The DSI node is not a bus and the children do not have unit addresses.
Reported-by: Vinod Koul vkoul@kernel.org Signed-off-by: Krzysztof Kozlowski krzysztof.kozlowski@linaro.org --- .../bindings/display/msm/dsi-controller-main.yaml | 7 ------- 1 file changed, 7 deletions(-)
diff --git a/Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml b/Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml index 7095ec3c890d..57f238f72326 100644 --- a/Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml +++ b/Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml @@ -51,10 +51,6 @@ properties: phy-names: const: dsi
- "#address-cells": true - - "#size-cells": true - syscon-sfpb: description: A phandle to mmss_sfpb syscon node (only for DSIv2). $ref: "/schemas/types.yaml#/definitions/phandle" @@ -154,9 +150,6 @@ examples: reg = <0x0ae94000 0x400>; reg-names = "dsi_ctrl";
- #address-cells = <1>; - #size-cells = <0>; - interrupt-parent = <&mdss>; interrupts = <4>;
On 28/03/2022 17:29, Krzysztof Kozlowski wrote:
The DSI node is not a bus and the children do not have unit addresses.
Eh, actually MIPI DSI is a serial bus, so address/size cells seem right and my patch is not correct.
Reported-by: Vinod Koul vkoul@kernel.org Signed-off-by: Krzysztof Kozlowski krzysztof.kozlowski@linaro.org
.../bindings/display/msm/dsi-controller-main.yaml | 7 ------- 1 file changed, 7 deletions(-)
diff --git a/Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml b/Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml index 7095ec3c890d..57f238f72326 100644 --- a/Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml +++ b/Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml @@ -51,10 +51,6 @@ properties: phy-names: const: dsi
- "#address-cells": true
- "#size-cells": true
- syscon-sfpb: description: A phandle to mmss_sfpb syscon node (only for DSIv2). $ref: "/schemas/types.yaml#/definitions/phandle"
@@ -154,9 +150,6 @@ examples: reg = <0x0ae94000 0x400>; reg-names = "dsi_ctrl";
#address-cells = <1>;#size-cells = <0>;interrupt-parent = <&mdss>; interrupts = <4>;
Best regards, Krzysztof
On Mon, 28 Mar 2022 at 18:30, Krzysztof Kozlowski krzysztof.kozlowski@linaro.org wrote:
The DSI node is not a bus and the children do not have unit addresses.
Reported-by: Vinod Koul vkoul@kernel.org Signed-off-by: Krzysztof Kozlowski krzysztof.kozlowski@linaro.org
NAK. DSI panels are children of the DSI device tree node with the reg = <0>; address. This is the convention used by other platforms too (see e.g. arch/arm64/boot/dts/freescale/imx8mq-evk.dts).
With the DSI split link it is possible to attach two panels to a single DSI host, so addresses are necessary.
.../bindings/display/msm/dsi-controller-main.yaml | 7 ------- 1 file changed, 7 deletions(-)
diff --git a/Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml b/Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml index 7095ec3c890d..57f238f72326 100644 --- a/Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml +++ b/Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml @@ -51,10 +51,6 @@ properties: phy-names: const: dsi
- "#address-cells": true
- "#size-cells": true
- syscon-sfpb: description: A phandle to mmss_sfpb syscon node (only for DSIv2). $ref: "/schemas/types.yaml#/definitions/phandle"
@@ -154,9 +150,6 @@ examples: reg = <0x0ae94000 0x400>; reg-names = "dsi_ctrl";
#address-cells = <1>;#size-cells = <0>;interrupt-parent = <&mdss>; interrupts = <4>;-- 2.32.0
On 28/03/2022 18:43, Dmitry Baryshkov wrote:
On Mon, 28 Mar 2022 at 18:30, Krzysztof Kozlowski krzysztof.kozlowski@linaro.org wrote:
The DSI node is not a bus and the children do not have unit addresses.
