This describes the ASPEED BMC SoC's display controller.

Signed-off-by: Joel Stanley joel@jms.id.au Reviewed-by: Andrew Jeffery andrew@aj.id.au --- v3: Add Andrew's reviewed-by

.../devicetree/bindings/gpu/aspeed-gfx.txt | 41 +++++++++++++++++++ 1 file changed, 41 insertions(+) create mode 100644 Documentation/devicetree/bindings/gpu/aspeed-gfx.txt

diff --git a/Documentation/devicetree/bindings/gpu/aspeed-gfx.txt b/Documentation/devicetree/bindings/gpu/aspeed-gfx.txt new file mode 100644 index 000000000000..a74033332668 --- /dev/null +++ b/Documentation/devicetree/bindings/gpu/aspeed-gfx.txt @@ -0,0 +1,41 @@ +Device tree configuration for the GFX display deivce on the AST2500 SoCs. + +Required properties: + - compatible + * Must be one of the following: + + aspeed,ast2500-gfx + + aspeed,ast2400-gfx + * In addition, the ASPEED pinctrl bindings require the 'syscon' property to + be present + + - reg: Physical base address and length of the GFX registers + + - interrupts: interrupt number for the GFX device + + - clocks: clock number used to generate the pixel clock + + - resets: reset line that must be released to use the GFX device + + - memory-region: + Phandle to a memory region to allocate from, as defined in + Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt + + +Example: + +gfx: display@1e6e6000 { + compatible = "aspeed,ast2500-gfx", "syscon"; + reg = <0x1e6e6000 0x1000>; + reg-io-width = <4>; + clocks = <&syscon ASPEED_CLK_GATE_D1CLK>; + resets = <&syscon ASPEED_RESET_CRT1>; + interrupts = <0x19>; + memory-region = <&gfx_memory>; +}; + +gfx_memory: framebuffer { + size = <0x01000000>; + alignment = <0x01000000>; + compatible = "shared-dma-pool"; + reusable; +};

This driver is for the ASPEED BMC SoC's GFX display hardware. This driver runs on the ARM based BMC systems, unlike the ast driver which runs on a host CPU and is is for a PCI graphics device.

Signed-off-by: Joel Stanley joel@jms.id.au Acked-by: Daniel Vetter daniel.vetter@ffwll.ch Reviewed-by: Noralf Trønnes noralf@tronnes.org Reviewed-by: Sam Ravnborg sam@ravnborg.org --- v3: Really remove drmP.h Remove legacy DRIVER_HAVE_IRQ v2: Use drm_gem_fb_simple_display_pipe_prepare_fb Sort headers Remove drmP.h inclusion Replace gem callbacks with those suggested by Noralf Use drm_connector_cleanup Drop null check for embedddd crtc object Tweaks to spelling in kerneldoc Drop DRM_KMS_FB_HELPER to make fbdev emulation optional Remove ast2400 compatible as the ast2400 support is untested

Changes since RFC: drm_fbdev_cma_init -> drm_fb_cma_fbdev_init and use generic lastclose callback Use generic irq handling instead of drm_irq_install Add doc to driver Get rid of unncessary reads in irq enable/disable path Rebase on linux-next

