The DSI pixel clocks are muxed from clocks generated in the analog phy by the DSI driver. In order to set them as parents, we need to do the same name lookup dance on them as we do for our root oscillator.

Signed-off-by: Eric Anholt eric@anholt.net --- .../bindings/clock/brcm,bcm2835-cprman.txt | 15 ++- drivers/clk/bcm/clk-bcm2835.c | 120 ++++++++++++++++++--- include/dt-bindings/clock/bcm2835.h | 2 + 3 files changed, 124 insertions(+), 13 deletions(-)

diff --git a/Documentation/devicetree/bindings/clock/brcm,bcm2835-cprman.txt b/Documentation/devicetree/bindings/clock/brcm,bcm2835-cprman.txt index e56a1df3a9d3..dd906db34b32 100644 --- a/Documentation/devicetree/bindings/clock/brcm,bcm2835-cprman.txt +++ b/Documentation/devicetree/bindings/clock/brcm,bcm2835-cprman.txt @@ -16,7 +16,20 @@ Required properties: - #clock-cells: Should be <1>. The permitted clock-specifier values can be found in include/dt-bindings/clock/bcm2835.h - reg: Specifies base physical address and size of the registers -- clocks: The external oscillator clock phandle +- clocks: phandles to the parent clocks used as input to the module, in + the following order: + + - External oscillator + - DSI0 byte clock + - DSI0 DDR2 clock + - DSI0 DDR clock + - DSI1 byte clock + - DSI1 DDR2 clock + - DSI1 DDR clock + + Only external oscillator is required. The DSI clocks may + not be present, in which case their children will be + unusable.

Example:

diff --git a/drivers/clk/bcm/clk-bcm2835.c b/drivers/clk/bcm/clk-bcm2835.c index 6641030e8eae..b0a8cd19a30c 100644 --- a/drivers/clk/bcm/clk-bcm2835.c +++ b/drivers/clk/bcm/clk-bcm2835.c @@ -297,11 +297,32 @@ #define LOCK_TIMEOUT_NS 100000000 #define BCM2835_MAX_FB_RATE 1750000000u

+/* + * Names of clocks used within the driver that need to be replaced + * with an external parent's name. This array is in the order that + * the clocks node in the DT references external clocks. + */ +static const char *const cprman_parent_names[] = { + "xosc", + "dsi0_byte", + "dsi0_ddr2", + "dsi0_ddr", + "dsi1_byte", + "dsi1_ddr2", + "dsi1_ddr", +}; + struct bcm2835_cprman { struct device *dev; void __iomem *regs; spinlock_t regs_lock; /* spinlock for all clocks */ - const char *osc_name; + + /* + * Real names of cprman clock parents looked up through + * of_clk_get_parent_name(), which will be used in the + * parent_names[] arrays for clock registration. + */ + const char *real_parent_names[ARRAY_SIZE(cprman_parent_names)];

/* Must be last */ struct clk_hw_onecell_data onecell; @@ -905,6 +926,9 @@ static long bcm2835_clock_rate_from_divisor(struct bcm2835_clock *clock, const struct bcm2835_clock_data *data = clock->data; u64 temp;

+ if (data->int_bits == 0 && data->frac_bits == 0) + return parent_rate; + /* * The divisor is a 12.12 fixed point field, but only some of * the bits are populated in any given clock. @@ -928,7 +952,12 @@ static unsigned long bcm2835_clock_get_rate(struct clk_hw *hw, struct bcm2835_clock *clock = bcm2835_clock_from_hw(hw); struct bcm2835_cprman *cprman = clock->cprman; const struct bcm2835_clock_data *data = clock->data; - u32 div = cprman_read(cprman, data->div_reg); + u32 div; + + if (data->int_bits == 0 && data->frac_bits == 0) + return parent_rate; + + div = cprman_read(cprman, data->div_reg);

return bcm2835_clock_rate_from_divisor(clock, parent_rate, div); } @@ -1158,7 +1187,7 @@ static struct clk_hw *bcm2835_register_pll(struct bcm2835_cprman *cprman, memset(&init, 0, sizeof(init));

/* All of the PLLs derive from the external oscillator. */ - init.parent_names = &cprman->osc_name; + init.parent_names = &cprman->real_parent_names[0]; init.num_parents = 1; init.name = data->name; init.ops = &bcm2835_pll_clk_ops; @@ -1244,18 +1273,22 @@ static struct clk_hw *bcm2835_register_clock(struct bcm2835_cprman *cprman, struct bcm2835_clock *clock; struct clk_init_data init; const char *parents[1 << CM_SRC_BITS]; - size_t i; + size_t i, j; int ret;

/* - * Replace our "xosc" references with the oscillator's - * actual name. + * Replace our strings referencing parent clocks with the + * actual clock-output-name of the parent. */ for (i = 0; i < data->num_mux_parents; i++) { - if (strcmp(data->parents[i], "xosc") == 0) - parents[i] = cprman->osc_name; - else - parents[i] = data->parents[i]; + parents[i] = data->parents[i]; + + for (j = 0; j < ARRAY_SIZE(cprman_parent_names); j++) { + if (strcmp(parents[i], cprman_parent_names[j]) == 0) { + parents[i] = cprman->real_parent_names[j]; + break; + } + } }

memset(&init, 0, sizeof(init)); @@ -1375,6 +1408,47 @@ static const char *const bcm2835_clock_vpu_parents[] = { __VA_ARGS__)

/* + * DSI parent clocks. The DSI byte/DDR/DDR2 clocks come from the DSI + * analog PHY. The _inv variants are generated internally to cprman, + * but we don't use them so they aren't hooked up. + */ +static const char *const bcm2835_clock_dsi0_parents[] = { + "gnd", + "xosc", + "testdebug0", + "testdebug1", + "dsi0_ddr", + "dsi0_ddr_inv", + "dsi0_ddr2", + "dsi0_ddr2_inv", + "dsi0_byte", + "dsi0_byte_inv", +}; + +static const char *const bcm2835_clock_dsi1_parents[] = { + "gnd", + "xosc", + "testdebug0", + "testdebug1", + "dsi1_ddr", + "dsi1_ddr_inv", + "dsi1_ddr2", + "dsi1_ddr2_inv", + "dsi1_byte", + "dsi1_byte_inv", +}; + +#define REGISTER_DSI0_CLK(...) REGISTER_CLK( \ + .num_mux_parents = ARRAY_SIZE(bcm2835_clock_dsi0_parents), \ + .parents = bcm2835_clock_dsi0_parents, \ + __VA_ARGS__) + +#define REGISTER_DSI1_CLK(...) REGISTER_CLK( \ + .num_mux_parents = ARRAY_SIZE(bcm2835_clock_dsi1_parents), \ + .parents = bcm2835_clock_dsi1_parents, \ + __VA_ARGS__) + +/* * the real definition of all the pll, pll_dividers and clocks * these make use of the above REGISTER_* macros */ @@ -1832,6 +1906,18 @@ static const struct bcm2835_clk_desc clk_desc_array[] = { .div_reg = CM_DSI1EDIV, .int_bits = 4, .frac_bits = 8), + [BCM2835_CLOCK_DSI0P] = REGISTER_DSI0_CLK( + .name = "dsi0p", + .ctl_reg = CM_DSI0PCTL, + .div_reg = CM_DSI0PDIV, + .int_bits = 0, + .frac_bits = 0), + [BCM2835_CLOCK_DSI1P] = REGISTER_DSI1_CLK( + .name = "dsi1p", + .ctl_reg = CM_DSI1PCTL, + .div_reg = CM_DSI1PDIV, + .int_bits = 0, + .frac_bits = 0),

/* the gates */

@@ -1890,8 +1976,18 @@ static int bcm2835_clk_probe(struct platform_device *pdev) if (IS_ERR(cprman->regs)) return PTR_ERR(cprman->regs);

- cprman->osc_name = of_clk_get_parent_name(dev->of_node, 0); - if (!cprman->osc_name) + for (i = 0; i < ARRAY_SIZE(cprman_parent_names); i++) { + cprman->real_parent_names[i] = + of_clk_get_parent_name(dev->of_node, i); + } + /* + * Make sure the external oscillator has been registered. + * + * The other (DSI) clocks are not present on older device + * trees, which we still need to support for backwards + * compatibility. + */ + if (!cprman->real_parent_names[0]) return -ENODEV;

platform_set_drvdata(pdev, cprman); diff --git a/include/dt-bindings/clock/bcm2835.h b/include/dt-bindings/clock/bcm2835.h index 360e00cefd35..a0c812b0fa39 100644 --- a/include/dt-bindings/clock/bcm2835.h +++ b/include/dt-bindings/clock/bcm2835.h @@ -64,3 +64,5 @@ #define BCM2835_CLOCK_CAM1 46 #define BCM2835_CLOCK_DSI0E 47 #define BCM2835_CLOCK_DSI1E 48 +#define BCM2835_CLOCK_DSI0P 49 +#define BCM2835_CLOCK_DSI1P 50

We want the HVS on, obviously, and we also want DSP3 (PV1's source) to be muxed from HVS channel 2 like we expect in vc4_crtc.c. The firmware wasn't setting the DSP3 mux up when both the LCD and HDMI were disabled.

Signed-off-by: Eric Anholt eric@anholt.net --- drivers/gpu/drm/vc4/vc4_hvs.c | 14 ++++++++++++++ drivers/gpu/drm/vc4/vc4_regs.h | 3 +++ 2 files changed, 17 insertions(+)

diff --git a/drivers/gpu/drm/vc4/vc4_hvs.c b/drivers/gpu/drm/vc4/vc4_hvs.c index 6fbab1c82cb1..fc68b1b4da52 100644 --- a/drivers/gpu/drm/vc4/vc4_hvs.c +++ b/drivers/gpu/drm/vc4/vc4_hvs.c @@ -170,6 +170,7 @@ static int vc4_hvs_bind(struct device *dev, struct device *master, void *data) struct vc4_dev *vc4 = drm->dev_private; struct vc4_hvs *hvs = NULL; int ret; + u32 dispctrl;

hvs = devm_kzalloc(&pdev->dev, sizeof(*hvs), GFP_KERNEL); if (!hvs) @@ -211,6 +212,19 @@ static int vc4_hvs_bind(struct device *dev, struct device *master, void *data) return ret;

vc4->hvs = hvs; + + dispctrl = HVS_READ(SCALER_DISPCTRL); + + dispctrl |= SCALER_DISPCTRL_ENABLE; + + /* Set DSP3 (PV1) to use HVS channel 2, which would otherwise + * be unused. + */ + dispctrl &= ~SCALER_DISPCTRL_DSP3_MUX_MASK; + dispctrl |= VC4_SET_FIELD(2, SCALER_DISPCTRL_DSP3_MUX); + + HVS_WRITE(SCALER_DISPCTRL, dispctrl); + return 0; }

diff --git a/drivers/gpu/drm/vc4/vc4_regs.h b/drivers/gpu/drm/vc4/vc4_regs.h index 39f6886b2410..b3b297fba709 100644 --- a/drivers/gpu/drm/vc4/vc4_regs.h +++ b/drivers/gpu/drm/vc4/vc4_regs.h @@ -244,6 +244,9 @@ # define SCALER_DISPCTRL_ENABLE BIT(31) # define SCALER_DISPCTRL_DSP2EISLUR BIT(15) # define SCALER_DISPCTRL_DSP1EISLUR BIT(14) +# define SCALER_DISPCTRL_DSP3_MUX_MASK VC4_MASK(19, 18) +# define SCALER_DISPCTRL_DSP3_MUX_SHIFT 18 + /* Enables Display 0 short line and underrun contribution to * SCALER_DISPSTAT_IRQDISP0. Note that short frame contributions are * always enabled.

We have to set a different pixel format, which tells the hardware to use the pix_width field that's fed in sideband from the DSI encoder to divide the "pixel" clock.

