1102,13 @@ static void ti_sn_bridge_post_disable(struct drm_bridge *bridge) { struct ti_sn65dsi86 *pdata = bridge_to_ti_sn65dsi86(bridge);

+ /* semi auto link training mode OFF */ + regmap_write(pdata->regmap, SN_ML_TX_MODE_REG, 0); + /* Num lanes to 0 as per power sequencing in data sheet */ + regmap_update_bits(pdata->regmap, SN_SSC_CONFIG_REG, DP_NUM_LANES_MASK, 0); + /* disable DP PLL */ + regmap_write(pdata->regmap, SN_PLL_ENABLE_REG, 0); + if (!pdata->refclk) ti_sn65dsi86_disable_comms(pdata);

This reverts commit 4bfe6c8f7c23b01719671b69fd29b87a35ccd9d6.

This panel's power sequencing really can't be handled properly by panel-simple because of the special sequencing needed for the EL_ON3 GPIO. The only way it was sorta working in the past was by trying to jam that signal into the "enable-gpio", but that really wasn't a good fit. We'll add a custom panel driver for this panel to do it right.

Signed-off-by: Douglas Anderson dianders@chromium.org Reviewed-by: Sean Paul seanpaul@chromium.org ---

(no changes since v1)

drivers/gpu/drm/panel/panel-simple.c | 33 ---------------------------- 1 file changed, 33 deletions(-)

diff --git a/drivers/gpu/drm/panel/panel-simple.c b/drivers/gpu/drm/panel/panel-simple.c index 9b286bd4444f..c8694f7f8e0f 100644 --- a/drivers/gpu/drm/panel/panel-simple.c +++ b/drivers/gpu/drm/panel/panel-simple.c @@ -3621,36 +3621,6 @@ static const struct panel_desc rocktech_rk101ii01d_ct = { .connector_type = DRM_MODE_CONNECTOR_LVDS, };

-static const struct drm_display_mode samsung_atna33xc20_mode = { - .clock = 138770, - .hdisplay = 1920, - .hsync_start = 1920 + 48, - .hsync_end = 1920 + 48 + 32, - .htotal = 1920 + 48 + 32 + 80, - .vdisplay = 1080, - .vsync_start = 1080 + 8, - .vsync_end = 1080 + 8 + 8, - .vtotal = 1080 + 8 + 8 + 16, - .flags = DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_NVSYNC, -}; - -static const struct panel_desc samsung_atna33xc20 = { - .modes = &samsung_atna33xc20_mode, - .num_modes = 1, - .bpc = 10, - .size = { - .width = 294, - .height = 165, - }, - .delay = { - .disable_to_power_off = 200, - .power_to_enable = 400, - .hpd_absent_delay = 200, - .unprepare = 500, - }, - .connector_type = DRM_MODE_CONNECTOR_eDP, -}; - static const struct drm_display_mode samsung_lsn122dl01_c01_mode = { .clock = 271560, .hdisplay = 2560, @@ -4657,9 +4627,6 @@ static const struct of_device_id platform_of_match[] = { }, { .compatible = "rocktech,rk101ii01d-ct", .data = &rocktech_rk101ii01d_ct, - }, { - .compatible = "samsung,atna33xc20", - .data = &samsung_atna33xc20, }, { .compatible = "samsung,lsn122dl01-c01", .data = &samsung_lsn122dl01_c01,

The Samsung ATNA33XC20 panel is an AMOLED eDP panel that has backlight control over the DP AUX channel.

This panel is _almost_ able to be controlled in a "simple" way (and it originally was implemented in panel-simple.c), but it's really impossible to get the backlight semantics right there without adding wacky special-case code to panel-simple. Let's give up and clone the parts of panel-simple that we need and implement the power sequence that this panel needs.

NOTE: we'll still leave the devicetree bindings alone. Even though the power-sequencing is non-standard the bindings are still "simple".

Signed-off-by: Douglas Anderson dianders@chromium.org Reviewed-by: Sean Paul seanpaul@chromium.org ---

(no changes since v1)

drivers/gpu/drm/panel/Kconfig | 12 + drivers/gpu/drm/panel/Makefile | 1 + .../gpu/drm/panel/panel-samsung-atna33xc20.c | 366 ++++++++++++++++++ 3 files changed, 379 insertions(+) create mode 100644 drivers/gpu/drm/panel/panel-samsung-atna33xc20.c

diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig index 6b3eb041182c..58430d358489 100644 --- a/drivers/gpu/drm/panel/Kconfig +++ b/drivers/gpu/drm/panel/Kconfig @@ -353,6 +353,18 @@ config DRM_PANEL_RONBO_RB070D30 Say Y here if you want to enable support for Ronbo Electronics RB070D30 1024x600 DSI panel.