Reported-by: Vinod Koul vkoul@kernel.org Signed-off-by: Krzysztof Kozlowski krzysztof.kozlowski@linaro.org
NAK. DSI panels are children of the DSI device tree node with the reg = <0>; address. This is the convention used by other platforms too (see e.g. arch/arm64/boot/dts/freescale/imx8mq-evk.dts).
With the DSI split link it is possible to attach two panels to a single DSI host, so addresses are necessary.
Yes, I noticed it slightly after I sent the patch. :(
Best regards, Krzysztof
On 28-03-22, 19:43, Dmitry Baryshkov wrote:
On Mon, 28 Mar 2022 at 18:30, Krzysztof Kozlowski krzysztof.kozlowski@linaro.org wrote:
The DSI node is not a bus and the children do not have unit addresses.
Reported-by: Vinod Koul vkoul@kernel.org Signed-off-by: Krzysztof Kozlowski krzysztof.kozlowski@linaro.org
NAK. DSI panels are children of the DSI device tree node with the reg = <0>; address. This is the convention used by other platforms too (see e.g. arch/arm64/boot/dts/freescale/imx8mq-evk.dts).
So we should add reg = 0, i will update my dtsi fix
With the DSI split link it is possible to attach two panels to a single DSI host, so addresses are necessary.
.../bindings/display/msm/dsi-controller-main.yaml | 7 ------- 1 file changed, 7 deletions(-)
diff --git a/Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml b/Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml index 7095ec3c890d..57f238f72326 100644 --- a/Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml +++ b/Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml @@ -51,10 +51,6 @@ properties: phy-names: const: dsi
- "#address-cells": true
- "#size-cells": true
- syscon-sfpb: description: A phandle to mmss_sfpb syscon node (only for DSIv2). $ref: "/schemas/types.yaml#/definitions/phandle"
@@ -154,9 +150,6 @@ examples: reg = <0x0ae94000 0x400>; reg-names = "dsi_ctrl";
#address-cells = <1>;#size-cells = <0>;interrupt-parent = <&mdss>; interrupts = <4>;-- 2.32.0
-- With best wishes Dmitry
On 28/03/2022 19:16, Vinod Koul wrote:
On 28-03-22, 19:43, Dmitry Baryshkov wrote:
On Mon, 28 Mar 2022 at 18:30, Krzysztof Kozlowski krzysztof.kozlowski@linaro.org wrote:
The DSI node is not a bus and the children do not have unit addresses.
Reported-by: Vinod Koul vkoul@kernel.org Signed-off-by: Krzysztof Kozlowski krzysztof.kozlowski@linaro.org
NAK. DSI panels are children of the DSI device tree node with the reg = <0>; address. This is the convention used by other platforms too (see e.g. arch/arm64/boot/dts/freescale/imx8mq-evk.dts).
So we should add reg = 0, i will update my dtsi fix
To "ports" node? No. The reg=0 is for children of the bus, so the panels. How to combine both without warnings - ports and panel@0 - I don't know yet...
Best regards, Krzysztof
On Mon, Mar 28, 2022 at 12:18 PM Krzysztof Kozlowski krzysztof.kozlowski@linaro.org wrote:
On 28/03/2022 19:16, Vinod Koul wrote:
On 28-03-22, 19:43, Dmitry Baryshkov wrote:
On Mon, 28 Mar 2022 at 18:30, Krzysztof Kozlowski krzysztof.kozlowski@linaro.org wrote:
The DSI node is not a bus and the children do not have unit addresses.
Reported-by: Vinod Koul vkoul@kernel.org Signed-off-by: Krzysztof Kozlowski krzysztof.kozlowski@linaro.org
NAK. DSI panels are children of the DSI device tree node with the reg = <0>; address. This is the convention used by other platforms too (see e.g. arch/arm64/boot/dts/freescale/imx8mq-evk.dts).
So we should add reg = 0, i will update my dtsi fix
To "ports" node? No. The reg=0 is for children of the bus, so the panels. How to combine both without warnings - ports and panel@0 - I don't know yet...
I don't think that should case a warning. Or at least it's one we turn off.