Signed-off-by: Eric Anholt eric@anholt.net --- drivers/gpu/drm/vc4/vc4_crtc.c | 33 +++++++++++++++++++-------------- drivers/gpu/drm/vc4/vc4_regs.h | 2 ++ 2 files changed, 21 insertions(+), 14 deletions(-)

diff --git a/drivers/gpu/drm/vc4/vc4_crtc.c b/drivers/gpu/drm/vc4/vc4_crtc.c index a0fd3e66bc4b..cd070e0c79a6 100644 --- a/drivers/gpu/drm/vc4/vc4_crtc.c +++ b/drivers/gpu/drm/vc4/vc4_crtc.c @@ -349,38 +349,40 @@ static u32 vc4_get_fifo_full_level(u32 format) }

/* - * Returns the clock select bit for the connector attached to the - * CRTC. + * Returns the encoder attached to the CRTC. + * + * VC4 can only scan out to one encoder at a time, while the DRM core + * allows drivers to push pixels to more than one encoder from the + * same CRTC. */ -static int vc4_get_clock_select(struct drm_crtc *crtc) +static struct drm_encoder *vc4_get_crtc_encoder(struct drm_crtc *crtc) { struct drm_connector *connector;

drm_for_each_connector(connector, crtc->dev) { if (connector->state->crtc == crtc) { - struct drm_encoder *encoder = connector->encoder; - struct vc4_encoder *vc4_encoder = - to_vc4_encoder(encoder); - - return vc4_encoder->clock_select; + return connector->encoder; } }

- return -1; + return NULL; }

static void vc4_crtc_mode_set_nofb(struct drm_crtc *crtc) { struct drm_device *dev = crtc->dev; struct vc4_dev *vc4 = to_vc4_dev(dev); + struct drm_encoder *encoder = vc4_get_crtc_encoder(crtc); + struct vc4_encoder *vc4_encoder = to_vc4_encoder(encoder); struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc); struct drm_crtc_state *state = crtc->state; struct drm_display_mode *mode = &state->adjusted_mode; bool interlace = mode->flags & DRM_MODE_FLAG_INTERLACE; u32 pixel_rep = (mode->flags & DRM_MODE_FLAG_DBLCLK) ? 2 : 1; - u32 format = PV_CONTROL_FORMAT_24; + bool is_dsi = (vc4_encoder->type == VC4_ENCODER_TYPE_DSI0 || + vc4_encoder->type == VC4_ENCODER_TYPE_DSI1); + u32 format = is_dsi ? PV_CONTROL_FORMAT_DSIV_24 : PV_CONTROL_FORMAT_24; bool debug_dump_regs = false; - int clock_select = vc4_get_clock_select(crtc);

if (debug_dump_regs) { DRM_INFO("CRTC %d regs before:\n", drm_crtc_index(crtc)); @@ -436,17 +438,19 @@ static void vc4_crtc_mode_set_nofb(struct drm_crtc *crtc) */ CRTC_WRITE(PV_V_CONTROL, PV_VCONTROL_CONTINUOUS | + (is_dsi ? PV_VCONTROL_DSI : 0) | PV_VCONTROL_INTERLACE | VC4_SET_FIELD(mode->htotal * pixel_rep / 2, PV_VCONTROL_ODD_DELAY)); CRTC_WRITE(PV_VSYNCD_EVEN, 0); } else { - CRTC_WRITE(PV_V_CONTROL, PV_VCONTROL_CONTINUOUS); + CRTC_WRITE(PV_V_CONTROL, + PV_VCONTROL_CONTINUOUS | + (is_dsi ? PV_VCONTROL_DSI : 0)); }

CRTC_WRITE(PV_HACT_ACT, mode->hdisplay * pixel_rep);

- CRTC_WRITE(PV_CONTROL, VC4_SET_FIELD(format, PV_CONTROL_FORMAT) | VC4_SET_FIELD(vc4_get_fifo_full_level(format), @@ -455,7 +459,8 @@ static void vc4_crtc_mode_set_nofb(struct drm_crtc *crtc) PV_CONTROL_CLR_AT_START | PV_CONTROL_TRIGGER_UNDERFLOW | PV_CONTROL_WAIT_HSTART | - VC4_SET_FIELD(clock_select, PV_CONTROL_CLK_SELECT) | + VC4_SET_FIELD(vc4_encoder->clock_select, + PV_CONTROL_CLK_SELECT) | PV_CONTROL_FIFO_CLR | PV_CONTROL_EN);

diff --git a/drivers/gpu/drm/vc4/vc4_regs.h b/drivers/gpu/drm/vc4/vc4_regs.h index b3b297fba709..385405a2df05 100644 --- a/drivers/gpu/drm/vc4/vc4_regs.h +++ b/drivers/gpu/drm/vc4/vc4_regs.h @@ -190,6 +190,8 @@ # define PV_VCONTROL_ODD_DELAY_SHIFT 6 # define PV_VCONTROL_ODD_FIRST BIT(5) # define PV_VCONTROL_INTERLACE BIT(4) +# define PV_VCONTROL_DSI BIT(3) +# define PV_VCONTROL_COMMAND BIT(2) # define PV_VCONTROL_CONTINUOUS BIT(1) # define PV_VCONTROL_VIDEN BIT(0)

The DSI0 and DSI1 blocks on the 2835 are related hardware blocks. Some registers move around, and the featureset is slightly different, as DSI1 (the 4-lane DSI) is a later version of the hardware block. This driver doesn't yet enable DSI0, since we don't have any hardware to test against, but it does put a lot of the register definitions and code in place.

Signed-off-by: Eric Anholt eric@anholt.net --- drivers/gpu/drm/vc4/Kconfig | 2 + drivers/gpu/drm/vc4/Makefile | 1 + drivers/gpu/drm/vc4/vc4_debugfs.c | 1 + drivers/gpu/drm/vc4/vc4_drv.c | 1 + drivers/gpu/drm/vc4/vc4_drv.h | 5 + drivers/gpu/drm/vc4/vc4_dsi.c | 1725 +++++++++++++++++++++++++++++++++++++ 6 files changed, 1735 insertions(+) create mode 100644 drivers/gpu/drm/vc4/vc4_dsi.c

diff --git a/drivers/gpu/drm/vc4/Kconfig b/drivers/gpu/drm/vc4/Kconfig index e53df59cb139..e1517d07cb7d 100644 --- a/drivers/gpu/drm/vc4/Kconfig +++ b/drivers/gpu/drm/vc4/Kconfig @@ -2,10 +2,12 @@ config DRM_VC4 tristate "Broadcom VC4 Graphics" depends on ARCH_BCM2835 || COMPILE_TEST depends on DRM + depends on COMMON_CLK select DRM_KMS_HELPER select DRM_KMS_CMA_HELPER select DRM_GEM_CMA_HELPER select DRM_PANEL + select DRM_MIPI_DSI help Choose this option if you have a system that has a Broadcom VC4 GPU, such as the Raspberry Pi or other BCM2708/BCM2835. diff --git a/drivers/gpu/drm/vc4/Makefile b/drivers/gpu/drm/vc4/Makefile index 7757f69a8a77..61f45d122bd0 100644 --- a/drivers/gpu/drm/vc4/Makefile +++ b/drivers/gpu/drm/vc4/Makefile @@ -8,6 +8,7 @@ vc4-y := \ vc4_crtc.o \ vc4_drv.o \ vc4_dpi.o \ + vc4_dsi.o \ vc4_kms.o \ vc4_gem.o \ vc4_hdmi.o \ diff --git a/drivers/gpu/drm/vc4/vc4_debugfs.c b/drivers/gpu/drm/vc4/vc4_debugfs.c index caf817bac885..3ca476c6e057 100644 --- a/drivers/gpu/drm/vc4/vc4_debugfs.c +++ b/drivers/gpu/drm/vc4/vc4_debugfs.c @@ -18,6 +18,7 @@ static const struct drm_info_list vc4_debugfs_list[] = { {"bo_stats", vc4_bo_stats_debugfs, 0}, {"dpi_regs", vc4_dpi_debugfs_regs, 0}, + {"dsi1_regs", vc4_dsi_debugfs_regs, 0, (void *)(uintptr_t)1}, {"hdmi_regs", vc4_hdmi_debugfs_regs, 0}, {"vec_regs", vc4_vec_debugfs_regs, 0}, {"hvs_regs", vc4_hvs_debugfs_regs, 0}, diff --git a/drivers/gpu/drm/vc4/vc4_drv.c b/drivers/gpu/drm/vc4/vc4_drv.c index bdab333979dc..2d2edc7dcf4a 100644 --- a/drivers/gpu/drm/vc4/vc4_drv.c +++ b/drivers/gpu/drm/vc4/vc4_drv.c @@ -298,6 +298,7 @@ static struct platform_driver *const component_drivers[] = { &vc4_hdmi_driver, &vc4_vec_driver, &vc4_dpi_driver, + &vc4_dsi_driver, &vc4_hvs_driver, &vc4_crtc_driver, &vc4_v3d_driver, diff --git a/drivers/gpu/drm/vc4/vc4_drv.h b/drivers/gpu/drm/vc4/vc4_drv.h index b5c4bb14d0d1..723f0ec940ac 100644 --- a/drivers/gpu/drm/vc4/vc4_drv.h +++ b/drivers/gpu/drm/vc4/vc4_drv.h @@ -17,6 +17,7 @@ struct vc4_dev { struct vc4_crtc *crtc[3]; struct vc4_v3d *v3d; struct vc4_dpi *dpi; + struct vc4_dsi *dsi1; struct vc4_vec *vec;

struct drm_fbdev_cma *fbdev; @@ -465,6 +466,10 @@ void __iomem *vc4_ioremap_regs(struct platform_device *dev, int index); extern struct platform_driver vc4_dpi_driver; int vc4_dpi_debugfs_regs(struct seq_file *m, void *unused);