--- drivers/gpu/drm/Kconfig | 2 + drivers/gpu/drm/Makefile | 1 + drivers/gpu/drm/aspeed/Kconfig | 14 ++ drivers/gpu/drm/aspeed/Makefile | 3 + drivers/gpu/drm/aspeed/aspeed_gfx.h | 104 +++++++++ drivers/gpu/drm/aspeed/aspeed_gfx_crtc.c | 241 ++++++++++++++++++++ drivers/gpu/drm/aspeed/aspeed_gfx_drv.c | 269 +++++++++++++++++++++++ drivers/gpu/drm/aspeed/aspeed_gfx_out.c | 42 ++++ 8 files changed, 676 insertions(+) create mode 100644 drivers/gpu/drm/aspeed/Kconfig create mode 100644 drivers/gpu/drm/aspeed/Makefile create mode 100644 drivers/gpu/drm/aspeed/aspeed_gfx.h create mode 100644 drivers/gpu/drm/aspeed/aspeed_gfx_crtc.c create mode 100644 drivers/gpu/drm/aspeed/aspeed_gfx_drv.c create mode 100644 drivers/gpu/drm/aspeed/aspeed_gfx_out.c

diff --git a/drivers/gpu/drm/Kconfig b/drivers/gpu/drm/Kconfig index 82bb221ec94e..b1ec8f85c2a8 100644 --- a/drivers/gpu/drm/Kconfig +++ b/drivers/gpu/drm/Kconfig @@ -335,6 +335,8 @@ source "drivers/gpu/drm/xen/Kconfig"

source "drivers/gpu/drm/vboxvideo/Kconfig"

+source "drivers/gpu/drm/aspeed/Kconfig" + # Keep legacy drivers last

menuconfig DRM_LEGACY diff --git a/drivers/gpu/drm/Makefile b/drivers/gpu/drm/Makefile index 0baf148e3687..df8835045310 100644 --- a/drivers/gpu/drm/Makefile +++ b/drivers/gpu/drm/Makefile @@ -110,3 +110,4 @@ obj-$(CONFIG_DRM_PL111) += pl111/ obj-$(CONFIG_DRM_TVE200) += tve200/ obj-$(CONFIG_DRM_XEN) += xen/ obj-$(CONFIG_DRM_VBOXVIDEO) += vboxvideo/ +obj-$(CONFIG_DRM_ASPEED_GFX) += aspeed/ diff --git a/drivers/gpu/drm/aspeed/Kconfig b/drivers/gpu/drm/aspeed/Kconfig new file mode 100644 index 000000000000..42b74d18a41b --- /dev/null +++ b/drivers/gpu/drm/aspeed/Kconfig @@ -0,0 +1,14 @@ +config DRM_ASPEED_GFX + tristate "ASPEED BMC Display Controller" + depends on DRM && OF + select DRM_KMS_HELPER + select DRM_KMS_CMA_HELPER + select DRM_PANEL + select DMA_CMA + select CMA + select MFD_SYSCON + help + Chose this option if you have an ASPEED AST2500 SOC Display + Controller (aka GFX). + + If M is selected this module will be called aspeed_gfx. diff --git a/drivers/gpu/drm/aspeed/Makefile b/drivers/gpu/drm/aspeed/Makefile new file mode 100644 index 000000000000..6e194cd790d8 --- /dev/null +++ b/drivers/gpu/drm/aspeed/Makefile @@ -0,0 +1,3 @@ +aspeed_gfx-y := aspeed_gfx_drv.o aspeed_gfx_crtc.o aspeed_gfx_out.o + +obj-$(CONFIG_DRM_ASPEED_GFX) += aspeed_gfx.o diff --git a/drivers/gpu/drm/aspeed/aspeed_gfx.h b/drivers/gpu/drm/aspeed/aspeed_gfx.h new file mode 100644 index 000000000000..b7a986e49177 --- /dev/null +++ b/drivers/gpu/drm/aspeed/aspeed_gfx.h @@ -0,0 +1,104 @@ +// SPDX-License-Identifier: GPL-2.0+ +// Copyright 2018 IBM Corporation + +#include <drm/drm_device.h> +#include <drm/drm_simple_kms_helper.h> + +struct aspeed_gfx { + void __iomem *base; + struct clk *clk; + struct reset_control *rst; + struct regmap *scu; + + struct drm_simple_display_pipe pipe; + struct drm_connector connector; + struct drm_fbdev_cma *fbdev; +}; + +int aspeed_gfx_create_pipe(struct drm_device *drm); +int aspeed_gfx_create_output(struct drm_device *drm); + +#define CRT_CTRL1 0x60 /* CRT Control I */ +#define CRT_CTRL2 0x64 /* CRT Control II */ +#define CRT_STATUS 0x68 /* CRT Status */ +#define CRT_MISC 0x6c /* CRT Misc Setting */ +#define CRT_HORIZ0 0x70 /* CRT Horizontal Total & Display Enable End */ +#define CRT_HORIZ1 0x74 /* CRT Horizontal Retrace Start & End */ +#define CRT_VERT0 0x78 /* CRT Vertical Total & Display Enable End */ +#define CRT_VERT1 0x7C /* CRT Vertical Retrace Start & End */ +#define CRT_ADDR 0x80 /* CRT Display Starting Address */ +#define CRT_OFFSET 0x84 /* CRT Display Offset & Terminal Count */ +#define CRT_THROD 0x88 /* CRT Threshold */ +#define CRT_XSCALE 0x8C /* CRT Scaling-Up Factor */ +#define CRT_CURSOR0 0x90 /* CRT Hardware Cursor X & Y Offset */ +#define CRT_CURSOR1 0x94 /* CRT Hardware Cursor X & Y Position */ +#define CRT_CURSOR2 0x98 /* CRT Hardware Cursor Pattern Address */ +#define CRT_9C 0x9C +#define CRT_OSD_H 0xA0 /* CRT OSD Horizontal Start/End */ +#define CRT_OSD_V 0xA4 /* CRT OSD Vertical Start/End */ +#define CRT_OSD_ADDR 0xA8 /* CRT OSD Pattern Address */ +#define CRT_OSD_DISP 0xAC /* CRT OSD Offset */ +#define CRT_OSD_THRESH 0xB0 /* CRT OSD Threshold & Alpha */ +#define CRT_B4 0xB4 +#define CRT_STS_V 0xB8 /* CRT Status V */ +#define CRT_SCRATCH 0xBC /* Scratchpad */ +#define CRT_BB0_ADDR 0xD0 /* CRT Display BB0 Starting Address */ +#define CRT_BB1_ADDR 0xD4 /* CRT Display BB1 Starting Address */ +#define CRT_BB_COUNT 0xD8 /* CRT Display BB Terminal Count */ +#define OSD_COLOR1 0xE0 /* OSD Color Palette Index 1 & 0 */ +#define OSD_COLOR2 0xE4 /* OSD Color Palette Index 3 & 2 */ +#define OSD_COLOR3 0xE8 /* OSD Color Palette Index 5 & 4 */ +#define OSD_COLOR4 0xEC /* OSD Color Palette Index 7 & 6 */ +#define OSD_COLOR5 0xF0 /* OSD Color Palette Index 9 & 8 */ +#define OSD_COLOR6 0xF4 /* OSD Color Palette Index 11 & 10 */ +#define OSD_COLOR7 0xF8 /* OSD Color Palette Index 13 & 12 */ +#define OSD_COLOR8 0xFC /* OSD Color Palette Index 15 & 14 */ + +/* CTRL1 */ +#define CRT_CTRL_EN BIT(0) +#define CRT_CTRL_HW_CURSOR_EN BIT(1) +#define CRT_CTRL_OSD_EN BIT(2) +#define CRT_CTRL_INTERLACED BIT(3) +#define CRT_CTRL_COLOR_RGB565 (0 << 7) +#define CRT_CTRL_COLOR_YUV444 (1 << 7) +#define CRT_CTRL_COLOR_XRGB8888 (2 << 7) +#define CRT_CTRL_COLOR_RGB888 (3 << 7) +#define CRT_CTRL_COLOR_YUV444_2RGB (5 << 7) +#define CRT_CTRL_COLOR_YUV422 (7 << 7) +#define CRT_CTRL_COLOR_MASK GENMASK(9, 7) +#define CRT_CTRL_HSYNC_NEGATIVE BIT(16) +#define CRT_CTRL_VSYNC_NEGATIVE BIT(17) +#define CRT_CTRL_VERTICAL_INTR_EN BIT(30) +#define CRT_CTRL_VERTICAL_INTR_STS BIT(31) + +/* CTRL2 */ +#define CRT_CTRL_DAC_EN BIT(0) +#define CRT_CTRL_VBLANK_LINE(x) (((x) << 20) & CRT_CTRL_VBLANK_LINE_MASK) +#define CRT_CTRL_VBLANK_LINE_MASK GENMASK(20, 31) + +/* CRT_HORIZ0 */ +#define CRT_H_TOTAL(x) (x) +#define CRT_H_DE(x) ((x) << 16) + +/* CRT_HORIZ1 */ +#define CRT_H_RS_START(x) (x) +#define CRT_H_RS_END(x) ((x) << 16) + +/* CRT_VIRT0 */ +#define CRT_V_TOTAL(x) (x) +#define CRT_V_DE(x) ((x) << 16) + +/* CRT_VIRT1 */ +#define CRT_V_RS_START(x) (x) +#define CRT_V_RS_END(x) ((x) << 16) + +/* CRT_OFFSET */ +#define CRT_DISP_OFFSET(x) (x) +#define CRT_TERM_COUNT(x) ((x) << 16) + +/* CRT_THROD */ +#define CRT_THROD_LOW(x) (x) +#define CRT_THROD_HIGH(x) ((x) << 8) + +/* Default Threshold Seting */ +#define G5_CRT_THROD_VAL (CRT_THROD_LOW(0x24) | CRT_THROD_HIGH(0x3C)) diff --git a/drivers/gpu/drm/aspeed/aspeed_gfx_crtc.c b/drivers/gpu/drm/aspeed/aspeed_gfx_crtc.c new file