The implicit BLCK divider setting was broken by "ASoC: mcasp: don't override bclk divider if it was provided by the machine"-patch. After the BCLK divider is implicitly set for the first time the mcasp->bclk_div gets a non zero value and the implicit setting is "turned off".

Signed-off-by: Jyri Sarha jsarha@ti.com --- sound/soc/davinci/davinci-mcasp.c | 14 +++++++++++--- 1 file changed, 11 insertions(+), 3 deletions(-)

diff --git a/sound/soc/davinci/davinci-mcasp.c b/sound/soc/davinci/davinci-mcasp.c index c28508d..6a6b2ff 100644 --- a/sound/soc/davinci/davinci-mcasp.c +++ b/sound/soc/davinci/davinci-mcasp.c @@ -403,7 +403,8 @@ out: return ret; }

-static int davinci_mcasp_set_clkdiv(struct snd_soc_dai *dai, int div_id, int div) +static int __davinci_mcasp_set_clkdiv(struct snd_soc_dai *dai, int div_id, + int div, bool explicit) { struct davinci_mcasp *mcasp = snd_soc_dai_get_drvdata(dai);

@@ -420,7 +421,8 @@ static int davinci_mcasp_set_clkdiv(struct snd_soc_dai *dai, int div_id, int div ACLKXDIV(div - 1), ACLKXDIV_MASK); mcasp_mod_bits(mcasp, DAVINCI_MCASP_ACLKRCTL_REG, ACLKRDIV(div - 1), ACLKRDIV_MASK); - mcasp->bclk_div = div; + if (explicit) + mcasp->bclk_div = div; break;

case 2: /* BCLK/LRCLK ratio */ @@ -434,6 +436,12 @@ static int davinci_mcasp_set_clkdiv(struct snd_soc_dai *dai, int div_id, int div return 0; }

+static int davinci_mcasp_set_clkdiv(struct snd_soc_dai *dai, int div_id, + int div) +{ + return __davinci_mcasp_set_clkdiv(dai, div_id, div, 1); +} + static int davinci_mcasp_set_sysclk(struct snd_soc_dai *dai, int clk_id, unsigned int freq, int dir) { @@ -738,7 +746,7 @@ static int davinci_mcasp_hw_params(struct snd_pcm_substream *substream, "Inaccurate BCLK: %u Hz / %u != %u Hz\n", mcasp->sysclk_freq, div, bclk_freq); } - davinci_mcasp_set_clkdiv(cpu_dai, 1, div); + __davinci_mcasp_set_clkdiv(cpu_dai, 1, div, 0); }

ret = mcasp_common_hw_param(mcasp, substream->stream,

The added clk-gpio is a basic clock that can be enabled and disabled trough a gpio output. The DT binding document for the clock is also added. For EPROBE_DEFER handling the registering of the clock has to be delayed until of_clk_get() call time.

Signed-off-by: Jyri Sarha jsarha@ti.com --- .../devicetree/bindings/clock/gpio-clock.txt | 21 ++ drivers/clk/Makefile | 1 + drivers/clk/clk-gpio.c | 206 ++++++++++++++++++++ include/linux/clk-provider.h | 23 +++ 4 files changed, 251 insertions(+) create mode 100644 Documentation/devicetree/bindings/clock/gpio-clock.txt create mode 100644 drivers/clk/clk-gpio.c

