Add the 10nm DSI PHY/PLL drivers. This will be used on the SDM845 SoC. Most of the code is based on the corresponding downstream PLL [1] and PHY [2] drivers.
The PHY driver has a few TODOs which would be resolved in future patches.
[1] https://source.codeaurora.org/quic/la/kernel/msm-4.9/tree/drivers/clk/qcom/m... [2] https://source.codeaurora.org/quic/la/kernel/msm-4.9/tree/drivers/gpu/drm/ms...
Archit Taneja (4): drm/msm/dsi: Update generated headers for 10nm PLL/PHY drm/msm/dsi: Add skeleton 10nm PHY/PLL code drm/msm/dsi: Populate PLL 10nm clock ops drm/msm/dsi: Populate the 10nm PHY funcs
drivers/gpu/drm/msm/Kconfig | 7 + drivers/gpu/drm/msm/Makefile | 2 + drivers/gpu/drm/msm/dsi/dsi.h | 1 + drivers/gpu/drm/msm/dsi/dsi.xml.h | 187 ++++++- drivers/gpu/drm/msm/dsi/phy/dsi_phy.c | 4 + drivers/gpu/drm/msm/dsi/phy/dsi_phy.h | 1 + drivers/gpu/drm/msm/dsi/phy/dsi_phy_10nm.c | 251 +++++++++ drivers/gpu/drm/msm/dsi/pll/dsi_pll.c | 3 + drivers/gpu/drm/msm/dsi/pll/dsi_pll.h | 9 + drivers/gpu/drm/msm/dsi/pll/dsi_pll_10nm.c | 822 +++++++++++++++++++++++++++++ 10 files changed, 1274 insertions(+), 13 deletions(-) create mode 100644 drivers/gpu/drm/msm/dsi/phy/dsi_phy_10nm.c create mode 100644 drivers/gpu/drm/msm/dsi/pll/dsi_pll_10nm.c
Signed-off-by: Archit Taneja architt@codeaurora.org --- drivers/gpu/drm/msm/dsi/dsi.xml.h | 187 +++++++++++++++++++++++++++++++++++--- 1 file changed, 174 insertions(+), 13 deletions(-)
diff --git a/drivers/gpu/drm/msm/dsi/dsi.xml.h b/drivers/gpu/drm/msm/dsi/dsi.xml.h index 479086ccf180..f6a9471b70c8 100644 --- a/drivers/gpu/drm/msm/dsi/dsi.xml.h +++ b/drivers/gpu/drm/msm/dsi/dsi.xml.h @@ -8,19 +8,10 @@ This file was generated by the rules-ng-ng headergen tool in this git repository git clone https://github.com/freedreno/envytools.git
The rules-ng-ng source files this header was generated from are: -- /home/robclark/src/freedreno/envytools/rnndb/msm.xml ( 676 bytes, from 2017-05-17 13:21:27) -- /home/robclark/src/freedreno/envytools/rnndb/freedreno_copyright.xml ( 1572 bytes, from 2017-05-17 13:21:27) -- /home/robclark/src/freedreno/envytools/rnndb/mdp/mdp4.xml ( 20915 bytes, from 2017-05-17 13:21:27) -- /home/robclark/src/freedreno/envytools/rnndb/mdp/mdp_common.xml ( 2849 bytes, from 2017-05-17 13:21:27) -- /home/robclark/src/freedreno/envytools/rnndb/mdp/mdp5.xml ( 37411 bytes, from 2017-05-17 13:21:27) -- /home/robclark/src/freedreno/envytools/rnndb/dsi/dsi.xml ( 33004 bytes, from 2017-05-17 13:21:27) -- /home/robclark/src/freedreno/envytools/rnndb/dsi/sfpb.xml ( 602 bytes, from 2017-05-17 13:21:27) -- /home/robclark/src/freedreno/envytools/rnndb/dsi/mmss_cc.xml ( 1686 bytes, from 2017-05-17 13:21:27) -- /home/robclark/src/freedreno/envytools/rnndb/hdmi/qfprom.xml ( 600 bytes, from 2017-05-17 13:21:27) -- /home/robclark/src/freedreno/envytools/rnndb/hdmi/hdmi.xml ( 41799 bytes, from 2017-06-16 12:32:42) -- /home/robclark/src/freedreno/envytools/rnndb/edp/edp.xml ( 10416 bytes, from 2017-05-17 13:21:27) - -Copyright (C) 2013-2017 by the following authors: +- /local/mnt/workspace/source_trees/envytools/rnndb/../rnndb/dsi/dsi.xml ( 37239 bytes, from 2018-01-12 09:09:22) +- /local/mnt/workspace/source_trees/envytools/rnndb/freedreno_copyright.xml ( 1572 bytes, from 2016-05-09 06:32:54) + +Copyright (C) 2013-2018 by the following authors: - Rob Clark robdclark@gmail.com (robclark) - Ilia Mirkin imirkin@alum.mit.edu (imirkin)
@@ -1556,5 +1547,175 @@ static inline uint32_t REG_DSI_14nm_PHY_LN_VREG_CNTRL(uint32_t i0) { return 0x00
#define REG_DSI_14nm_PHY_PLL_PLL_BANDGAP 0x00000108
+#define REG_DSI_10nm_PHY_CMN_REVISION_ID0 0x00000000 + +#define REG_DSI_10nm_PHY_CMN_REVISION_ID1 0x00000004 + +#define REG_DSI_10nm_PHY_CMN_REVISION_ID2 0x00000008 + +#define REG_DSI_10nm_PHY_CMN_REVISION_ID3 0x0000000c + +#define REG_DSI_10nm_PHY_CMN_CLK_CFG0 0x00000010 + +#define REG_DSI_10nm_PHY_CMN_CLK_CFG1 0x00000014 + +#define REG_DSI_10nm_PHY_CMN_GLBL_CTRL 0x00000018 + +#define REG_DSI_10nm_PHY_CMN_RBUF_CTRL 0x0000001c + +#define REG_DSI_10nm_PHY_CMN_VREG_CTRL 0x00000020 + +#define REG_DSI_10nm_PHY_CMN_CTRL_0 0x00000024 + +#define REG_DSI_10nm_PHY_CMN_CTRL_1 0x00000028 + +#define REG_DSI_10nm_PHY_CMN_CTRL_2 0x0000002c + +#define REG_DSI_10nm_PHY_CMN_LANE_CFG0 0x00000030 + +#define REG_DSI_10nm_PHY_CMN_LANE_CFG1 0x00000034 + +#define REG_DSI_10nm_PHY_CMN_PLL_CNTRL 0x00000038 + +#define REG_DSI_10nm_PHY_CMN_LANE_CTRL0 0x00000098 + +#define REG_DSI_10nm_PHY_CMN_LANE_CTRL1 0x0000009c + +#define REG_DSI_10nm_PHY_CMN_LANE_CTRL2 0x000000a0 + +#define REG_DSI_10nm_PHY_CMN_LANE_CTRL3 0x000000a4 + +#define REG_DSI_10nm_PHY_CMN_LANE_CTRL4 0x000000a8 + +#define REG_DSI_10nm_PHY_CMN_TIMING_CTRL_0 0x000000ac + +#define REG_DSI_10nm_PHY_CMN_TIMING_CTRL_1 0x000000b0 + +#define REG_DSI_10nm_PHY_CMN_TIMING_CTRL_2 0x000000b4 + +#define REG_DSI_10nm_PHY_CMN_TIMING_CTRL_3 0x000000b8 + +#define REG_DSI_10nm_PHY_CMN_TIMING_CTRL_4 0x000000bc + +#define REG_DSI_10nm_PHY_CMN_TIMING_CTRL_5 0x000000c0 + +#define REG_DSI_10nm_PHY_CMN_TIMING_CTRL_6 0x000000c4 + +#define REG_DSI_10nm_PHY_CMN_TIMING_CTRL_7 0x000000c8 + +#define REG_DSI_10nm_PHY_CMN_TIMING_CTRL_8 0x000000cc + +#define REG_DSI_10nm_PHY_CMN_TIMING_CTRL_9 0x000000d0 + +#define REG_DSI_10nm_PHY_CMN_TIMING_CTRL_10 0x000000d4 + +#define REG_DSI_10nm_PHY_CMN_TIMING_CTRL_11 0x000000d8 + +#define REG_DSI_10nm_PHY_CMN_PHY_STATUS 0x000000ec + +#define REG_DSI_10nm_PHY_CMN_LANE_STATUS0 0x000000f4 + +#define REG_DSI_10nm_PHY_CMN_LANE_STATUS1 0x000000f8 + +static inline uint32_t REG_DSI_10nm_PHY_LN(uint32_t i0) { return 0x00000000 + 0x80*i0; } + +static inline uint32_t REG_DSI_10nm_PHY_LN_CFG0(uint32_t i0) { return 0x00000000 + 0x80*i0; } + +static inline uint32_t REG_DSI_10nm_PHY_LN_CFG1(uint32_t i0) { return 0x00000004 + 0x80*i0; } + +static inline uint32_t REG_DSI_10nm_PHY_LN_CFG2(uint32_t i0) { return 0x00000008 + 0x80*i0; } + +static inline uint32_t REG_DSI_10nm_PHY_LN_CFG3(uint32_t i0) { return 0x0000000c + 0x80*i0; } + +static inline uint32_t REG_DSI_10nm_PHY_LN_TEST_DATAPATH(uint32_t