mode 100644 index 000000000000..15db9e426ec4 --- /dev/null +++ b/drivers/gpu/drm/aspeed/aspeed_gfx_crtc.c @@ -0,0 +1,241 @@ +// SPDX-License-Identifier: GPL-2.0+ +// Copyright 2018 IBM Corporation + +#include <linux/clk.h> +#include <linux/reset.h> +#include <linux/regmap.h> + +#include <drm/drm_crtc_helper.h> +#include <drm/drm_device.h> +#include <drm/drm_fb_cma_helper.h> +#include <drm/drm_fourcc.h> +#include <drm/drm_gem_cma_helper.h> +#include <drm/drm_gem_framebuffer_helper.h> +#include <drm/drm_panel.h> +#include <drm/drm_simple_kms_helper.h> +#include <drm/drm_vblank.h> + +#include "aspeed_gfx.h" + +static struct aspeed_gfx * +drm_pipe_to_aspeed_gfx(struct drm_simple_display_pipe *pipe) +{ + return container_of(pipe, struct aspeed_gfx, pipe); +} + +static int aspeed_gfx_set_pixel_fmt(struct aspeed_gfx *priv, u32 *bpp) +{ + struct drm_crtc *crtc = &priv->pipe.crtc; + struct drm_device *drm = crtc->dev; + const u32 format = crtc->primary->state->fb->format->format; + u32 ctrl1; + + ctrl1 = readl(priv->base + CRT_CTRL1); + ctrl1 &= ~CRT_CTRL_COLOR_MASK; + + switch (format) { + case DRM_FORMAT_RGB565: + dev_dbg(drm->dev, "Setting up RGB565 mode\n"); + ctrl1 |= CRT_CTRL_COLOR_RGB565; + *bpp = 16; + break; + case DRM_FORMAT_XRGB8888: + dev_dbg(drm->dev, "Setting up XRGB8888 mode\n"); + ctrl1 |= CRT_CTRL_COLOR_XRGB8888; + *bpp = 32; + break; + default: + dev_err(drm->dev, "Unhandled pixel format %08x\n", format); + return -EINVAL; + } + + writel(ctrl1, priv->base + CRT_CTRL1); + + return 0; +} + +static void aspeed_gfx_enable_controller(struct aspeed_gfx *priv) +{ + u32 ctrl1 = readl(priv->base + CRT_CTRL1); + u32 ctrl2 = readl(priv->base + CRT_CTRL2); + + /* SCU2C: set DAC source for display output to Graphics CRT (GFX) */ + regmap_update_bits(priv->scu, 0x2c, BIT(16), BIT(16)); + + writel(ctrl1 | CRT_CTRL_EN, priv->base + CRT_CTRL1); + writel(ctrl2 | CRT_CTRL_DAC_EN, priv->base + CRT_CTRL2); +} + +static void aspeed_gfx_disable_controller(struct aspeed_gfx *priv) +{ + u32 ctrl1 = readl(priv->base + CRT_CTRL1); + u32 ctrl2 = readl(priv->base + CRT_CTRL2); + + writel(ctrl1 & ~CRT_CTRL_EN, priv->base + CRT_CTRL1); + writel(ctrl2 & ~CRT_CTRL_DAC_EN, priv->base + CRT_CTRL2); + + regmap_update_bits(priv->scu, 0x2c, BIT(16), 0); +} + +static void aspeed_gfx_crtc_mode_set_nofb(struct aspeed_gfx *priv) +{ + struct drm_display_mode *m = &priv->pipe.crtc.state->adjusted_mode; + u32 ctrl1, d_offset, t_count, bpp; + int err; + + err = aspeed_gfx_set_pixel_fmt(priv, &bpp); + if (err) + return; + +#if 0 + /* TODO: we have only been able to test with the 40MHz USB clock. The + * clock is fixed, so we cannot adjust it here. */ + clk_set_rate(priv->pixel_clk, m->crtc_clock * 1000); +#endif + + ctrl1 = readl(priv->base + CRT_CTRL1); + ctrl1 &= ~(CRT_CTRL_INTERLACED | + CRT_CTRL_HSYNC_NEGATIVE | + CRT_CTRL_VSYNC_NEGATIVE); + + if (m->flags & DRM_MODE_FLAG_INTERLACE) + ctrl1 |= CRT_CTRL_INTERLACED; + + if (!(m->flags & DRM_MODE_FLAG_PHSYNC)) + ctrl1 |= CRT_CTRL_HSYNC_NEGATIVE; + + if (!