The Following should be CC'd to stable: * drm/mgag200: Fix writes into MGA1064_PIX_CLK_CTL register * drm/mgag200: Fix framebuffer base address programming
The others are bug fixes, but aren't critical. I'm sitting on some hardware cursor code that depends on all of these patches before it can go in. I'm aiming for 3.11 for the hardware cursor support.
thanks, Christopher Harvey (4): drm/mgag200: Don't change unrelated registers during modeset drm/mgag200: Fix writes into MGA1064_PIX_CLK_CTL register drm/mgag200: Convert counter delays to jiffies drm/mgag200: Fix framebuffer base address programming
drivers/gpu/drm/mgag200/mgag200_mode.c | 90 ++++++++++++++++++++-------------- 1 file changed, 52 insertions(+), 38 deletions(-)
Signed-off-by: Christopher Harvey charvey@matrox.com --- drivers/gpu/drm/mgag200/mgag200_mode.c | 15 ++++++--------- 1 file changed, 6 insertions(+), 9 deletions(-)
diff --git a/drivers/gpu/drm/mgag200/mgag200_mode.c b/drivers/gpu/drm/mgag200/mgag200_mode.c index 6f3b9db..6dbf6de 100644 --- a/drivers/gpu/drm/mgag200/mgag200_mode.c +++ b/drivers/gpu/drm/mgag200/mgag200_mode.c @@ -46,29 +46,26 @@ static void mga_crtc_load_lut(struct drm_crtc *crtc)
static inline void mga_wait_vsync(struct mga_device *mdev) { - unsigned int count = 0; + unsigned long timeout = jiffies + HZ/10; unsigned int status = 0;
do { status = RREG32(MGAREG_Status); - count++; - } while ((status & 0x08) && (count < 250000)); - count = 0; + } while ((status & 0x08) && time_before(jiffies, timeout)); + timeout = jiffies + HZ/10; status = 0; do { status = RREG32(MGAREG_Status); - count++; - } while (!(status & 0x08) && (count < 250000)); + } while (!(status & 0x08) && time_before(jiffies, timeout)); }
static inline void mga_wait_busy(struct mga_device *mdev) { - unsigned int count = 0; + unsigned long timeout = jiffies + HZ; unsigned int status = 0; do { status = RREG8(MGAREG_Status + 2); - count++; - } while ((status & 0x01) && (count < 500000)); + } while ((status & 0x01) && time_before(jiffies, timeout)); }
/*
Higher bits of the base address of framebuffers weren't being programmed properly. This caused framebuffers that didn't happen to be allocated at a low enough address to not be displayed properly.
Signed-off-by: Christopher Harvey charvey@matrox.com Signed-off-by: Mathieu Larouche mathieu.larouche@matrox.com --- drivers/gpu/drm/mgag200/mgag200_mode.c | 27 ++++++++++++++++++++++++--- 1 file changed, 24 insertions(+), 3 deletions(-)
diff --git a/drivers/gpu/drm/mgag200/mgag200_mode.c b/drivers/gpu/drm/mgag200/mgag200_mode.c index 6dbf6de..77b8a45 100644 --- a/drivers/gpu/drm/mgag200/mgag200_mode.c +++ b/drivers/gpu/drm/mgag200/mgag200_mode.c @@ -654,12 +654,26 @@ static void mga_g200wb_commit(struct drm_crtc *crtc) WREG_DAC(MGA1064_GEN_IO_DATA, tmp); }
- +/* + This is how the framebuffer base address is stored in g200 cards: + * Assume @offset is the gpu_addr variable of the framebuffer object + * Then addr is the number of _pixels_ (not bytes) from the start of + VRAM to the first pixel we want to display. (divided by 2 for 32bit + framebuffers) + * addr is stored in the CRTCEXT0, CRTCC and CRTCD registers + addr<20> -> CRTCEXT0<6> + addr<19-16> -> CRTCEXT0<3-0> + addr<15-8> -> CRTCC<7-0> + addr<7-0> -> CRTCD<7-0> + CRTCEXT0 has to be programmed last to trigger an update and make the + new addr variable take effect. + */ void mga_set_start_address(struct drm_crtc *crtc, unsigned offset) { struct mga_device *mdev = crtc->dev->dev_private; u32 addr; int count; + u8 crtcext0;
while (RREG8(0x1fda) & 0x08); while (!(RREG8(0x1fda) & 0x08)); @@ -667,10 +681,17 @@ void mga_set_start_address(struct drm_crtc *crtc, unsigned offset) count = RREG8(MGAREG_VCOUNT) + 2; while (RREG8(MGAREG_VCOUNT) < count);
- addr = offset >> 2; + WREG8(MGAREG_CRTCEXT_INDEX, 0); + crtcext0 = RREG8(MGAREG_CRTCEXT_DATA); + crtcext0 &= 0xB0; + addr = offset / 8; + /* Can't store addresses any higher than that... + but we also don't have more than 16MB of memory, so it should be fine. */ + WARN_ON(addr > 0x1fffff); + crtcext0 |= (!!(addr & (1<<20)))<<6; WREG_CRT(0x0d, (u8)(addr & 0xff)); WREG_CRT(0x0c, (u8)(addr >> 8) & 0xff); - WREG_CRT(0xaf, (u8)(addr >> 16) & 0xf); + WREG_ECRT(0x0, ((u8)(addr >> 16) & 0xf) | crtcext0); }
Registers in indices below 0x18 are totally unrelated to modesetting, so don't write 0's, or anything else into them on modeset. Most of these registers are hardware cursor related, so this existing code interferes with hardware cursor development.