i0) { return 0x00000010 + 0x80*i0; } + +static inline uint32_t REG_DSI_10nm_PHY_LN_PIN_SWAP(uint32_t i0) { return 0x00000014 + 0x80*i0; } + +static inline uint32_t REG_DSI_10nm_PHY_LN_HSTX_STR_CTRL(uint32_t i0) { return 0x00000018 + 0x80*i0; } + +static inline uint32_t REG_DSI_10nm_PHY_LN_OFFSET_TOP_CTRL(uint32_t i0) { return 0x0000001c + 0x80*i0; } + +static inline uint32_t REG_DSI_10nm_PHY_LN_OFFSET_BOT_CTRL(uint32_t i0) { return 0x00000020 + 0x80*i0; } + +static inline uint32_t REG_DSI_10nm_PHY_LN_LPTX_STR_CTRL(uint32_t i0) { return 0x00000024 + 0x80*i0; } + +static inline uint32_t REG_DSI_10nm_PHY_LN_LPRX_CTRL(uint32_t i0) { return 0x00000028 + 0x80*i0; } + +static inline uint32_t REG_DSI_10nm_PHY_LN_TX_DCTRL(uint32_t i0) { return 0x0000002c + 0x80*i0; } + +#define REG_DSI_10nm_PHY_PLL_ANALOG_CONTROLS_ONE 0x00000000 + +#define REG_DSI_10nm_PHY_PLL_ANALOG_CONTROLS_TWO 0x00000004 + +#define REG_DSI_10nm_PHY_PLL_ANALOG_CONTROLS_THREE 0x00000010 + +#define REG_DSI_10nm_PHY_PLL_DSM_DIVIDER 0x0000001c + +#define REG_DSI_10nm_PHY_PLL_FEEDBACK_DIVIDER 0x00000020 + +#define REG_DSI_10nm_PHY_PLL_SYSTEM_MUXES 0x00000024 + +#define REG_DSI_10nm_PHY_PLL_CMODE 0x0000002c + +#define REG_DSI_10nm_PHY_PLL_CALIBRATION_SETTINGS 0x00000030 + +#define REG_DSI_10nm_PHY_PLL_BAND_SEL_CAL_SETTINGS_THREE 0x00000054 + +#define REG_DSI_10nm_PHY_PLL_FREQ_DETECT_SETTINGS_ONE 0x00000064 + +#define REG_DSI_10nm_PHY_PLL_PFILT 0x0000007c + +#define REG_DSI_10nm_PHY_PLL_IFILT 0x00000080 + +#define REG_DSI_10nm_PHY_PLL_OUTDIV 0x00000094 + +#define REG_DSI_10nm_PHY_PLL_CORE_OVERRIDE 0x000000a4 + +#define REG_DSI_10nm_PHY_PLL_CORE_INPUT_OVERRIDE 0x000000a8 + +#define REG_DSI_10nm_PHY_PLL_PLL_DIGITAL_TIMERS_TWO 0x000000b4 + +#define REG_DSI_10nm_PHY_PLL_DECIMAL_DIV_START_1 0x000000cc + +#define REG_DSI_10nm_PHY_PLL_FRAC_DIV_START_LOW_1 0x000000d0 + +#define REG_DSI_10nm_PHY_PLL_FRAC_DIV_START_MID_1 0x000000d4 + +#define REG_DSI_10nm_PHY_PLL_FRAC_DIV_START_HIGH_1 0x000000d8 + +#define REG_DSI_10nm_PHY_PLL_SSC_STEPSIZE_LOW_1 0x0000010c + +#define REG_DSI_10nm_PHY_PLL_SSC_STEPSIZE_HIGH_1 0x00000110 + +#define REG_DSI_10nm_PHY_PLL_SSC_DIV_PER_LOW_1 0x00000114 + +#define REG_DSI_10nm_PHY_PLL_SSC_DIV_PER_HIGH_1 0x00000118 + +#define REG_DSI_10nm_PHY_PLL_SSC_DIV_ADJPER_LOW_1 0x0000011c + +#define REG_DSI_10nm_PHY_PLL_SSC_DIV_ADJPER_HIGH_1 0x00000120 + +#define REG_DSI_10nm_PHY_PLL_SSC_CONTROL 0x0000013c + +#define REG_DSI_10nm_PHY_PLL_PLL_OUTDIV_RATE 0x00000140 + +#define REG_DSI_10nm_PHY_PLL_PLL_LOCKDET_RATE_1 0x00000144 + +#define REG_DSI_10nm_PHY_PLL_PLL_PROP_GAIN_RATE_1 0x0000014c + +#define REG_DSI_10nm_PHY_PLL_PLL_BAND_SET_RATE_1 0x00000154 + +#define REG_DSI_10nm_PHY_PLL_PLL_INT_GAIN_IFILT_BAND_1 0x0000015c + +#define REG_DSI_10nm_PHY_PLL_PLL_FL_INT_GAIN_PFILT_BAND_1 0x00000164 + +#define REG_DSI_10nm_PHY_PLL_PLL_LOCK_OVERRIDE 0x00000180 + +#define REG_DSI_10nm_PHY_PLL_PLL_LOCK_DELAY 0x00000184 + +#define REG_DSI_10nm_PHY_PLL_CLOCK_INVERTERS 0x0000018c + +#define REG_DSI_10nm_PHY_PLL_COMMON_STATUS_ONE 0x000001a0 +
#endif /* DSI_XML */
Add new 10nm DSI PLL/PHY files that will be used on SDM845.
Just populate empty pll/phy funcs for now. These will be filled up later.
Signed-off-by: Archit Taneja architt@codeaurora.org --- drivers/gpu/drm/msm/Kconfig | 7 ++ drivers/gpu/drm/msm/Makefile | 2 + drivers/gpu/drm/msm/dsi/dsi.h | 1 + drivers/gpu/drm/msm/dsi/phy/dsi_phy.c | 4 + drivers/gpu/drm/msm/dsi/phy/dsi_phy.h | 1 + drivers/gpu/drm/msm/dsi/phy/dsi_phy_10nm.c | 52 +++++++++ drivers/gpu/drm/msm/dsi/pll/dsi_pll.c | 3 + drivers/gpu/drm/msm/dsi/pll/dsi_pll.h | 9 ++ drivers/gpu/drm/msm/dsi/pll/dsi_pll_10nm.c | 176 +++++++++++++++++++++++++++++ 9 files changed, 255 insertions(+) create mode 100644 drivers/gpu/drm/msm/dsi/phy/dsi_phy_10nm.c create mode 100644 drivers/gpu/drm/msm/dsi/pll/dsi_pll_10nm.c
diff --git a/drivers/gpu/drm/msm/Kconfig b/drivers/gpu/drm/msm/Kconfig index 99d39b2aefa6..9ebaa7391113 100644 --- a/drivers/gpu/drm/msm/Kconfig +++ b/drivers/gpu/drm/msm/Kconfig @@ -81,3 +81,10 @@ config DRM_MSM_DSI_14NM_PHY default y help Choose this option if DSI PHY on 8996 is used on the platform. + +config DRM_MSM_DSI_10NM_PHY + bool "Enable DSI 10nm PHY driver in MSM DRM (used by SDM845)" + depends on DRM_MSM_DSI + default y + help + Choose this option if DSI PHY on SDM845 is used on the platform. diff --git a/drivers/gpu/drm/msm/Makefile b/drivers/gpu/drm/msm/Makefile index 92b3844202d2..14edd244df87 100644 --- a/drivers/gpu/drm/msm/Makefile +++ b/drivers/gpu/drm/msm/Makefile @@ -81,12 +81,14 @@ msm-$(CONFIG_DRM_MSM_DSI_28NM_PHY) += dsi/phy/dsi_phy_28nm.o msm-$(CONFIG_DRM_MSM_DSI_20NM_PHY) += dsi/phy/dsi_phy_20nm.o msm-$(CONFIG_DRM_MSM_DSI_28NM_8960_PHY) += dsi/phy/dsi_phy_28nm_8960.o msm-$(CONFIG_DRM_MSM_DSI_14NM_PHY) += dsi/phy/dsi_phy_14nm.o +msm-$(CONFIG_DRM_MSM_DSI_10NM_PHY) += dsi/phy/dsi_phy_10nm.o
ifeq ($(CONFIG_DRM_MSM_DSI_PLL),y) msm-y += dsi/pll/dsi_pll.o msm-$(CONFIG_DRM_MSM_DSI_28NM_PHY) += dsi/pll/dsi_pll_28nm.o msm-$(CONFIG_DRM_MSM_DSI_28NM_8960_PHY) += dsi/pll/dsi_pll_28nm_8960.o msm-$(CONFIG_DRM_MSM_DSI_14NM_PHY) += dsi/pll/dsi_pll_14nm.o +msm-$(CONFIG_DRM_MSM_DSI_10NM_PHY) += dsi/pll/dsi_pll_10nm.o endif
obj-$(CONFIG_DRM_MSM) += msm.o diff --git a/drivers/gpu/drm/msm/dsi/dsi.h b/drivers/gpu/drm/msm/dsi/dsi.h index eafd714a5b84..024e7a3af9f1 100644 --- a/drivers/gpu/drm/msm/dsi/dsi.h +++ b/drivers/gpu/drm/msm/dsi/dsi.h @@ -36,6 +36,7 @@ enum msm_dsi_phy_type { MSM_DSI_PHY_20NM, MSM_DSI_PHY_28NM_8960, MSM_DSI_PHY_14NM, + MSM_DSI_PHY_10NM, MSM_DSI_PHY_MAX };