diff --git a/Documentation/devicetree/bindings/clock/gpio-clock.txt b/Documentation/devicetree/bindings/clock/gpio-clock.txt new file mode 100644 index 0000000..54fea39 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/gpio-clock.txt @@ -0,0 +1,21 @@ +Binding for simple gpio controlled clock. + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be "gpio-clock". +- #clock-cells : from common clock binding; shall be set to 0. +- enable-gpios : GPIO reference for enabling and disabling the clock. + +Optional properties: +- clocks: Maximum of one parent clock is supported. + +Example: + clock { + compatible = "gpio-clock"; + clocks = <&parentclk>; + #clock-cells = <0>; + enable-gpios = <&gpio 1 GPIO_ACTIVE_HIGH>; + }; diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile index 567f102..bde8fdf 100644 --- a/drivers/clk/Makefile +++ b/drivers/clk/Makefile @@ -9,6 +9,7 @@ obj-$(CONFIG_COMMON_CLK) += clk-gate.o obj-$(CONFIG_COMMON_CLK) += clk-mux.o obj-$(CONFIG_COMMON_CLK) += clk-composite.o obj-$(CONFIG_COMMON_CLK) += clk-fractional-divider.o +obj-$(CONFIG_COMMON_CLK) += clk-gpio.o

# hardware specific clock types # please keep this section sorted lexicographically by file/directory path name diff --git a/drivers/clk/clk-gpio.c b/drivers/clk/clk-gpio.c new file mode 100644 index 0000000..1eff97c --- /dev/null +++ b/drivers/clk/clk-gpio.c @@ -0,0 +1,206 @@ +/* + * Copyright (C) 2012 - 2014 Texas Instruments Incorporated - http://www.ti.com + * Author: Jyri Sarha jsarha@ti.com + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * Gpio controlled clock implementation + */ + +#include <linux/clk-provider.h> +#include <linux/module.h> +#include <linux/slab.h> +#include <linux/gpio.h> +#include <linux/of_gpio.h> +#include <linux/err.h> +#include <linux/device.h> + +/** + * DOC: basic gpio controlled clock which can be enabled and disabled + * with gpio output + * Traits of this clock: + * prepare - clk_(un)prepare only ensures parent is (un)prepared + * enable - clk_enable and clk_disable are functional & control gpio + * rate - inherits rate from parent. No clk_set_rate support + * parent - fixed parent. No clk_set_parent support + */ + +#define to_clk_gpio(_hw) container_of(_hw, struct clk_gpio, hw) + +static int clk_gpio_enable(struct clk_hw *hw) +{ + struct clk_gpio *clk = to_clk_gpio(hw); + + gpiod_set_value(clk->gpiod, 1); + + return 0; +} + +static void clk_gpio_disable(struct clk_hw *hw) +{ + struct clk_gpio *clk = to_clk_gpio(hw); + + gpiod_set_value(clk->gpiod, 0); +} + +static int clk_gpio_is_enabled(struct clk_hw *hw) +{ + struct clk_gpio *clk = to_clk_gpio(hw); + + return gpiod_get_value(clk->gpiod); +} + +const struct clk_ops clk_gpio_ops = { + .enable = clk_gpio_enable, + .disable = clk_gpio_disable, + .is_enabled = clk_gpio_is_enabled, +}; +EXPORT_SYMBOL_GPL(clk_gpio_ops); + +/** + * clk_register_gpio - register a gpip clock with the clock framework + * @dev: device that is registering this clock + * @name: name of this clock + * @parent_name: name of this clock's parent + * @gpiod: gpio descriptor to control this clock + */ +struct clk *clk_register_gpio(struct device *dev, const char *name, + const char *parent_name, struct gpio_desc *gpiod, + unsigned long flags) +{ + struct clk_gpio *clk_gpio = NULL; + struct clk *clk = ERR_PTR(-EINVAL); + struct clk_init_data init = { NULL }; + unsigned long gpio_flags; + int err; + + if (gpiod_is_active_low(gpiod)) + gpio_flags = GPIOF_OUT_INIT_HIGH; + else + gpio_flags = GPIOF_OUT_INIT_LOW; + + if (dev) + err = devm_gpio_request_one(dev, desc_to_gpio(gpiod), + gpio_flags, name); + else + err = gpio_request_one(desc_to_gpio(gpiod), gpio_flags, name); + + if (err) { + pr_err("%s: %s: Error requesting clock control gpio %u\n", + __func__, name, desc_to_gpio(gpiod)); + return ERR_PTR(err); + } + + if (dev) + clk_gpio = devm_kzalloc(dev, sizeof(struct clk_gpio), + GFP_KERNEL); + else + clk_gpio = kzalloc(sizeof(struct clk_gpio), GFP_KERNEL); + + if (!clk_gpio) { + pr_err("%s: %s: could not allocate gpio clk\n", __func__, name); + clk = ERR_PTR(-ENOMEM); + goto clk_register_gpio_err; + } + + init.name = name; + init.ops = &clk_gpio_ops; + init.flags = flags | CLK_IS_BASIC; + init.parent_names = (parent_name ? &parent_name : NULL); + init.num_parents = (parent_name ? 1 : 0); + + clk_gpio->gpiod = gpiod; + clk_gpio->hw.init = &init; + + clk = clk_register(dev, &clk_gpio->hw); + + if (!IS_ERR(clk)) + return clk; + + if (!dev) + kfree(clk_gpio); + +clk_register_gpio_err: + gpiod_put(gpiod); + + return clk; +} +EXPORT_SYMBOL_GPL(clk_register_gpio); + +#ifdef CONFIG_OF +/** + * The clk_register_gpio has to be delayed, because the EPROBE_DEFER + * can not be handled properly at of_clk_init() call time. + */ + +struct clk_gpio_delayed_register_data { + struct device_node *node; + struct mutex lock; + struct clk *clk; +}; + +struct clk *of_clk_gpio_delayed_register_get(struct of_phandle_args *clkspec, + void *_data) +{ + struct clk_gpio_delayed_register_data *data = _data; + struct clk *clk; + const char *clk_name = data->node->name; + const char *parent_name; + struct gpio_desc *gpiod; + int gpio; + + mutex_lock(&data->lock); + + if (data->clk) { + mutex_unlock(&data->lock); + return data->clk; + } + + gpio = of_get_named_gpio_flags(data->node, "enable-gpios", 0, NULL); + if (gpio < 0) { + mutex_unlock(&data->lock); + if (gpio != -EPROBE_DEFER) + pr_err("%s: %s: Can't get 'enable-gpios' DT property\n", + __func__, clk_name); + return ERR_PTR(gpio); + } + gpiod = gpio_to_desc(gpio); + + parent_name = of_clk_get_parent_name(data->node, 0); + + clk = clk_register_gpio(NULL, clk_name, parent_name, gpiod, 0); + if (IS_ERR(clk)) { + mutex_unlock(&data->lock); + return clk; + } + + data->clk = clk; + mutex_unlock(&data->lock); + + return clk; +} + +/** + * of_gpio_clk_setup() - Setup function for gpio controlled clock + */ +void __init of_gpio_clk_setup(struct device_node *node) +{ + struct clk_gpio_delayed_register_data *data; + + data = kzalloc(sizeof(struct clk_gpio_delayed_register_data), + GFP_KERNEL); + if (!data) { + pr_err("%s: could not allocate gpio clk\n", __func__); + return; + } + + data->node = node; + mutex_init(&data->lock); + + of_clk_add_provider(node, of_clk_gpio_delayed_register_get, data); +} +EXPORT_SYMBOL_GPL(of_gpio_clk_setup); +CLK_OF_DECLARE(gpio_clk, "gpio-clock", of_gpio_clk_setup); +#endif diff --git a/include/linux/clk-provider.h b/include/linux/clk-provider.h index 0c287db..09252d9 100644 --- a/include/linux/clk-provider.h +++ b/include/linux/clk-provider.h @@ -488,6 +488,29 @@ struct clk *clk_register_composite(struct device *dev, const char *name, struct clk_hw *gate_hw, const struct clk_ops *gate_ops, unsigned long flags);