Signed-off-by: Christopher Harvey charvey@matrox.com --- drivers/gpu/drm/mgag200/mgag200_mode.c | 6 +----- 1 file changed, 1 insertion(+), 5 deletions(-)
diff --git a/drivers/gpu/drm/mgag200/mgag200_mode.c b/drivers/gpu/drm/mgag200/mgag200_mode.c index f988965..2d9333d 100644 --- a/drivers/gpu/drm/mgag200/mgag200_mode.c +++ b/drivers/gpu/drm/mgag200/mgag200_mode.c @@ -829,11 +829,7 @@ static int mga_crtc_mode_set(struct drm_crtc *crtc,
for (i = 0; i < sizeof(dacvalue); i++) { - if ((i <= 0x03) || - (i == 0x07) || - (i == 0x0b) || - (i == 0x0f) || - ((i >= 0x13) && (i <= 0x17)) || + if ((i <= 0x17) || (i == 0x1b) || (i == 0x1c) || ((i >= 0x1f) && (i <= 0x29)) ||
The original line, WREG_DAC(MGA1064_PIX_CLK_CTL_CLK_DIS, tmp); wrote tmp into MGA1064_PIX_CLK_CTL_CLK_DIS, where MGA1064_PIX_CLK_CTL_CLK_DIS is an offset into MGA1064_PIX_CLK_CTL. Change the line to write properly into MGA1064_PIX_CLK_CTL. There were other chunks of code nearby that use the same pattern (but work correctly), so this patch updates them all to use this new (slightly more efficient) write pattern. The WREG_DAC macro was causing the DAC_INDEX register to be set to the same value twice. WREG8(DAC_DATA, foo) takes advantage of the fact that DAC_INDEX is already at the value we want.
Signed-off-by: Christopher Harvey charvey@matrox.com --- drivers/gpu/drm/mgag200/mgag200_mode.c | 42 +++++++++++++++++----------------- 1 file changed, 21 insertions(+), 21 deletions(-)
diff --git a/drivers/gpu/drm/mgag200/mgag200_mode.c b/drivers/gpu/drm/mgag200/mgag200_mode.c index 2d9333d..6f3b9db 100644 --- a/drivers/gpu/drm/mgag200/mgag200_mode.c +++ b/drivers/gpu/drm/mgag200/mgag200_mode.c @@ -189,12 +189,12 @@ static int mga_g200wb_set_plls(struct mga_device *mdev, long clock) WREG8(DAC_INDEX, MGA1064_PIX_CLK_CTL); tmp = RREG8(DAC_DATA); tmp |= MGA1064_PIX_CLK_CTL_CLK_DIS; - WREG_DAC(MGA1064_PIX_CLK_CTL_CLK_DIS, tmp); + WREG8(DAC_DATA, tmp);
WREG8(DAC_INDEX, MGA1064_REMHEADCTL); tmp = RREG8(DAC_DATA); tmp |= MGA1064_REMHEADCTL_CLKDIS; - WREG_DAC(MGA1064_REMHEADCTL, tmp); + WREG8(DAC_DATA, tmp);
/* select PLL Set C */ tmp = RREG8(MGAREG_MEM_MISC_READ); @@ -204,7 +204,7 @@ static int mga_g200wb_set_plls(struct mga_device *mdev, long clock) WREG8(DAC_INDEX, MGA1064_PIX_CLK_CTL); tmp = RREG8(DAC_DATA); tmp |= MGA1064_PIX_CLK_CTL_CLK_POW_DOWN | 0x80; - WREG_DAC(MGA1064_PIX_CLK_CTL, tmp); + WREG8(DAC_DATA, tmp);
udelay(500);
@@ -212,7 +212,7 @@ static int mga_g200wb_set_plls(struct mga_device *mdev, long clock) WREG8(DAC_INDEX, MGA1064_VREF_CTL); tmp = RREG8(DAC_DATA); tmp &= ~0x04; - WREG_DAC(MGA1064_VREF_CTL, tmp); + WREG8(DAC_DATA, tmp);