+config DRM_PANEL_SAMSUNG_ATNA33XC20 + tristate "Samsung ATNA33XC20 eDP panel" + depends on OF + depends on BACKLIGHT_CLASS_DEVICE + depends on PM + select VIDEOMODE_HELPERS + select DRM_DP_AUX_BUS + help + DRM panel driver for the Samsung ATNA33XC20 panel. This panel can't + be handled by the DRM_PANEL_SIMPLE driver because its power + sequencing is non-standard. + config DRM_PANEL_SAMSUNG_DB7430 tristate "Samsung DB7430-based DPI panels" depends on OF && SPI && GPIOLIB diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile index 08debae9b314..1b6fe2008861 100644 --- a/drivers/gpu/drm/panel/Makefile +++ b/drivers/gpu/drm/panel/Makefile @@ -34,6 +34,7 @@ obj-$(CONFIG_DRM_PANEL_RASPBERRYPI_TOUCHSCREEN) += panel-raspberrypi-touchscreen obj-$(CONFIG_DRM_PANEL_RAYDIUM_RM67191) += panel-raydium-rm67191.o obj-$(CONFIG_DRM_PANEL_RAYDIUM_RM68200) += panel-raydium-rm68200.o obj-$(CONFIG_DRM_PANEL_RONBO_RB070D30) += panel-ronbo-rb070d30.o +obj-$(CONFIG_DRM_PANEL_SAMSUNG_ATNA33XC20) += panel-samsung-atna33xc20.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_DB7430) += panel-samsung-db7430.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_LD9040) += panel-samsung-ld9040.o obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6D16D0) += panel-samsung-s6d16d0.o diff --git a/drivers/gpu/drm/panel/panel-samsung-atna33xc20.c b/drivers/gpu/drm/panel/panel-samsung-atna33xc20.c new file mode 100644 index 000000000000..221db6512859 --- /dev/null +++ b/drivers/gpu/drm/panel/panel-samsung-atna33xc20.c @@ -0,0 +1,366 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright 2021 Google Inc. + * + * Panel driver for the Samsung ATNA33XC20 panel. This panel can't be handled + * by the DRM_PANEL_SIMPLE driver because its power sequencing is non-standard. + */ + +#include <linux/backlight.h> +#include <linux/delay.h> +#include <linux/gpio/consumer.h> +#include <linux/iopoll.h> +#include <linux/module.h> +#include <linux/pm_runtime.h> +#include <linux/regulator/consumer.h> + +#include <drm/drm_dp_aux_bus.h> +#include <drm/drm_dp_helper.h> +#include <drm/drm_edid.h> +#include <drm/drm_panel.h> + +struct atana33xc20_panel { + struct drm_panel base; + bool prepared; + bool enabled; + bool el3_was_on; + + bool no_hpd; + struct gpio_desc *hpd_gpio; + + struct regulator *supply; + struct gpio_desc *el_on3_gpio; + + struct edid *edid; + + ktime_t powered_off_time; + ktime_t powered_on_time; + ktime_t el_on3_off_time; +}; + +static inline struct atana33xc20_panel *to_atana33xc20(struct drm_panel *panel) +{ + return container_of(panel, struct atana33xc20_panel, base); +} + +static void atana33xc20_wait(ktime_t start_ktime, unsigned int min_ms) +{ + ktime_t now_ktime, min_ktime; + + min_ktime = ktime_add(start_ktime, ms_to_ktime(min_ms)); + now_ktime = ktime_get(); + + if (ktime_before(now_ktime, min_ktime)) + msleep(ktime_to_ms(ktime_sub(min_ktime, now_ktime)) + 1); +} + +static int atana33xc20_suspend(struct device *dev) +{ + struct atana33xc20_panel *p = dev_get_drvdata(dev); + int ret; + + /* + * Note 3 (Example of power off sequence in detail) in spec + * specifies to wait 150 ms after deasserting EL3_ON before + * powering off. + */ + if (p->el3_was_on) + atana33xc20_wait(p->el_on3_off_time, 150); + + ret = regulator_disable(p->supply); + if (ret) + return ret; + p->powered_off_time = ktime_get(); + p->el3_was_on = false; + + return 0; +} + +static int atana33xc20_resume(struct device *dev) +{ + struct atana33xc20_panel *p = dev_get_drvdata(dev); + bool hpd_asserted = false; + int ret; + + /* T12 (Power off time) is min 500 ms */ + atana33xc20_wait(p->powered_off_time, 500); + + ret = regulator_enable(p->supply); + if (ret) + return ret; + p->powered_on_time = ktime_get(); + + /* + * Handle HPD. Note: if HPD is hooked up to a dedicated pin on the + * eDP controller then "no_hpd" will be false _and_ "hpd_gpio" will be + * NULL. It's up to the controller driver to wait for HPD after + * preparing the panel in that case. + */ + if (p->no_hpd) { + /* T3 VCC to HPD high is max 200 ms */ + msleep(200); + } else if (p->hpd_gpio) { + ret = readx_poll_timeout(gpiod_get_value_cansleep, p->hpd_gpio, + hpd_asserted, hpd_asserted, + 1000, 200000); + if (!hpd_asserted) + dev_warn(dev, "Timeout waiting for HPD\n"); + } + + return 0; +} + +static int atana33xc20_disable(struct drm_panel *panel) +{ + struct atana33xc20_panel *p = to_atana33xc20(panel); + + /* Disabling when already disabled is a no-op */ + if (!p->enabled) + return 0; + + gpiod_set_value_cansleep(p->el_on3_gpio, 0); + p->el_on3_off_time = ktime_get(); + p->enabled = false; + + /* + * Keep track of the fact that EL_ON3 was on but we haven't power + * cycled yet. This lets us know that "el_on3_off_time" is recent (we + * don't need to worry about ktime wraparounds) and also makes it + * obvious if we try to enable again without a power cycle (see the + * warning in atana33xc20_enable()). + */ + p->el3_was_on = true; + + /* + * Sleeping 20 ms here (after setting the GPIO) avoids a glitch when + * powering off. + */ + msleep(20); + + return 0; +} + +static int atana33xc20_enable(struct drm_panel *panel) +{ + struct atana33xc20_panel *p = to_atana33xc20(panel); + + /* Enabling when already enabled is a no-op */ + if (p->enabled) + return 0; + + /* + * Once EL_ON3 drops we absolutely need a power cycle before the next + * enable or the backlight will never come on again. The code ensures + * this because disable() is _always_ followed by unprepare() and + * unprepare() forces a suspend with pm_runtime_put_sync_suspend(), + * but let's track just to make sure since the requirement is so + * non-obvious. + */ + if (WARN_ON(p->el3_was_on)) + return -EIO; + + /* + * Note 2 (Example of power on sequence in detail) in spec specifies + * to wait 400 ms after powering on before asserting EL3_on. + */ + atana33xc20_wait(p->powered_on_time, 400); + + gpiod_set_value_cansleep(p->el_on3_gpio, 1); + p->enabled = true; + + return 0; +} + +static int atana33xc20_unprepare(struct drm_panel *panel) +{ + struct atana33xc20_panel *p = to_atana33xc20(panel); + int ret; + + /* Unpreparing when already unprepared is a no-op */ + if (!p->prepared) + return 0; + + /* + * Purposely do a put_sync, don't use autosuspend. The panel's tcon + * seems to sometimes crash when you stop giving it data and this is + * the best way to ensure it will come back. + * + * NOTE: we still want autosuspend for cases where we only turn on + * to get the EDID or otherwise send DP AUX commands to the panel. + */ + ret = pm_runtime_put_sync_suspend(panel->dev); + if (ret < 0) + return ret; + p->prepared = false; + + return 0; +} + +static int atana33xc20_prepare(struct drm_panel *panel) +{ + struct atana33xc20_panel *p = to_atana33xc20(panel); + int ret; + + /* Preparing when already prepared is a no-op */ + if (p->prepared) + return 0; + + ret = pm_runtime_get_sync(panel->dev); + if (ret < 0) { + pm_runtime_put_autosuspend(panel->dev); + return ret; + } + p->prepared = true; + + return 0; +} + +static int atana33xc20_get_modes(struct drm_panel *panel, + struct drm_connector *connector) +{ + struct atana33xc20_panel *p = to_atana33xc20(panel); + struct dp_aux_ep_device *aux_ep = to_dp_aux_ep_dev(panel->dev); + int num = 0; + + pm_runtime_get_sync(panel->dev); + + if (!p->edid) + p->edid = drm_get_edid(connector, &aux_ep->aux->ddc); + num = drm_add_edid_modes(connector, p->edid); + + pm_runtime_mark_last_busy(panel->dev); + pm_runtime_put_autosuspend(panel->dev); + + return num; +} + +static const struct drm_panel_funcs atana33xc20_funcs = { + .disable = atana33xc20_disable, + .enable = atana33xc20_enable, + .unprepare = atana33xc20_unprepare, + .prepare = atana33xc20_prepare, + .get_modes = atana33xc20_get_modes, +}; + +static void atana33xc20_runtime_disable(void *data) +{ + pm_runtime_disable(data); +} + +static void atana33xc20_dont_use_autosuspend(void *data) +{ + pm_runtime_dont_use_autosuspend(data); +} + +static int atana33xc20_probe(struct dp_aux_ep_device *aux_ep) +{ + struct atana33xc20_panel *panel; + struct device *dev = &aux_ep->dev; + int ret; + + panel = devm_kzalloc(dev, sizeof(*panel), GFP_KERNEL); + if (!panel) + return -ENOMEM; + dev_set_drvdata(dev, panel); + + panel->supply = devm_regulator_get(dev, "power"); + if (IS_ERR(panel->supply)) + return dev_err_probe(dev, PTR_ERR(panel->supply), + "Failed to get power supply\n"); + + panel->el_on3_gpio = devm_gpiod_get(dev, "enable", GPIOD_OUT_LOW); + if (IS_ERR(panel->el_on3_gpio)) + return dev_err_probe(dev, PTR_ERR(panel->el_on3_gpio), + "Failed to get enable GPIO\n"); + + panel->no_hpd = of_property_read_bool(dev->of_node, "no-hpd"); + if (!panel->no_hpd) { + panel->hpd_gpio = devm_gpiod_get_optional(dev, "hpd", GPIOD_IN); + if (IS_ERR(panel->hpd_gpio)) + return dev_err_probe(dev, PTR_ERR(panel->hpd_gpio), + "Failed to get HPD GPIO\n"); + } + + pm_runtime_enable(dev); + ret = devm_add_action_or_reset(dev, atana33xc20_runtime_disable, dev); + if (ret) + return ret; + pm_runtime_set_autosuspend_delay(dev, 1000); + pm_runtime_use_autosuspend(dev); + ret = devm_add_action_or_reset(dev, atana33xc20_dont_use_autosuspend, dev); + if (ret) + return ret; + + drm_panel_init(&panel->base, dev, &atana33xc20_funcs, DRM_MODE_CONNECTOR_eDP); + + pm_runtime_get_sync(dev); + ret = drm_panel_dp_aux_backlight(&panel->base, aux_ep->aux); + pm_runtime_mark_last_busy(dev); + pm_runtime_put_autosuspend(dev); + if (ret) + return dev_err_probe(dev, ret, + "failed to register dp aux backlight\n"); + + drm_panel_add(&panel->base); + + return 0; +} + +static void atana33xc20_remove(struct dp_aux_ep_device *aux_ep) +{ + struct device *dev = &aux_ep->dev; + struct atana33xc20_panel *panel = dev_get_drvdata(dev); + + drm_panel_remove(&panel->base); + drm_panel_disable(&panel->base); + drm_panel_unprepare(&panel->base); + + kfree(panel->edid); +} + +static void atana33xc20_shutdown(struct dp_aux_ep_device *aux_ep) +{ + struct device *dev = &aux_ep->dev; + struct atana33xc20_panel *panel = dev_get_drvdata(dev); + + drm_panel_disable(&panel->base); + drm_panel_unprepare(&panel->base); +} + +static const struct of_device_id atana33xc20_dt_match[] = { + { .compatible = "samsung,atna33xc20", }, + { /* sentinal */ } +}; +MODULE_DEVICE_TABLE(of, atana33xc20_dt_match); + +static const struct dev_pm_ops atana33xc20_pm_ops = { + SET_RUNTIME_PM_OPS(atana33xc20_suspend, atana33xc20_resume, NULL) + SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend, + pm_runtime_force_resume) +}; + +static struct dp_aux_ep_driver atana33xc20_driver = { + .driver = { + .name = "samsung_atana33xc20", + .of_match_table = atana33xc20_dt_match, + .pm = &atana33xc20_pm_ops, + }, + .probe = atana33xc20_probe, + .remove = atana33xc20_remove, + .shutdown = atana33xc20_shutdown, +}; + +static int __init atana33xc20_init(void) +{ + return dp_aux_dp_driver_register(&atana33xc20_driver); +} +module_init(atana33xc20_init); + +static void __exit atana33xc20_exit(void) +{ + dp_aux_dp_driver_unregister(&atana33xc20_driver); +} +module_exit(atana33xc20_exit); + +MODULE_DESCRIPTION("Samsung ATANA33XC20 Panel Driver"); +MODULE_LICENSE("GPL v2");