+/* vc4_dsi.c */ +extern struct platform_driver vc4_dsi_driver; +int vc4_dsi_debugfs_regs(struct seq_file *m, void *unused); + /* vc4_gem.c */ void vc4_gem_init(struct drm_device *dev); void vc4_gem_destroy(struct drm_device *dev); diff --git a/drivers/gpu/drm/vc4/vc4_dsi.c b/drivers/gpu/drm/vc4/vc4_dsi.c new file mode 100644 index 000000000000..17fcac381dbb --- /dev/null +++ b/drivers/gpu/drm/vc4/vc4_dsi.c @@ -0,0 +1,1725 @@ +/* + * Copyright (C) 2016 Broadcom + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see http://www.gnu.org/licenses/. + */ + +/** + * DOC: VC4 DSI0/DSI1 module + * + * BCM2835 contains two DSI modules, DSI0 and DSI1. DSI0 is a + * single-lane DSI controller, while DSI1 is a more modern 4-lane DSI + * controller. + * + * Most Raspberry Pi boards expose DSI1 as their "DISPLAY" connector, + * while the compute module brings both DSI0 and DSI1 out. + * + * This driver has been tested for DSI1 video-mode display only + * currently, with most of the information necessary for DSI0 + * hopefully present. + */ + +#include "drm_atomic_helper.h" +#include "drm_crtc_helper.h" +#include "drm_edid.h" +#include "drm_mipi_dsi.h" +#include "drm_panel.h" +#include "linux/clk.h" +#include "linux/clk-provider.h" +#include "linux/completion.h" +#include "linux/component.h" +#include "linux/dmaengine.h" +#include "linux/i2c.h" +#include "linux/of_address.h" +#include "linux/of_platform.h" +#include "linux/pm_runtime.h" +#include "vc4_drv.h" +#include "vc4_regs.h" + +#define DSI_CMD_FIFO_DEPTH 16 +#define DSI_PIX_FIFO_DEPTH 256 +#define DSI_PIX_FIFO_WIDTH 4 + +#define DSI0_CTRL 0x00 + +/* Command packet control. */ +#define DSI0_TXPKT1C 0x04 /* AKA PKTC */ +#define DSI1_TXPKT1C 0x04 +# define DSI_TXPKT1C_TRIG_CMD_MASK VC4_MASK(31, 24) +# define DSI_TXPKT1C_TRIG_CMD_SHIFT 24 +# define DSI_TXPKT1C_CMD_REPEAT_MASK VC4_MASK(23, 10) +# define DSI_TXPKT1C_CMD_REPEAT_SHIFT 10 + +# define DSI_TXPKT1C_DISPLAY_NO_MASK VC4_MASK(9, 8) +# define DSI_TXPKT1C_DISPLAY_NO_SHIFT 8 +/* Short, trigger, BTA, or a long packet that fits all in CMDFIFO. */ +# define DSI_TXPKT1C_DISPLAY_NO_SHORT 0 +/* Primary display where cmdfifo provides part of the payload and + * pixelvalve the rest. + */ +# define DSI_TXPKT1C_DISPLAY_NO_PRIMARY 1 +/* Secondary display where cmdfifo provides part of the payload and + * pixfifo the rest. + */ +# define DSI_TXPKT1C_DISPLAY_NO_SECONDARY 2 + +# define DSI_TXPKT1C_CMD_TX_TIME_MASK VC4_MASK(7, 6) +# define DSI_TXPKT1C_CMD_TX_TIME_SHIFT 6 + +# define DSI_TXPKT1C_CMD_CTRL_MASK VC4_MASK(5, 4) +# define DSI_TXPKT1C_CMD_CTRL_SHIFT 4 +/* Command only. Uses TXPKT1H and DISPLAY_NO */ +# define DSI_TXPKT1C_CMD_CTRL_TX 0 +/* Command with BTA for either ack or read data. */ +# define DSI_TXPKT1C_CMD_CTRL_RX 1 +/* Trigger according to TRIG_CMD */ +# define DSI_TXPKT1C_CMD_CTRL_TRIG 2 +/* BTA alone for getting error status after a command, or a TE trigger + * without a previous command. + */ +# define DSI_TXPKT1C_CMD_CTRL_BTA 3 + +# define DSI_TXPKT1C_CMD_MODE_LP BIT(3) +# define DSI_TXPKT1C_CMD_TYPE_LONG BIT(2) +# define DSI_TXPKT1C_CMD_TE_EN BIT(1) +# define DSI_TXPKT1C_CMD_EN BIT(0) + +/* Command packet header. */ +#define DSI0_TXPKT1H 0x08 /* AKA PKTH */ +#define DSI1_TXPKT1H 0x08 +# define DSI_TXPKT1H_BC_CMDFIFO_MASK VC4_MASK(31, 24) +# define DSI_TXPKT1H_BC_CMDFIFO_SHIFT 24 +# define DSI_TXPKT1H_BC_PARAM_MASK VC4_MASK(23, 8) +# define DSI_TXPKT1H_BC_PARAM_SHIFT 8 +# define DSI_TXPKT1H_BC_DT_MASK VC4_MASK(7, 0) +# define DSI_TXPKT1H_BC_DT_SHIFT 0 + +#define DSI0_RXPKT1H 0x0c /* AKA RX1_PKTH */ +#define DSI1_RXPKT1H 0x14 +# define DSI_RXPKT1H_CRC_ERR BIT(31) +# define DSI_RXPKT1H_DET_ERR BIT(30) +# define DSI_RXPKT1H_ECC_ERR BIT(29) +# define DSI_RXPKT1H_COR_ERR BIT(28) +# define DSI_RXPKT1H_INCOMP_PKT BIT(25) +# define DSI_RXPKT1H_PKT_TYPE_LONG BIT(24) +/* Byte count if DSI_RXPKT1H_PKT_TYPE_LONG */ +# define DSI_RXPKT1H_BC_PARAM_MASK VC4_MASK(23, 8) +# define DSI_RXPKT1H_BC_PARAM_SHIFT 8 +/* Short return bytes if !DSI_RXPKT1H_PKT_TYPE_LONG */ +# define DSI_RXPKT1H_SHORT_1_MASK VC4_MASK(23, 16) +# define DSI_RXPKT1H_SHORT_1_SHIFT 16 +# define DSI_RXPKT1H_SHORT_0_MASK VC4_MASK(15, 8) +# define DSI_RXPKT1H_SHORT_0_SHIFT 8 +# define DSI_RXPKT1H_DT_LP_CMD_MASK VC4_MASK(7, 0) +# define DSI_RXPKT1H_DT_LP_CMD_SHIFT 0 + +#define DSI0_RXPKT2H 0x10 /* AKA RX2_PKTH */ +#define DSI1_RXPKT2H 0x18 +# define DSI_RXPKT1H_DET_ERR BIT(30) +# define DSI_RXPKT1H_ECC_ERR BIT(29) +# define DSI_RXPKT1H_COR_ERR BIT(28) +# define DSI_RXPKT1H_INCOMP_PKT BIT(25) +# define DSI_RXPKT1H_BC_PARAM_MASK VC4_MASK(23, 8) +# define DSI_RXPKT1H_BC_PARAM_SHIFT 8 +# define DSI_RXPKT1H_DT_MASK VC4_MASK(7, 0) +# define DSI_RXPKT1H_DT_SHIFT 0 + +#define DSI0_TXPKT_CMD_FIFO 0x14 /* AKA CMD_DATAF */ +#define DSI1_TXPKT_CMD_FIFO 0x1c + +#define DSI0_DISP0_CTRL 0x18 +# define DSI_DISP0_PIX_CLK_DIV_MASK VC4_MASK(21, 13) +# define DSI_DISP0_PIX_CLK_DIV_SHIFT 13 +# define DSI_DISP0_LP_STOP_CTRL_MASK VC4_MASK(12, 11) +# define DSI_DISP0_LP_STOP_CTRL_SHIFT 11 +# define DSI_DISP0_LP_STOP_DISABLE 0 +# define DSI_DISP0_LP_STOP_PERLINE 1 +# define DSI_DISP0_LP_STOP_PERFRAME 2 + +/* Transmit RGB pixels and null packets only during HACTIVE, instead + * of going to LP-STOP. + */ +# define DSI_DISP_HACTIVE_NULL BIT(10) +/* Transmit blanking packet only during vblank, instead of allowing LP-STOP. */ +# define DSI_DISP_VBLP_CTRL BIT(9) +/* Transmit blanking packet only during HFP, instead of allowing LP-STOP. */ +# define DSI_DISP_HFP_CTRL BIT(8) +/* Transmit blanking packet only during HBP, instead of allowing LP-STOP. */ +# define DSI_DISP_HBP_CTRL BIT(7) +# define DSI_DISP0_CHANNEL_MASK VC4_MASK(6, 5) +# define DSI_DISP0_CHANNEL_SHIFT 5 +/* Enables end events for HSYNC/VSYNC, not just start events. */ +# define DSI_DISP0_ST_END BIT(4) +# define DSI_DISP0_PFORMAT_MASK VC4_MASK(3, 2) +# define DSI_DISP0_PFORMAT_SHIFT 2 +# define DSI_PFORMAT_RGB565 0 +# define DSI_PFORMAT_RGB666_PACKED 1 +# define DSI_PFORMAT_RGB666 2 +# define DSI_PFORMAT_RGB888 3 +/* Default is VIDEO mode. */ +# define DSI_DISP0_COMMAND_MODE BIT(1) +# define DSI_DISP0_ENABLE BIT(0) + +#define DSI0_DISP1_CTRL 0x1c +#define DSI1_DISP1_CTRL 0x2c +/* Format of the data written to TXPKT_PIX_FIFO. */ +# define DSI_DISP1_PFORMAT_MASK VC4_MASK(2, 1) +# define DSI_DISP1_PFORMAT_SHIFT 1 +# define DSI_DISP1_PFORMAT_16BIT 0 +# define DSI_DISP1_PFORMAT_24BIT 1 +# define DSI_DISP1_PFORMAT_32BIT_LE 2 +# define DSI_DISP1_PFORMAT_32BIT_BE 3 + +/* DISP1 is always command mode. */ +# define DSI_DISP1_ENABLE BIT(0) + +#define DSI0_TXPKT_PIX_FIFO 0x20 /* AKA PIX_FIFO */ + +#define DSI0_INT_STAT 0x24 +#define DSI0_INT_EN 0x28 +# define DSI1_INT_PHY_D3_ULPS BIT(30) +# define DSI1_INT_PHY_D3_STOP BIT(29) +# define DSI1_INT_PHY_D2_ULPS BIT(28) +# define DSI1_INT_PHY_D2_STOP BIT(27) +# define DSI1_INT_PHY_D1_ULPS BIT(26) +# define DSI1_INT_PHY_D1_STOP BIT(25) +# define DSI1_INT_PHY_D0_ULPS BIT(24) +# define DSI1_INT_PHY_D0_STOP BIT(23) +# define DSI1_INT_FIFO_ERR BIT(22) +# define DSI1_INT_PHY_DIR_RTF BIT(21) +# define DSI1_INT_PHY_RXLPDT BIT(20) +# define DSI1_INT_PHY_RXTRIG BIT(19) +# define DSI1_INT_PHY_D0_LPDT BIT(18) +# define DSI1_INT_PHY_DIR_FTR BIT(17) + +/* Signaled when the clock lane enters the given state. */ +# define DSI1_INT_PHY_CLOCK_ULPS BIT(16) +# define DSI1_INT_PHY_CLOCK_HS BIT(15) +# define DSI1_INT_PHY_CLOCK_STOP BIT(14) + +/* Signaled on timeouts */ +# define DSI1_INT_PR_TO BIT(13) +# define DSI1_INT_TA_TO BIT(12) +# define DSI1_INT_LPRX_TO BIT(11) +# define DSI1_INT_HSTX_TO BIT(10) + +/* Contention on a line when trying to drive the line low */ +# define DSI1_INT_ERR_CONT_LP1 BIT(9) +# define DSI1_INT_ERR_CONT_LP0 BIT(8) + +/* Control error: incorrect line state sequence on data lane 0. */ +# define DSI1_INT_ERR_CONTROL BIT(7) +/* LPDT synchronization error (bits received not a multiple of 8. */ + +# define DSI1_INT_ERR_SYNC_ESC BIT(6) +/* Signaled after receiving an error packet from the display in + * response to a read. + */ +# define DSI1_INT_RXPKT2 BIT(5) +/* Signaled after receiving a packet. The header and optional short + * response will be in RXPKT1H, and a long response will be in the + * RXPKT_FIFO. + */ +# define DSI1_INT_RXPKT1 BIT(4) +# define DSI1_INT_TXPKT2_DONE BIT(3) +# define DSI1_INT_TXPKT2_END BIT(2) +/* Signaled after all repeats of TXPKT1 are transferred. */ +# define DSI1_INT_TXPKT1_DONE BIT(1) +/* Signaled after each TXPKT1 repeat is scheduled. */ +# define DSI1_INT_TXPKT1_END BIT(0) + +#define DSI1_INTERRUPTS_ALWAYS_ENABLED (DSI1_INT_ERR_SYNC_ESC | \ + DSI1_INT_ERR_CONTROL | \ + DSI1_INT_ERR_CONT_LP0 | \ + DSI1_INT_ERR_CONT_LP1 | \ + DSI1_INT_HSTX_TO | \ + DSI1_INT_LPRX_TO | \ + DSI1_INT_TA_TO | \ + DSI1_INT_PR_TO) + +#define DSI0_STAT 0x2c +#define DSI0_HSTX_TO_CNT 0x30 +#define DSI0_LPRX_TO_CNT 0x34 +#define DSI0_TA_TO_CNT 0x38 +#define DSI0_PR_TO_CNT 0x3c +#define DSI0_PHYC 0x40 +# define DSI1_PHYC_ESC_CLK_LPDT_MASK VC4_MASK(25, 20) +# define DSI1_PHYC_ESC_CLK_LPDT_SHIFT 20 +# define DSI1_PHYC_HS_CLK_CONTINUOUS BIT(18) +# define DSI0_PHYC_ESC_CLK_LPDT_MASK VC4_MASK(17, 12) +# define DSI0_PHYC_ESC_CLK_LPDT_SHIFT 12 +# define DSI1_PHYC_CLANE_ULPS BIT(17) +# define DSI1_PHYC_CLANE_ENABLE BIT(16) +# define DSI_PHYC_DLANE3_ULPS BIT(13) +# define DSI_PHYC_DLANE3_ENABLE BIT(12) +# define DSI0_PHYC_HS_CLK_CONTINUOUS BIT(10) +# define DSI0_PHYC_CLANE_ULPS BIT(9) +# define DSI_PHYC_DLANE2_ULPS BIT(9) +# define DSI0_PHYC_CLANE_ENABLE BIT(8) +# define DSI_PHYC_DLANE2_ENABLE BIT(8) +# define DSI_PHYC_DLANE1_ULPS BIT(5) +# define DSI_PHYC_DLANE1_ENABLE BIT(4) +# define DSI_PHYC_DLANE0_FORCE_STOP BIT(2) +# define DSI_PHYC_DLANE0_ULPS BIT(1) +# define DSI_PHYC_DLANE0_ENABLE BIT(0) + +#define DSI0_HS_CLT0 0x44 +#define DSI0_HS_CLT1 0x48 +#define DSI0_HS_CLT2 0x4c +#define DSI0_HS_DLT3 0x50 +#define DSI0_HS_DLT4 0x54 +#define DSI0_HS_DLT5 0x58 +#define DSI0_HS_DLT6 0x5c +#define DSI0_HS_DLT7 0x60 + +#define DSI0_PHY_AFEC0 0x64 +# define DSI0_PHY_AFEC0_DDR2CLK_EN BIT(26) +# define DSI0_PHY_AFEC0_DDRCLK_EN BIT(25) +# define DSI0_PHY_AFEC0_LATCH_ULPS BIT(24) +# define DSI1_PHY_AFEC0_IDR_DLANE3_MASK VC4_MASK(31, 29) +# define DSI1_PHY_AFEC0_IDR_DLANE3_SHIFT 29 +# define DSI1_PHY_AFEC0_IDR_DLANE2_MASK VC4_MASK(28, 26) +# define DSI1_PHY_AFEC0_IDR_DLANE2_SHIFT 26 +# define DSI1_PHY_AFEC0_IDR_DLANE1_MASK VC4_MASK(27, 23) +# define DSI1_PHY_AFEC0_IDR_DLANE1_SHIFT 23 +# define DSI1_PHY_AFEC0_IDR_DLANE0_MASK VC4_MASK(22, 20) +# define DSI1_PHY_AFEC0_IDR_DLANE0_SHIFT 20 +# define DSI1_PHY_AFEC0_IDR_CLANE_MASK VC4_MASK(19, 17) +# define DSI1_PHY_AFEC0_IDR_CLANE_SHIFT 17 +# define DSI0_PHY_AFEC0_ACTRL_DLANE1_MASK VC4_MASK(23, 20) +# define DSI0_PHY_AFEC0_ACTRL_DLANE1_SHIFT 20 +# define DSI0_PHY_AFEC0_ACTRL_DLANE0_MASK VC4_MASK(19, 16) +# define DSI0_PHY_AFEC0_ACTRL_DLANE0_SHIFT 16 +# define DSI0_PHY_AFEC0_ACTRL_CLANE_MASK VC4_MASK(15, 12) +# define DSI0_PHY_AFEC0_ACTRL_CLANE_SHIFT 12 +# define DSI1_PHY_AFEC0_DDR2CLK_EN BIT(16) +# define DSI1_PHY_AFEC0_DDRCLK_EN BIT(15) +# define DSI1_PHY_AFEC0_LATCH_ULPS BIT(14) +# define DSI1_PHY_AFEC0_RESET BIT(13) +# define DSI1_PHY_AFEC0_PD BIT(12) +# define DSI0_PHY_AFEC0_RESET BIT(11) +# define DSI1_PHY_AFEC0_PD_BG BIT(11) +# define DSI0_PHY_AFEC0_PD BIT(10) +# define DSI1_PHY_AFEC0_PD_DLANE3 BIT(10) +# define DSI0_PHY_AFEC0_PD_BG BIT(9) +# define DSI1_PHY_AFEC0_PD_DLANE2 BIT(9) +# define DSI0_PHY_AFEC0_PD_DLANE1 BIT(8) +# define DSI1_PHY_AFEC0_PD_DLANE1 BIT(8) +# define DSI_PHY_AFEC0_PTATADJ_MASK VC4_MASK(7, 4) +# define DSI_PHY_AFEC0_PTATADJ_SHIFT 4 +# define DSI_PHY_AFEC0_CTATADJ_MASK VC4_MASK(3, 0) +# define DSI_PHY_AFEC0_CTATADJ_SHIFT 0 + +#define DSI0_PHY_AFEC1 0x68 +# define DSI0_PHY_AFEC1_IDR_DLANE1_MASK VC4_MASK(10, 8) +# define DSI0_PHY_AFEC1_IDR_DLANE1_SHIFT 8 +# define DSI0_PHY_AFEC1_IDR_DLANE0_MASK VC4_MASK(6, 4) +# define DSI0_PHY_AFEC1_IDR_DLANE0_SHIFT 4 +# define DSI0_PHY_AFEC1_IDR_CLANE_MASK VC4_MASK(2, 0) +# define DSI0_PHY_AFEC1_IDR_CLANE_SHIFT 0 + +#define DSI0_TST_SEL 0x6c +#define DSI0_TST_MON 0x70 +#define DSI0_ID 0x74 +# define DSI_ID_VALUE 0x00647369 + +#define DSI1_CTRL 0x00 +# define DSI_CTRL_HS_CLKC_MASK VC4_MASK(15, 14) +# define DSI_CTRL_HS_CLKC_SHIFT 14 +# define DSI_CTRL_HS_CLKC_BYTE 0 +# define DSI_CTRL_HS_CLKC_DDR2 1 +# define DSI_CTRL_HS_CLKC_DDR 2 + +# define DSI_CTRL_RX_LPDT_EOT_DISABLE BIT(13) +# define DSI_CTRL_LPDT_EOT_DISABLE BIT(12) +# define DSI_CTRL_HSDT_EOT_DISABLE BIT(11) +# define DSI_CTRL_SOFT_RESET_CFG BIT(10) +# define DSI_CTRL_CAL_BYTE BIT(9) +# define DSI_CTRL_INV_BYTE BIT(8) +# define DSI_CTRL_CLR_LDF BIT(7) +# define