diff --git a/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c b/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c index 790ca280cbfd..f8056d1df9a0 100644 --- a/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c +++ b/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c @@ -394,6 +394,10 @@ static const struct of_device_id dsi_phy_dt_match[] = { #ifdef CONFIG_DRM_MSM_DSI_14NM_PHY { .compatible = "qcom,dsi-phy-14nm", .data = &dsi_phy_14nm_cfgs }, +#endif +#ifdef CONFIG_DRM_MSM_DSI_10NM_PHY + { .compatible = "qcom,dsi-phy-10nm", + .data = &dsi_phy_10nm_cfgs }, #endif {} }; diff --git a/drivers/gpu/drm/msm/dsi/phy/dsi_phy.h b/drivers/gpu/drm/msm/dsi/phy/dsi_phy.h index 1733f6608a09..c56268cbdb3d 100644 --- a/drivers/gpu/drm/msm/dsi/phy/dsi_phy.h +++ b/drivers/gpu/drm/msm/dsi/phy/dsi_phy.h @@ -48,6 +48,7 @@ extern const struct msm_dsi_phy_cfg dsi_phy_28nm_lp_cfgs; extern const struct msm_dsi_phy_cfg dsi_phy_20nm_cfgs; extern const struct msm_dsi_phy_cfg dsi_phy_28nm_8960_cfgs; extern const struct msm_dsi_phy_cfg dsi_phy_14nm_cfgs; +extern const struct msm_dsi_phy_cfg dsi_phy_10nm_cfgs;
struct msm_dsi_dphy_timing { u32 clk_pre; diff --git a/drivers/gpu/drm/msm/dsi/phy/dsi_phy_10nm.c b/drivers/gpu/drm/msm/dsi/phy/dsi_phy_10nm.c new file mode 100644 index 000000000000..b7545fb63bf5 --- /dev/null +++ b/drivers/gpu/drm/msm/dsi/phy/dsi_phy_10nm.c @@ -0,0 +1,52 @@ +/* + * SPDX-License-Identifier: GPL-2.0 + * Copyright (c) 2018, The Linux Foundation + */ + +#include <linux/iopoll.h> + +#include "dsi_phy.h" +#include "dsi.xml.h" + +static int dsi_10nm_phy_enable(struct msm_dsi_phy *phy, int src_pll_id, + struct msm_dsi_phy_clk_request *clk_req) +{ + return 0; +} + +static void dsi_10nm_phy_disable(struct msm_dsi_phy *phy) +{ +} + +static int dsi_10nm_phy_init(struct msm_dsi_phy *phy) +{ + struct platform_device *pdev = phy->pdev; + + phy->lane_base = msm_ioremap(pdev, "dsi_phy_lane", + "DSI_PHY_LANE"); + if (IS_ERR(phy->lane_base)) { + dev_err(&pdev->dev, "%s: failed to map phy lane base\n", + __func__); + return -ENOMEM; + } + + return 0; +} + +const struct msm_dsi_phy_cfg dsi_phy_10nm_cfgs = { + .type = MSM_DSI_PHY_10NM, + .src_pll_truthtable = { {false, false}, {true, false} }, + .reg_cfg = { + .num = 1, + .regs = { + {"vdds", 36000, 32}, + }, + }, + .ops = { + .enable = dsi_10nm_phy_enable, + .disable = dsi_10nm_phy_disable, + .init = dsi_10nm_phy_init, + }, + .io_start = { 0xae94400, 0xae96400 }, + .num_dsi_phy = 2, +}; diff --git a/drivers/gpu/drm/msm/dsi/pll/dsi_pll.c b/drivers/gpu/drm/msm/dsi/pll/dsi_pll.c index bc289f5c9078..1ab5a49385d6 100644 --- a/drivers/gpu/drm/msm/dsi/pll/dsi_pll.c +++ b/drivers/gpu/drm/msm/dsi/pll/dsi_pll.c @@ -166,6 +166,9 @@ struct msm_dsi_pll *msm_dsi_pll_init(struct platform_device *pdev, case MSM_DSI_PHY_14NM: pll = msm_dsi_pll_14nm_init(pdev, id); break; + case MSM_DSI_PHY_10NM: + pll = msm_dsi_pll_10nm_init(pdev, id); + break; default: pll = ERR_PTR(-ENXIO); break; diff --git a/drivers/gpu/drm/msm/dsi/pll/dsi_pll.h b/drivers/gpu/drm/msm/dsi/pll/dsi_pll.h index f63e7ada74a8..8b32271cbc24 100644 --- a/drivers/gpu/drm/msm/dsi/pll/dsi_pll.h +++ b/drivers/gpu/drm/msm/dsi/pll/dsi_pll.h @@ -115,5 +115,14 @@ msm_dsi_pll_14nm_init(struct platform_device *pdev, int id) return ERR_PTR(-ENODEV); } #endif +#ifdef CONFIG_DRM_MSM_DSI_10NM_PHY +struct msm_dsi_pll *msm_dsi_pll_10nm_init(struct platform_device *pdev, int id); +#else +static inline struct msm_dsi_pll * +msm_dsi_pll_10nm_init(struct platform_device *pdev, int id) +{ + return ERR_PTR(-ENODEV); +} +#endif #endif /* __DSI_PLL_H__ */
diff --git a/drivers/gpu/drm/msm/dsi/pll/dsi_pll_10nm.c b/drivers/gpu/drm/msm/dsi/pll/dsi_pll_10nm.c new file mode 100644 index 000000000000..34c24442d34b --- /dev/null +++ b/drivers/gpu/drm/msm/dsi/pll/dsi_pll_10nm.c @@ -0,0 +1,176 @@ +/* + * SPDX-License-Identifier: GPL-2.0 + * Copyright (c) 2018, The Linux Foundation + */ + +#include <linux/clk.h> +#include <linux/clk-provider.h> +#include <linux/iopoll.h> + +#include "dsi_pll.h" +#include "dsi.xml.h" + +struct dsi_pll_10nm { + struct msm_dsi_pll base; + + int id; + struct platform_device *pdev; + + void __iomem *phy_cmn_mmio; + void __iomem *mmio; + + int vco_delay; + + enum msm_dsi_phy_usecase uc; + struct dsi_pll_10nm *slave; +}; + +#define to_pll_10nm(x) container_of(x, struct dsi_pll_10nm, base) + +/* + * Global list of private DSI PLL struct pointers. We need this for Dual DSI + * mode, where the master PLL's clk_ops needs access the slave's private data + */ +static struct dsi_pll_10nm *pll_10nm_list[DSI_MAX]; + +static int dsi_pll_10nm_vco_set_rate(struct clk_hw *hw, unsigned long rate, + unsigned long parent_rate) +{ + struct msm_dsi_pll *pll = hw_clk_to_pll(hw); + struct dsi_pll_10nm *pll_10nm = to_pll_10nm(pll); + + DBG("DSI PLL%d rate=%lu, parent's=%lu", pll_10nm->id, rate, + parent_rate); + + return 0; +} + +static unsigned long dsi_pll_10nm_vco_recalc_rate(struct clk_hw *hw, + unsigned long parent_rate) +{ + struct msm_dsi_pll *pll = hw_clk_to_pll(hw); + struct dsi_pll_10nm *pll_10nm = to_pll_10nm(pll); + u64 vco_rate = 0x0; + + DBG("DSI PLL%d returning vco rate = %lu", pll_10nm->id, + (unsigned long)vco_rate); + + return (unsigned long)vco_rate; +} + +static const struct clk_ops clk_ops_dsi_pll_10nm_vco = { + .round_rate = msm_dsi_pll_helper_clk_round_rate, + .set_rate = dsi_pll_10nm_vco_set_rate, + .recalc_rate = dsi_pll_10nm_vco_recalc_rate, + .prepare = msm_dsi_pll_helper_clk_prepare, + .unprepare = msm_dsi_pll_helper_clk_unprepare, +}; + +/* + * PLL Callbacks + */ + +static void dsi_pll_10nm_save_state(struct msm_dsi_pll *pll) +{ + struct dsi_pll_10nm *pll_10nm = to_pll_10nm(pll); + + DBG("DSI PLL%d", pll_10nm->id); +} + +static int dsi_pll_10nm_restore_state(struct msm_dsi_pll *pll) +{ + struct dsi_pll_10nm *pll_10nm = to_pll_10nm(pll); + + DBG("DSI PLL%d", pll_10nm->id); + + return 0; +} + +static int dsi_pll_10nm_set_usecase(struct msm_dsi_pll *pll, + enum msm_dsi_phy_usecase uc) +{ + struct dsi_pll_10nm *pll_10nm = to_pll_10nm(pll); + + DBG("DSI PLL%d", pll_10nm->id); + + return 0; +} + +static int dsi_pll_10nm_get_provider(struct msm_dsi_pll *pll, + struct clk **byte_clk_provider, + struct clk **pixel_clk_provider) +{ + struct dsi_pll_10nm *pll_10nm = to_pll_10nm(pll); + + DBG("DSI PLL%d", pll_10nm->id); + + if (byte_clk_provider) + *byte_clk_provider = NULL; + if (pixel_clk_provider) + *pixel_clk_provider = NULL; + + return 0; +} + +static void dsi_pll_10nm_destroy(struct