There is a display controller in loongson's LS2K1000 SoC and LS7A1000 bridge, and the DC in those chip is a PCI device. This display controller have two display pipes but with only one hardware cursor. Each way has a DVO output interface and the CRTC is able to scanout from 1920x1080 resolution at 60Hz. LS2K1000 is a SoC, only system memory is available. Therefore scanout form system memory is the only choice and we prefer the cma helper base solution even through it is possible to use VRAM helper base solution on ls2k1000 by carving out part of system memory as VRAM.
The dc in ls7a1000 can scanout from both the system memory and the dedicate VRAM attached to the ddr3 memory controller. Sadly, only scanout from the VRAM is proved to be a reliable solution for massive product. Scanout from the system memory suffer from some hardware deficiency which cause the screen flickering under RAM pressure. This is the reason why we integrate two distict helpers into one piece of device driver.
+------+ | DDR4 | +------+ || MC0 +-----------------------+------------+ +----------+ Hyper | LS7A1000 | DDR3 | +------+ | LS3A4000 |<--------->| +--------+ +-------+ | memory |<->| VRAM | | CPU |<--------->| | GC1000 | | LSDC | | controller | +------+ +----------+ Transport | +--------+ +-+---+-+ +------------| || MC1 +---------------|---|----------------+ +------+ | | | DDR4 | +-------+ DVO0 | | DVO1 +------+ +------+ VGA <--|ADV7125|<---------+ +------->|TFP410|--> DVI/HDMI +-------+ +------+
The above picture give a simple usage of LS7A1000, note that the encoder is not necessary adv7125 or tfp410, it is a choice of the downstream board manufacturer. Other candicate encoder can be ch7034b, sil9022 and ite66121 etc. This is the reason why we still need device tree to provide board specific information. Beside, the dc in both LS2L1000 and LS7A1000 have the vendor:device id of 0x0014:0x7a06. even the reverison id is also same. We can't tell it apart simply(this is the firmware engineer's mistake). But firmware already flushed to the board and sold out, so we resolve those issues by using the device tree which already have certain support.
Nevertheless, this patch try to provided a minimal support for this display controller which is mainly for graphic environment bring up. Hope that the code can speak for itself.
For LS7A1000, there are 4 gpios who register is located at dc register space which is used to emulation i2c. LS2K1000 and LS2K0500 SoC don't have those hardware, they use general purpose gpio or hardware i2c to serve this purpose. For ladc, there is only a 1:1 mapping of encoders and connectors.
+-------------------+ _________ | | | | | CRTC0 --> DVO0 ---------> Encoder0 --> Connector0 ---> | Monotor | | | ^ ^ |_________| | | | | | <----- i2c0 ----------------+ | LSDC IP CORE | | <----- i2c1 ----------------+ | | | | _________ | | | | | | | CRTC1 --> DVO1 ---------> Encoder1 --> Connector1 ---> | Panel | | | |_________| +-------------------+
Below is a brief introduction of loongson's CPU, bridge chip and SoC. LS2K1000 is a double core 1.0Ghz mips64r2 compatible SoC[1]. LS7A1000 is a bridge chip made by Loongson corporation which act as north and/or south bridge of loongson's desktop and server level processor. It is equivalent to RS780E or something like that. More details can be read from its user manual[2].
This bridge chip is typically use with LS3A3000, LS3A4000 and LS3A5000 cpu. LS3A3000 is 4 core 1.45gHz mips64r2 compatible cpu. LS3A4000 is 4 core 1.8gHz mips64r5 compatible cpu. LS3A5000 is 4 core 2.5gHz loongarch cpu[3].
v2: fixup warnings reported by kernel test robot
v3: fix more grammar mistakes in Kconfig reported by Randy Dunlap and give more details about lsdc.
v4: 1) Add dts required and explain why device tree is required. 2) Give more description about lsdc and vram helper base driver. 3) Fix warnings reported by kernel test robot. 4) Introduce stride_alignment member into struct lsdc_chip_desc, the stride alignment is 256 bytes for ls7a1000, ls2k1000 and ls2k0500 SoC. But ls7a2000 improve it to 32 bytes, We are prepare for extend the support for the on coming device.
v5: 1) using writel and readl replace writeq and readq, to fix kernel test robot report build error on other archtecture 2) set default fb format to XRGB8888 at crtc reset time. 3) fix typos.
[1] https://wiki.debian.org/InstallingDebianOn/Lemote/Loongson2K1000 [2] https://loongson.github.io/LoongArch-Documentation/Loongson-7A1000-usermanua... [3] https://loongson.github.io/LoongArch-Documentation/Loongson-3A5000-usermanua...
Reported-by: Randy Dunlap rdunlap@infradead.org Reported-by: kernel test robot Signed-off-by: suijingfeng suijingfeng@loongson.cn Signed-off-by: Sui Jingfeng 15330273260@189.cn
suijingfeng (3): drm/lsdc: add drm driver for loongson display controller dt-bindings: ls2k1000: add the display controller device node dt-bindings: mips: loongson: introduce board specific dts
arch/mips/boot/dts/loongson/lemote_a1901.dts | 64 ++ .../boot/dts/loongson/loongson64-2k1000.dtsi | 11 + .../boot/dts/loongson/ls3a4000_7a1000_evb.dts | 68 ++ arch/mips/boot/dts/loongson/ls7a-pch.dtsi | 2 +- drivers/gpu/drm/Kconfig | 2 + drivers/gpu/drm/Makefile | 1 + drivers/gpu/drm/lsdc/Kconfig | 38 + drivers/gpu/drm/lsdc/Makefile | 15 + drivers/gpu/drm/lsdc/lsdc_connector.c | 439 +++++++++ drivers/gpu/drm/lsdc/lsdc_connector.h | 60 ++ drivers/gpu/drm/lsdc/lsdc_crtc.c | 440 +++++++++ drivers/gpu/drm/lsdc/lsdc_drv.c | 845 ++++++++++++++++++ drivers/gpu/drm/lsdc/lsdc_drv.h | 216 +++++ drivers/gpu/drm/lsdc/lsdc_encoder.c | 79 ++ drivers/gpu/drm/lsdc/lsdc_i2c.c | 220 +++++ drivers/gpu/drm/lsdc/lsdc_i2c.h | 61 ++ drivers/gpu/drm/lsdc/lsdc_irq.c | 77 ++ drivers/gpu/drm/lsdc/lsdc_irq.h | 37 + drivers/gpu/drm/lsdc/lsdc_plane.c | 681 ++++++++++++++ drivers/gpu/drm/lsdc/lsdc_pll.c | 657 ++++++++++++++ drivers/gpu/drm/lsdc/lsdc_pll.h | 109 +++ drivers/gpu/drm/lsdc/lsdc_regs.h | 246 +++++ 22 files changed, 4367 insertions(+), 1 deletion(-) create mode 100644 arch/mips/boot/dts/loongson/lemote_a1901.dts create mode 100644 arch/mips/boot/dts/loongson/ls3a4000_7a1000_evb.dts create mode 100644 drivers/gpu/drm/lsdc/Kconfig create mode 100644 drivers/gpu/drm/lsdc/Makefile create mode 100644 drivers/gpu/drm/lsdc/lsdc_connector.c create mode 100644 drivers/gpu/drm/lsdc/lsdc_connector.h create mode 100644 drivers/gpu/drm/lsdc/lsdc_crtc.c create mode 100644 drivers/gpu/drm/lsdc/lsdc_drv.c create mode 100644 drivers/gpu/drm/lsdc/lsdc_drv.h create mode 100644 drivers/gpu/drm/lsdc/lsdc_encoder.c create mode 100644 drivers/gpu/drm/lsdc/lsdc_i2c.c create mode 100644 drivers/gpu/drm/lsdc/lsdc_i2c.h create mode 100644 drivers/gpu/drm/lsdc/lsdc_irq.c create mode 100644 drivers/gpu/drm/lsdc/lsdc_irq.h create mode 100644 drivers/gpu/drm/lsdc/lsdc_plane.c create mode 100644 drivers/gpu/drm/lsdc/lsdc_pll.c create mode 100644 drivers/gpu/drm/lsdc/lsdc_pll.h create mode 100644 drivers/gpu/drm/lsdc/lsdc_regs.h
From: suijingfeng suijingfeng@loongson.cn
There is a display controller in loongson's LS2K1000 SoC and LS7A1000 bridge, and the DC in those chip is a PCI device. This display controller have two display pipes but with only one hardware cursor. Each way has a DVO output interface and the CRTC is able to scanout from 1920x1080 resolution at 60Hz. LS2K1000 is a SoC, only system memory is available. Therefore scanout form system memory is the only choice and we prefer the cma helper base solution even through it is possible to use VRAM helper base solution on ls2k1000 by carving out part of system memory as VRAM.