(m->flags & DRM_MODE_FLAG_PVSYNC)) + ctrl1 |= CRT_CTRL_VSYNC_NEGATIVE; + + writel(ctrl1, priv->base + CRT_CTRL1); + + /* Horizontal timing */ + writel(CRT_H_TOTAL(m->htotal - 1) | CRT_H_DE(m->hdisplay - 1), + priv->base + CRT_HORIZ0); + writel(CRT_H_RS_START(m->hsync_start - 1) | CRT_H_RS_END(m->hsync_end), + priv->base + CRT_HORIZ1); + + + /* Vertical timing */ + writel(CRT_V_TOTAL(m->vtotal - 1) | CRT_V_DE(m->vdisplay - 1), + priv->base + CRT_VERT0); + writel(CRT_V_RS_START(m->vsync_start) | CRT_V_RS_END(m->vsync_end), + priv->base + CRT_VERT1); + + /* + * Display Offset: address difference between consecutive scan lines + * Terminal Count: memory size of one scan line + */ + d_offset = m->hdisplay * bpp / 8; + t_count = (m->hdisplay * bpp + 127) / 128; + writel(CRT_DISP_OFFSET(d_offset) | CRT_TERM_COUNT(t_count), + priv->base + CRT_OFFSET); + + /* + * Threshold: FIFO thresholds of refill and stop (16 byte chunks + * per line, rounded up) + */ + writel(G5_CRT_THROD_VAL, priv->base + CRT_THROD); +} + +static void aspeed_gfx_pipe_enable(struct drm_simple_display_pipe *pipe, + struct drm_crtc_state *crtc_state, + struct drm_plane_state *plane_state) +{ + struct aspeed_gfx *priv = drm_pipe_to_aspeed_gfx(pipe); + struct drm_crtc *crtc = &pipe->crtc; + + aspeed_gfx_crtc_mode_set_nofb(priv); + aspeed_gfx_enable_controller(priv); + drm_crtc_vblank_on(crtc); +} + +static void aspeed_gfx_pipe_disable(struct drm_simple_display_pipe *pipe) +{ + struct aspeed_gfx *priv = drm_pipe_to_aspeed_gfx(pipe); + struct drm_crtc *crtc = &pipe->crtc; + + drm_crtc_vblank_off(crtc); + aspeed_gfx_disable_controller(priv); +} + +static void aspeed_gfx_pipe_update(struct drm_simple_display_pipe *pipe, + struct drm_plane_state *plane_state) +{ + struct aspeed_gfx *priv = drm_pipe_to_aspeed_gfx(pipe); + struct drm_crtc *crtc = &pipe->crtc; + struct drm_framebuffer *fb = pipe->plane.state->fb; + struct drm_pending_vblank_event *event; + struct drm_gem_cma_object *gem; + + spin_lock_irq(&crtc->dev->event_lock); + event = crtc->state->event; + if (event) { + crtc->state->event = NULL; + + if (drm_crtc_vblank_get(crtc) == 0) + drm_crtc_arm_vblank_event(crtc, event); + else + drm_crtc_send_vblank_event(crtc, event); + } + spin_unlock_irq(&crtc->dev->event_lock); + + if (!fb) + return; + + gem = drm_fb_cma_get_gem_obj(fb, 0); + if (!gem) + return; + writel(gem->paddr, priv->base + CRT_ADDR); +} + +static int aspeed_gfx_enable_vblank(struct drm_simple_display_pipe *pipe) +{ + struct aspeed_gfx *priv = drm_pipe_to_aspeed_gfx(pipe); + u32 reg = readl(priv->base + CRT_CTRL1); + + /* Clear pending VBLANK IRQ */ + writel(reg | CRT_CTRL_VERTICAL_INTR_STS, priv->base + CRT_CTRL1); + + reg |= CRT_CTRL_VERTICAL_INTR_EN; + writel(reg, priv->base + CRT_CTRL1); + + return 0; +} + +static void aspeed_gfx_disable_vblank(struct drm_simple_display_pipe *pipe) +{ + struct aspeed_gfx *priv = drm_pipe_to_aspeed_gfx(pipe); + u32 reg = readl(priv->base + CRT_CTRL1); + + reg &= ~CRT_CTRL_VERTICAL_INTR_EN; + writel(reg, priv->base + CRT_CTRL1); + + /* Clear pending VBLANK IRQ */ + writel(reg | CRT_CTRL_VERTICAL_INTR_STS, priv->base + CRT_CTRL1); +} + +static