msm_dsi_pll *pll) +{ + struct dsi_pll_10nm *pll_10nm = to_pll_10nm(pll); + + DBG("DSI PLL%d", pll_10nm->id); +} + +static int pll_10nm_register(struct dsi_pll_10nm *pll_10nm) +{ + return 0; +} + +struct msm_dsi_pll *msm_dsi_pll_10nm_init(struct platform_device *pdev, int id) +{ + struct dsi_pll_10nm *pll_10nm; + struct msm_dsi_pll *pll; + int ret; + + if (!pdev) + return ERR_PTR(-ENODEV); + + pll_10nm = devm_kzalloc(&pdev->dev, sizeof(*pll_10nm), GFP_KERNEL); + if (!pll_10nm) + return ERR_PTR(-ENOMEM); + + DBG("DSI PLL%d", id); + + pll_10nm->pdev = pdev; + pll_10nm->id = id; + pll_10nm_list[id] = pll_10nm; + + pll_10nm->phy_cmn_mmio = msm_ioremap(pdev, "dsi_phy", "DSI_PHY"); + if (IS_ERR_OR_NULL(pll_10nm->phy_cmn_mmio)) { + dev_err(&pdev->dev, "failed to map CMN PHY base\n"); + return ERR_PTR(-ENOMEM); + } + + pll_10nm->mmio = msm_ioremap(pdev, "dsi_pll", "DSI_PLL"); + if (IS_ERR_OR_NULL(pll_10nm->mmio)) { + dev_err(&pdev->dev, "failed to map PLL base\n"); + return ERR_PTR(-ENOMEM); + } + + pll = &pll_10nm->base; + pll->min_rate = 1000000000UL; + pll->max_rate = 3500000000UL; + pll->get_provider = dsi_pll_10nm_get_provider; + pll->destroy = dsi_pll_10nm_destroy; + pll->save_state = dsi_pll_10nm_save_state; + pll->restore_state = dsi_pll_10nm_restore_state; + pll->set_usecase = dsi_pll_10nm_set_usecase; + + pll_10nm->vco_delay = 1; + + ret = pll_10nm_register(pll_10nm); + if (ret) { + dev_err(&pdev->dev, "failed to register PLL: %d\n", ret); + return ERR_PTR(ret); + } + + return pll; +}
Populate PLL clock ops from downstream. This contains the VCO PLL ops and the registration of standard clk_divider and clk_mux clocks. Unlike 14nm PLL, the postdividers/mux of the slave PLL doesn't need to be set to the same values of the postdivs/mux of the master PLL. Hence, we don't need special postdivider clock ops like we did with the 14nm PLL driver.
Like the previous PLL drivers, the implementation is slightly different from downstream. We don't use shadow clocks, but have the ability to reparent the RCGs to a different source.
Signed-off-by: Archit Taneja architt@codeaurora.org --- drivers/gpu/drm/msm/dsi/pll/dsi_pll_10nm.c | 662 ++++++++++++++++++++++++++++- 1 file changed, 654 insertions(+), 8 deletions(-)
diff --git a/drivers/gpu/drm/msm/dsi/pll/dsi_pll_10nm.c b/drivers/gpu/drm/msm/dsi/pll/dsi_pll_10nm.c index 34c24442d34b..c4c37a7df637 100644 --- a/drivers/gpu/drm/msm/dsi/pll/dsi_pll_10nm.c +++ b/drivers/gpu/drm/msm/dsi/pll/dsi_pll_10nm.c @@ -10,6 +10,78 @@ #include "dsi_pll.h" #include "dsi.xml.h"
+/* + * DSI PLL 10nm - clock diagram (eg: DSI0): + * + * dsi0_pll_out_div_clk dsi0_pll_bit_clk + * | | + * | | + * +---------+ | +----------+ | +----+ + * dsi0vco_clk ---| out_div |--o--| divl_3_0 |--o--| /8 |-- dsi0pllbyte + * +---------+ | +----------+ | +----+ + * | | + * | | dsi0_pll_by_2_bit_clk + * | | | + * | | +----+ | |\ dsi0_pclk_mux + * | |--| /2 |--o--| \ | + * | | +----+ | \ | +---------+ + * | --------------| |--o--| div_7_4 |-- dsi0pll + * |------------------------------| / +---------+ + * | +-----+ | / + * -----------| /4? |--o----------|/ + * +-----+ | | + * | |dsiclk_sel + * | + * dsi0_pll_post_out_div_clk + */ + +#define DSI_BYTE_PLL_CLK 0 +#define DSI_PIXEL_PLL_CLK 1 +#define NUM_PROVIDED_CLKS 2 + +struct dsi_pll_regs { + u32 pll_prop_gain_rate; + u32 pll_lockdet_rate; + u32 decimal_div_start; + u32 frac_div_start_low; + u32 frac_div_start_mid; + u32 frac_div_start_high; + u32 pll_clock_inverters; + u32 ssc_stepsize_low; + u32 ssc_stepsize_high; + u32 ssc_div_per_low; + u32 ssc_div_per_high; + u32 ssc_adjper_low; + u32 ssc_adjper_high; + u32 ssc_control; +}; + +struct dsi_pll_config { + u32 ref_freq; + bool div_override; + u32 output_div; + bool ignore_frac; + bool disable_prescaler; + bool enable_ssc; + bool ssc_center; + u32 dec_bits; + u32 frac_bits; + u32 lock_timer; + u32 ssc_freq; + u32 ssc_offset; + u32 ssc_adj_per; + u32 thresh_cycles; + u32 refclk_cycles; +}; + +struct pll_10nm_cached_state { + unsigned long vco_rate; + u8 bit_clk_div; + u8 pix_clk_div; + u8 pll_out_div; + u8 pll_mux; +}; + struct dsi_pll_10nm { struct msm_dsi_pll base;
@@ -19,7 +91,24 @@ struct dsi_pll_10nm { void __iomem *phy_cmn_mmio; void __iomem *mmio;
+ u64 vco_ref_clk_rate; + u64 vco_current_rate; + + /* protects REG_DSI_10nm_PHY_CMN_CLK_CFG0 register */ + spinlock_t postdiv_lock; + int vco_delay; + struct dsi_pll_config pll_configuration; + struct dsi_pll_regs reg_setup; + + /* private clocks: */ + struct clk_hw *hws[NUM_DSI_CLOCKS_MAX]; + u32 num_hws; + + /* clock-provider: */ + struct clk_hw_onecell_data *hw_data; + + struct pll_10nm_cached_state cached_state;
enum msm_dsi_phy_usecase uc; struct dsi_pll_10nm *slave; @@ -33,6 +122,190 @@ struct dsi_pll_10nm { */ static struct dsi_pll_10nm *pll_10nm_list[DSI_MAX];
+static void dsi_pll_setup_config(struct dsi_pll_10nm *pll) +{ + struct dsi_pll_config *config = &pll->pll_configuration; + + config->ref_freq = pll->vco_ref_clk_rate; + config->output_div = 1; + config->dec_bits = 8; + config->frac_bits = 18; + config->lock_timer = 64; + config->ssc_freq = 31500; + config->ssc_offset = 5000; + config->ssc_adj_per = 2; + config->thresh_cycles = 32; + config->refclk_cycles = 256; + + config->div_override = false; + config->ignore_frac = false; + config->disable_prescaler = false; + + config->enable_ssc = false; + config->ssc_center = 0; +} + +static void dsi_pll_calc_dec_frac(struct dsi_pll_10nm *pll) +{ + struct dsi_pll_config *config = &pll->pll_configuration; + struct dsi_pll_regs *regs = &pll->reg_setup; + u64 fref = pll->vco_ref_clk_rate; + u64 pll_freq; + u64 divider; + u64 dec, dec_multiple; + u32 frac; + u64 multiplier; + + pll_freq = pll->vco_current_rate; + + if (config->disable_prescaler) + divider = fref; + else + divider = fref * 2; + + multiplier = 1 << config->frac_bits; + dec_multiple = div_u64(pll_freq * multiplier, divider); + div_u64_rem(dec_multiple, multiplier, &frac); + + dec = div_u64(dec_multiple, multiplier); + + if (pll_freq <= 