The dc in ls7a1000 can scanout from both the system memory and the dedicate VRAM attached to the ddr3 memory controller. Sadly, only scanout from the VRAM is proved to be a reliable solution for massive product. Scanout from the system memory suffer from some hardware deficiency which cause the screen flickering under RAM pressure. This is the reason why we integrate two distict helpers into one piece of device driver.
+------+ | DDR4 | +------+ || MC0 +-----------------------+------------+ +----------+ Hyper | LS7A1000 | DDR3 | +------+ | LS3A4000 |<--------->| +--------+ +-------+ | memory |<->| VRAM | | CPU |<--------->| | GC1000 | | LSDC | | controller | +------+ +----------+ Transport | +--------+ +-+---+-+ +------------| || MC1 +---------------|---|----------------+ +------+ | | | DDR4 | +-------+ DVO0 | | DVO1 +------+ +------+ VGA <--|ADV7125|<---------+ +------->|TFP410|--> DVI/HDMI +-------+ +------+
The above picture give a simple usage of LS7A1000, note that the encoder is not necessary adv7125 or tfp410, it is a choice of the downstream board manufacturer. Other candicate encoder can be ch7034b, sil9022 and ite66121 etc. This is the reason why we still need device tree to provide board specific information. Beside, the dc in both ls2k1000 and ls7k1000 have the vendor:device id of 0x0014:0x7a06. even the reverison id is also same. We can't tell it apart simply(this is the firmware engineer's mistake). But firmware already flushed to the board and sold out, so we resolve those issues by using the device tree which already have certain support.
Nevertheless, this patch try to provided a minimal support for this display controller which is mainly for graphic environment bring up. Hope that the code can speak for itself.
For ls7a1000, there are 4 gpios who register is located at dc register space which is used to emulation i2c. LS2K1000 and LS2K0500 SoC don't have those hardware, they use general purpose gpio or hardware i2c to serve this purpose. For ladc, there is only a 1:1 mapping of encoders and connectors.
+-------------------+ _________ | | | | | CRTC0 --> DVO0 ---------> Encoder0 --> Connector0 ---> | Monotor | | | ^ ^ |_________| | | | | | <----- i2c0 ----------------+ | LSDC IP CORE | | <----- i2c1 ----------------+ | | | | _________ | | | | | | | CRTC1 --> DVO1 ---------> Encoder1 --> Connector1 ---> | Panel | | | |_________| +-------------------+
Below is a brief introduction of loongson's CPU, bridge chip and SoC. LS2K1000 is a double core 1.0Ghz mips64r2 compatible SoC[1]. LS7A1000 is a bridge chip made by Loongson corporation which act as north and/or south bridge of loongson's desktop and server level processor. It is equivalent to RS780E or something like that. More details can be read from its user manual[2].
This bridge chip is typically use with LS3A3000, LS3A4000 and LS3A5000 cpu. LS3A3000 is 4 core 1.45gHz mips64r2 compatible cpu. LS3A4000 is 4 core 1.8gHz mips64r5 compatible cpu. LS3A5000 is 4 core 2.5gHz loongarch cpu[3].
v2: fixup warnings reported by kernel test robot
v3: fix more grammar mistakes in Kconfig reported by Randy Dunlap and give more details about lsdc.
v4: 1) Add dts required and explain why device tree is required. 2) Give more description about lsdc and vram helper base driver. 3) Fix warnings reported by kernel test robot. 4) Introduce stride_alignment member into struct lsdc_chip_desc, the stride alignment is 256 bytes for ls7a1000, ls2k1000 and ls2k0500 SoC. But ls7a2000 improve it to 32 bytes, We are prepare for extend the support for the on coming device.
v5: 1) using writel and readl replace writeq and readq, to fix kernel test robot report build error on other archtecture 2) set default fb format to XRGB8888 at crtc reset time. 3) fix typos.
[1] https://wiki.debian.org/InstallingDebianOn/Lemote/Loongson2K1000 [2] https://loongson.github.io/LoongArch-Documentation/Loongson-7A1000-usermanua... [3] https://loongson.github.io/LoongArch-Documentation/Loongson-3A5000-usermanua...
Reported-by: Randy Dunlap rdunlap@infradead.org Reported-by: kernel test robot Signed-off-by: suijingfeng suijingfeng@loongson.cn Signed-off-by: Sui Jingfeng 15330273260@189.cn --- drivers/gpu/drm/Kconfig | 2 + drivers/gpu/drm/Makefile | 1 + drivers/gpu/drm/lsdc/Kconfig | 38 ++ drivers/gpu/drm/lsdc/Makefile | 15 + drivers/gpu/drm/lsdc/lsdc_connector.c | 439 +++++++++++++ drivers/gpu/drm/lsdc/lsdc_connector.h | 60 ++ drivers/gpu/drm/lsdc/lsdc_crtc.c | 440 ++++++++++++++ drivers/gpu/drm/lsdc/lsdc_drv.c | 845 ++++++++++++++++++++++++++ drivers/gpu/drm/lsdc/lsdc_drv.h | 216 +++++++ drivers/gpu/drm/lsdc/lsdc_encoder.c | 79 +++ drivers/gpu/drm/lsdc/lsdc_i2c.c | 220 +++++++ drivers/gpu/drm/lsdc/lsdc_i2c.h | 61 ++ drivers/gpu/drm/lsdc/lsdc_irq.c | 77 +++ drivers/gpu/drm/lsdc/lsdc_irq.h | 37 ++ drivers/gpu/drm/lsdc/lsdc_plane.c | 681 +++++++++++++++++++++ drivers/gpu/drm/lsdc/lsdc_pll.c | 657 ++++++++++++++++++++ drivers/gpu/drm/lsdc/lsdc_pll.h | 109 ++++ drivers/gpu/drm/lsdc/lsdc_regs.h | 246 ++++++++ 18 files changed, 4223 insertions(+) create mode 100644 drivers/gpu/drm/lsdc/Kconfig create mode 100644 drivers/gpu/drm/lsdc/Makefile create mode 100644 drivers/gpu/drm/lsdc/lsdc_connector.c create mode 100644 drivers/gpu/drm/lsdc/lsdc_connector.h create mode 100644 drivers/gpu/drm/lsdc/lsdc_crtc.c create mode 100644 drivers/gpu/drm/lsdc/lsdc_drv.c create mode 100644 drivers/gpu/drm/lsdc/lsdc_drv.h create mode 100644 drivers/gpu/drm/lsdc/lsdc_encoder.c create mode 100644 drivers/gpu/drm/lsdc/lsdc_i2c.c create mode 100644 drivers/gpu/drm/lsdc/lsdc_i2c.h create mode 100644 drivers/gpu/drm/lsdc/lsdc_irq.c create mode 100644 drivers/gpu/drm/lsdc/lsdc_irq.h create mode 100644 drivers/gpu/drm/lsdc/lsdc_plane.c create mode 100644 drivers/gpu/drm/lsdc/lsdc_pll.c create mode 100644 drivers/gpu/drm/lsdc/lsdc_pll.h create mode 100644 drivers/gpu/drm/lsdc/lsdc_regs.h
diff --git a/drivers/gpu/drm/Kconfig b/drivers/gpu/drm/Kconfig index dfdd3ec5f793..18de1485e2ed 100644 --- a/drivers/gpu/drm/Kconfig +++ b/drivers/gpu/drm/Kconfig @@ -405,6 +405,8 @@ source "drivers/gpu/drm/gud/Kconfig"
source "drivers/gpu/drm/sprd/Kconfig"