udelay(50);
@@ -236,13 +236,13 @@ static int mga_g200wb_set_plls(struct mga_device *mdev, long clock) tmp = RREG8(DAC_DATA); tmp &= ~MGA1064_PIX_CLK_CTL_SEL_MSK; tmp |= MGA1064_PIX_CLK_CTL_SEL_PLL; - WREG_DAC(MGA1064_PIX_CLK_CTL, tmp); + WREG8(DAC_DATA, tmp);
WREG8(DAC_INDEX, MGA1064_REMHEADCTL); tmp = RREG8(DAC_DATA); tmp &= ~MGA1064_REMHEADCTL_CLKSL_MSK; tmp |= MGA1064_REMHEADCTL_CLKSL_PLL; - WREG_DAC(MGA1064_REMHEADCTL, tmp); + WREG8(DAC_DATA, tmp);
/* reset dotclock rate bit */ WREG8(MGAREG_SEQ_INDEX, 1); @@ -253,7 +253,7 @@ static int mga_g200wb_set_plls(struct mga_device *mdev, long clock) WREG8(DAC_INDEX, MGA1064_PIX_CLK_CTL); tmp = RREG8(DAC_DATA); tmp &= ~MGA1064_PIX_CLK_CTL_CLK_DIS; - WREG_DAC(MGA1064_PIX_CLK_CTL, tmp); + WREG8(DAC_DATA, tmp);
vcount = RREG8(MGAREG_VCOUNT);
@@ -318,7 +318,7 @@ static int mga_g200ev_set_plls(struct mga_device *mdev, long clock) WREG8(DAC_INDEX, MGA1064_PIX_CLK_CTL); tmp = RREG8(DAC_DATA); tmp |= MGA1064_PIX_CLK_CTL_CLK_DIS; - WREG_DAC(MGA1064_PIX_CLK_CTL_CLK_DIS, tmp); + WREG8(DAC_DATA, tmp);
tmp = RREG8(MGAREG_MEM_MISC_READ); tmp |= 0x3 << 2; @@ -326,12 +326,12 @@ static int mga_g200ev_set_plls(struct mga_device *mdev, long clock)
WREG8(DAC_INDEX, MGA1064_PIX_PLL_STAT); tmp = RREG8(DAC_DATA); - WREG_DAC(MGA1064_PIX_PLL_STAT, tmp & ~0x40); + WREG8(DAC_DATA, tmp & ~0x40);
WREG8(DAC_INDEX, MGA1064_PIX_CLK_CTL); tmp = RREG8(DAC_DATA); tmp |= MGA1064_PIX_CLK_CTL_CLK_POW_DOWN; - WREG_DAC(MGA1064_PIX_CLK_CTL, tmp); + WREG8(DAC_DATA, tmp);
WREG_DAC(MGA1064_EV_PIX_PLLC_M, m); WREG_DAC(MGA1064_EV_PIX_PLLC_N, n); @@ -342,7 +342,7 @@ static int mga_g200ev_set_plls(struct mga_device *mdev, long clock) WREG8(DAC_INDEX, MGA1064_PIX_CLK_CTL); tmp = RREG8(DAC_DATA); tmp &= ~MGA1064_PIX_CLK_CTL_CLK_POW_DOWN; - WREG_DAC(MGA1064_PIX_CLK_CTL, tmp); + WREG8(DAC_DATA, tmp);
udelay(500);
@@ -350,11 +350,11 @@ static int mga_g200ev_set_plls(struct mga_device *mdev, long clock) tmp = RREG8(DAC_DATA); tmp &= ~MGA1064_PIX_CLK_CTL_SEL_MSK; tmp |= MGA1064_PIX_CLK_CTL_SEL_PLL; - WREG_DAC(MGA1064_PIX_CLK_CTL, tmp); + WREG8(DAC_DATA, tmp);
WREG8(DAC_INDEX, MGA1064_PIX_PLL_STAT); tmp = RREG8(DAC_DATA); - WREG_DAC(MGA1064_PIX_PLL_STAT, tmp | 0x40); + WREG8(DAC_DATA, tmp | 0x40);
tmp = RREG8(MGAREG_MEM_MISC_READ); tmp |= (0x3 << 2); @@ -363,7 +363,7 @@ static int mga_g200ev_set_plls(struct mga_device *mdev, long clock) WREG8(DAC_INDEX, MGA1064_PIX_CLK_CTL); tmp = RREG8(DAC_DATA); tmp &= ~MGA1064_PIX_CLK_CTL_CLK_DIS; - WREG_DAC(MGA1064_PIX_CLK_CTL, tmp); + WREG8(DAC_DATA, tmp);