1900000000UL) + regs->pll_prop_gain_rate = 8; + else if (pll_freq <= 3000000000UL) + regs->pll_prop_gain_rate = 10; + else + regs->pll_prop_gain_rate = 12; + if (pll_freq < 1100000000UL) + regs->pll_clock_inverters = 8; + else + regs->pll_clock_inverters = 0; + + regs->pll_lockdet_rate = config->lock_timer; + regs->decimal_div_start = dec; + regs->frac_div_start_low = (frac & 0xff); + regs->frac_div_start_mid = (frac & 0xff00) >> 8; + regs->frac_div_start_high = (frac & 0x30000) >> 16; +} + +#define SSC_CENTER BIT(0) +#define SSC_EN BIT(1) + +static void dsi_pll_calc_ssc(struct dsi_pll_10nm *pll) +{ + struct dsi_pll_config *config = &pll->pll_configuration; + struct dsi_pll_regs *regs = &pll->reg_setup; + u32 ssc_per; + u32 ssc_mod; + u64 ssc_step_size; + u64 frac; + + if (!config->enable_ssc) { + DBG("SSC not enabled\n"); + return; + } + + ssc_per = DIV_ROUND_CLOSEST(config->ref_freq, config->ssc_freq) / 2 - 1; + ssc_mod = (ssc_per + 1) % (config->ssc_adj_per + 1); + ssc_per -= ssc_mod; + + frac = regs->frac_div_start_low | + (regs->frac_div_start_mid << 8) | + (regs->frac_div_start_high << 16); + ssc_step_size = regs->decimal_div_start; + ssc_step_size *= (1 << config->frac_bits); + ssc_step_size += frac; + ssc_step_size *= config->ssc_offset; + ssc_step_size *= (config->ssc_adj_per + 1); + ssc_step_size = div_u64(ssc_step_size, (ssc_per + 1)); + ssc_step_size = DIV_ROUND_CLOSEST_ULL(ssc_step_size, 1000000); + + regs->ssc_div_per_low = ssc_per & 0xFF; + regs->ssc_div_per_high = (ssc_per & 0xFF00) >> 8; + regs->ssc_stepsize_low = (u32)(ssc_step_size & 0xFF); + regs->ssc_stepsize_high = (u32)((ssc_step_size & 0xFF00) >> 8); + regs->ssc_adjper_low = config->ssc_adj_per & 0xFF; + regs->ssc_adjper_high = (config->ssc_adj_per & 0xFF00) >> 8; + + regs->ssc_control = config->ssc_center ? SSC_CENTER : 0; + + pr_debug("SCC: Dec:%d, frac:%llu, frac_bits:%d\n", + regs->decimal_div_start, frac, config->frac_bits); + pr_debug("SSC: div_per:0x%X, stepsize:0x%X, adjper:0x%X\n", + ssc_per, (u32)ssc_step_size, config->ssc_adj_per); +} + +static void dsi_pll_ssc_commit(struct dsi_pll_10nm *pll) +{ + void __iomem *base = pll->mmio; + struct dsi_pll_regs *regs = &pll->reg_setup; + + if (pll->pll_configuration.enable_ssc) { + pr_debug("SSC is enabled\n"); + + pll_write(base + REG_DSI_10nm_PHY_PLL_SSC_STEPSIZE_LOW_1, + regs->ssc_stepsize_low); + pll_write(base + REG_DSI_10nm_PHY_PLL_SSC_STEPSIZE_HIGH_1, + regs->ssc_stepsize_high); + pll_write(base + REG_DSI_10nm_PHY_PLL_SSC_DIV_PER_LOW_1, + regs->ssc_div_per_low); + pll_write(base + REG_DSI_10nm_PHY_PLL_SSC_DIV_PER_HIGH_1, + regs->ssc_div_per_high); + pll_write(base + REG_DSI_10nm_PHY_PLL_SSC_DIV_ADJPER_LOW_1, + regs->ssc_adjper_low); + pll_write(base + REG_DSI_10nm_PHY_PLL_SSC_DIV_ADJPER_HIGH_1, + regs->ssc_adjper_high); + pll_write(base + REG_DSI_10nm_PHY_PLL_SSC_CONTROL, + SSC_EN | regs->ssc_control); + } +} + +static void dsi_pll_config_hzindep_reg(struct dsi_pll_10nm *pll) +{ + void __iomem *base = pll->mmio; + + pll_write(base + REG_DSI_10nm_PHY_PLL_ANALOG_CONTROLS_ONE, 0x80); + pll_write(base + REG_DSI_10nm_PHY_PLL_ANALOG_CONTROLS_TWO, 0x03); + pll_write(base + REG_DSI_10nm_PHY_PLL_ANALOG_CONTROLS_THREE, 0x00); + pll_write(base + REG_DSI_10nm_PHY_PLL_DSM_DIVIDER, 0x00); + pll_write(base + REG_DSI_10nm_PHY_PLL_FEEDBACK_DIVIDER, 0x4e); + pll_write(base + REG_DSI_10nm_PHY_PLL_CALIBRATION_SETTINGS, 0x40); + pll_write(base + REG_DSI_10nm_PHY_PLL_BAND_SEL_CAL_SETTINGS_THREE, + 0xba); + pll_write(base + REG_DSI_10nm_PHY_PLL_FREQ_DETECT_SETTINGS_ONE, 0x0c); + pll_write(base + REG_DSI_10nm_PHY_PLL_OUTDIV, 0x00); + pll_write(base + REG_DSI_10nm_PHY_PLL_CORE_OVERRIDE, 0x00); + pll_write(base + REG_DSI_10nm_PHY_PLL_PLL_DIGITAL_TIMERS_TWO, 0x08); + pll_write(base + REG_DSI_10nm_PHY_PLL_PLL_PROP_GAIN_RATE_1, 0x08); + pll_write(base + REG_DSI_10nm_PHY_PLL_PLL_BAND_SET_RATE_1, 0xc0); + pll_write(base + REG_DSI_10nm_PHY_PLL_PLL_INT_GAIN_IFILT_BAND_1, 0xfa); + pll_write(base + REG_DSI_10nm_PHY_PLL_PLL_FL_INT_GAIN_PFILT_BAND_1, + 0x4c); + pll_write(base + REG_DSI_10nm_PHY_PLL_PLL_LOCK_OVERRIDE, 0x80); + pll_write(base + REG_DSI_10nm_PHY_PLL_PFILT, 0x29); + pll_write(base + REG_DSI_10nm_PHY_PLL_IFILT, 0x3f); +} + +static void dsi_pll_commit(struct dsi_pll_10nm *pll) +{ + void __iomem *base = pll->mmio; + struct dsi_pll_regs *reg = &pll->reg_setup; + + pll_write(base + REG_DSI_10nm_PHY_PLL_CORE_INPUT_OVERRIDE, 0x12); + pll_write(base + REG_DSI_10nm_PHY_PLL_DECIMAL_DIV_START_1, + reg->decimal_div_start); + pll_write(base + REG_DSI_10nm_PHY_PLL_FRAC_DIV_START_LOW_1, + reg->frac_div_start_low); + pll_write(base + REG_DSI_10nm_PHY_PLL_FRAC_DIV_START_MID_1, + reg->frac_div_start_mid); + pll_write(base + REG_DSI_10nm_PHY_PLL_FRAC_DIV_START_HIGH_1, + reg->frac_div_start_high); + pll_write(base + REG_DSI_10nm_PHY_PLL_PLL_LOCKDET_RATE_1, 0x40); + pll_write(base + REG_DSI_10nm_PHY_PLL_PLL_LOCK_DELAY, 0x06); + pll_write(base + REG_DSI_10nm_PHY_PLL_CMODE, 0x10); + pll_write(base + REG_DSI_10nm_PHY_PLL_CLOCK_INVERTERS, + reg->pll_clock_inverters); +} + static int dsi_pll_10nm_vco_set_rate(struct clk_hw *hw, unsigned long rate, unsigned long parent_rate) { @@ -42,18 +315,192 @@ static int dsi_pll_10nm_vco_set_rate(struct clk_hw *hw, unsigned long rate, DBG("DSI PLL%d rate=%lu, parent's=%lu", pll_10nm->id, rate, parent_rate);
+ pll_10nm->vco_current_rate = rate; + pll_10nm->vco_ref_clk_rate = parent_rate; + + dsi_pll_setup_config(pll_10nm); + + dsi_pll_calc_dec_frac(pll_10nm); + + dsi_pll_calc_ssc(pll_10nm); + + dsi_pll_commit(pll_10nm); + + dsi_pll_config_hzindep_reg(pll_10nm); + + dsi_pll_ssc_commit(pll_10nm); + + /* flush, ensure all register writes are done*/ + wmb(); + return 0; }