DSI0_CTRL_CLR_PBCF BIT(6) +# define DSI1_CTRL_CLR_RXF BIT(6) +# define DSI0_CTRL_CLR_CPBCF BIT(5) +# define DSI1_CTRL_CLR_PDF BIT(5) +# define DSI0_CTRL_CLR_PDF BIT(4) +# define DSI1_CTRL_CLR_CDF BIT(4) +# define DSI0_CTRL_CLR_CDF BIT(3) +# define DSI0_CTRL_CTRL2 BIT(2) +# define DSI1_CTRL_DISABLE_DISP_CRCC BIT(2) +# define DSI0_CTRL_CTRL1 BIT(1) +# define DSI1_CTRL_DISABLE_DISP_ECCC BIT(1) +# define DSI0_CTRL_CTRL0 BIT(0) +# define DSI1_CTRL_EN BIT(0) +# define DSI0_CTRL_RESET_FIFOS (DSI_CTRL_CLR_LDF | \ + DSI0_CTRL_CLR_PBCF | \ + DSI0_CTRL_CLR_CPBCF | \ + DSI0_CTRL_CLR_PDF | \ + DSI0_CTRL_CLR_CDF) +# define DSI1_CTRL_RESET_FIFOS (DSI_CTRL_CLR_LDF | \ + DSI1_CTRL_CLR_RXF | \ + DSI1_CTRL_CLR_PDF | \ + DSI1_CTRL_CLR_CDF) + +#define DSI1_TXPKT2C 0x0c +#define DSI1_TXPKT2H 0x10 +#define DSI1_TXPKT_PIX_FIFO 0x20 +#define DSI1_RXPKT_FIFO 0x24 +#define DSI1_DISP0_CTRL 0x28 +#define DSI1_INT_STAT 0x30 +#define DSI1_INT_EN 0x34 +/* State reporting bits. These mostly behave like INT_STAT, where + * writing a 1 clears the bit. + */ +#define DSI1_STAT 0x38 +# define DSI1_STAT_PHY_D3_ULPS BIT(31) +# define DSI1_STAT_PHY_D3_STOP BIT(30) +# define DSI1_STAT_PHY_D2_ULPS BIT(29) +# define DSI1_STAT_PHY_D2_STOP BIT(28) +# define DSI1_STAT_PHY_D1_ULPS BIT(27) +# define DSI1_STAT_PHY_D1_STOP BIT(26) +# define DSI1_STAT_PHY_D0_ULPS BIT(25) +# define DSI1_STAT_PHY_D0_STOP BIT(24) +# define DSI1_STAT_FIFO_ERR BIT(23) +# define DSI1_STAT_PHY_RXLPDT BIT(22) +# define DSI1_STAT_PHY_RXTRIG BIT(21) +# define DSI1_STAT_PHY_D0_LPDT BIT(20) +/* Set when in forward direction */ +# define DSI1_STAT_PHY_DIR BIT(19) +# define DSI1_STAT_PHY_CLOCK_ULPS BIT(18) +# define DSI1_STAT_PHY_CLOCK_HS BIT(17) +# define DSI1_STAT_PHY_CLOCK_STOP BIT(16) +# define DSI1_STAT_PR_TO BIT(15) +# define DSI1_STAT_TA_TO BIT(14) +# define DSI1_STAT_LPRX_TO BIT(13) +# define DSI1_STAT_HSTX_TO BIT(12) +# define DSI1_STAT_ERR_CONT_LP1 BIT(11) +# define DSI1_STAT_ERR_CONT_LP0 BIT(10) +# define DSI1_STAT_ERR_CONTROL BIT(9) +# define DSI1_STAT_ERR_SYNC_ESC BIT(8) +# define DSI1_STAT_RXPKT2 BIT(7) +# define DSI1_STAT_RXPKT1 BIT(6) +# define DSI1_STAT_TXPKT2_BUSY BIT(5) +# define DSI1_STAT_TXPKT2_DONE BIT(4) +# define DSI1_STAT_TXPKT2_END BIT(3) +# define DSI1_STAT_TXPKT1_BUSY BIT(2) +# define DSI1_STAT_TXPKT1_DONE BIT(1) +# define DSI1_STAT_TXPKT1_END BIT(0) + +#define DSI1_HSTX_TO_CNT 0x3c +#define DSI1_LPRX_TO_CNT 0x40 +#define DSI1_TA_TO_CNT 0x44 +#define DSI1_PR_TO_CNT 0x48 +#define DSI1_PHYC 0x4c + +#define DSI1_HS_CLT0 0x50 +# define DSI_HS_CLT0_CZERO_MASK VC4_MASK(26, 18) +# define DSI_HS_CLT0_CZERO_SHIFT 18 +# define DSI_HS_CLT0_CPRE_MASK VC4_MASK(17, 9) +# define DSI_HS_CLT0_CPRE_SHIFT 9 +# define DSI_HS_CLT0_CPREP_MASK VC4_MASK(8, 0) +# define DSI_HS_CLT0_CPREP_SHIFT 0 + +#define DSI1_HS_CLT1 0x54 +# define DSI_HS_CLT1_CTRAIL_MASK VC4_MASK(17, 9) +# define DSI_HS_CLT1_CTRAIL_SHIFT 9 +# define DSI_HS_CLT1_CPOST_MASK VC4_MASK(8, 0) +# define DSI_HS_CLT1_CPOST_SHIFT 0 + +#define DSI1_HS_CLT2 0x58 +# define DSI_HS_CLT2_WUP_MASK VC4_MASK(23, 0) +# define DSI_HS_CLT2_WUP_SHIFT 0 + +#define DSI1_HS_DLT3 0x5c +# define DSI_HS_DLT3_EXIT_MASK VC4_MASK(26, 18) +# define DSI_HS_DLT3_EXIT_SHIFT 18 +# define DSI_HS_DLT3_ZERO_MASK VC4_MASK(17, 9) +# define DSI_HS_DLT3_ZERO_SHIFT 9 +# define DSI_HS_DLT3_PRE_MASK VC4_MASK(8, 0) +# define DSI_HS_DLT3_PRE_SHIFT 0 + +#define DSI1_HS_DLT4 0x60 +# define DSI_HS_DLT4_ANLAT_MASK VC4_MASK(22, 18) +# define DSI_HS_DLT4_ANLAT_SHIFT 18 +# define DSI_HS_DLT4_TRAIL_MASK VC4_MASK(17, 9) +# define DSI_HS_DLT4_TRAIL_SHIFT 9 +# define DSI_HS_DLT4_LPX_MASK VC4_MASK(8, 0) +# define DSI_HS_DLT4_LPX_SHIFT 0 + +#define DSI1_HS_DLT5 0x64 +# define DSI_HS_DLT5_INIT_MASK VC4_MASK(23, 0) +# define DSI_HS_DLT5_INIT_SHIFT 0 + +#define DSI1_HS_DLT6 0x68 +# define DSI_HS_DLT6_TA_GET_MASK VC4_MASK(31, 24) +# define DSI_HS_DLT6_TA_GET_SHIFT 24 +# define DSI_HS_DLT6_TA_SURE_MASK VC4_MASK(23, 16) +# define DSI_HS_DLT6_TA_SURE_SHIFT 16 +# define DSI_HS_DLT6_TA_GO_MASK VC4_MASK(15, 8) +# define DSI_HS_DLT6_TA_GO_SHIFT 8 +# define DSI_HS_DLT6_LP_LPX_MASK VC4_MASK(7, 0) +# define DSI_HS_DLT6_LP_LPX_SHIFT 0 + +#define DSI1_HS_DLT7 0x6c +# define DSI_HS_DLT7_LP_WUP_MASK VC4_MASK(23, 0) +# define DSI_HS_DLT7_LP_WUP_SHIFT 0 + +#define DSI1_PHY_AFEC0 0x70 + +#define DSI1_PHY_AFEC1 0x74 +# define DSI1_PHY_AFEC1_ACTRL_DLANE3_MASK VC4_MASK(19, 16) +# define DSI1_PHY_AFEC1_ACTRL_DLANE3_SHIFT 16 +# define DSI1_PHY_AFEC1_ACTRL_DLANE2_MASK VC4_MASK(15, 12) +# define DSI1_PHY_AFEC1_ACTRL_DLANE2_SHIFT 12 +# define DSI1_PHY_AFEC1_ACTRL_DLANE1_MASK VC4_MASK(11, 8) +# define DSI1_PHY_AFEC1_ACTRL_DLANE1_SHIFT 8 +# define DSI1_PHY_AFEC1_ACTRL_DLANE0_MASK VC4_MASK(7, 4) +# define DSI1_PHY_AFEC1_ACTRL_DLANE0_SHIFT 4 +# define DSI1_PHY_AFEC1_ACTRL_CLANE_MASK VC4_MASK(3, 0) +# define DSI1_PHY_AFEC1_ACTRL_CLANE_SHIFT 0 + +#define DSI1_TST_SEL 0x78 +#define DSI1_TST_MON 0x7c +#define DSI1_PHY_TST1 0x80 +#define DSI1_PHY_TST2 0x84 +#define DSI1_PHY_FIFO_STAT 0x88 +/* Actually, all registers in the range that aren't otherwise claimed + * will return the ID. + */ +#define DSI1_ID 0x8c + +/* General DSI hardware state. */ +struct vc4_dsi { + struct platform_device *pdev; + + struct mipi_dsi_host dsi_host; + struct drm_encoder *encoder; + struct drm_connector *connector; + struct drm_panel *panel; + + void __iomem *regs; + + struct dma_chan *reg_dma_chan; + dma_addr_t reg_dma_paddr; + u32 *reg_dma_mem; + dma_addr_t reg_paddr; + + /* Whether we're on bcm2835's DSI0 or DSI1. */ + int port; + + /* DSI channel for the panel we're connected to. */ + u32 channel; + u32 lanes; + enum mipi_dsi_pixel_format format; + u32 mode_flags; + + /* Input clock from CPRMAN to the digital PHY, for the DSI + * escape clock. + */ + struct clk *escape_clock; + + /* Input clock to the analog PHY, used to generate the DSI bit + * clock. + */ + struct clk *pll_phy_clock; + + /* HS Clocks generated within the DSI analog PHY. */ + struct clk_fixed_factor phy_clocks[3]; + + struct clk_onecell_data clk_onecell; + + /* Pixel clock output to the pixelvalve, generated from the HS + * clock. + */ + struct clk *pixel_clock; + + struct completion xfer_completion; + int xfer_result; +}; + +#define host_to_dsi(host) container_of(host, struct vc4_dsi, dsi_host) + +static inline void +dsi_dma_workaround_write(struct vc4_dsi *dsi, u32 offset, u32 val) +{ + struct dma_chan *chan = dsi->reg_dma_chan; + struct dma_async_tx_descriptor *tx; + dma_cookie_t cookie; + int ret; + + /* DSI0 should be able to write normally. */ + if (!chan) { + writel(val, dsi->regs + offset); + return; + } + + *dsi->reg_dma_mem = val; + + tx = chan->device->device_prep_dma_memcpy(chan, + dsi->reg_paddr + offset, + dsi->reg_dma_paddr, + 4, 0); + if (!tx) { + DRM_ERROR("Failed to set up DMA register write\n"); + return; + } + + cookie = tx->tx_submit(tx); + ret = dma_submit_error(cookie); + if (ret) { + DRM_ERROR("Failed to submit DMA: %d\n", ret); + return; + } + ret = dma_sync_wait(chan, cookie); + if (ret) + DRM_ERROR("Failed to wait for DMA: %d\n", ret); +} + +#define DSI_READ(offset) readl(dsi->regs + (offset)) +#define DSI_WRITE(offset, val) dsi_dma_workaround_write(dsi, offset, val) +#define DSI_PORT_READ(offset) \ + DSI_READ(dsi->port ? DSI1_##offset : DSI0_##offset) +#define DSI_PORT_WRITE(offset, val) \ + DSI_WRITE(dsi->port ? DSI1_##offset : DSI0_##offset, val) +#define DSI_PORT_BIT(bit) (dsi->port ? DSI1_##bit : DSI0_##bit) + +/* VC4 DSI encoder KMS struct */ +struct vc4_dsi_encoder { + struct vc4_encoder base; + struct vc4_dsi *dsi; +}; + +static inline struct vc4_dsi_encoder * +to_vc4_dsi_encoder(struct drm_encoder *encoder) +{ + return container_of(encoder, struct vc4_dsi_encoder, base.base); +} + +/* VC4 DSI connector KMS struct */ +struct vc4_dsi_connector { + struct drm_connector base; + struct vc4_dsi *dsi; +}; + +static inline struct vc4_dsi_connector * +to_vc4_dsi_connector(struct drm_connector *connector) +{ + return container_of(connector, struct vc4_dsi_connector, base); +} + +#define DSI_REG(reg) { reg, #reg } +static const struct { + u32 reg; + const char *name; +} dsi0_regs[] = { + DSI_REG(DSI0_CTRL), + DSI_REG(DSI0_STAT), + DSI_REG(DSI0_HSTX_TO_CNT), + DSI_REG(DSI0_LPRX_TO_CNT), + DSI_REG(DSI0_TA_TO_CNT), + DSI_REG(DSI0_PR_TO_CNT), + DSI_REG(DSI0_DISP0_CTRL), + DSI_REG(DSI0_DISP1_CTRL), + DSI_REG(DSI0_INT_STAT), + DSI_REG(DSI0_INT_EN), + DSI_REG(DSI0_PHYC), + DSI_REG(DSI0_HS_CLT0), + DSI_REG(DSI0_HS_CLT1), + DSI_REG(DSI0_HS_CLT2), + DSI_REG(DSI0_HS_DLT3), + DSI_REG(DSI0_HS_DLT4), + DSI_REG(DSI0_HS_DLT5), + DSI_REG(DSI0_HS_DLT6), + DSI_REG(DSI0_HS_DLT7), + DSI_REG(DSI0_PHY_AFEC0), + DSI_REG(DSI0_PHY_AFEC1), + DSI_REG(DSI0_ID), +}; + +static const struct { + u32 reg; + const char *name; +} dsi1_regs[] = { + DSI_REG(DSI1_CTRL), + DSI_REG(DSI1_STAT), + DSI_REG(DSI1_HSTX_TO_CNT), + DSI_REG(DSI1_LPRX_TO_CNT), + DSI_REG(DSI1_TA_TO_CNT), + DSI_REG(DSI1_PR_TO_CNT), + DSI_REG(DSI1_DISP0_CTRL), + DSI_REG(DSI1_DISP1_CTRL), + DSI_REG(DSI1_INT_STAT), + DSI_REG(DSI1_INT_EN), + DSI_REG(DSI1_PHYC), + DSI_REG(DSI1_HS_CLT0), + DSI_REG(DSI1_HS_CLT1), + DSI_REG(DSI1_HS_CLT2), + DSI_REG(DSI1_HS_DLT3), + DSI_REG(DSI1_HS_DLT4), + DSI_REG(DSI1_HS_DLT5), + DSI_REG(DSI1_HS_DLT6), + DSI_REG(DSI1_HS_DLT7), + DSI_REG(DSI1_PHY_AFEC0), + DSI_REG(DSI1_PHY_AFEC1), + DSI_REG(DSI1_ID), +}; + +static void vc4_dsi_dump_regs(struct vc4_dsi *dsi) +{ + int i; + + if (dsi->port == 0) { + for (i = 0; i < ARRAY_SIZE(dsi0_regs); i++) { + DRM_INFO("0x%04x (%s): 0x%08x\n", + dsi0_regs[i].reg, dsi0_regs[i].name, + DSI_READ(dsi0_regs[i].reg)); + } + } else { + for (i = 0; i < ARRAY_SIZE(dsi1_regs); i++) { + DRM_INFO("0x%04x (%s): 0x%08x\n", + dsi1_regs[i].reg, dsi1_regs[i].name, + DSI_READ(dsi1_regs[i].reg)); + } + } +} + +#ifdef CONFIG_DEBUG_FS +int vc4_dsi_debugfs_regs(struct seq_file *m, void *unused) +{ + struct drm_info_node *node = (struct drm_info_node *)m->private; + struct drm_device *drm = node->minor->dev; + struct vc4_dev *vc4 = to_vc4_dev(drm); + int dsi_index = (uintptr_t)node->info_ent->data; + struct vc4_dsi *dsi = (dsi_index == 1 ? vc4->dsi1 : NULL); + int i; + + if (!dsi) + return 0; + + if (dsi->port == 0) { + for (i = 0; i < ARRAY_SIZE(dsi0_regs); i++) { + seq_printf(m, "0x%04x (%s): 0x%08x\n", + dsi0_regs[i].reg, dsi0_regs[i].name, + DSI_READ(dsi0_regs[i].reg)); + } + } else { + for (i = 0; i < ARRAY_SIZE(dsi1_regs); i++) { + seq_printf(m, "0x%04x (%s): 0x%08x\n", + dsi1_regs[i].reg, dsi1_regs[i].name, + DSI_READ(dsi1_regs[i].reg)); + } + } + + return 0; +} +#endif + +static enum drm_connector_status +vc4_dsi_connector_detect(struct drm_connector *connector, bool force) +{ + struct vc4_dsi_connector *vc4_connector = + to_vc4_dsi_connector(connector); + struct vc4_dsi *dsi = vc4_connector->dsi; + + if (dsi->panel) + return connector_status_connected; + else + return connector_status_disconnected; +} + +static void vc4_dsi_connector_destroy(struct drm_connector *connector) +{ + drm_connector_unregister(connector); + drm_connector_cleanup(connector); +} + +static int vc4_dsi_connector_get_modes(struct drm_connector *connector) +{ + struct vc4_dsi_connector *vc4_connector = + to_vc4_dsi_connector(connector); + struct vc4_dsi *dsi = vc4_connector->dsi; + + if (dsi->panel) + return drm_panel_get_modes(dsi->panel); + + return 0; +} + +static const struct drm_connector_funcs vc4_dsi_connector_funcs = { + .dpms = drm_atomic_helper_connector_dpms, + .detect = vc4_dsi_connector_detect, + .fill_modes = drm_helper_probe_single_connector_modes, + .destroy = vc4_dsi_connector_destroy, + .reset = drm_atomic_helper_connector_reset, + .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, + .