return 0; } @@ -416,7 +416,7 @@ static int mga_g200eh_set_plls(struct mga_device *mdev, long clock) WREG8(DAC_INDEX, MGA1064_PIX_CLK_CTL); tmp = RREG8(DAC_DATA); tmp |= MGA1064_PIX_CLK_CTL_CLK_DIS; - WREG_DAC(MGA1064_PIX_CLK_CTL_CLK_DIS, tmp); + WREG8(DAC_DATA, tmp);
tmp = RREG8(MGAREG_MEM_MISC_READ); tmp |= 0x3 << 2; @@ -425,7 +425,7 @@ static int mga_g200eh_set_plls(struct mga_device *mdev, long clock) WREG8(DAC_INDEX, MGA1064_PIX_CLK_CTL); tmp = RREG8(DAC_DATA); tmp |= MGA1064_PIX_CLK_CTL_CLK_POW_DOWN; - WREG_DAC(MGA1064_PIX_CLK_CTL, tmp); + WREG8(DAC_DATA, tmp);
udelay(500);
@@ -439,13 +439,13 @@ static int mga_g200eh_set_plls(struct mga_device *mdev, long clock) tmp = RREG8(DAC_DATA); tmp &= ~MGA1064_PIX_CLK_CTL_SEL_MSK; tmp |= MGA1064_PIX_CLK_CTL_SEL_PLL; - WREG_DAC(MGA1064_PIX_CLK_CTL, tmp); + WREG8(DAC_DATA, tmp);
WREG8(DAC_INDEX, MGA1064_PIX_CLK_CTL); tmp = RREG8(DAC_DATA); tmp &= ~MGA1064_PIX_CLK_CTL_CLK_DIS; tmp &= ~MGA1064_PIX_CLK_CTL_CLK_POW_DOWN; - WREG_DAC(MGA1064_PIX_CLK_CTL, tmp); + WREG8(DAC_DATA, tmp);
vcount = RREG8(MGAREG_VCOUNT);
@@ -515,12 +515,12 @@ static int mga_g200er_set_plls(struct mga_device *mdev, long clock) WREG8(DAC_INDEX, MGA1064_PIX_CLK_CTL); tmp = RREG8(DAC_DATA); tmp |= MGA1064_PIX_CLK_CTL_CLK_DIS; - WREG_DAC(MGA1064_PIX_CLK_CTL_CLK_DIS, tmp); + WREG8(DAC_DATA, tmp);
WREG8(DAC_INDEX, MGA1064_REMHEADCTL); tmp = RREG8(DAC_DATA); tmp |= MGA1064_REMHEADCTL_CLKDIS; - WREG_DAC(MGA1064_REMHEADCTL, tmp); + WREG8(DAC_DATA, tmp);
tmp = RREG8(MGAREG_MEM_MISC_READ); tmp |= (0x3<<2) | 0xc0; @@ -530,7 +530,7 @@ static int mga_g200er_set_plls(struct mga_device *mdev, long clock) tmp = RREG8(DAC_DATA); tmp &= ~MGA1064_PIX_CLK_CTL_CLK_DIS; tmp |= MGA1064_PIX_CLK_CTL_CLK_POW_DOWN; - WREG_DAC(MGA1064_PIX_CLK_CTL, tmp); + WREG8(DAC_DATA, tmp);
udelay(500);
Christopher Harvey charvey@matrox.com writes:
The Following should be CC'd to stable:
- drm/mgag200: Fix writes into MGA1064_PIX_CLK_CTL register
- drm/mgag200: Fix framebuffer base address programming
The others are bug fixes, but aren't critical. I'm sitting on some hardware cursor code that depends on all of these patches before it can go in. I'm aiming for 3.11 for the hardware cursor support.
thanks, Christopher Harvey (4): drm/mgag200: Don't change unrelated registers during modeset drm/mgag200: Fix writes into MGA1064_PIX_CLK_CTL register drm/mgag200: Convert counter delays to jiffies drm/mgag200: Fix framebuffer base address programming
drivers/gpu/drm/mgag200/mgag200_mode.c | 90 ++++++++++++++++++++-------------- 1 file changed, 52 insertions(+), 38 deletions(-)
please ignore this, version 2 has been posted.
-C
dri-devel@lists.freedesktop.org
-
Christopher Harvey