+static int dsi_pll_10nm_lock_status(struct dsi_pll_10nm *pll) +{ + int rc; + u32 status = 0; + u32 const delay_us = 100; + u32 const timeout_us = 5000; + + rc = readl_poll_timeout_atomic(pll->mmio + + REG_DSI_10nm_PHY_PLL_COMMON_STATUS_ONE, + status, + ((status & BIT(0)) > 0), + delay_us, + timeout_us); + if (rc) + pr_err("DSI PLL(%d) lock failed, status=0x%08x\n", + pll->id, status); + + return rc; +} + +static void dsi_pll_disable_pll_bias(struct dsi_pll_10nm *pll) +{ + u32 data = pll_read(pll->phy_cmn_mmio + REG_DSI_10nm_PHY_CMN_CTRL_0); + + pll_write(pll->mmio + REG_DSI_10nm_PHY_PLL_SYSTEM_MUXES, 0); + pll_write(pll->phy_cmn_mmio + REG_DSI_10nm_PHY_CMN_CTRL_0, + data & ~BIT(5)); + ndelay(250); +} + +static void dsi_pll_enable_pll_bias(struct dsi_pll_10nm *pll) +{ + u32 data = pll_read(pll->phy_cmn_mmio + REG_DSI_10nm_PHY_CMN_CTRL_0); + + pll_write(pll->phy_cmn_mmio + REG_DSI_10nm_PHY_CMN_CTRL_0, + data | BIT(5)); + pll_write(pll->mmio + REG_DSI_10nm_PHY_PLL_SYSTEM_MUXES, 0xc0); + ndelay(250); +} + +static void dsi_pll_disable_global_clk(struct dsi_pll_10nm *pll) +{ + u32 data; + + data = pll_read(pll->phy_cmn_mmio + REG_DSI_10nm_PHY_CMN_CLK_CFG1); + pll_write(pll->phy_cmn_mmio + REG_DSI_10nm_PHY_CMN_CLK_CFG1, + data & ~BIT(5)); +} + +static void dsi_pll_enable_global_clk(struct dsi_pll_10nm *pll) +{ + u32 data; + + data = pll_read(pll->phy_cmn_mmio + REG_DSI_10nm_PHY_CMN_CLK_CFG1); + pll_write(pll->phy_cmn_mmio + REG_DSI_10nm_PHY_CMN_CLK_CFG1, + data | BIT(5)); +} + +static int dsi_pll_10nm_vco_prepare(struct clk_hw *hw) +{ + struct msm_dsi_pll *pll = hw_clk_to_pll(hw); + struct dsi_pll_10nm *pll_10nm = to_pll_10nm(pll); + int rc; + + dsi_pll_enable_pll_bias(pll_10nm); + if (pll_10nm->slave) + dsi_pll_enable_pll_bias(pll_10nm->slave); + + /* Start PLL */ + pll_write(pll_10nm->phy_cmn_mmio + REG_DSI_10nm_PHY_CMN_PLL_CNTRL, + 0x01); + + /* + * ensure all PLL configurations are written prior to checking + * for PLL lock. + */ + wmb(); + + /* Check for PLL lock */ + rc = dsi_pll_10nm_lock_status(pll_10nm); + if (rc) { + pr_err("PLL(%d) lock failed\n", pll_10nm->id); + goto error; + } + + pll->pll_on = true; + + dsi_pll_enable_global_clk(pll_10nm); + if (pll_10nm->slave) + dsi_pll_enable_global_clk(pll_10nm->slave); + + pll_write(pll_10nm->phy_cmn_mmio + REG_DSI_10nm_PHY_CMN_RBUF_CTRL, + 0x01); + if (pll_10nm->slave) + pll_write(pll_10nm->slave->phy_cmn_mmio + + REG_DSI_10nm_PHY_CMN_RBUF_CTRL, 0x01); + +error: + return rc; +} + +static void dsi_pll_disable_sub(struct dsi_pll_10nm *pll) +{ + pll_write(pll->phy_cmn_mmio + REG_DSI_10nm_PHY_CMN_RBUF_CTRL, 0); + dsi_pll_disable_pll_bias(pll); +} + +static void dsi_pll_10nm_vco_unprepare(struct clk_hw *hw) +{ + struct msm_dsi_pll *pll = hw_clk_to_pll(hw); + struct dsi_pll_10nm *pll_10nm = to_pll_10nm(pll); + + /* + * To avoid any stray glitches while abruptly powering down the PLL + * make sure to gate the clock using the clock enable bit before + * powering down the PLL + */ + dsi_pll_disable_global_clk(pll_10nm); + pll_write(pll_10nm->phy_cmn_mmio + REG_DSI_10nm_PHY_CMN_PLL_CNTRL, 0); + dsi_pll_disable_sub(pll_10nm); + if (pll_10nm->slave) { + dsi_pll_disable_global_clk(pll_10nm->slave); + dsi_pll_disable_sub(pll_10nm->slave); + } + /* flush, ensure all register writes are done */ + wmb(); + pll->pll_on = false; +} + static unsigned long dsi_pll_10nm_vco_recalc_rate(struct clk_hw *hw, unsigned long parent_rate) { struct msm_dsi_pll *pll = hw_clk_to_pll(hw); struct dsi_pll_10nm *pll_10nm = to_pll_10nm(pll); + void __iomem *base = pll_10nm->mmio; + u64 ref_clk = pll_10nm->vco_ref_clk_rate; u64 vco_rate = 0x0; - - DBG("DSI PLL%d returning vco rate = %lu", pll_10nm->id, - (unsigned long)vco_rate); + u64 multiplier; + u32 frac; + u32 dec; + u64 pll_freq, tmp64; + + dec = pll_read(base + REG_DSI_10nm_PHY_PLL_DECIMAL_DIV_START_1); + dec &= 0xff; + + frac = pll_read(base + REG_DSI_10nm_PHY_PLL_FRAC_DIV_START_LOW_1); + frac |= ((pll_read(base + REG_DSI_10nm_PHY_PLL_FRAC_DIV_START_MID_1) & + 0xff) << 8); + frac |= ((pll_read(base + REG_DSI_10nm_PHY_PLL_FRAC_DIV_START_HIGH_1) & + 0x3) << 16); + + /* + * TODO: + * 1. Assumes prescaler is disabled + * 2. Multiplier is 2^18. it should be 2^(num_of_frac_bits) + */ + multiplier = 1 << 18; + pll_freq = dec * (ref_clk * 2); + tmp64 = (ref_clk * 2 * frac); + pll_freq += div_u64(tmp64, multiplier); + + vco_rate = pll_freq; + + DBG("DSI PLL%d returning vco rate = %lu, dec = %x, frac = %x", + pll_10nm->id, (unsigned long)vco_rate, dec, frac);
return (unsigned long)vco_rate; } @@ -62,8 +509,8 @@ static const struct clk_ops clk_ops_dsi_pll_10nm_vco = { .round_rate = msm_dsi_pll_helper_clk_round_rate, .set_rate = dsi_pll_10nm_vco_set_rate, .recalc_rate = dsi_pll_10nm_vco_recalc_rate, - .prepare = msm_dsi_pll_helper_clk_prepare, - .unprepare = msm_dsi_pll_helper_clk_unprepare, + .prepare = dsi_pll_10nm_vco_prepare, + .unprepare = dsi_pll_10nm_vco_unprepare, };
/* @@ -73,13 +520,45 @@ static const struct clk_ops clk_ops_dsi_pll_10nm_vco = { static void dsi_pll_10nm_save_state(struct msm_dsi_pll *pll) { struct dsi_pll_10nm *pll_10nm = to_pll_10nm(pll); + struct pll_10nm_cached_state *cached = &pll_10nm->cached_state; + void __iomem *phy_base = pll_10nm->phy_cmn_mmio; + u32 cmn_clk_cfg0, cmn_clk_cfg1;
- DBG("DSI PLL%d", pll_10nm->id); + cached->pll_out_div = pll_read(pll_10nm->mmio + + REG_DSI_10nm_PHY_PLL_PLL_OUTDIV_RATE); + cached->pll_out_div &= 0x3; + + cmn_clk_cfg0 = pll_read(phy_base + REG_DSI_10nm_PHY_CMN_CLK_CFG0); + cached->bit_clk_div = cmn_clk_cfg0 & 0xf; + cached->pix_clk_div = (cmn_clk_cfg0 & 0xf0) >> 4; + + cmn_clk_cfg1 = pll_read(phy_base + REG_DSI_10nm_PHY_CMN_CLK_CFG1); + cached->pll_mux = cmn_clk_cfg1 & 0x3; + + DBG("DSI PLL%d outdiv %x bit_clk_div %x pix_clk_div %x pll_mux %x", + pll_10nm->id, cached->pll_out_div, cached->bit_clk_div, + cached->pix_clk_div, cached->pll_mux); }
static int dsi_pll_10nm_restore_state(struct msm_dsi_pll *pll) { struct dsi_pll_10nm *pll_10nm = to_pll_10nm(pll); + struct pll_10nm_cached_state *cached = &pll_10nm->cached_state; + void __iomem *phy_base = pll_10nm->phy_cmn_mmio; + u32 val; + + val = pll_read(pll_10nm->mmio + REG_DSI_10nm_PHY_PLL_PLL_OUTDIV_RATE); + val &= ~0x3; + val |= cached->pll_out_div; + pll_write(pll_10nm->mmio + REG_DSI_10nm_PHY_PLL_PLL_OUTDIV_RATE, val); + + pll_write(phy_base + REG_DSI_10nm_PHY_CMN_CLK_CFG0, + cached->bit_clk_div | (cached->pix_clk_div << 4)); + + val = pll_read(phy_base + REG_DSI_10nm_PHY_CMN_CLK_CFG1); + val &= ~0x3; + val |= cached->pll_mux; + pll_write(phy_base + REG_DSI_10nm_PHY_CMN_CLK_CFG1, val);