struct drm_simple_display_pipe_funcs aspeed_gfx_funcs = { + .enable = aspeed_gfx_pipe_enable, + .disable = aspeed_gfx_pipe_disable, + .update = aspeed_gfx_pipe_update, + .prepare_fb = drm_gem_fb_simple_display_pipe_prepare_fb, + .enable_vblank = aspeed_gfx_enable_vblank, + .disable_vblank = aspeed_gfx_disable_vblank, +}; + +static const uint32_t aspeed_gfx_formats[] = { + DRM_FORMAT_XRGB8888, + DRM_FORMAT_RGB565, +}; + +int aspeed_gfx_create_pipe(struct drm_device *drm) +{ + struct aspeed_gfx *priv = drm->dev_private; + + return drm_simple_display_pipe_init(drm, &priv->pipe, &aspeed_gfx_funcs, + aspeed_gfx_formats, + ARRAY_SIZE(aspeed_gfx_formats), + NULL, + &priv->connector); +} diff --git a/drivers/gpu/drm/aspeed/aspeed_gfx_drv.c b/drivers/gpu/drm/aspeed/aspeed_gfx_drv.c new file mode 100644 index 000000000000..eeb22eccd1fc --- /dev/null +++ b/drivers/gpu/drm/aspeed/aspeed_gfx_drv.c @@ -0,0 +1,269 @@ +// SPDX-License-Identifier: GPL-2.0+ +// Copyright 2018 IBM Corporation + +#include <linux/clk.h> +#include <linux/dma-mapping.h> +#include <linux/irq.h> +#include <linux/mfd/syscon.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_reserved_mem.h> +#include <linux/platform_device.h> +#include <linux/regmap.h> +#include <linux/reset.h> + +#include <drm/drm_atomic_helper.h> +#include <drm/drm_crtc_helper.h> +#include <drm/drm_device.h> +#include <drm/drm_fb_cma_helper.h> +#include <drm/drm_fb_helper.h> +#include <drm/drm_gem_cma_helper.h> +#include <drm/drm_gem_framebuffer_helper.h> +#include <drm/drm_probe_helper.h> +#include <drm/drm_simple_kms_helper.h> +#include <drm/drm_vblank.h> +#include <drm/drm_drv.h> + +#include "aspeed_gfx.h" + +/** + * DOC: ASPEED GFX Driver + * + * This driver is for the ASPEED BMC SoC's 'GFX' display hardware, also called + * the 'SOC Display Controller' in the datasheet. This driver runs on the ARM + * based BMC systems, unlike the ast driver which runs on a host CPU and is for + * a PCIe graphics device. + * + * The AST2500 supports a total of 3 output paths: + * + * 1. VGA output, the output target can choose either or both to the DAC + * or DVO interface. + * + * 2. Graphics CRT output, the output target can choose either or both to + * the DAC or DVO interface. + * + * 3. Video input from DVO, the video input can be used for video engine + * capture or DAC display output. + * + * Output options are selected in SCU2C. + * + * The "VGA mode" device is the PCI attached controller. The "Graphics CRT" + * is the ARM's internal display controller. + * + * The driver only supports a simple configuration consisting of a 40MHz + * pixel clock, fixed by hardware limitations, and the VGA output path. + * + * The driver was written with the 'AST2500 Software Programming Guide' v17, + * which is available under NDA from ASPEED. + */ + +static const struct drm_mode_config_funcs aspeed_gfx_mode_config_funcs = { + .fb_create = drm_gem_fb_create, + .atomic_check = drm_atomic_helper_check, + .atomic_commit = drm_atomic_helper_commit, +}; + +static void aspeed_gfx_setup_mode_config(struct drm_device *drm) +{ + drm_mode_config_init(drm); + + drm->mode_config.min_width = 0; + drm->mode_config.min_height = 0; + drm->mode_config.max_width = 800; + drm->mode_config.max_height = 600; + drm->mode_config.funcs = &aspeed_gfx_mode_config_funcs; +} + +static irqreturn_t aspeed_gfx_irq_handler(int irq, void *data) +{ + struct drm_device *drm = data; + struct aspeed_gfx *priv = drm->dev_private; + u32 reg; + + reg = readl(priv->base + CRT_CTRL1); + + if (reg & CRT_CTRL_VERTICAL_INTR_STS) { + drm_crtc_handle_vblank(&priv->pipe.crtc); + writel(reg, priv->base + CRT_CTRL1); + return IRQ_HANDLED; + } + + return IRQ_NONE; +} + + + +static int aspeed_gfx_load(struct drm_device *drm) +{ + struct platform_device *pdev = to_platform_device(drm->dev); + struct aspeed_gfx *priv; + struct resource *res; + int ret; + + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + drm->dev_private = priv; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + priv->base = devm_ioremap_resource(drm->dev, res); + if (IS_ERR(priv->base)) + return PTR_ERR(priv->base); + + priv->scu = syscon_regmap_lookup_by_compatible("aspeed,ast2500-scu"); + if (IS_ERR(priv->scu)) { + dev_err(&pdev->dev, "failed to find SCU regmap\n"); + return PTR_ERR(priv->scu); + } + + ret = of_reserved_mem_device_init(drm->dev); + if (ret) { + dev_err(&pdev->dev, + "failed to initialize reserved mem: %d\n", ret); + return ret; + } + + ret = dma_set_mask_and_coherent(drm->dev, DMA_BIT_MASK(32)); + if (ret) { + dev_err(&pdev->dev, "failed to set DMA mask: %d\n", ret); + return ret; + } + + priv->rst = devm_reset_control_get_exclusive(&pdev->dev, NULL); + if (IS_ERR(priv->rst)) { + dev_err(&pdev->dev, + "missing or invalid reset controller device tree entry"); + return PTR_ERR(priv->rst); + } + reset_control_deassert(priv->rst); + + priv->clk = devm_clk_get(drm->dev, NULL); + if (IS_ERR(priv->clk)) { + dev_err(&pdev->dev, + "missing or invalid clk device tree entry"); + return PTR_ERR(priv->clk); + } + clk_prepare_enable(priv->clk); + + /* Sanitize control registers */ + writel(0, priv->base + CRT_CTRL1); + writel(0, priv->base + CRT_CTRL2); + + aspeed_gfx_setup_mode_config(drm); + + ret = drm_vblank_init(drm, 1); + if (ret < 0) { + dev_err(drm->dev, "Failed to initialise vblank\n"); + return ret; + } + + ret = aspeed_gfx_create_output(drm); + if (ret < 0) { + dev_err(drm->dev, "Failed to create outputs\n"); + return ret; + } + + ret = aspeed_gfx_create_pipe(drm); + if (ret < 0) { + dev_err(drm->dev, "Cannot setup simple display pipe\n"); + return ret; + } + + ret = devm_request_irq(drm->dev, platform_get_irq(pdev, 0), + aspeed_gfx_irq_handler, 0, "aspeed gfx", drm); + if (ret < 0) { + dev_err(drm->dev, "Failed to install IRQ handler\n"); + return ret; + } + + drm_mode_config_reset(drm); + + drm_fbdev_generic_setup(drm, 32); + + return 0; +} + +static void aspeed_gfx_unload(struct drm_device *drm) +{ + drm_kms_helper_poll_fini(drm); + drm_mode_config_cleanup(drm); + + drm->dev_private = NULL; +} + +DEFINE_DRM_GEM_CMA_FOPS(fops); + +static struct drm_driver aspeed_gfx_driver = { + .driver_features = DRIVER_GEM | DRIVER_MODESET | + DRIVER_PRIME | DRIVER_ATOMIC, + .gem_create_object = drm_cma_gem_create_object_default_funcs, + .dumb_create = drm_gem_cma_dumb_create, + .prime_handle_to_fd = drm_gem_prime_handle_to_fd, + .prime_fd_to_handle = drm_gem_prime_fd_to_handle, + .gem_prime_import_sg_table = drm_gem_cma_prime_import_sg_table, + .gem_prime_mmap = drm_gem_prime_mmap, + .fops = &fops, + .name = "aspeed-gfx-drm", + .desc = "ASPEED GFX DRM", + .date = "20180319", + .major = 1, + .minor = 0, +}; + +static const struct of_device_id aspeed_gfx_match[] = { + { .compatible = "aspeed,ast2500-gfx" }, + { } +}; + +static int aspeed_gfx_probe(struct platform_device *pdev) +{ + struct drm_device *drm; + int ret; + + drm = drm_dev_alloc(&aspeed_gfx_driver, &pdev->dev); + if (IS_ERR(drm)) + return PTR_ERR(drm); + + ret = aspeed_gfx_load(drm); + if (ret) + goto err_free; + + ret = drm_dev_register(drm, 0); + if (ret) + goto err_unload; + + return 0; + +err_unload: + aspeed_gfx_unload(drm); +err_free: + drm_dev_put(drm); + + return ret; +} + +static int aspeed_gfx_remove(struct platform_device *pdev) +{ + struct drm_device *drm = platform_get_drvdata(pdev); + + drm_dev_unregister(drm); + aspeed_gfx_unload(drm); + drm_dev_put(drm); + + return 0; +} + +static struct platform_driver aspeed_gfx_platform_driver = { + .probe = aspeed_gfx_probe, + .remove = aspeed_gfx_remove, + .driver = { + .name = "aspeed_gfx", + .of_match_table = aspeed_gfx_match, + }, +}; + +module_platform_driver(aspeed_gfx_platform_driver); + +MODULE_AUTHOR("Joel Stanley joel@jms.id.au"); +MODULE_DESCRIPTION("ASPEED BMC DRM/KMS driver"); +MODULE_LICENSE("GPL"); diff --git a/drivers/gpu/drm/aspeed/aspeed_gfx_out.c b/drivers/gpu/drm/aspeed/aspeed_gfx_out.c new file mode 100644 index 000000000000..67ee5fa10055 --- /dev/null +++ b/drivers/gpu/drm/aspeed/aspeed_gfx_out.c @@ -0,0 +1,42 @@ +// SPDX-License-Identifier: GPL-2.0+ +// Copyright 2018 IBM Corporation + +#include <drm/drm_atomic_helper.h> +#include <drm/drm_connector.h> +#include <drm/drm_crtc_helper.h> +#include <drm/drm_probe_helper.h> + +#include "aspeed_gfx.h" + +static int aspeed_gfx_get_modes(struct drm_connector *connector) +{ + return drm_add_modes_noedid(connector, 800, 600); +} + +static const struct +drm_connector_helper_funcs aspeed_gfx_connector_helper_funcs = { + .get_modes = aspeed_gfx_get_modes, +}; + +static const struct drm_connector_funcs aspeed_gfx_connector_funcs = { + .fill_modes = drm_helper_probe_single_connector_modes, + .destroy = drm_connector_cleanup, + .reset = drm_atomic_helper_connector_reset, + .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, + .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, +}; + +int aspeed_gfx_create_output(struct drm_device *drm) +{ + struct aspeed_gfx *priv = drm->dev_private; + int ret; + + priv->connector.dpms = DRM_MODE_DPMS_OFF; + priv->connector.polled = 0; + drm_connector_helper_add(&priv->connector, + &aspeed_gfx_connector_helper_funcs); + ret = drm_connector_init(drm, &priv->connector, + &aspeed_gfx_connector_funcs, + DRM_MODE_CONNECTOR_Unknown); + return ret; +}