Rob
On 28-03-22, 13:21, Rob Herring wrote:
On Mon, Mar 28, 2022 at 12:18 PM Krzysztof Kozlowski krzysztof.kozlowski@linaro.org wrote:
On 28/03/2022 19:16, Vinod Koul wrote:
On 28-03-22, 19:43, Dmitry Baryshkov wrote:
On Mon, 28 Mar 2022 at 18:30, Krzysztof Kozlowski krzysztof.kozlowski@linaro.org wrote:
The DSI node is not a bus and the children do not have unit addresses.
Reported-by: Vinod Koul vkoul@kernel.org Signed-off-by: Krzysztof Kozlowski krzysztof.kozlowski@linaro.org
NAK. DSI panels are children of the DSI device tree node with the reg = <0>; address. This is the convention used by other platforms too (see e.g. arch/arm64/boot/dts/freescale/imx8mq-evk.dts).
So we should add reg = 0, i will update my dtsi fix
To "ports" node? No. The reg=0 is for children of the bus, so the panels. How to combine both without warnings - ports and panel@0 - I don't know yet...
I don't think that should case a warning. Or at least it's one we turn off.
Well in this case I think we might need a fix: Here is the example quoted in the binding. We have ports{} and then the two port@0 and port@1 underneath.
So it should be okay to drop #address-cells/#size-cells from dsi node but keep in ports node...
Thoughts...?
dsi@ae94000 { compatible = "qcom,mdss-dsi-ctrl"; reg = <0x0ae94000 0x400>; reg-names = "dsi_ctrl";
#address-cells = <1>; #size-cells = <0>;
interrupt-parent = <&mdss>; interrupts = <4>;
clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>, <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>, <&dispcc DISP_CC_MDSS_PCLK0_CLK>, <&dispcc DISP_CC_MDSS_ESC0_CLK>, <&dispcc DISP_CC_MDSS_AHB_CLK>, <&dispcc DISP_CC_MDSS_AXI_CLK>; clock-names = "byte", "byte_intf", "pixel", "core", "iface", "bus";
phys = <&dsi0_phy>; phy-names = "dsi";
assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>; assigned-clock-parents = <&dsi_phy 0>, <&dsi_phy 1>;
power-domains = <&rpmhpd SC7180_CX>; operating-points-v2 = <&dsi_opp_table>;
ports { #address-cells = <1>; #size-cells = <0>;
port@0 { reg = <0>; dsi0_in: endpoint { remote-endpoint = <&dpu_intf1_out>; }; };
port@1 { reg = <1>; dsi0_out: endpoint { remote-endpoint = <&sn65dsi86_in>; data-lanes = <0 1 2 3>; }; }; }; };
Rob
On Tue, Mar 29, 2022 at 12:01:52PM +0530, Vinod Koul wrote:
On 28-03-22, 13:21, Rob Herring wrote:
On Mon, Mar 28, 2022 at 12:18 PM Krzysztof Kozlowski krzysztof.kozlowski@linaro.org wrote:
On 28/03/2022 19:16, Vinod Koul wrote:
On 28-03-22, 19:43, Dmitry Baryshkov wrote:
On Mon, 28 Mar 2022 at 18:30, Krzysztof Kozlowski krzysztof.kozlowski@linaro.org wrote:
The DSI node is not a bus and the children do not have unit addresses.
Reported-by: Vinod Koul vkoul@kernel.org Signed-off-by: Krzysztof Kozlowski krzysztof.kozlowski@linaro.org
NAK. DSI panels are children of the DSI device tree node with the reg = <0>; address. This is the convention used by other platforms too (see e.g. arch/arm64/boot/dts/freescale/imx8mq-evk.dts).
So we should add reg = 0, i will update my dtsi fix
To "ports" node? No. The reg=0 is for children of the bus, so the panels. How to combine both without warnings - ports and panel@0 - I don't know yet...
I don't think that should case a warning. Or at least it's one we turn off.
Well in this case I think we might need a fix: Here is the example quoted in the binding. We have ports{} and then the two port@0 and port@1 underneath.