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, +}; + +static const struct drm_connector_helper_funcs vc4_dsi_connector_helper_funcs = { + .get_modes = vc4_dsi_connector_get_modes, +}; + +static struct drm_connector *vc4_dsi_connector_init(struct drm_device *dev, + struct vc4_dsi *dsi) +{ + struct drm_connector *connector = NULL; + struct vc4_dsi_connector *dsi_connector; + int ret = 0; + + dsi_connector = devm_kzalloc(dev->dev, sizeof(*dsi_connector), + GFP_KERNEL); + if (!dsi_connector) { + ret = -ENOMEM; + goto fail; + } + connector = &dsi_connector->base; + + dsi_connector->dsi = dsi; + + drm_connector_init(dev, connector, &vc4_dsi_connector_funcs, + DRM_MODE_CONNECTOR_DSI); + drm_connector_helper_add(connector, &vc4_dsi_connector_helper_funcs); + + connector->polled = 0; + connector->interlace_allowed = 0; + connector->doublescan_allowed = 0; + + drm_mode_connector_attach_encoder(connector, dsi->encoder); + + return connector; + +fail: + if (connector) + vc4_dsi_connector_destroy(connector); + + return ERR_PTR(ret); +} + +static void vc4_dsi_encoder_destroy(struct drm_encoder *encoder) +{ + drm_encoder_cleanup(encoder); +} + +static const struct drm_encoder_funcs vc4_dsi_encoder_funcs = { + .destroy = vc4_dsi_encoder_destroy, +}; + +static void vc4_dsi_latch_ulps(struct vc4_dsi *dsi, bool latch) +{ + u32 afec0 = DSI_PORT_READ(PHY_AFEC0); + + if (latch) + afec0 |= DSI_PORT_BIT(PHY_AFEC0_LATCH_ULPS); + else + afec0 &= ~DSI_PORT_BIT(PHY_AFEC0_LATCH_ULPS); + + DSI_PORT_WRITE(PHY_AFEC0, afec0); +} + +/* Enters or exits Ultra Low Power State. */ +static void vc4_dsi_ulps(struct vc4_dsi *dsi, bool ulps) +{ + bool continuous = dsi->mode_flags & MIPI_DSI_CLOCK_NON_CONTINUOUS; + u32 phyc_ulps = ((continuous ? DSI_PORT_BIT(PHYC_CLANE_ULPS) : 0) | + DSI_PHYC_DLANE0_ULPS | + (dsi->lanes > 1 ? DSI_PHYC_DLANE1_ULPS : 0) | + (dsi->lanes > 2 ? DSI_PHYC_DLANE2_ULPS : 0) | + (dsi->lanes > 3 ? DSI_PHYC_DLANE3_ULPS : 0)); + u32 stat_ulps = ((continuous ? DSI1_STAT_PHY_CLOCK_ULPS : 0) | + DSI1_STAT_PHY_D0_ULPS | + (dsi->lanes > 1 ? DSI1_STAT_PHY_D1_ULPS : 0) | + (dsi->lanes > 2 ? DSI1_STAT_PHY_D2_ULPS : 0) | + (dsi->lanes > 3 ? DSI1_STAT_PHY_D3_ULPS : 0)); + u32 stat_stop = ((continuous ? DSI1_STAT_PHY_CLOCK_STOP : 0) | + DSI1_STAT_PHY_D0_STOP | + (dsi->lanes > 1 ? DSI1_STAT_PHY_D1_STOP : 0) | + (dsi->lanes > 2 ? DSI1_STAT_PHY_D2_STOP : 0) | + (dsi->lanes > 3 ? DSI1_STAT_PHY_D3_STOP : 0)); + int ret; + + DSI_PORT_WRITE(STAT, stat_ulps); + DSI_PORT_WRITE(PHYC, DSI_PORT_READ(PHYC) | phyc_ulps); + ret = wait_for((DSI_PORT_READ(STAT) & stat_ulps) == stat_ulps, 200); + if (ret) { + dev_warn(&dsi->pdev->dev, + "Timeout waiting for DSI ULPS entry: STAT 0x%08x", + DSI_PORT_READ(STAT)); + DSI_PORT_WRITE(PHYC, DSI_PORT_READ(PHYC) & ~phyc_ulps); + vc4_dsi_latch_ulps(dsi, false); + return; + } + + /* The DSI module can't be disabled while the module is + * generating ULPS state. So, to be able to disable the + * module, we have the AFE latch the ULPS state and continue + * on to having the module enter STOP. + */ + vc4_dsi_latch_ulps(dsi, ulps); + + DSI_PORT_WRITE(STAT, stat_stop); + DSI_PORT_WRITE(PHYC, DSI_PORT_READ(PHYC) & ~phyc_ulps); + ret = wait_for((DSI_PORT_READ(STAT) & stat_stop) == stat_stop, 200); + if (ret) { + dev_warn(&dsi->pdev->dev, + "Timeout waiting for DSI STOP entry: STAT 0x%08x", + DSI_PORT_READ(STAT)); + DSI_PORT_WRITE(PHYC, DSI_PORT_READ(PHYC) & ~phyc_ulps); + return; + } +} + +static u32 +dsi_hs_timing(u32 ui_ns, u32 ns, u32 ui) +{ + /* The HS timings have to be rounded up to a multiple of 8 + * because we're using the byte clock. + */ + return roundup(ui + DIV_ROUND_UP(ns, ui_ns), 8); +} + +/* ESC always runs at 100Mhz. */ +#define ESC_TIME_NS 10 + +static u32 +dsi_esc_timing(u32 ns) +{ + return DIV_ROUND_UP(ns, ESC_TIME_NS); +} + +static void vc4_dsi_encoder_disable(struct drm_encoder *encoder) +{ + struct vc4_dsi_encoder *vc4_encoder = to_vc4_dsi_encoder(encoder); + struct vc4_dsi *dsi = vc4_encoder->dsi; + struct device *dev = &dsi->pdev->dev; + + drm_panel_disable(dsi->panel); + + vc4_dsi_ulps(dsi, true); + + drm_panel_unprepare(dsi->panel); + + clk_disable_unprepare(dsi->pll_phy_clock); + clk_disable_unprepare(dsi->escape_clock); + clk_disable_unprepare(dsi->pixel_clock); + + pm_runtime_put(dev); +} + +static void vc4_dsi_encoder_enable(struct drm_encoder *encoder) +{ + struct drm_display_mode *mode = &encoder->crtc->mode; + struct vc4_dsi_encoder *vc4_encoder = to_vc4_dsi_encoder(encoder); + struct vc4_dsi *dsi = vc4_encoder->dsi; + struct device *dev = &dsi->pdev->dev; + u32 format = 0, divider = 0; + bool debug_dump_regs = false; + unsigned long hs_clock; + u32 ui_ns; + /* Minimum LP state duration in escape clock cycles. */ + u32 lpx = dsi_esc_timing(60); + unsigned long pixel_clock_hz = mode->clock * 1000; + unsigned long dsip_clock; + unsigned long phy_clock; + int ret; + + ret = pm_runtime_get_sync(dev); + if (ret) { + DRM_ERROR("Failed to runtime PM enable on DSI%d\n", dsi->port); + return; + } + + ret = drm_panel_prepare(dsi->panel); + if (ret) { + DRM_ERROR("Panel failed to prepare\n"); + return; + } + + if (debug_dump_regs) { + DRM_INFO("DSI regs before:\n"); + vc4_dsi_dump_regs(dsi); + } + + switch (dsi->format) { + case MIPI_DSI_FMT_RGB888: + format = DSI_PFORMAT_RGB888; + divider = 24 / dsi->lanes; + break; + case MIPI_DSI_FMT_RGB666: + format = DSI_PFORMAT_RGB666; + divider = 24 / dsi->lanes; + break; + case MIPI_DSI_FMT_RGB666_PACKED: + format = DSI_PFORMAT_RGB666_PACKED; + divider = 18 / dsi->lanes; + break; + case MIPI_DSI_FMT_RGB565: + format = DSI_PFORMAT_RGB565; + divider = 16 / dsi->lanes; + break; + } + + phy_clock = pixel_clock_hz * divider; + ret = clk_set_rate(dsi->pll_phy_clock, phy_clock); + if (ret) { + dev_err(&dsi->pdev->dev, + "Failed to set phy clock to %ld: %d\n", phy_clock, ret); + } + + /* Reset the DSI and all its fifos. */ + DSI_PORT_WRITE(CTRL, + DSI_CTRL_SOFT_RESET_CFG | + DSI_PORT_BIT(CTRL_RESET_FIFOS)); + + DSI_PORT_WRITE(CTRL, + DSI_CTRL_HSDT_EOT_DISABLE | + DSI_CTRL_RX_LPDT_EOT_DISABLE); + + /* Clear all stat bits so we see what has happened during enable. */ + DSI_PORT_WRITE(STAT, DSI_PORT_READ(STAT)); + + /* Set AFE CTR00/CTR1 to release powerdown of analog. */ + if (dsi->port == 0) { + u32 afec0 = (VC4_SET_FIELD(7, DSI_PHY_AFEC0_PTATADJ) | + VC4_SET_FIELD(7, DSI_PHY_AFEC0_CTATADJ)); + + if (dsi->lanes < 2) + afec0 |= DSI0_PHY_AFEC0_PD_DLANE1; + + if (!(dsi->mode_flags & MIPI_DSI_MODE_VIDEO)) + afec0 |= DSI0_PHY_AFEC0_RESET; + + DSI_PORT_WRITE(PHY_AFEC0, afec0); + + DSI_PORT_WRITE(PHY_AFEC1, + VC4_SET_FIELD(6, DSI0_PHY_AFEC1_IDR_DLANE1) | + VC4_SET_FIELD(6, DSI0_PHY_AFEC1_IDR_DLANE0) | + VC4_SET_FIELD(6, DSI0_PHY_AFEC1_IDR_CLANE)); + } else { + u32 afec0 = (VC4_SET_FIELD(7, DSI_PHY_AFEC0_PTATADJ) | + VC4_SET_FIELD(7, DSI_PHY_AFEC0_CTATADJ) | + VC4_SET_FIELD(6, DSI1_PHY_AFEC0_IDR_CLANE) | + VC4_SET_FIELD(6, DSI1_PHY_AFEC0_IDR_DLANE0) | + VC4_SET_FIELD(6, DSI1_PHY_AFEC0_IDR_DLANE1) | + VC4_SET_FIELD(6, DSI1_PHY_AFEC0_IDR_DLANE2) | + VC4_SET_FIELD(6, DSI1_PHY_AFEC0_IDR_DLANE3)); + + if (dsi->lanes < 4) + afec0 |= DSI1_PHY_AFEC0_PD_DLANE3; + if (dsi->lanes < 3) + afec0 |= DSI1_PHY_AFEC0_PD_DLANE2; + if (dsi->lanes < 2) + afec0 |= DSI1_PHY_AFEC0_PD_DLANE1; + + afec0 |= DSI1_PHY_AFEC0_RESET; + + DSI_PORT_WRITE(PHY_AFEC0, afec0); + + DSI_PORT_WRITE(PHY_AFEC1, 0); + + /* AFEC reset hold time */ + mdelay(1); + } + + ret = clk_prepare_enable(dsi->escape_clock); + if (ret) { + DRM_ERROR("Failed to turn on DSI escape clock: %d\n", ret); + return; + } + + ret = clk_prepare_enable(dsi->pll_phy_clock); + if (ret) { + DRM_ERROR("Failed to turn on DSI PLL: %d\n", ret); + return; + } + + hs_clock = clk_get_rate(dsi->pll_phy_clock); + + /* Yes, we set the DSI0P/DSI1P pixel clock to the byte rate, + * not the pixel clock rate. DSIxP take from the APHY's byte, + * DDR2, or DDR4 clock (we use byte) and feed into the PV at + * that rate. Separately, a value derived from PIX_CLK_DIV + * and HS_CLKC is fed into the PV to divide down to the actual + * pixel clock for pushing pixels into DSI. + */ + dsip_clock = phy_clock / 8; + ret = clk_set_rate(dsi->pixel_clock, dsip_clock); + if (ret) { + dev_err(dev, "Failed to set pixel clock to %ldHz: %d\n", + dsip_clock, ret); + } + + ret = clk_prepare_enable(dsi->pixel_clock); + if (ret) { + DRM_ERROR("Failed to turn on DSI pixel clock: %d\n", ret); + return; + } + + /* How many ns one DSI unit interval is. Note that the clock + * is DDR, so there's an extra divide by 2. + */ + ui_ns = DIV_ROUND_UP(500000000, hs_clock); + + DSI_PORT_WRITE(HS_CLT0, + VC4_SET_FIELD(dsi_hs_timing(ui_ns, 262, 0), + DSI_HS_CLT0_CZERO) | + VC4_SET_FIELD(dsi_hs_timing(ui_ns, 0, 8), + DSI_HS_CLT0_CPRE) | + VC4_SET_FIELD(dsi_hs_timing(ui_ns, 38, 0), + DSI_HS_CLT0_CPREP)); + + DSI_PORT_WRITE(HS_CLT1, + VC4_SET_FIELD(dsi_hs_timing(ui_ns, 60, 0), + DSI_HS_CLT1_CTRAIL) | + VC4_SET_FIELD(dsi_hs_timing(ui_ns, 60, 52), + DSI_HS_CLT1_CPOST)); + + DSI_PORT_WRITE(HS_CLT2, + VC4_SET_FIELD(dsi_hs_timing(ui_ns, 1000000, 0), + DSI_HS_CLT2_WUP)); + + DSI_PORT_WRITE(HS_DLT3, + VC4_SET_FIELD(dsi_hs_timing(ui_ns, 100, 0), + DSI_HS_DLT3_EXIT) | + VC4_SET_FIELD(dsi_hs_timing(ui_ns, 105, 6), + DSI_HS_DLT3_ZERO) | + VC4_SET_FIELD(dsi_hs_timing(ui_ns, 40, 4), + DSI_HS_DLT3_PRE)); + + DSI_PORT_WRITE(HS_DLT4, + VC4_SET_FIELD(dsi_hs_timing(ui_ns, lpx * ESC_TIME_NS, 0), + DSI_HS_DLT4_LPX) | + VC4_SET_FIELD(max(dsi_hs_timing(ui_ns, 0, 8), + dsi_hs_timing(ui_ns, 60, 4)), + DSI_HS_DLT4_TRAIL) | + VC4_SET_FIELD(0, DSI_HS_DLT4_ANLAT)); + + DSI_PORT_WRITE(HS_DLT5, VC4_SET_FIELD(dsi_hs_timing(ui_ns, 1000, 5000), + DSI_HS_DLT5_INIT)); + + DSI_PORT_WRITE(HS_DLT6, + VC4_SET_FIELD(lpx * 5, DSI_HS_DLT6_TA_GET) | + VC4_SET_FIELD(lpx, DSI_HS_DLT6_TA_SURE) | + VC4_SET_FIELD(lpx * 4, DSI_HS_DLT6_TA_GO) | + VC4_SET_FIELD(lpx, DSI_HS_DLT6_LP_LPX)); + + DSI_PORT_WRITE(HS_DLT7, + VC4_SET_FIELD(dsi_esc_timing(1000000), + DSI_HS_DLT7_LP_WUP)); + + DSI_PORT_WRITE(PHYC, + DSI_PHYC_DLANE0_ENABLE | + (dsi->lanes >= 2 ? DSI_PHYC_DLANE1_ENABLE : 0) | + (dsi->lanes >= 3 ? DSI_PHYC_DLANE2_ENABLE : 0) | + (dsi->lanes >= 4 ? DSI_PHYC_DLANE3_ENABLE : 0) | + DSI_PORT_BIT(PHYC_CLANE_ENABLE) | + ((dsi->mode_flags & MIPI_DSI_CLOCK_NON_CONTINUOUS) ? + 0 : DSI_PORT_BIT(PHYC_HS_CLK_CONTINUOUS)) | + (dsi->port == 0 ? + VC4_SET_FIELD(lpx - 1, DSI0_PHYC_ESC_CLK_LPDT) : + VC4_SET_FIELD(lpx - 1, DSI1_PHYC_ESC_CLK_LPDT))); + + DSI_PORT_WRITE(CTRL, + DSI_PORT_READ(CTRL) | + DSI_CTRL_CAL_BYTE); + + /* HS timeout in HS clock cycles: disabled. */ + DSI_PORT_WRITE(HSTX_TO_CNT, 0); + /* LP receive timeout in HS clocks. */ + DSI_PORT_WRITE(LPRX_TO_CNT, 0xffffff); + /* Bus turnaround timeout */ + DSI_PORT_WRITE(TA_TO_CNT, 100000); + /* Display reset sequence timeout */ + DSI_PORT_WRITE(PR_TO_CNT, 100000); + + if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO) { + DSI_PORT_WRITE(DISP0_CTRL, + VC4_SET_FIELD(divider, DSI_DISP0_PIX_CLK_DIV) | + VC4_SET_FIELD(format, DSI_DISP0_PFORMAT) | + VC4_SET_FIELD(DSI_DISP0_LP_STOP_PERFRAME, + DSI_DISP0_LP_STOP_CTRL) | + DSI_DISP0_ST_END | + DSI_DISP0_ENABLE); + } else { + DSI_PORT_WRITE(DISP0_CTRL, + DSI_DISP0_COMMAND_MODE | + DSI_DISP0_ENABLE); + } + + /* Set up DISP1 for transferring long command payloads through + * the pixfifo. + */ + DSI_PORT_WRITE(DISP1_CTRL, + VC4_SET_FIELD(DSI_DISP1_PFORMAT_32BIT_LE, + DSI_DISP1_PFORMAT) | + DSI_DISP1_ENABLE); + + /* Ungate the block. */ + if (dsi->port == 0) + DSI_PORT_WRITE(CTRL, DSI_PORT_READ(CTRL) | DSI0_CTRL_CTRL0); + else + DSI_PORT_WRITE(CTRL, DSI_PORT_READ(CTRL) | DSI1_CTRL_EN); + + /* Bring AFE out of reset. */ + if (dsi->port == 0) { + } else { + DSI_PORT_WRITE(PHY_AFEC0, + DSI_PORT_READ(PHY_AFEC0) & + ~DSI1_PHY_AFEC0_RESET); + } + + vc4_dsi_ulps(dsi, false); + + if (debug_dump_regs) { + DRM_INFO("DSI regs after:\n"); + vc4_dsi_dump_regs(dsi); + } + + ret = drm_panel_enable(dsi->panel); + if (ret) { + DRM_ERROR("Panel failed to enable\n"); + drm_panel_unprepare(dsi->panel); + return; + } +} + +static ssize_t vc4_dsi_host_transfer(struct mipi_dsi_host *host, + const struct mipi_dsi_msg *msg) +{ + struct vc4_dsi *dsi = host_to_dsi(host); + struct mipi_dsi_packet packet; + u32 pkth = 0, pktc = 0; + int i, ret; + bool is_long = mipi_dsi_packet_format_is_long(msg->type); + u32 cmd_fifo_len = 0, pix_fifo_len = 0; + + mipi_dsi_create_packet(&packet, msg); + + pkth |= VC4_SET_FIELD(packet.header[0], DSI_TXPKT1H_BC_DT); + pkth |= VC4_SET_FIELD(packet.header[1] | + (packet.header[2] << 8), + DSI_TXPKT1H_BC_PARAM); + if (is_long) { + /* Divide data across the various FIFOs we have available. + * The command FIFO takes byte-oriented data, but is of + * limited size. The pixel FIFO (never actually used for + * pixel data in reality) is word oriented, and substantially + * larger. So, we use the pixel FIFO for most of the data, + * sending the residual bytes in the command FIFO at the start. + * + * With this arrangement, the command FIFO will never get full. + */ + if (packet.payload_length <= 16) { + cmd_fifo_len = packet.payload_length; + pix_fifo_len = 0; + } else { + cmd_fifo_len = (packet.payload_length % + DSI_PIX_FIFO_WIDTH); + pix_fifo_len = ((packet.payload_length - cmd_fifo_len) / + DSI_PIX_FIFO_WIDTH); + } + + WARN_ON_ONCE(pix_fifo_len >= DSI_PIX_FIFO_DEPTH); + + pkth |= VC4_SET_FIELD(cmd_fifo_len, DSI_TXPKT1H_BC_CMDFIFO); + } + + if (msg->rx_len) { + pktc |= VC4_SET_FIELD(DSI_TXPKT1C_CMD_CTRL_RX, + DSI_TXPKT1C_CMD_CTRL); + } else { + pktc |= VC4_SET_FIELD(DSI_TXPKT1C_CMD_CTRL_TX, + DSI_TXPKT1C_CMD_CTRL); + } + + for (i = 0; i < cmd_fifo_len; i++) + DSI_PORT_WRITE(TXPKT_CMD_FIFO, packet.payload[i]); + for (i = 0; i < pix_fifo_len; i++) { + const u8 *pix = packet.payload + cmd_fifo_len + i * 4; + + DSI_PORT_WRITE(TXPKT_PIX_FIFO, + pix[0] | + pix[1] << 8 | + pix[2] << 16 | + pix[3] << 24); + } + + if (msg->flags & MIPI_DSI_MSG_USE_LPM) + pktc |= DSI_TXPKT1C_CMD_MODE_LP; + if (is_long) + pktc |= DSI_TXPKT1C_CMD_TYPE_LONG; + + /* Send one copy of the packet. Larger repeats are used for pixel + * data in command mode. + */ + pktc |= VC4_SET_FIELD(1, DSI_TXPKT1C_CMD_REPEAT); + + pktc |= DSI_TXPKT1C_CMD_EN; + if (pix_fifo_len) { + pktc |= VC4_SET_FIELD(DSI_TXPKT1C_DISPLAY_NO_SECONDARY, + DSI_TXPKT1C_DISPLAY_NO); + } else { + pktc |= VC4_SET_FIELD(DSI_TXPKT1C_DISPLAY_NO_SHORT, + DSI_TXPKT1C_DISPLAY_NO); + } + + /* Enable the appropriate interrupt for the transfer completion. */ + dsi->xfer_result = 0; + reinit_completion(&dsi->xfer_completion); + DSI_PORT_WRITE(INT_STAT, DSI1_INT_TXPKT1_DONE | DSI1_INT_PHY_DIR_RTF); + if (msg->rx_len) { + DSI_PORT_WRITE(INT_EN, (DSI1_INTERRUPTS_ALWAYS_ENABLED | + DSI1_INT_PHY_DIR_RTF)); + } else { + DSI_PORT_WRITE(INT_EN, (DSI1_INTERRUPTS_ALWAYS_ENABLED | + DSI1_INT_TXPKT1_DONE)); + } + + /* Send the packet. */ + DSI_PORT_WRITE(TXPKT1H, pkth); + DSI_PORT_WRITE(TXPKT1C, pktc); + + if (!wait_for_completion_timeout(&dsi->xfer_completion, + msecs_to_jiffies(1000))) { + dev_err(&dsi->pdev->dev, "transfer interrupt wait timeout"); + dev_err(&dsi->pdev->dev, "instat: 0x%08x\n", + DSI_PORT_READ(INT_STAT)); + ret = -ETIMEDOUT; + } else { + ret = dsi->xfer_result; + } + + DSI_PORT_WRITE(INT_EN, DSI1_INTERRUPTS_ALWAYS_ENABLED); + + if (ret) + goto reset_fifo_and_return; + + if (ret == 0 && msg->rx_len) { + u32 rxpkt1h = DSI_PORT_READ(RXPKT1H); + u8 *msg_rx = msg->rx_buf; + + if (rxpkt1h & DSI_RXPKT1H_PKT_TYPE_LONG) { + u32 rxlen = VC4_GET_FIELD(rxpkt1h, + DSI_RXPKT1H_BC_PARAM); + + if (rxlen != msg->rx_len) { + DRM_ERROR("DSI returned %db, expecting %db\n", + rxlen, (int)msg->rx_len); + ret = -ENXIO; + goto reset_fifo_and_return; + } + + for (i = 0; i < msg->rx_len; i++) + msg_rx[i] = DSI_READ(DSI1_RXPKT_FIFO); + } else { + /* FINISHME: Handle AWER */ + + msg_rx[0] = VC4_GET_FIELD(rxpkt1h, + DSI_RXPKT1H_SHORT_0); + if (msg->rx_len > 1) { + msg_rx[1] = VC4_GET_FIELD(rxpkt1h, + DSI_RXPKT1H_SHORT_1); + } + } + } + + return ret; + +reset_fifo_and_return: + DRM_ERROR("DSI transfer failed, resetting: %d\n", ret); + + DSI_PORT_WRITE(TXPKT1C, DSI_PORT_READ(TXPKT1C) & ~DSI_TXPKT1C_CMD_EN); + udelay(1); + DSI_PORT_WRITE(CTRL, + DSI_PORT_READ(CTRL) | + DSI_PORT_BIT(CTRL_RESET_FIFOS)); + + DSI_PORT_WRITE(TXPKT1C, 0); + DSI_PORT_WRITE(INT_EN, DSI1_INTERRUPTS_ALWAYS_ENABLED); + return ret; +} + +static int vc4_dsi_host_attach(struct mipi_dsi_host *host, + struct mipi_dsi_device *device) +{ + struct vc4_dsi *dsi = host_to_dsi(host); + int ret = 0; + + dsi->lanes = device->lanes; + dsi->channel = device->channel; + dsi->format = device->format; + dsi->mode_flags = device->mode_flags; + + if (!(dsi->mode_flags & MIPI_DSI_MODE_VIDEO)) { + dev_err(&dsi->pdev->dev, + "Only VIDEO mode panels supported currently.\n"); + return 0; + } + + dsi->panel = of_drm_find_panel(device->dev.of_node); + if (!dsi->panel) + return 0; + + ret = drm_panel_attach(dsi->panel, dsi->connector); + if (ret != 0) + return ret; + + drm_helper_hpd_irq_event(dsi->connector->dev); + + return 0; +} + +static int vc4_dsi_host_detach(struct mipi_dsi_host *host, + struct mipi_dsi_device *device) +{ + struct vc4_dsi *dsi = host_to_dsi(host); + + if (dsi->panel) { + int ret = drm_panel_detach(dsi->panel); + + if (ret) + return ret; + + dsi->panel = NULL; + + drm_helper_hpd_irq_event(dsi->connector->dev); + } + + return 0; +} + +static const struct mipi_dsi_host_ops vc4_dsi_host_ops = { + .attach = vc4_dsi_host_attach, + .detach = vc4_dsi_host_detach, + .transfer = vc4_dsi_host_transfer, +}; + +static const struct drm_encoder_helper_funcs vc4_dsi_encoder_helper_funcs = { + .disable = vc4_dsi_encoder_disable, + .enable = vc4_dsi_encoder_enable, +}; + +static const struct of_device_id vc4_dsi_dt_match[] = { + { .compatible = "brcm,bcm2835-dsi1", (void *)(uintptr_t)1 }, + {} +}; + +static void dsi_handle_error(struct vc4_dsi *dsi, + irqreturn_t *ret, u32 stat, u32 bit, + const char *type) +{ + if (!(stat & bit)) + return; + + DRM_ERROR("DSI%d: %s error\n", dsi->port, type); + *ret = IRQ_HANDLED; +} + +static irqreturn_t vc4_dsi_irq_handler(int irq, void *data) +{ + struct vc4_dsi *dsi = data; + u32 stat = DSI_PORT_READ(INT_STAT); + irqreturn_t ret = IRQ_NONE; + + DSI_PORT_WRITE(INT_STAT, stat); + + dsi_handle_error(dsi, &ret, stat, + DSI1_INT_ERR_SYNC_ESC, "LPDT sync"); + dsi_handle_error(dsi, &ret, stat, + DSI1_INT_ERR_CONTROL, "data lane 0 sequence"); + dsi_handle_error(dsi, &ret, stat, + DSI1_INT_ERR_CONT_LP0, "LP0 contention"); + dsi_handle_error(dsi, &ret, stat, + DSI1_INT_ERR_CONT_LP1, "LP1 contention"); + dsi_handle_error(dsi, &ret, stat, + DSI1_INT_HSTX_TO, "HSTX timeout"); + dsi_handle_error(dsi, &ret, stat, + DSI1_INT_LPRX_TO, "LPRX timeout"); + dsi_handle_error(dsi, &ret, stat, + DSI1_INT_TA_TO, "turnaround timeout"); + dsi_handle_error(dsi, &ret, stat, + DSI1_INT_PR_TO, "peripheral reset timeout"); + + if (stat & (DSI1_INT_TXPKT1_DONE | DSI1_INT_PHY_DIR_RTF)) { + complete(&dsi->xfer_completion); + ret = IRQ_HANDLED; + } else if (stat & DSI1_INT_HSTX_TO) { + complete(&dsi->xfer_completion); + dsi->xfer_result = -ETIMEDOUT; + ret = IRQ_HANDLED; + } + + return ret; +} + +/** + * Exposes clocks generated by the analog PHY that are consumed by + * CPRMAN (clk-bcm2835.c). + */ +static int +vc4_dsi_init_phy_clocks(struct vc4_dsi *dsi) +{ + struct device *dev = &dsi->pdev->dev; + const char *parent_name = __clk_get_name(dsi->pll_phy_clock); + static const struct { + const char *dsi0_name, *dsi1_name; + int div; + } phy_clocks[] = { + { "dsi0_byte", "dsi1_byte", 8 }, + { "dsi0_ddr2", "dsi1_ddr2", 4 }, + { "dsi0_ddr", "dsi1_ddr", 2 }, + }; + int i; + + dsi->clk_onecell.clk_num = ARRAY_SIZE(phy_clocks); + dsi->clk_onecell.clks = devm_kcalloc(dev, + dsi->clk_onecell.clk_num, + sizeof(*dsi->clk_onecell.clks), + GFP_KERNEL); + if (!dsi->clk_onecell.clks) + return -ENOMEM; + + for (i = 0; i < ARRAY_SIZE(phy_clocks); i++) { + struct clk_fixed_factor *fix = &dsi->phy_clocks[i]; + struct clk_init_data init; + struct clk *clk; + + /* We just use core fixed factor clock ops for the PHY + * clocks. The clocks are actually gated by the + * PHY_AFEC0_DDRCLK_EN bits, which we should be + * setting if we use the DDR/DDR2 clocks. However, + * vc4_dsi_encoder_enable() is setting up both AFEC0, + * setting both our parent DSI PLL's rate and this + * clock's rate, so it knows if DDR/DDR2 are going to + * be used and could enable the gates itself. + */ + fix->mult = 1; + fix->div = phy_clocks[i].div; + fix->hw.init = &init; + + memset(&init, 0, sizeof(init)); + init.parent_names = &parent_name; + init.num_parents = 1; + if (dsi->port == 1) + init.name = phy_clocks[i].dsi1_name; + else + init.name = phy_clocks[i].dsi0_name; + init.ops = &clk_fixed_factor_ops; + init.flags = CLK_IS_BASIC; + + clk = devm_clk_register(dev, &fix->hw); + if (IS_ERR(clk)) + return PTR_ERR(clk); + + dsi->clk_onecell.clks[i] = clk; + } + + return of_clk_add_provider(dev->of_node, + of_clk_src_onecell_get, + &dsi->clk_onecell); +} + +static int vc4_dsi_bind(struct device *dev, struct device *master, void *data) +{ + struct platform_device *pdev = to_platform_device(dev); + struct drm_device *drm = dev_get_drvdata(master); + struct vc4_dev *vc4 = to_vc4_dev(drm); + struct vc4_dsi *dsi; + struct vc4_dsi_encoder *vc4_dsi_encoder; + const struct of_device_id *match; + dma_cap_mask_t dma_mask; + int ret; + + dsi = devm_kzalloc(dev, sizeof(*dsi), GFP_KERNEL); + if (!dsi) + return -ENOMEM; + + match = of_match_device(vc4_dsi_dt_match, dev); + if (!match) + return -ENODEV; + + dsi->port = (uintptr_t)match->data; + + vc4_dsi_encoder = devm_kzalloc(dev, sizeof(*vc4_dsi_encoder), + GFP_KERNEL); + if (!vc4_dsi_encoder) + return -ENOMEM; + vc4_dsi_encoder->base.type = VC4_ENCODER_TYPE_DSI1; + vc4_dsi_encoder->dsi = dsi; + dsi->encoder = &vc4_dsi_encoder->base.base; + + dsi->pdev = pdev; + dsi->regs = vc4_ioremap_regs(pdev, 0); + if (IS_ERR(dsi->regs)) + return PTR_ERR(dsi->regs); + + if (DSI_PORT_READ(ID) != DSI_ID_VALUE) { + dev_err(dev, "Port returned 0x%08x for ID instead of 0x%08x\n", + DSI_PORT_READ(ID), DSI_ID_VALUE); + return -ENODEV; + } + + /* DSI1 has a broken AXI slave that doesn't respond to writes + * from the ARM. It does handle writes from the DMA engine, + * so set up a channel for talking to it. + */ + if (dsi->port == 1) { + dsi->reg_dma_mem = dma_alloc_coherent(dev, 4, + &dsi->reg_dma_paddr, + GFP_KERNEL); + if (!dsi->reg_dma_mem) { + DRM_ERROR("Failed to get DMA memory\n"); + return -ENOMEM; + } + + dma_cap_zero(dma_mask); + dma_cap_set(DMA_MEMCPY, dma_mask); + dsi->reg_dma_chan = dma_request_chan_by_mask(&dma_mask); + if (IS_ERR(dsi->reg_dma_chan)) { + ret = PTR_ERR(dsi->reg_dma_chan); + if (ret != -EPROBE_DEFER) + DRM_ERROR("Failed to get DMA channel: %d\n", + ret); + return ret; + } + + /* Get the physical address of the device's registers. The + * struct resource for the regs gives us the bus address + * instead. + */ + dsi->reg_paddr = be32_to_cpup(of_get_address(dev->of_node, + 0, NULL, NULL)); + } + + init_completion(&dsi->xfer_completion); + /* At startup enable error-reporting interrupts and nothing else. */ + DSI_PORT_WRITE(INT_EN, DSI1_INTERRUPTS_ALWAYS_ENABLED); + /* Clear any existing interrupt state. */ + DSI_PORT_WRITE(INT_STAT, DSI_PORT_READ(INT_STAT)); + + ret = devm_request_irq(dev, platform_get_irq(pdev, 0), + vc4_dsi_irq_handler, 0, "vc4 dsi", dsi); + if (ret) { + if (ret != -EPROBE_DEFER) + dev_err(dev, "Failed to get interrupt: %d\n", ret); + return ret; + } + + dsi->escape_clock = devm_clk_get(dev, "escape"); + if (IS_ERR(dsi->escape_clock)) { + ret = PTR_ERR(dsi->escape_clock); + if (ret != -EPROBE_DEFER) + dev_err(dev, "Failed to get escape clock: %d\n", ret); + return ret; + } + + dsi->pll_phy_clock = devm_clk_get(dev, "phy"); + if (IS_ERR(dsi->pll_phy_clock)) { + ret = PTR_ERR(dsi->pll_phy_clock); + if (ret != -EPROBE_DEFER) + dev_err(dev, "Failed to get phy clock: %d\n", ret); + return ret; + } + + dsi->pixel_clock = devm_clk_get(dev, "pixel"); + if (IS_ERR(dsi->pixel_clock)) { + ret = PTR_ERR(dsi->pixel_clock); + if (ret != -EPROBE_DEFER) + dev_err(dev, "Failed to get pixel clock: %d\n", ret); + return ret; + } + + /* The esc clock rate is supposed to always be 100Mhz. */ + ret = clk_set_rate(dsi->escape_clock, 100 * 1000000); + if (ret) { + dev_err(dev, "Failed to set esc clock: %d\n", ret); + return ret; + } + + ret = vc4_dsi_init_phy_clocks(dsi); + if (ret) + return ret; + + if (dsi->port == 1) + vc4->dsi1 = dsi; + + drm_encoder_init(drm, dsi->encoder, &vc4_dsi_encoder_funcs, + DRM_MODE_ENCODER_DSI, NULL); + drm_encoder_helper_add(dsi->encoder, &vc4_dsi_encoder_helper_funcs); + + dsi->connector = vc4_dsi_connector_init(drm, dsi); + if (IS_ERR(dsi->connector)) { + ret = PTR_ERR(dsi->connector); + goto err_destroy_encoder; + } + + dsi->dsi_host.ops = &vc4_dsi_host_ops; + dsi->dsi_host.dev = dev; + + mipi_dsi_host_register(&dsi->dsi_host); + + dev_set_drvdata(dev, dsi); + + pm_runtime_enable(dev); + + return 0; + +err_destroy_encoder: + vc4_dsi_encoder_destroy(dsi->encoder); + + return ret; +} + +static void vc4_dsi_unbind(struct device *dev, struct device *master, + void *data) +{ + struct drm_device *drm = dev_get_drvdata(master); + struct vc4_dev *vc4 = to_vc4_dev(drm); + struct vc4_dsi *dsi = dev_get_drvdata(dev); + + pm_runtime_disable(dev); + + vc4_dsi_connector_destroy(dsi->connector); + vc4_dsi_encoder_destroy(dsi->encoder); + + mipi_dsi_host_unregister(&dsi->dsi_host); + + clk_disable_unprepare(dsi->pll_phy_clock); + clk_disable_unprepare(dsi->escape_clock); + + if (dsi->port == 1) + vc4->dsi1 = NULL; +} + +static const struct component_ops vc4_dsi_ops = { + .bind = vc4_dsi_bind, + .unbind = vc4_dsi_unbind, +}; + +static int vc4_dsi_dev_probe(struct platform_device *pdev) +{ + return component_add(&pdev->dev, &vc4_dsi_ops); +} + +static int vc4_dsi_dev_remove(struct platform_device *pdev) +{ + component_del(&pdev->dev, &vc4_dsi_ops); + return 0; +} + +struct platform_driver vc4_dsi_driver = { + .probe = vc4_dsi_dev_probe, + .remove = vc4_dsi_dev_remove, + .driver = { + .name = "vc4_dsi", + .of_match_table = vc4_dsi_dt_match, + }, +};