+source "drivers/gpu/drm/lsdc/Kconfig" + config DRM_HYPERV tristate "DRM Support for Hyper-V synthetic video device" depends on DRM && PCI && MMU && HYPERV diff --git a/drivers/gpu/drm/Makefile b/drivers/gpu/drm/Makefile index 8675c2af7ae1..2c5a76ced323 100644 --- a/drivers/gpu/drm/Makefile +++ b/drivers/gpu/drm/Makefile @@ -133,3 +133,4 @@ obj-y += xlnx/ obj-y += gud/ obj-$(CONFIG_DRM_HYPERV) += hyperv/ obj-$(CONFIG_DRM_SPRD) += sprd/ +obj-$(CONFIG_DRM_LSDC) += lsdc/ diff --git a/drivers/gpu/drm/lsdc/Kconfig b/drivers/gpu/drm/lsdc/Kconfig new file mode 100644 index 000000000000..7ed1b0fdbe1b --- /dev/null +++ b/drivers/gpu/drm/lsdc/Kconfig @@ -0,0 +1,38 @@ +config DRM_LSDC + tristate "DRM Support for loongson's display controller" + depends on DRM && PCI + depends on MACH_LOONGSON64 || LOONGARCH || MIPS || COMPILE_TEST + select OF + select CMA if HAVE_DMA_CONTIGUOUS + select DMA_CMA if HAVE_DMA_CONTIGUOUS + select DRM_KMS_HELPER + select DRM_KMS_FB_HELPER + select DRM_GEM_CMA_HELPER + select VIDEOMODE_HELPERS + select BACKLIGHT_PWM if CPU_LOONGSON2K + select I2C_GPIO if CPU_LOONGSON2K + select I2C_LS2X if CPU_LOONGSON2K + default m + help + This is a KMS driver for the display controller in the LS7A1000 + bridge chip and LS2K1000 SoC. The display controller has two + display pipes and it is a PCI device. + When using this driver on LS2K1000/LS2K0500 SoC, its framebuffer + is located at system memory. + If "M" is selected, the module will be called lsdc. + + If in doubt, say "Y". + +config DRM_LSDC_VRAM_DRIVER + bool "vram helper based device driver support" + depends on DRM_LSDC + select DRM_VRAM_HELPER + default y + help + When using this driver on LS7A1000 + LS3A3000/LS3A4000/LS3A5000 + platform, the LS7A1000 bridge chip has dedicated video RAM. Using + "lsdc.use_vram_helper=1" in the kernel command line will enable + this driver mode and then the framebuffer will be located at the + VRAM at the price of losing PRIME support. + + If in doubt, say "Y". diff --git a/drivers/gpu/drm/lsdc/Makefile b/drivers/gpu/drm/lsdc/Makefile new file mode 100644 index 000000000000..342990654478 --- /dev/null +++ b/drivers/gpu/drm/lsdc/Makefile @@ -0,0 +1,15 @@ +# +# Makefile for the lsdc drm device driver. +# + +lsdc-y := \ + lsdc_drv.o \ + lsdc_crtc.o \ + lsdc_irq.o \ + lsdc_plane.o \ + lsdc_pll.o \ + lsdc_i2c.o \ + lsdc_encoder.o \ + lsdc_connector.o + +obj-$(CONFIG_DRM_LSDC) += lsdc.o diff --git a/drivers/gpu/drm/lsdc/lsdc_connector.c b/drivers/gpu/drm/lsdc/lsdc_connector.c new file mode 100644 index 000000000000..7c527c62a3f0 --- /dev/null +++ b/drivers/gpu/drm/lsdc/lsdc_connector.c @@ -0,0 +1,439 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2020 Loongson Corporation + * + * Permission is hereby granted, free of charge, to any person obtaining a + * copy of this software and associated documentation files (the + * "Software"), to deal in the Software without restriction, including + * without limitation the rights to use, copy, modify, merge, publish, + * distribute, sub license, and/or sell copies of the Software, and to + * permit persons to whom the Software is furnished to do so, subject to + * the following conditions: + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IN NO EVENT SHALL + * THE COPYRIGHT HOLDERS, AUTHORS AND/OR ITS SUPPLIERS BE LIABLE FOR ANY CLAIM, + * DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR + * OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE + * USE OR OTHER DEALINGS IN THE SOFTWARE. + * + * The above copyright notice and this permission notice (including the + * next paragraph) shall be included in all copies or substantial portions + * of the Software. + */ + +/* + * Authors: + * Sui Jingfeng suijingfeng@loongson.cn + */ + +#include <drm/drm_print.h> +#include <drm/drm_edid.h> +#include <drm/drm_probe_helper.h> +#include <drm/drm_atomic_helper.h> +#include <drm/drm_crtc_helper.h> +#include <drm/drm_connector.h> + +#include <video/videomode.h> +#include <video/of_display_timing.h> + +#include "lsdc_drv.h" +#include "lsdc_i2c.h" +#include "lsdc_connector.h" + + +static int lsdc_get_modes_from_edid(struct drm_connector *connector) +{ + struct drm_device *ddev = connector->dev; + struct lsdc_connector *lconn = to_lsdc_connector(connector); + struct edid *edid_p = (struct edid *)lconn->edid_data; + int num = drm_add_edid_modes(connector, edid_p); + + if (num) + drm_connector_update_edid_property(connector, edid_p); + + drm_dbg_kms(ddev, "%d modes added\n", num); + + return num; +} + + +static int lsdc_get_modes_from_timings(struct drm_connector *connector) +{ + struct drm_device *ddev = connector->dev; + struct lsdc_connector *lconn = to_lsdc_connector(connector); + struct display_timings *disp_tim = lconn->disp_tim; + unsigned int i; + unsigned int num = 0; + + for (i = 0; i < disp_tim->num_timings; i++) { + const struct display_timing *dt = disp_tim->timings[i]; + struct drm_display_mode *mode; + struct videomode vm; + + videomode_from_timing(dt, &vm); + mode = drm_mode_create(ddev); + if (!mode) { + drm_err(ddev, "failed to add mode %ux%u\n", + dt->hactive.typ, dt->vactive.typ); + continue; + } + + drm_display_mode_from_videomode(&vm, mode); + + mode->type |= DRM_MODE_TYPE_DRIVER; + + if (i == disp_tim->native_mode) + mode->type |= DRM_MODE_TYPE_PREFERRED; + + drm_mode_probed_add(connector, mode); + num++; + } + + drm_dbg_kms(ddev, "%d modes added\n", num); + + return num; +} + + +static int lsdc_get_modes_from_ddc(struct drm_connector *connector, + struct i2c_adapter *ddc) +{ + struct edid *edid = NULL; + unsigned int num = 0; + + if (ddc) { + edid = drm_get_edid(connector, ddc); + if (edid) { + drm_connector_update_edid_property(connector, edid); + num = drm_add_edid_modes(connector, edid); + kfree(edid); + } else + goto fallback; + + return num; + } + +fallback: + + /* + * In case we cannot retrieve the EDIDs (broken or missing i2c + * bus), fallback on the XGA standards + */ + num = drm_add_modes_noedid(connector, 1920, 1200); + + /* And prefer a mode pretty much anyone can handle */ + drm_set_preferred_mode(connector, 1024, 768); + + return num; +} + + +static int lsdc_get_modes(struct drm_connector *connector) +{ + struct lsdc_connector *lconn = to_lsdc_connector(connector); + + if (lconn->has_edid) + return lsdc_get_modes_from_edid(connector); + + if (lconn->has_disp_tim) + return lsdc_get_modes_from_timings(connector); + + if (connector->connector_type == DRM_MODE_CONNECTOR_VIRTUAL) { + struct drm_device *ddev = connector->dev; + int count; + + count = drm_add_modes_noedid(connector, + ddev->mode_config.max_width, + ddev->mode_config.max_height); + + drm_set_preferred_mode(connector, 