+/*** + * struct clk_gpio - gpio controlled clock + * + * @hw: handle between common and hardware-specific interfaces + * @gpio: gpio + * @active_low: gpio polarity + * + * Clock with a gpio control for enabling and disabling the parent clock. + * Implements .enable, .disable and .is_enabled + */ + +struct clk_gpio { + struct clk_hw hw; + struct gpio_desc *gpiod; +}; + +extern const struct clk_ops clk_gpio_ops; +struct clk *clk_register_gpio(struct device *dev, const char *name, + const char *parent_name, struct gpio_desc *gpio, + unsigned long flags); + +void of_gpio_clk_setup(struct device_node *node); + /** * clk_register - allocate a new clock, register it and return an opaque cookie * @dev: device that is registering this clock

Add machine driver support for BeagleBone-Black HDMI audio. BBB has NXP TDA998X HDMI transmitter connected to McASP port in I2S mode. The 44100 Hz sample-rate and it's multiples can not be accurately produced on BBB. The only supported sample format is SNDRV_PCM_FORMAT_S32_LE. The 8 least significant bits are ignored.

Signed-off-by: Jyri Sarha jsarha@ti.com --- .../bindings/sound/davinci-evm-audio.txt | 4 +- sound/soc/davinci/davinci-evm.c | 82 +++++++++++++++++++- 2 files changed, 83 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/sound/davinci-evm-audio.txt b/Documentation/devicetree/bindings/sound/davinci-evm-audio.txt index 963e100..c137436 100644 --- a/Documentation/devicetree/bindings/sound/davinci-evm-audio.txt +++ b/Documentation/devicetree/bindings/sound/davinci-evm-audio.txt @@ -1,7 +1,9 @@ * Texas Instruments SoC audio setups with TLV320AIC3X Codec

Required properties: -- compatible : "ti,da830-evm-audio" : forDM365/DA8xx/OMAPL1x/AM33xx +- compatible : "ti,da830-evm-audio" : for DM365/DA8xx/OMAPL1x/AM33xx + "ti,am335x-beaglebone-black-audio" : for Beaglebone-black HDMI + audio - ti,model : The user-visible name of this sound complex. - ti,audio-codec : The phandle of the TLV320AIC3x audio codec - ti,mcasp-controller : The phandle of the McASP controller diff --git a/sound/soc/davinci/davinci-evm.c b/sound/soc/davinci/davinci-evm.c index a50010e..9b98667 100644 --- a/sound/soc/davinci/davinci-evm.c +++ b/sound/soc/davinci/davinci-evm.c @@ -21,6 +21,7 @@ #include <sound/core.h> #include <sound/pcm.h> #include <sound/soc.h> +#include <sound/pcm_params.h>

#include <asm/dma.h> #include <asm/mach-types.h> @@ -83,12 +84,46 @@ static int evm_hw_params(struct snd_pcm_substream *substream, return 0; }

+/* If changing sample format the tda998x configuration (REG_CTS_N) needs + to be changed. */ +#define TDA998X_SAMPLE_FORMAT SNDRV_PCM_FORMAT_S32_LE +static int evm_tda998x_startup(struct snd_pcm_substream *substream) +{ + struct snd_pcm_runtime *runtime = substream->runtime; + struct snd_mask *fmt = constrs_mask(&runtime->hw_constraints, + SNDRV_PCM_HW_PARAM_FORMAT); + snd_mask_none(fmt); + snd_mask_set(fmt, TDA998X_SAMPLE_FORMAT); + + return evm_startup(substream); +} + +static int evm_tda998x_hw_params(struct snd_pcm_substream *substream, + struct snd_pcm_hw_params *params) +{ + struct snd_soc_pcm_runtime *rtd = substream->private_data; + struct snd_soc_dai *cpu_dai = rtd->cpu_dai; + struct snd_soc_card *soc_card = rtd->card; + struct snd_soc_card_drvdata_davinci *drvdata = + snd_soc_card_get_drvdata(soc_card); + + return snd_soc_dai_set_sysclk(cpu_dai, 0, drvdata->sysclk, + SND_SOC_CLOCK_IN); +} + static struct snd_soc_ops evm_ops = { .startup = evm_startup, .shutdown = evm_shutdown, .hw_params = evm_hw_params, };