This doesn't yet cover input, but the driver does get the display working when the firmware is disabled from talking to our I2C lines.

Signed-off-by: Eric Anholt eric@anholt.net --- .../display/panel/raspberrypi,touchscreen.txt | 45 ++++++++++++++++++++++ 1 file changed, 45 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/panel/raspberrypi,touchscreen.txt

diff --git a/Documentation/devicetree/bindings/display/panel/raspberrypi,touchscreen.txt b/Documentation/devicetree/bindings/display/panel/raspberrypi,touchscreen.txt new file mode 100644 index 000000000000..fd328c52706b --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/raspberrypi,touchscreen.txt @@ -0,0 +1,45 @@ +This binding covers the official 7" (800x480) Raspberry Pi touchscreen +panel. + +This DSI panel contains: + +- TC358762 DSI->DPI bridge +- Atmel microcontroller on I2C for power sequencing the DSI bridge and + controlling backlight +- Touchscreen controller on I2C for touch input + +and the binding currently covers the DSI display parts but not its +touch input. + +Required properties: +- compatible: Must be "raspberrypi,touchscreen" +- raspberrypi,touchscreen-bridge: + Handle to the I2C device for Atmel microcontroller + +Example: + +dsi1: dsi@7e700000 { + #address-cells = <1>; + #size-cells = <0>; + <...> + + pitouchscreen: panel@0 { + compatible = "raspberrypi,touchscreen"; + reg = <0>; + + raspberrypi,touchscreen-bridge = <&pitouchscreen_bridge>; + }; +}; + +i2c_dsi: i2c { + compatible = "i2c-gpio"; + #address-cells = <1>; + #size-cells = <0>; + gpios = <&gpio 28 0 + &gpio 29 0>; + + pitouchscreen_bridge: bridge@45 { + compatible = "raspberrypi,touchscreen-bridge-i2c"; + reg = <0x45>; + }; +};