DBG("DSI PLL%d", pll_10nm->id);
@@ -90,9 +569,29 @@ static int dsi_pll_10nm_set_usecase(struct msm_dsi_pll *pll, enum msm_dsi_phy_usecase uc) { struct dsi_pll_10nm *pll_10nm = to_pll_10nm(pll); + void __iomem *base = pll_10nm->phy_cmn_mmio; + u32 data = 0x0; /* internal PLL */
DBG("DSI PLL%d", pll_10nm->id);
+ switch (uc) { + case MSM_DSI_PHY_STANDALONE: + break; + case MSM_DSI_PHY_MASTER: + pll_10nm->slave = pll_10nm_list[(pll_10nm->id + 1) % DSI_MAX]; + break; + case MSM_DSI_PHY_SLAVE: + data = 0x1; /* external PLL */ + break; + default: + return -EINVAL; + } + + /* set PLL src */ + pll_write(base + REG_DSI_10nm_PHY_CMN_CLK_CFG1, (data << 2)); + + pll_10nm->uc = uc; + return 0; }
@@ -101,13 +600,14 @@ static int dsi_pll_10nm_get_provider(struct msm_dsi_pll *pll, struct clk **pixel_clk_provider) { struct dsi_pll_10nm *pll_10nm = to_pll_10nm(pll); + struct clk_hw_onecell_data *hw_data = pll_10nm->hw_data;
DBG("DSI PLL%d", pll_10nm->id);
if (byte_clk_provider) - *byte_clk_provider = NULL; + *byte_clk_provider = hw_data->hws[DSI_BYTE_PLL_CLK]->clk; if (pixel_clk_provider) - *pixel_clk_provider = NULL; + *pixel_clk_provider = hw_data->hws[DSI_PIXEL_PLL_CLK]->clk;
return 0; } @@ -119,8 +619,151 @@ static void dsi_pll_10nm_destroy(struct msm_dsi_pll *pll) DBG("DSI PLL%d", pll_10nm->id); }
+/* + * The post dividers and mux clocks are created using the standard divider and + * mux API. Unlike the 14nm PHY, the slave PLL doesn't need its dividers/mux + * state to follow the master PLL's divider/mux state. Therefore, we don't + * require special clock ops that also configure the slave PLL registers + */ static int pll_10nm_register(struct dsi_pll_10nm *pll_10nm) { + char clk_name[32], parent[32], vco_name[32]; + char parent2[32], parent3[32], parent4[32]; + struct clk_init_data vco_init = { + .parent_names = (const char *[]){ "xo" }, + .num_parents = 1, + .name = vco_name, + .flags = CLK_IGNORE_UNUSED, + .ops = &clk_ops_dsi_pll_10nm_vco, + }; + struct device *dev = &pll_10nm->pdev->dev; + struct clk_hw **hws = pll_10nm->hws; + struct clk_hw_onecell_data *hw_data; + struct clk_hw *hw; + int num = 0; + int ret; + + DBG("DSI%d", pll_10nm->id); + + hw_data = devm_kzalloc(dev, sizeof(*hw_data) + + NUM_PROVIDED_CLKS * sizeof(struct clk_hw *), + GFP_KERNEL); + if (!hw_data) + return -ENOMEM; + + snprintf(vco_name, 32, "dsi%dvco_clk", pll_10nm->id); + pll_10nm->base.clk_hw.init = &vco_init; + + ret = clk_hw_register(dev, &pll_10nm->base.clk_hw); + if (ret) + return ret; + + hws[num++] = &pll_10nm->base.clk_hw; + + snprintf(clk_name, 32, "dsi%d_pll_out_div_clk", pll_10nm->id); + snprintf(parent, 32, "dsi%dvco_clk", pll_10nm->id); + + hw = clk_hw_register_divider(dev, clk_name, + parent, CLK_SET_RATE_PARENT, + pll_10nm->mmio + + REG_DSI_10nm_PHY_PLL_PLL_OUTDIV_RATE, + 0, 2, CLK_DIVIDER_POWER_OF_TWO, NULL); + if (IS_ERR(hw)) + return PTR_ERR(hw); + + hws[num++] = hw; + + snprintf(clk_name, 32, "dsi%d_pll_bit_clk", pll_10nm->id); + snprintf(parent, 32, "dsi%d_pll_out_div_clk", pll_10nm->id); + + /* BIT CLK: DIV_CTRL_3_0 */ + hw = clk_hw_register_divider(dev, clk_name, parent, + CLK_SET_RATE_PARENT, + pll_10nm->phy_cmn_mmio + + REG_DSI_10nm_PHY_CMN_CLK_CFG0, + 0, 4, CLK_DIVIDER_ONE_BASED, + &pll_10nm->postdiv_lock); + if (IS_ERR(hw)) + return PTR_ERR(hw); + + hws[num++] = hw; + + snprintf(clk_name, 32, "dsi%dpllbyte", pll_10nm->id); + snprintf(parent, 32, "dsi%d_pll_bit_clk", pll_10nm->id); + + /* DSI Byte clock = VCO_CLK / OUT_DIV / BIT_DIV / 8 */ + hw = clk_hw_register_fixed_factor(dev, clk_name, parent, + CLK_SET_RATE_PARENT, 1, 8); + if (IS_ERR(hw)) + return PTR_ERR(hw); + + hws[num++] = hw; + hw_data->hws[DSI_BYTE_PLL_CLK] = hw; + + snprintf(clk_name, 32, "dsi%d_pll_by_2_bit_clk", pll_10nm->id); + snprintf(parent, 32, "dsi%d_pll_bit_clk", pll_10nm->id); + + hw = clk_hw_register_fixed_factor(dev, clk_name, parent, + 0, 1, 2); + if (IS_ERR(hw)) + return PTR_ERR(hw); + + hws[num++] = hw; + + snprintf(clk_name, 32, "dsi%d_pll_post_out_div_clk", pll_10nm->id); + snprintf(parent, 32, "dsi%d_pll_out_div_clk", pll_10nm->id); + + hw = clk_hw_register_fixed_factor(dev, clk_name, parent, + 0, 1, 4); + if (IS_ERR(hw)) + return PTR_ERR(hw); + + hws[num++] = hw; + + snprintf(clk_name, 32, "dsi%d_pclk_mux", pll_10nm->id); + snprintf(parent, 32, "dsi%d_pll_bit_clk", pll_10nm->id); + snprintf(parent2, 32, "dsi%d_pll_by_2_bit_clk", pll_10nm->id); + snprintf(parent3, 32, "dsi%d_pll_out_div_clk", pll_10nm->id); + snprintf(parent4, 32, "dsi%d_pll_post_out_div_clk", pll_10nm->id); + + hw = clk_hw_register_mux(dev, clk_name, + (const char *[]){ + parent, parent2, parent3, parent4 + }, 4, 0, pll_10nm->phy_cmn_mmio + + REG_DSI_10nm_PHY_CMN_CLK_CFG1, + 0, 2, 0, NULL); + if (IS_ERR(hw)) + return PTR_ERR(hw); + + hws[num++] = hw; + + snprintf(clk_name, 32, "dsi%dpll", pll_10nm->id); + snprintf(parent, 32, "dsi%d_pclk_mux", pll_10nm->id); + + /* PIX CLK DIV : DIV_CTRL_7_4*/ + hw = clk_hw_register_divider(dev, clk_name, parent, + 0, pll_10nm->phy_cmn_mmio + + REG_DSI_10nm_PHY_CMN_CLK_CFG0, + 4, 4, CLK_DIVIDER_ONE_BASED, + &pll_10nm->postdiv_lock); + if (IS_ERR(hw)) + return PTR_ERR(hw); + + hws[num++] = hw; + hw_data->hws[DSI_PIXEL_PLL_CLK] = hw; + + pll_10nm->num_hws = num; + + hw_data->num = NUM_PROVIDED_CLKS; + pll_10nm->hw_data = hw_data; + + ret = of_clk_add_hw_provider(dev->of_node, of_clk_hw_onecell_get, + pll_10nm->hw_data); + if (ret) { + dev_err(dev, "failed to register clk provider: %d\n", ret); + return ret; + } + return 0; }
@@ -172,5 +815,8 @@ struct msm_dsi_pll *msm_dsi_pll_10nm_init(struct platform_device *pdev, int id) return ERR_PTR(ret); }
+ /* TODO: Remove this when we have proper display handover support */ + msm_dsi_pll_save_state(pll); + return pll; }
Populate the PHY ops with the downstream driver as reference.