+ +static struct snd_soc_ops evm_tda998x_ops = { + .startup = evm_tda998x_startup, + .shutdown = evm_shutdown, + .hw_params = evm_tda998x_hw_params, +}; + /* davinci-evm machine dapm widgets */ static const struct snd_soc_dapm_widget aic3x_dapm_widgets[] = { SND_SOC_DAPM_HP("Headphone Jack", NULL), @@ -149,6 +184,35 @@ static int evm_aic3x_init(struct snd_soc_pcm_runtime *rtd) return 0; }

+static const struct snd_soc_dapm_widget tda998x_dapm_widgets[] = { + SND_SOC_DAPM_OUTPUT("HDMI Out"), +}; + +static int evm_tda998x_init(struct snd_soc_pcm_runtime *rtd) +{ + struct snd_soc_dai *cpu_dai = rtd->cpu_dai; + struct snd_soc_dapm_context *dapm = &rtd->codec->dapm; + struct snd_soc_card *soc_card = rtd->card; + int ret; + + ret = snd_soc_dai_set_clkdiv(cpu_dai, 0, 1); + if (ret < 0) + return ret; + + snd_soc_dapm_new_controls(dapm, tda998x_dapm_widgets, + ARRAY_SIZE(tda998x_dapm_widgets)); + + ret = snd_soc_of_parse_audio_routing(soc_card, "ti,audio-routing"); + + /* not connected */ + snd_soc_dapm_disable_pin(dapm, "RX"); + + /* always connected */ + snd_soc_dapm_enable_pin(dapm, "HDMI Out"); + + return 0; +} + /* davinci-evm digital audio interface glue - connects codec <--> CPU */ static struct snd_soc_dai_link dm6446_evm_dai = { .name = "TLV320AIC3X", @@ -334,7 +398,7 @@ static struct snd_soc_card da850_snd_soc_card = { #if defined(CONFIG_OF)

/* - * The struct is used as place holder. It will be completely + * The structs are used as place holders. They will be completely * filled with data from dt node. */ static struct snd_soc_dai_link evm_dai_tlv320aic3x = { @@ -347,10 +411,24 @@ static struct snd_soc_dai_link evm_dai_tlv320aic3x = { SND_SOC_DAIFMT_IB_NF, };

+static struct snd_soc_dai_link evm_dai_tda998x_hdmi = { + .name = "NXP TDA998x HDMI Chip", + .stream_name = "HDMI", + .codec_dai_name = "hdmi-hifi", + .ops = &evm_tda998x_ops, + .init = evm_tda998x_init, + .dai_fmt = (SND_SOC_DAIFMT_CBS_CFS | SND_SOC_DAIFMT_I2S | + SND_SOC_DAIFMT_IB_NF), +}; + static const struct of_device_id davinci_evm_dt_ids[] = { { .compatible = "ti,da830-evm-audio", - .data = (void *) &evm_dai_tlv320aic3x, + .data = &evm_dai_tlv320aic3x, + }, + { + .compatible = "ti,am335x-beaglebone-black-audio", + .data = &evm_dai_tda998x_hdmi, }, { /* sentinel */ } };

Add external clock provaider for am33xx devices.

Signed-off-by: Jyri Sarha jsarha@ti.com --- arch/arm/boot/dts/am33xx.dtsi | 10 ++++++++++ 1 file changed, 10 insertions(+)

diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi index 4a4e02d..5093c64 100644 --- a/arch/arm/boot/dts/am33xx.dtsi +++ b/arch/arm/boot/dts/am33xx.dtsi @@ -92,6 +92,16 @@ pinctrl-single,function-mask = <0x7f>; };

+ ext_clocks { + compatible = "ti,external-clocks"; + + ext_clocks: clocks { + }; + + ext_clockdomains: clockdomains { + }; + }; + /* * XXX: Use a flat representation of the AM33XX interconnect. * The real AM33XX interconnect network is quite complex. Since

Adds mcasp0_pins, clk_mcasp0_fixed, clk_mcasp0, mcasp0, hdmi_audio, and sound nodes.