1024, 768); + + return count; + } + + return lsdc_get_modes_from_ddc(connector, lconn->ddc); +} + + +static enum drm_connector_status +lsdc_connector_detect(struct drm_connector *connector, bool force) +{ + struct lsdc_connector *lconn = to_lsdc_connector(connector); + + if (lconn->has_edid == true) + return connector_status_connected; + + if (lconn->has_disp_tim == true) + return connector_status_connected; + + if (lconn->ddc && drm_probe_ddc(lconn->ddc)) + return connector_status_connected; + + if ((connector->connector_type == DRM_MODE_CONNECTOR_DVIA) || + (connector->connector_type == DRM_MODE_CONNECTOR_DVID) || + (connector->connector_type == DRM_MODE_CONNECTOR_DVII)) + return connector_status_disconnected; + + if ((connector->connector_type == DRM_MODE_CONNECTOR_HDMIA) || + (connector->connector_type == DRM_MODE_CONNECTOR_HDMIB)) + return connector_status_disconnected; + + if (connector->connector_type == DRM_MODE_CONNECTOR_VIRTUAL) + return connector_status_connected; + + return connector_status_unknown; +} + + +/* + * @connector: point to the drm_connector structure + * + * Clean up connector resources + */ +static void lsdc_connector_destroy(struct drm_connector *connector) +{ + struct drm_device *ddev = connector->dev; + struct lsdc_connector *lconn = to_lsdc_connector(connector); + + if (lconn) { + if (lconn->ddc) + lsdc_destroy_i2c(connector->dev, lconn->ddc); + + drm_info(ddev, "destroying connector%u\n", lconn->index); + + devm_kfree(ddev->dev, lconn); + } + + drm_connector_cleanup(connector); +} + + +static const struct drm_connector_helper_funcs lsdc_connector_helpers = { + .get_modes = lsdc_get_modes, +}; + +/* + * These provide the minimum set of functions required to handle a connector + * + * Control connectors on a given device. + * + * Each CRTC may have one or more connectors attached to it. + * The functions below allow the core DRM code to control + * connectors, enumerate available modes, etc. + */ +static const struct drm_connector_funcs lsdc_connector_funcs = { + .dpms = drm_helper_connector_dpms, + .detect = lsdc_connector_detect, + .fill_modes = drm_helper_probe_single_connector_modes, + .destroy = lsdc_connector_destroy, + .reset = drm_atomic_helper_connector_reset, + .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, + .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, +}; + + +/* Get the simple EDID data from the device tree + * the length must be EDID_LENGTH, since it is simple. + * + * @np: device node contain edid data + * @edid_data: where the edid data to store to + */ +static bool lsdc_get_edid_from_dtb(struct device_node *np, + unsigned char *edid_data) +{ + int length; + const void *prop; + + if (np == NULL) + return false; + + prop = of_get_property(np, "edid", &length); + if (prop && (length == EDID_LENGTH)) { + memcpy(edid_data, prop, EDID_LENGTH); + return true; + } + + return false; +} + +/* Get display timings from the device tree + * + * @np: device node contain the display timings + * @pptim: where the pointer of struct display_timings to store to + */ +static void lsdc_get_display_timings_from_dtb(struct device_node *np, + struct display_timings **pptim) +{ + struct display_timings *timings; + + if (np == NULL) + return; + + timings = of_get_display_timings(np); + if (timings) + *pptim = timings; +} + + +static int lsdc_get_connector_type(struct drm_device *ddev, + struct device_node *output, + unsigned int index) +{ + const char *name; + int ret; + + ret = of_property_read_string(output, "connector", &name); + if (ret < 0) { + drm_warn(ddev, "please give a valid connector property\n"); + return DRM_MODE_CONNECTOR_Unknown; + } + + if (strncmp(name, "vga-connector", 13) == 0) { + ret = DRM_MODE_CONNECTOR_VGA; + drm_info(ddev, "connector%d is VGA\n", index); + } else if (strncmp(name, "dvi-connector", 13) == 0) { + bool analog, digital; + + analog = of_property_read_bool(output, "analog"); + digital = of_property_read_bool(output, "digital"); + + if (analog && !digital) + ret = DRM_MODE_CONNECTOR_DVIA; + else if (analog && digital) + ret = DRM_MODE_CONNECTOR_DVII; + else + ret = DRM_MODE_CONNECTOR_DVID; + + drm_info(ddev, "connector%d is DVI\n", index); + } else if (strncmp(name, "virtual-connector", 17) == 0) { + ret = DRM_MODE_CONNECTOR_VIRTUAL; + drm_info(ddev, "connector%d is virtual\n", index); + } else if (strncmp(name, "dpi-connector", 13) == 0) { + ret = DRM_MODE_CONNECTOR_DPI; + drm_info(ddev, "connector%d is DPI\n", index); + } else if (strncmp(name, "hdmi-connector", 14) == 0) { + int res; + const char *hdmi_type; + + res = of_property_read_string(output, "type", &hdmi_type); + if (res == 0) { + if (!strcmp(hdmi_type, "b")) + ret = DRM_MODE_CONNECTOR_HDMIB; + else + ret = DRM_MODE_CONNECTOR_HDMIA; + } else + ret = DRM_MODE_CONNECTOR_HDMIA; + + drm_info(ddev, "connector%d is HDMI, type is %s\n", + index, hdmi_type); + } else { + ret = DRM_MODE_CONNECTOR_Unknown; + drm_info(ddev, "The type of connector%d unknown\n", index); + } + + return ret; +} + + +struct lsdc_connector *lsdc_connector_init(struct lsdc_device *ldev, + unsigned int index) +{ + struct drm_device *ddev = &ldev->drm; + struct device_node *np = ddev->dev->of_node; + struct device_node *output = NULL; + struct lsdc_connector *lconn; + struct drm_connector *connector; + bool available = false; + unsigned int connector_type; + int ret; + + lconn = devm_kzalloc(ddev->dev, sizeof(*lconn), GFP_KERNEL); + if (lconn == NULL) + return ERR_PTR(-ENOMEM); + + lconn->index = index; + + output = of_parse_phandle(np, "output-ports", index); + if (output) { + struct device_node *disp_tims_np; + + available = of_device_is_available(output); + + if (available == false) { + drm_info(ddev, "connector%d is not available\n", index); + of_node_put(output); + return NULL; + } + + lconn->has_edid = of_property_read_bool(output, "edid"); + disp_tims_np = of_get_child_by_name(output, "display-timings"); + if (disp_tims_np) { + of_node_put(disp_tims_np); + lconn->has_disp_tim = true; + } else + lconn->has_disp_tim = false; + } else + drm_warn(ddev, "no output-ports property, please update dtb\n"); + + /* + * Providing a blindly support even through there is + * no output-ports property in the dtb. + */ + if (lconn->has_edid) { + lsdc_get_edid_from_dtb(output, lconn->edid_data); + drm_info(ddev, "connector%d provide edid\n", index); + } + + if (lconn->has_disp_tim) { + lsdc_get_display_timings_from_dtb(output, &lconn->disp_tim); + drm_info(ddev, "connector%d provide display timings\n", index); + } + + connector_type = lsdc_get_connector_type(ddev, output, index); + + if (output) + of_node_put(output); + + connector = &lconn->base; + + /* bypass the ddc creation if the edid or display timing is provided */ + if ((lconn->has_edid == false) && + (lconn->has_disp_tim == false) && + (connector_type != DRM_MODE_CONNECTOR_VIRTUAL)) { + const struct lsdc_chip_desc * const dc = ldev->desc; + + if (dc->have_builtin_i2c) + lconn->ddc = lsdc_create_i2c_chan(ddev, index); + else + lconn->ddc = lsdc_get_i2c_adapter(ddev, index); + + if (lconn->ddc && (IS_ERR(lconn->ddc) == false)) { + drm_info(ddev, "i2c%d for connector%d created\n", + i2c_adapter_id(lconn->ddc), index); + + /* only pull if the connector have a ddc */ + connector->polled = DRM_CONNECTOR_POLL_CONNECT | + DRM_CONNECTOR_POLL_DISCONNECT; + } + } + + ret = drm_connector_init_with_ddc(ddev, + connector, + &lsdc_connector_funcs, + connector_type, + lconn->ddc); + if (ret) { + drm_err(ddev, "init connector%d failed\n", index); + goto err_i2c_destroy; + } + + drm_connector_helper_add(connector, &lsdc_connector_helpers); + + return lconn; + +err_i2c_destroy: + lsdc_destroy_i2c(ddev, lconn->ddc); + return NULL; +} diff --git a/drivers/gpu/drm/lsdc/lsdc_connector.h b/drivers/gpu/drm/lsdc/lsdc_connector.h new file mode 100644 index 000000000000..e9f94a969f74 --- /dev/null +++ b/drivers/gpu/drm/lsdc/lsdc_connector.h @@ -0,0 +1,60 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2020 Loongson Corporation + * + * Permission is hereby granted, free of charge, to any person obtaining a + * copy of this software and associated documentation files (the + * "Software"), to deal in the Software without restriction, including + * without limitation the rights to use, copy, modify, merge, publish, + * distribute, sub license, and/or sell copies of the Software, and to + * permit persons to whom the Software is furnished to do so, subject to + * the following conditions: + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IN NO EVENT SHALL + * THE COPYRIGHT HOLDERS, AUTHORS AND/OR ITS SUPPLIERS BE LIABLE FOR ANY CLAIM, + * DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR + * OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE + * USE OR OTHER DEALINGS IN THE SOFTWARE. + * + * The above copyright notice and this permission notice (including the + * next paragraph) shall be included in all copies or substantial portions + * of the Software. + */ + +/* + * Authors: + * Sui Jingfeng suijingfeng@loongson.cn + */ + + +#ifndef __LSDC_CONNECTOR_H__ +#define __LSDC_CONNECTOR_H__ + +#include <drm/drm_device.h> +#include <drm/drm_connector.h> + +struct lsdc_connector { + struct drm_connector base; + + struct i2c_adapter *ddc; + + /* pass EDID from dtb support */ + unsigned char edid_data[EDID_LENGTH]; + bool has_edid; + + /* pass display timmings from dtb support */ + struct display_timings *disp_tim; + bool has_disp_tim; + + int index; +}; + +#define to_lsdc_connector(x) \ + container_of(x, struct lsdc_connector, base) + +struct lsdc_connector *lsdc_connector_init(struct lsdc_device *ldev, + unsigned int index); + +#endif diff --git a/drivers/gpu/drm/lsdc/lsdc_crtc.c b/drivers/gpu/drm/lsdc/lsdc_crtc.c new file mode 100644 index 000000000000..7531389f4896 --- /dev/null +++ b/drivers/gpu/drm/lsdc/lsdc_crtc.c @@ -0,0 +1,440 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2020 Loongson Corporation + * + * Permission is hereby granted, free of charge, to any person obtaining a + * copy of this software and associated documentation files (the + * "Software"), to deal in the Software without restriction, including + * without limitation the rights to use, copy, modify, merge, publish, + * distribute, sub license, and/or sell copies of the Software, and to + * permit persons to whom the Software is furnished to do so, subject to + * the following conditions: + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IN NO EVENT SHALL + * THE COPYRIGHT HOLDERS, AUTHORS AND/OR ITS SUPPLIERS BE LIABLE FOR ANY CLAIM, + * DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR + * OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE + * USE OR OTHER DEALINGS IN THE SOFTWARE. + * + * The above copyright notice and this permission notice (including the + * next paragraph) shall be included in all copies or substantial portions + * of the Software. + */ + +/* + * Authors: + * Sui Jingfeng suijingfeng@loongson.cn + */ + +#include <drm/drm_print.h> +#include <drm/drm_device.h> +#include <drm/drm_crtc.h> +#include <drm/drm_plane.h> +#include <drm/drm_atomic.h> +#include <drm/drm_vblank.h> +#include <drm/drm_drv.h> + + +#include <drm/drm_fb_cma_helper.h> +#include <drm/drm_gem_cma_helper.h> +#include <drm/drm_atomic_helper.h> +#include <drm/drm_gem_framebuffer_helper.h> +#include <drm/drm_gem_atomic_helper.h> +#include <drm/drm_damage_helper.h> + +#include "lsdc_drv.h" +#include "lsdc_regs.h" +#include "lsdc_pll.h" + + +static int lsdc_crtc_enable_vblank(struct drm_crtc *crtc) +{ + struct lsdc_device *ldev = to_lsdc(crtc->dev); + unsigned int index = drm_crtc_index(crtc); + struct drm_crtc_state *state = crtc->state; + u32 val; + + if (state->enable) { + val = lsdc_reg_read32(ldev, LSDC_INT_REG); + + if (index == 0) + val |= INT_CRTC0_VS_EN; + else if (index == 1) + val |= INT_CRTC1_VS_EN; + + lsdc_reg_write32(ldev, LSDC_INT_REG, val); + } + + return 0; +} + + +static void lsdc_crtc_disable_vblank(struct drm_crtc *crtc) +{ + struct lsdc_device *ldev = to_lsdc(crtc->dev); + unsigned int index = drm_crtc_index(crtc); + u32 val; + + val = lsdc_reg_read32(ldev, LSDC_INT_REG); + + if (index == 0) + val &= ~INT_CRTC0_VS_EN; + else if (index == 1) + val &= ~INT_CRTC1_VS_EN; + + lsdc_reg_write32(ldev, LSDC_INT_REG, val); +} + + +static void lsdc_crtc_reset(struct drm_crtc *crtc) +{ + struct drm_device *ddev = crtc->dev; + struct lsdc_device *ldev = to_lsdc(ddev); + unsigned int index = drm_crtc_index(crtc); + struct lsdc_crtc_state *priv_crtc_state; + u32 val; + + /* The crtc get soft reset if bit 20 of CRTC*_CFG_REG + * is write with falling edge. + * + * Doing this to switch from soft reset state to working state + */ + if (index == 0) { + val = CFG_RESET_BIT | CFG_OUTPUT_EN_BIT | LSDC_PF_XRGB8888; + lsdc_reg_write32(ldev, LSDC_CRTC0_CFG_REG, val); + } else