It's the #address-cells/#size-cells under 'ports' that applies to 'port' nodes. As 'ports' has no address (reg) itself, it doesn't need #address-cells/#size-cells in its parent node.
So it should be okay to drop #address-cells/#size-cells from dsi node but keep in ports node...
Yes.
Thoughts...?
But I thought a panel@0 node was being added? If so then you need to add them back.
Rob
On 29-03-22, 10:52, Rob Herring wrote:
On Tue, Mar 29, 2022 at 12:01:52PM +0530, Vinod Koul wrote:
On 28-03-22, 13:21, Rob Herring wrote:
On Mon, Mar 28, 2022 at 12:18 PM Krzysztof Kozlowski krzysztof.kozlowski@linaro.org wrote:
On 28/03/2022 19:16, Vinod Koul wrote:
On 28-03-22, 19:43, Dmitry Baryshkov wrote:
On Mon, 28 Mar 2022 at 18:30, Krzysztof Kozlowski krzysztof.kozlowski@linaro.org wrote: > > The DSI node is not a bus and the children do not have unit addresses. > > Reported-by: Vinod Koul vkoul@kernel.org > Signed-off-by: Krzysztof Kozlowski krzysztof.kozlowski@linaro.org
NAK. DSI panels are children of the DSI device tree node with the reg = <0>; address. This is the convention used by other platforms too (see e.g. arch/arm64/boot/dts/freescale/imx8mq-evk.dts).
So we should add reg = 0, i will update my dtsi fix
To "ports" node? No. The reg=0 is for children of the bus, so the panels. How to combine both without warnings - ports and panel@0 - I don't know yet...
I don't think that should case a warning. Or at least it's one we turn off.
Well in this case I think we might need a fix: Here is the example quoted in the binding. We have ports{} and then the two port@0 and port@1 underneath.
It's the #address-cells/#size-cells under 'ports' that applies to 'port' nodes. As 'ports' has no address (reg) itself, it doesn't need #address-cells/#size-cells in its parent node.
So it should be okay to drop #address-cells/#size-cells from dsi node but keep in ports node...
Yes.
Thoughts...?
But I thought a panel@0 node was being added? If so then you need to add them back.
I guess we should make this optional, keep it when adding panel@0 node and skip for rest where not applicable..? Dmitry is that fine with you?
On Thu, 31 Mar 2022 at 09:05, Vinod Koul vkoul@kernel.org wrote:
On 29-03-22, 10:52, Rob Herring wrote:
On Tue, Mar 29, 2022 at 12:01:52PM +0530, Vinod Koul wrote:
On 28-03-22, 13:21, Rob Herring wrote:
On Mon, Mar 28, 2022 at 12:18 PM Krzysztof Kozlowski krzysztof.kozlowski@linaro.org wrote:
On 28/03/2022 19:16, Vinod Koul wrote:
On 28-03-22, 19:43, Dmitry Baryshkov wrote: > On Mon, 28 Mar 2022 at 18:30, Krzysztof Kozlowski > krzysztof.kozlowski@linaro.org wrote: >> >> The DSI node is not a bus and the children do not have unit addresses. >> >> Reported-by: Vinod Koul vkoul@kernel.org >> Signed-off-by: Krzysztof Kozlowski krzysztof.kozlowski@linaro.org > > NAK. > DSI panels are children of the DSI device tree node with the reg = <0>; address. > This is the convention used by other platforms too (see e.g. > arch/arm64/boot/dts/freescale/imx8mq-evk.dts).
So we should add reg = 0, i will update my dtsi fix
To "ports" node? No. The reg=0 is for children of the bus, so the panels. How to combine both without warnings - ports and panel@0 - I don't know yet...
I don't think that should case a warning. Or at least it's one we turn off.
Well in this case I think we might need a fix: Here is the example quoted in the binding. We have ports{} and then the two port@0 and port@1 underneath.
It's the #address-cells/#size-cells under 'ports' that applies to 'port' nodes. As 'ports' has no address (reg) itself, it doesn't need #address-cells/#size-cells in its parent node.
So it should be okay to drop #address-cells/#size-cells from dsi node but keep in ports node...