There are a couple of TODOs which need to be resolved: - The PHY timings are all hardcoded for now. This needs to be replaced with automatic calculations once we get/understand them. - There are some lane configuration registers which use a new representation between physical and logical lane mappings. For now, we've hardcoced them to follow the default mapping (i.e logical 0 -> phy 0, logical 1 -> phy 1 etc).
Signed-off-by: Archit Taneja architt@codeaurora.org --- drivers/gpu/drm/msm/dsi/phy/dsi_phy_10nm.c | 199 +++++++++++++++++++++++++++++ 1 file changed, 199 insertions(+)
diff --git a/drivers/gpu/drm/msm/dsi/phy/dsi_phy_10nm.c b/drivers/gpu/drm/msm/dsi/phy/dsi_phy_10nm.c index b7545fb63bf5..0af951aaeea1 100644 --- a/drivers/gpu/drm/msm/dsi/phy/dsi_phy_10nm.c +++ b/drivers/gpu/drm/msm/dsi/phy/dsi_phy_10nm.c @@ -8,9 +8,208 @@ #include "dsi_phy.h" #include "dsi.xml.h"
+static int dsi_phy_hw_v3_0_is_pll_on(struct msm_dsi_phy *phy) +{ + void __iomem *base = phy->base; + u32 data = 0; + + data = dsi_phy_read(base + REG_DSI_10nm_PHY_CMN_PLL_CNTRL); + mb(); /* make sure read happened */ + + return (data & BIT(0)); +} + +static void dsi_phy_hw_v3_0_config_lpcdrx(struct msm_dsi_phy *phy, bool enable) +{ + void __iomem *lane_base = phy->lane_base; + int phy_lane_0 = 0; /* TODO: Support all lane swap configs */ + + /* + * LPRX and CDRX need to enabled only for physical data lane + * corresponding to the logical data lane 0 + */ + if (enable) + dsi_phy_write(lane_base + + REG_DSI_10nm_PHY_LN_LPRX_CTRL(phy_lane_0), 0x3); + else + dsi_phy_write(lane_base + + REG_DSI_10nm_PHY_LN_LPRX_CTRL(phy_lane_0), 0); +} + +static void dsi_phy_hw_v3_0_lane_settings(struct msm_dsi_phy *phy) +{ + int i; + u8 tx_dctrl[] = { 0x00, 0x00, 0x00, 0x04, 0x01 }; + void __iomem *lane_base = phy->lane_base; + + /* Strength ctrl settings */ + for (i = 0; i < 5; i++) { + dsi_phy_write(lane_base + REG_DSI_10nm_PHY_LN_LPTX_STR_CTRL(i), + 0x55); + /* + * Disable LPRX and CDRX for all lanes. And later on, it will + * be only enabled for the physical data lane corresponding + * to the logical data lane 0 + */ + dsi_phy_write(lane_base + REG_DSI_10nm_PHY_LN_LPRX_CTRL(i), 0); + dsi_phy_write(lane_base + REG_DSI_10nm_PHY_LN_PIN_SWAP(i), 0x0); + dsi_phy_write(lane_base + REG_DSI_10nm_PHY_LN_HSTX_STR_CTRL(i), + 0x88); + } + + dsi_phy_hw_v3_0_config_lpcdrx(phy, true); + + /* other settings */ + for (i = 0; i < 5; i++) { + dsi_phy_write(lane_base + REG_DSI_10nm_PHY_LN_CFG0(i), 0x0); + dsi_phy_write(lane_base + REG_DSI_10nm_PHY_LN_CFG1(i), 0x0); + dsi_phy_write(lane_base + REG_DSI_10nm_PHY_LN_CFG2(i), 0x0); + dsi_phy_write(lane_base + REG_DSI_10nm_PHY_LN_CFG3(i), + i == 4 ? 0x80 : 0x0); + dsi_phy_write(lane_base + + REG_DSI_10nm_PHY_LN_OFFSET_TOP_CTRL(i), 0x0); + dsi_phy_write(lane_base + + REG_DSI_10nm_PHY_LN_OFFSET_BOT_CTRL(i), 0x0); + dsi_phy_write(lane_base + REG_DSI_10nm_PHY_LN_TX_DCTRL(i), + tx_dctrl[i]); + } + + /* Toggle BIT 0 to release freeze I/0 */ + dsi_phy_write(lane_base + REG_DSI_10nm_PHY_LN_TX_DCTRL(3), 0x05); + dsi_phy_write(lane_base + REG_DSI_10nm_PHY_LN_TX_DCTRL(3), 0x04); +} + +static int msm_dsi_dphy_timing_calc_v3(struct msm_dsi_dphy_timing *timing, + struct msm_dsi_phy_clk_request *clk_req) +{ + /* + * TODO: These params need to be computed, they're currently hardcoded + * for a 1440x2560@60Hz panel with a byteclk of 100.618 Mhz, and a + * default escape clock of 19.2 Mhz. + */ + + timing->hs_halfbyte_en = 0; + timing->clk_zero = 0x1c; + timing->clk_prepare = 0x07; + timing->clk_trail = 0x07; + timing->hs_exit = 0x23; + timing->hs_zero = 0x21; + timing->hs_prepare = 0x07; + timing->hs_trail = 0x07; + timing->hs_rqst = 0x05; + timing->ta_sure = 0x00; + timing->ta_go = 0x03; + timing->ta_get = 0x04; + + timing->shared_timings.clk_pre = 0x2d; + timing->shared_timings.clk_post = 0x0d; + + return 0; +} + static int dsi_10nm_phy_enable(struct msm_dsi_phy *phy, int src_pll_id, struct msm_dsi_phy_clk_request *clk_req) { + int ret; + u32 status; + u32 const delay_us = 5; + u32 const timeout_us = 1000; + struct msm_dsi_dphy_timing *timing = &phy->timing; + void __iomem *base = phy->base; + u32 data; + + DBG(""); + + if (msm_dsi_dphy_timing_calc_v3(timing, clk_req)) { + dev_err(&phy->pdev->dev, + "%s: D-PHY timing calculation failed\n", __func__); + return -EINVAL; + } + + if (dsi_phy_hw_v3_0_is_pll_on(phy)) + pr_warn("PLL turned on before configuring PHY\n"); + + /* wait for REFGEN READY */ + ret = readl_poll_timeout_atomic(base + REG_DSI_10nm_PHY_CMN_PHY_STATUS, + status, (status & BIT(0)), + delay_us, timeout_us); + if (ret) { + pr_err("Ref gen not ready. Aborting\n"); + return -EINVAL; + } + + /* de-assert digital and pll power down */ + data = BIT(6) | BIT(5); + dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_CTRL_0, data); + + /* Assert PLL core reset */ + dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_PLL_CNTRL, 0x00); + + /* turn off resync FIFO */ + dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_RBUF_CTRL, 0x00); + + /* Select MS1 byte-clk */ + dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_GLBL_CTRL, 0x10); + + /* Enable LDO */ + dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_VREG_CTRL, 0x59); + + /* Configure PHY lane swap (TODO: we need to calculate this) */ + dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_LANE_CFG0, 0x21); + dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_LANE_CFG1, 0x84); + + /* DSI PHY timings */ + dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_TIMING_CTRL_0, + timing->hs_halfbyte_en); + dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_TIMING_CTRL_1, + timing->clk_zero); + dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_TIMING_CTRL_2, + timing->clk_prepare); + dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_TIMING_CTRL_3, + timing->clk_trail); + dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_TIMING_CTRL_4, + timing->hs_exit); + dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_TIMING_CTRL_5, + timing->hs_zero); + dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_TIMING_CTRL_6, + timing->hs_prepare); + dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_TIMING_CTRL_7, + timing->hs_trail); + dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_TIMING_CTRL_8, + timing->hs_rqst); + dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_TIMING_CTRL_9, + timing->ta_go | (timing->ta_sure << 3)); + dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_TIMING_CTRL_10, + timing->ta_get); + dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_TIMING_CTRL_11, + 0x00); + + /* Remove power down from all blocks */ + dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_CTRL_0, 0x7f); + + /* power up lanes */ + data = dsi_phy_read(base + REG_DSI_10nm_PHY_CMN_CTRL_0); + + /* TODO: only power up lanes that are used */ + data |= 0x1F; + dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_CTRL_0, data); + dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_LANE_CTRL0, 0x1F); + + /* Select full-rate mode */ + dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_CTRL_2, 0x40); + + ret = msm_dsi_pll_set_usecase(phy->pll, phy->usecase); + if (ret) { + dev_err(&phy->pdev->dev, "%s: set pll usecase failed, %d\n", + __func__, ret); + return ret; + } + + /* DSI lane settings */ + dsi_phy_hw_v3_0_lane_settings(phy); + + DBG("DSI%d PHY enabled", phy->id); + return 0; }
dri-devel@lists.freedesktop.org
-
Archit Taneja