This commit is not intended to be merged. Instead we will use overlays to enable the panel, and this commit is just a demo of how things get wired up.

Signed-off-by: Eric Anholt eric@anholt.net --- arch/arm/boot/dts/bcm283x.dtsi | 30 +++++++++++++++++++++++++++++- 1 file changed, 29 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi index 82a4eccfb3d8..e96d0f29759a 100644 --- a/arch/arm/boot/dts/bcm283x.dtsi +++ b/arch/arm/boot/dts/bcm283x.dtsi @@ -286,7 +286,12 @@ "dsi1_ddr2", "dsi1_ddr";

- status = "disabled"; + pitouchscreen: panel@0 { + compatible = "raspberrypi,touchscreen"; + reg = <0>; + + raspberrypi,touchscreen-bridge = <&pitouchscreen_bridge>; + }; };

i2c1: i2c@7e804000 { @@ -346,6 +351,29 @@ vc4: gpu { compatible = "brcm,bcm2835-vc4"; }; + + i2c_dsi: i2c { + /* We have to use i2c-gpio because the + * firmware is also polling another device + * using the only hardware I2C bus that could + * connect to these pins. + */ + compatible = "i2c-gpio"; + #address-cells = <1>; + #size-cells = <0>; + gpios = <&gpio 28 0 + &gpio 29 0>; + + pitouchscreen_bridge: bridge@45 { + compatible = "raspberrypi,touchscreen-bridge-i2c"; + reg = <0x45>; + }; + + pitouchscreen_touch: bridge@38 { + compatible = "raspberrypi,touchscreen-ts-i2c"; + reg = <0x38>; + }; + }; };

clocks {