Signed-off-by: Jyri Sarha jsarha@ti.com --- arch/arm/boot/dts/am335x-boneblack.dts | 54 ++++++++++++++++++++++++++++++++ 1 file changed, 54 insertions(+)

diff --git a/arch/arm/boot/dts/am335x-boneblack.dts b/arch/arm/boot/dts/am335x-boneblack.dts index 305975d..c3c4618 100644 --- a/arch/arm/boot/dts/am335x-boneblack.dts +++ b/arch/arm/boot/dts/am335x-boneblack.dts @@ -59,12 +59,50 @@ 0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 | AM33XX_PIN_OUTPUT */ >; }; + + mcasp0_pins: mcasp0_pins { + pinctrl-single,pins = < + 0x1ac (PIN_INPUT_PULLUP | MUX_MODE0) /* mcasp0_ahclkx.mcasp0_ahclkx */ + 0x19c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mcasp0_ahclkr.mcasp0_axr2 */ + 0x194 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mcasp0_fsx.mcasp0_fsx */ + 0x190 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp0_aclkx.mcasp0_aclkx */ + 0x06c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a11.GPIO1_27 */ + >; + }; };

&lcdc { status = "okay"; };

+&mcasp0 { + pinctrl-names = "default"; + pinctrl-0 = <&mcasp0_pins>; + status = "okay"; + op-mode = <0>; /* MCASP_IIS_MODE */ + tdm-slots = <2>; + serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */ + 0 0 1 0 + >; + tx-num-evt = <1>; + rx-num-evt = <1>; +}; + +&ext_clocks { + clk_mcasp0_fixed: clk_mcasp0_fixed { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <24576000>; + }; + + clk_mcasp0: clk_mcasp0 { + #clock-cells = <0>; + compatible = "gpio-clock"; + clocks = <&clk_mcasp0_fixed>; + enable-gpios = <&gpio1 27 0>; /* BeagleBone Black Clk enable on GPIO1_27 */ + }; +}; + / { hdmi { compatible = "ti,tilcdc,slave"; @@ -74,4 +112,20 @@ pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>; status = "okay"; }; + + hdmi_audio: hdmi_audio@0 { + compatible = "linux,hdmi-audio"; + status = "okay"; + }; + + sound { + compatible = "ti,am335x-beaglebone-black-audio"; + ti,model = "TI BeagleBone Black"; + ti,audio-codec = <&hdmi_audio>; + ti,mcasp-controller = <&mcasp0>; + ti,audio-routing = + "HDMI Out", "TX"; + clocks = <&clk_mcasp0>; + clock-names = "mclk"; + }; };

Select CONFIG_SND_EDMA_SOC=m and CONFIG_SND_AM335X_SOC_NXPTDA_EVM=m for BBB HDMI audio.

Signed-off-by: Jyri Sarha jsarha@ti.com --- arch/arm/configs/omap2plus_defconfig | 2 ++ 1 file changed, 2 insertions(+)

diff --git a/arch/arm/configs/omap2plus_defconfig b/arch/arm/configs/omap2plus_defconfig index 8b07fda..73dbfad 100644 --- a/arch/arm/configs/omap2plus_defconfig +++ b/arch/arm/configs/omap2plus_defconfig @@ -222,7 +222,9 @@ CONFIG_SND_DEBUG=y CONFIG_SND_USB_AUDIO=m CONFIG_SND_SOC=m CONFIG_SND_OMAP_SOC=m +CONFIG_SND_EDMA_SOC=m CONFIG_SND_AM33XX_SOC_EVM=m +CONFIG_SND_AM335X_SOC_NXPTDA_EVM=m CONFIG_SND_DAVINCI_SOC=m CONFIG_SND_OMAP_SOC_OMAP_TWL4030=m CONFIG_SND_OMAP_SOC_OMAP_ABE_TWL6040=m