Yes.
Thoughts...?
But I thought a panel@0 node was being added? If so then you need to add them back.
I guess we should make this optional, keep it when adding panel@0 node and skip for rest where not applicable..? Dmitry is that fine with you?
This sounds like a workaround. When a panel node is added together with the '#address-cells' / '#size-cells' properties, we will get warnings for the 'ports' node. I'd prefer to leave things to pinpoint that the problem is generic rather than being specific to several device trees with the DSI panel nodes. How do other platforms solve the issue?
In fact we can try shifting to the following dts schema:
dsi@ae940000 { compatible = "qcom,mdss-dsi-ctrl";
ports { #adress-cells = <1>; #size-cells = <0>; port@0 { reg = <0>; dsi0_in: endpoint {}; }; port@1 { reg = <1>; dsi0_out: endpoint { remote-endpoint = <&panel_in>; }; };
/* dsi-bus is a generic part */ dsi-bus { #adress-cells = <1>; #size-cells = <0>; /* panel@0 goes to the board file */ panel@0 { compatible = "vendor,some-panel"; ports { #adress-cells = <1>; #size-cells = <0>; port@0 { reg = <0>; panel_in: endpoint { remote-endpoint = <&dsi0_out>; }; }; }; }; };
WDYT?
On Thu, Mar 31, 2022 at 4:35 AM Dmitry Baryshkov dmitry.baryshkov@linaro.org wrote:
On Thu, 31 Mar 2022 at 09:05, Vinod Koul vkoul@kernel.org wrote:
On 29-03-22, 10:52, Rob Herring wrote:
On Tue, Mar 29, 2022 at 12:01:52PM +0530, Vinod Koul wrote:
On 28-03-22, 13:21, Rob Herring wrote:
On Mon, Mar 28, 2022 at 12:18 PM Krzysztof Kozlowski krzysztof.kozlowski@linaro.org wrote:
On 28/03/2022 19:16, Vinod Koul wrote: > On 28-03-22, 19:43, Dmitry Baryshkov wrote: >> On Mon, 28 Mar 2022 at 18:30, Krzysztof Kozlowski >> krzysztof.kozlowski@linaro.org wrote: >>> >>> The DSI node is not a bus and the children do not have unit addresses. >>> >>> Reported-by: Vinod Koul vkoul@kernel.org >>> Signed-off-by: Krzysztof Kozlowski krzysztof.kozlowski@linaro.org >> >> NAK. >> DSI panels are children of the DSI device tree node with the reg = <0>; address. >> This is the convention used by other platforms too (see e.g. >> arch/arm64/boot/dts/freescale/imx8mq-evk.dts). > > So we should add reg = 0, i will update my dtsi fix >
To "ports" node? No. The reg=0 is for children of the bus, so the panels. How to combine both without warnings - ports and panel@0 - I don't know yet...
I don't think that should case a warning. Or at least it's one we turn off.
Well in this case I think we might need a fix: Here is the example quoted in the binding. We have ports{} and then the two port@0 and port@1 underneath.
It's the #address-cells/#size-cells under 'ports' that applies to 'port' nodes. As 'ports' has no address (reg) itself, it doesn't need #address-cells/#size-cells in its parent node.
So it should be okay to drop #address-cells/#size-cells from dsi node but keep in ports node...
Yes.
Thoughts...?
But I thought a panel@0 node was being added? If so then you need to add them back.
I guess we should make this optional, keep it when adding panel@0 node and skip for rest where not applicable..? Dmitry is that fine with you?
This sounds like a workaround. When a panel node is added together with the '#address-cells' / '#size-cells' properties, we will get warnings for the 'ports' node.
What warning exactly? Is that with W=1?
Some warnings are more "don't do this on new designs" rather than never allowed and need to fix current bindings/dts. As such, these warnings will probably never be enabled by default.
Rob
dri-devel@lists.freedesktop.org
-
Dmitry Baryshkov -
Krzysztof Kozlowski -
Rob Herring -
Rob Herring -
Vinod Koul