if (index == 1) { + val = CFG_RESET_BIT | CFG_OUTPUT_EN_BIT | LSDC_PF_XRGB8888; + lsdc_reg_write32(ldev, LSDC_CRTC1_CFG_REG, val); + } + + + if (crtc->state) { + priv_crtc_state = to_lsdc_crtc_state(crtc->state); + __drm_atomic_helper_crtc_destroy_state(&priv_crtc_state->base); + kfree(priv_crtc_state); + } + + priv_crtc_state = kzalloc(sizeof(*priv_crtc_state), GFP_KERNEL); + if (!priv_crtc_state) + return; + + priv_crtc_state->pix_fmt = val & CFG_PIX_FMT_MASK; + + __drm_atomic_helper_crtc_reset(crtc, &priv_crtc_state->base); + + drm_info(ddev, "crtc%u reset\n", index); +} + + +static void lsdc_crtc_atomic_destroy_state(struct drm_crtc *crtc, + struct drm_crtc_state *state) +{ + struct lsdc_crtc_state *priv_crtc_state = to_lsdc_crtc_state(state); + + __drm_atomic_helper_crtc_destroy_state(&priv_crtc_state->base); + + kfree(priv_crtc_state); +} + + +static struct drm_crtc_state *lsdc_crtc_atomic_duplicate_state(struct drm_crtc *crtc) +{ + struct lsdc_crtc_state *new_priv_state; + struct lsdc_crtc_state *old_priv_state; + struct drm_device *ddev = crtc->dev; + + if (drm_WARN_ON(ddev, !crtc->state)) + return NULL; + + new_priv_state = kmalloc(sizeof(*new_priv_state), GFP_KERNEL); + if (!new_priv_state) + return NULL; + + __drm_atomic_helper_crtc_duplicate_state(crtc, &new_priv_state->base); + + old_priv_state = to_lsdc_crtc_state(crtc->state); + + memcpy(&new_priv_state->pparams, &old_priv_state->pparams, + sizeof(new_priv_state->pparams)); + + new_priv_state->pix_fmt = old_priv_state->pix_fmt; + + return &new_priv_state->base; +} + + +static const struct drm_crtc_funcs lsdc_crtc_funcs = { + .reset = lsdc_crtc_reset, + .destroy = drm_crtc_cleanup, + .set_config = drm_atomic_helper_set_config, + .page_flip = drm_atomic_helper_page_flip, + .atomic_duplicate_state = lsdc_crtc_atomic_duplicate_state, + .atomic_destroy_state = lsdc_crtc_atomic_destroy_state, + .enable_vblank = lsdc_crtc_enable_vblank, + .disable_vblank = lsdc_crtc_disable_vblank, +}; + + +static enum drm_mode_status +lsdc_crtc_helper_mode_valid(struct drm_crtc *crtc, + const struct drm_display_mode *mode) +{ + struct drm_device *ddev = crtc->dev; + struct lsdc_device *ldev = to_lsdc(ddev); + const struct lsdc_chip_desc *desc = ldev->desc; + + if (mode->hdisplay > desc->max_width) + return MODE_BAD_HVALUE; + if (mode->vdisplay > desc->max_height) + return MODE_BAD_VVALUE; + + if (mode->clock > desc->max_pixel_clk) { + drm_dbg_kms(ddev, "mode %dx%d, pixel clock=%d is too high\n", + mode->hdisplay, mode->vdisplay, mode->clock); + return MODE_CLOCK_HIGH; + } + + /* the crtc hardware dma take 256 bytes once a time + * TODO: check RGB565 support + */ + if ((mode->hdisplay * 4) % desc->stride_alignment) { + drm_dbg_kms(ddev, "stride is not %u bytes aligned\n", + desc->stride_alignment); + return MODE_BAD; + } + + return MODE_OK; +} + + +static void lsdc_update_pixclk(struct drm_crtc *crtc, unsigned int pixclk, bool verbose) +{ + struct lsdc_display_pipe *dispipe; + struct lsdc_pll *pixpll; + const struct lsdc_pixpll_funcs *clkfun; + struct lsdc_crtc_state *priv_crtc_state; + + priv_crtc_state = to_lsdc_crtc_state(crtc->state); + + dispipe = container_of(crtc, struct lsdc_display_pipe, crtc); + pixpll = &dispipe->pixpll; + clkfun = pixpll->funcs; + + /* config the pixel pll */ + clkfun->update(pixpll, &priv_crtc_state->pparams); + + if (verbose) + clkfun->print(pixpll, pixclk); +} + + +static void lsdc_crtc_helper_mode_set_nofb(struct drm_crtc *crtc) +{ + struct drm_device *ddev = crtc->dev; + struct lsdc_device *ldev = to_lsdc(ddev); + struct drm_display_mode *mode = &crtc->state->adjusted_mode; + unsigned int hr = mode->hdisplay; + unsigned int hss = mode->hsync_start; + unsigned int hse = mode->hsync_end; + unsigned int hfl = mode->htotal; + unsigned int vr = mode->vdisplay; + unsigned int vss = mode->vsync_start; + unsigned int vse = mode->vsync_end; + unsigned int vfl = mode->vtotal; + unsigned int pixclock = mode->clock; + unsigned int index = drm_crtc_index(crtc); + + + if (index == 0) { + /* CRTC 0 */ + u32 hsync, vsync; + + lsdc_reg_write32(ldev, LSDC_CRTC0_FB_ORIGIN_REG, 0); + + /* 26:16 total pixels, 10:0 visiable pixels, in horizontal */ + lsdc_reg_write32(ldev, LSDC_CRTC0_HDISPLAY_REG, + (mode->crtc_htotal << 16) | mode->crtc_hdisplay); + + /* 26:16 total pixels, 10:0 visiable pixels, in vertical */ + lsdc_reg_write32(ldev, LSDC_CRTC0_VDISPLAY_REG, + (mode->crtc_vtotal << 16) | mode->crtc_vdisplay); + + /* 26:16 hsync end, 10:0 hsync start */ + hsync = (mode->crtc_hsync_end << 16) | mode->crtc_hsync_start; + + if (mode->flags & DRM_MODE_FLAG_NHSYNC) + hsync |= INV_HSYNC_BIT; + + lsdc_reg_write32(ldev, LSDC_CRTC0_HSYNC_REG, EN_HSYNC_BIT | hsync); + + /* 26:16 vsync end, 10:0 vsync start */ + vsync = (mode->crtc_vsync_end << 16) | mode->crtc_vsync_start; + + if (mode->flags & DRM_MODE_FLAG_NVSYNC) + vsync |= INV_VSYNC_BIT; + + lsdc_reg_write32(ldev, LSDC_CRTC0_VSYNC_REG, EN_VSYNC_BIT | vsync); + + } else if (index == 1) { + /* CRTC 1 */ + u32 hsync, vsync; + + lsdc_reg_write32(ldev, LSDC_CRTC1_FB_ORIGIN_REG, 0); + + /* 26:16 total pixels, 10:0 visiable pixels, in horizontal */ + lsdc_reg_write32(ldev, LSDC_CRTC1_HDISPLAY_REG, + (mode->crtc_htotal << 16) | mode->crtc_hdisplay); + + /* 26:16 total pixels, 10:0 visiable pixels, in vertical */ + lsdc_reg_write32(ldev, LSDC_CRTC1_VDISPLAY_REG, + (mode->crtc_vtotal << 16) | mode->crtc_vdisplay); + + /* 26:16 hsync end, 10:0 hsync start */ + hsync = (mode->crtc_hsync_end << 16) | mode->crtc_hsync_start; + + if (mode->flags & DRM_MODE_FLAG_NHSYNC) + hsync |= INV_HSYNC_BIT; + + lsdc_reg_write32(ldev, LSDC_CRTC1_HSYNC_REG, EN_HSYNC_BIT | hsync); + + /* 26:16 vsync end, 10:0 vsync start */ + vsync = (mode->crtc_vsync_end << 16) | mode->crtc_vsync_start; + + if (mode->flags & DRM_MODE_FLAG_NVSYNC) + vsync |= INV_VSYNC_BIT; + + lsdc_reg_write32(ldev, LSDC_CRTC1_VSYNC_REG, EN_VSYNC_BIT | vsync); + } + + drm_dbg_kms(ddev, "hdisplay=%d, hsync_start=%d, hsync_end=%d, htotal=%d\n", + hr, hss, hse, hfl); + + drm_dbg_kms(ddev, "vdisplay=%d, vsync_start=%d, vsync_end=%d, vtotal=%d\n", + vr, vss, vse, vfl); + + drm_dbg_kms(ddev, "%s modeset: %ux%u\n", crtc->name, hr, vr); + + lsdc_update_pixclk(crtc, pixclock, ldev->verbose); +} + + +static void lsdc_enable_display(struct lsdc_device *ldev, unsigned int index) +{ + u32 val; + + if (index == 0) { + val = lsdc_reg_read32(ldev, LSDC_CRTC0_CFG_REG); + val |= CFG_OUTPUT_EN_BIT; + lsdc_reg_write32(ldev, LSDC_CRTC0_CFG_REG, val); + } else if (index == 1) { + val = lsdc_reg_read32(ldev, LSDC_CRTC1_CFG_REG); + val |= CFG_OUTPUT_EN_BIT; + lsdc_reg_write32(ldev, LSDC_CRTC1_CFG_REG, val); + } +} + + +static void lsdc_disable_display(struct lsdc_device *ldev, unsigned int index) +{ + u32 val; + + if (index == 0) { + val = lsdc_reg_read32(ldev, LSDC_CRTC0_CFG_REG); + val &= ~CFG_OUTPUT_EN_BIT; + lsdc_reg_write32(ldev, LSDC_CRTC0_CFG_REG, val); + } else if (index == 1) { + val = lsdc_reg_read32(ldev, LSDC_CRTC1_CFG_REG); + val &= ~CFG_OUTPUT_EN_BIT; + lsdc_reg_write32(ldev, LSDC_CRTC1_CFG_REG, val); + } +} + + +static void lsdc_crtc_helper_atomic_enable(struct drm_crtc *crtc, + struct drm_atomic_state *state) +{ + struct drm_device *ddev = crtc->dev; + struct lsdc_device *ldev = to_lsdc(ddev); + + drm_crtc_vblank_on(crtc); + + lsdc_enable_display(ldev, drm_crtc_index(crtc)); + + drm_dbg_kms(ddev, "%s: enabled\n", crtc->name); +} + + +static void lsdc_crtc_helper_atomic_disable(struct drm_crtc *crtc, + struct drm_atomic_state *state) +{ + struct drm_device *ddev = crtc->dev; + struct lsdc_device *ldev = to_lsdc(ddev); + + drm_crtc_vblank_off(crtc); + + lsdc_disable_display(ldev, drm_crtc_index(crtc)); + + drm_dbg_kms(ddev, "%s: disabled\n", crtc->name); +} + + +static void lsdc_crtc_atomic_flush(struct drm_crtc *crtc, + struct drm_atomic_state *state) +{ + struct drm_pending_vblank_event *event = crtc->state->event; + + if (event) { + crtc->state->event = NULL; + + spin_lock_irq(&crtc->dev->event_lock); + if (drm_crtc_vblank_get(crtc) == 0) + drm_crtc_arm_vblank_event(crtc, event); + else + drm_crtc_send_vblank_event(crtc, event); + spin_unlock_irq(&crtc->dev->event_lock); + } +} + + +static const struct drm_crtc_helper_funcs lsdc_crtc_helper_funcs = { + .mode_valid = lsdc_crtc_helper_mode_valid, + .mode_set_nofb = lsdc_crtc_helper_mode_set_nofb, + .atomic_enable = lsdc_crtc_helper_atomic_enable, + .atomic_disable = lsdc_crtc_helper_atomic_disable, + .atomic_flush = lsdc_crtc_atomic_flush, +}; + + + +/** + * lsdc_crtc_init + * + * @ddev: point to the drm_device structure + * @index: hardware crtc index + * + * Init CRTC + */ +int lsdc_crtc_init(struct drm_device *ddev, + struct drm_crtc *crtc, + unsigned int index, + struct drm_plane *primary, + struct drm_plane *cursor) +{ + int ret; + + drm_crtc_helper_add(crtc, &lsdc_crtc_helper_funcs); + + ret = drm_mode_crtc_set_gamma_size(crtc, 256); + if (ret) + drm_warn(ddev, "set the gamma table size failed\n"); + + return drm_crtc_init_with_planes(ddev, + crtc, + primary, + cursor, + &lsdc_crtc_funcs, + "crtc%d", + index); +} diff --git a/drivers/gpu/drm/lsdc/lsdc_drv.c b/drivers/gpu/drm/lsdc/lsdc_drv.c new file mode 100644 index 000000000000..39844ecbf122 --- /dev/null +++ b/drivers/gpu/drm/lsdc/lsdc_drv.c @@ -0,0 +1,845 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2020 Loongson Corporation + * + * Permission is hereby granted, free of charge, to any person obtaining a + * copy of this software and associated documentation files (the + * "Software"), to deal in the Software without restriction, including + * without limitation the rights to use, copy, modify, merge, publish, + * distribute, sub license, and/or sell copies of the Software, and to + * permit persons to whom the Software is furnished to do so, subject to + * the following conditions: + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IN NO EVENT SHALL + * THE COPYRIGHT HOLDERS, AUTHORS AND/OR ITS SUPPLIERS BE LIABLE FOR ANY CLAIM, + * DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR + * OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE + * USE OR OTHER DEALINGS IN THE SOFTWARE. + * + * The above copyright notice and this permission notice (including the + * next paragraph) shall be included in all copies or substantial portions + * of the Software. + */ + +/* + * Authors: + * Sui Jingfeng suijingfeng@loongson.cn + */ + +#include <linux/errno.h> +#include <linux/string.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/of_reserved_mem.h> + +#include <drm/drm_drv.h> +#include <drm/drm_aperture.h> +#include <drm/drm_of.h> +#include <drm/drm_plane.h> +#include <drm/drm_vblank.h> +#include <drm/drm_debugfs.h> +#include <drm/drm_fb_helper.h> +#include <drm/drm_crtc_helper.h> +#include <drm/drm_gem_cma_helper.h> +#include <drm/drm_fb_cma_helper.h> +#include <drm/drm_gem_framebuffer_helper.h> +#include <drm/drm_atomic_helper.h> +#include <drm/drm_damage_helper.h> +#include <drm/drm_probe_helper.h> + +#include "lsdc_drv.h" +#include "lsdc_irq.h" +#include "lsdc_regs.h" +#include "lsdc_connector.h" +#include "lsdc_pll.h" + + +#define DRIVER_AUTHOR "Sui Jingfeng suijingfeng@loongson.cn" +#define DRIVER_NAME "lsdc" +#define DRIVER_DESC "drm driver for loongson's display controller" +#define DRIVER_DATE "20200701" +#define DRIVER_MAJOR 1 +#define DRIVER_MINOR 0 +#define DRIVER_PATCHLEVEL 0 + +static int lsdc_modeset = 1; +MODULE_PARM_DESC(modeset, "Enable/disable CMA-based KMS(1 = enabled(default), 0 = disabled)"); +module_param_named(modeset, lsdc_modeset, int, 0644); + +static int lsdc_cached_coherent = 1; +MODULE_PARM_DESC(cached_coherent, "uss cached coherent mapping(1 = enabled(default), 0 = disabled)"); +module_param_named(cached_coherent, lsdc_cached_coherent, int, 0644); + +static int lsdc_dirty_update = -1; +MODULE_PARM_DESC(dirty_update, "enable dirty update(1 = enabled, 0 = disabled(default))"); +module_param_named(dirty_update, lsdc_dirty_update, int, 0644); + +static int lsdc_use_vram_helper = -1; +MODULE_PARM_DESC(use_vram_helper, "use vram helper based solution(1 = enabled, 0 = disabled(default))"); +module_param_named(use_vram_helper, lsdc_use_vram_helper, int, 0644); + +static int lsdc_verbose = -1; +MODULE_PARM_DESC(verbose, "Enable/disable print some key information"); +module_param_named(verbose, lsdc_verbose, int, 0644); + + +static const struct lsdc_chip_desc dc_in_ls2k1000 = { + .chip = LSDC_CHIP_2K1000, + .num_of_crtc = LSDC_MAX_CRTC, + /* ls2k1000 user manual say the max pixel clock can be about 200MHz */ + .max_pixel_clk = 200000, + .max_width = 2560, + .max_height = 2048, + .num_of_hw_cursor = 1, + .hw_cursor_w = 32, + .hw_cursor_h = 32, + .have_builtin_i2c = false, + .stride_alignment = 256, +}; + +static const struct lsdc_chip_desc dc_in_ls2k0500 = { + .chip = LSDC_CHIP_2K0500, + .num_of_crtc = LSDC_MAX_CRTC, + .max_pixel_clk = 200000, + .max_width = 2048, + .max_height = 2048, + .num_of_hw_cursor = 1, + .hw_cursor_w = 32, + .hw_cursor_h = 32, + .have_builtin_i2c = false, + .stride_alignment = 256, +}; + +static const struct lsdc_chip_desc dc_in_ls7a1000 = { + .chip = LSDC_CHIP_7A1000, + .num_of_crtc = LSDC_MAX_CRTC, + .max_pixel_clk = 200000, + .max_width = 2048, + .max_height = 2048, + .num_of_hw_cursor = 1, + .hw_cursor_w = 32, + .hw_cursor_h = 32, + .have_builtin_i2c = true, + .stride_alignment = 256, +}; + +/* + * We need the device tree provided additional information to tell the DC + * in different chip apart. + */ +static const struct of_device_id lsdc_drm_of_match[] = { + { .compatible = "loongson,loongson64c-4core-ls7a", .data = &dc_in_ls7a1000 }, + { .compatible = "loongson,loongson64g-4core-ls7a", .data = &dc_in_ls7a1000 }, + { .compatible = "loongson,loongson64-2core-2k1000", .data = &dc_in_ls2k1000 }, + { .compatible = "loongson,loongson2k1000", .data = &dc_in_ls2k1000 }, + { .compatible = "loongson,ls2k1000", .data = &dc_in_ls2k1000 }, + { .compatible = "loongson,display-subsystem", .data = &dc_in_ls2k1000 }, + { .compatible = "loongson,ls-fb", .data = &dc_in_ls2k1000 }, + { .compatible = "loongson,loongson2k0500", .data = &dc_in_ls2k0500 }, + { /* sentinel */ }, +}; + + +static struct drm_framebuffer * +lsdc_drm_gem_fb_create(struct drm_device *ddev, struct drm_file *file, + const struct drm_mode_fb_cmd2 *mode_cmd) +{ + struct lsdc_device *ldev = to_lsdc(ddev); + + if (ldev->dirty_update) + return drm_gem_fb_create_with_dirty(ddev, file, mode_cmd); + + return drm_gem_fb_create(ddev, file, mode_cmd); +} + + +static enum drm_mode_status lsdc_device_mode_valid(struct drm_device *ddev, + const struct drm_display_mode *mode) +{ +#ifdef CONFIG_DRM_LSDC_VRAM_DRIVER + struct lsdc_device *ldev = to_lsdc(ddev); + + if (ldev->use_vram_helper == true) + return drm_vram_helper_mode_valid(ddev, mode); +#endif + + return MODE_OK; +} + + +static const struct drm_mode_config_funcs lsdc_mode_config_funcs = { + .fb_create = lsdc_drm_gem_fb_create, + .output_poll_changed = drm_fb_helper_output_poll_changed, + .atomic_check = drm_atomic_helper_check, + .atomic_commit = drm_atomic_helper_commit, + .mode_valid = lsdc_device_mode_valid, +}; + + +#ifdef CONFIG_DEBUG_FS +static int lsdc_show_pxlclock(struct seq_file *m, void *arg) +{ + struct drm_info_node *node = (struct drm_info_node *)m->private; + struct drm_device *ddev = node->minor->dev; + struct lsdc_device *ldev = to_lsdc(ddev); + struct drm_crtc *crtc; + + drm_for_each_crtc(crtc, ddev) { + struct drm_crtc_state *state = crtc->state; + int index = drm_crtc_index(crtc); + struct lsdc_display_pipe *pipe = &ldev->disp_pipe[index]; + struct lsdc_pll *pixpll = &pipe->pixpll; + const struct lsdc_pixpll_funcs *clkfun = pixpll->funcs; + unsigned int clkrate = clkfun->get_clock_rate(pixpll); + unsigned int mode_clock = crtc->mode.crtc_clock; + + seq_printf(m, "\n"); + seq_printf(m, "CRTC%u, %s, %s\n", index, + state->active ? "active" : "non-active", + state->enable ? "enabled" : "disabled"); + seq_printf(m, "hw clock: %u kHz\n", clkrate); + seq_printf(m, "mode: %u kHz\n", mode_clock); + + seq_printf(m, "div_out=%u, loopc=%u, div_ref=%u\n", + pixpll->core_params.div_out, + pixpll->core_params.loopc, + pixpll->core_params.div_ref); + } + + return 0; +} + + +static int lsdc_mm_show(struct seq_file *m, void *arg) +{ + struct drm_info_node *node = (struct drm_info_node *) m->private; + struct drm_device *ddev = node->minor->dev; + struct drm_printer p = drm_seq_file_printer(m); + + drm_mm_print(&ddev->vma_offset_manager->vm_addr_space_mm, &p); + return 0; +} + +static struct drm_info_list lsdc_debugfs_list[] = { + { "clocks", lsdc_show_pxlclock, 0 }, + { "mm", lsdc_mm_show, 0, NULL }, +}; + +static void lsdc_debugfs_init(struct drm_minor *minor) +{ + drm_debugfs_create_files(lsdc_debugfs_list, + ARRAY_SIZE(lsdc_debugfs_list), + minor->debugfs_root, + minor); +} +#endif + + +static struct drm_gem_object * +lsdc_drm_gem_create_object(struct drm_device *ddev, size_t size) +{ + struct lsdc_device *ldev = to_lsdc(ddev); + struct drm_gem_cma_object *obj = kzalloc(sizeof(*obj), GFP_KERNEL); + + if (!obj) + return ERR_PTR(-ENOMEM); + + if (ldev->cached_coherent) + obj->map_noncoherent = true; + + return &obj->base; +} + + +static int lsdc_gem_cma_dumb_create(struct drm_file *file, + struct drm_device *ddev, + struct drm_mode_create_dumb *args) +{ + struct lsdc_device *ldev = to_lsdc(ddev); + const struct lsdc_chip_desc *desc = ldev->desc; + unsigned int bytes_per_pixel = (args->bpp + 7) / 8; + unsigned int pitch = bytes_per_pixel * args->width; + + /* + * The dc in ls7a1000/ls2k1000/ls2k0500 require the stride be a + * multiple of 256 bytes, which is for sake of optimize dma data + * transfer. + */ + args->pitch = roundup(pitch, desc->stride_alignment); + + return drm_gem_cma_dumb_create_internal(file, ddev, args); +} + + +DEFINE_DRM_GEM_CMA_FOPS(lsdc_drv_fops); + + +static const struct drm_driver lsdc_drm_driver_cma_stub = { + .driver_features = DRIVER_GEM | DRIVER_MODESET | DRIVER_ATOMIC, + + .lastclose = drm_fb_helper_lastclose, + .fops = &lsdc_drv_fops, + .gem_create_object = lsdc_drm_gem_create_object, + + .name = DRIVER_NAME, + .desc = DRIVER_DESC, + .date = DRIVER_DATE, + .major = DRIVER_MAJOR, + .minor = DRIVER_MINOR, + .patchlevel = DRIVER_PATCHLEVEL, + + DRM_GEM_CMA_DRIVER_OPS_WITH_DUMB_CREATE(lsdc_gem_cma_dumb_create), + +#ifdef CONFIG_DEBUG_FS + .debugfs_init = lsdc_debugfs_init, +#endif +}; + + +DEFINE_DRM_GEM_FOPS(lsdc_fops); + + +#ifdef CONFIG_DRM_LSDC_VRAM_DRIVER +static const struct drm_driver lsdc_vram_driver_stub = { + .driver_features = DRIVER_MODESET | DRIVER_GEM | DRIVER_ATOMIC, + .fops = &lsdc_fops, + + .name = DRIVER_NAME, + .desc = DRIVER_DESC, + .date = DRIVER_DATE, + .major = DRIVER_MAJOR, + .minor = DRIVER_MINOR, + .patchlevel = DRIVER_PATCHLEVEL, + + DRM_GEM_VRAM_DRIVER, +}; +#endif + + +static int lsdc_modeset_init(struct lsdc_device *ldev, const uint32_t num_crtc) +{ + struct drm_device *ddev = &ldev->drm; + struct lsdc_display_pipe *dispipe; + struct lsdc_connector *lconn; + unsigned int i; + int ret; + + /* first find all of connector available */ + for (i = 0; i < num_crtc; i++) { + lconn = lsdc_connector_init(ldev, i); + dispipe = &ldev->disp_pipe[i]; + + if (IS_ERR(lconn)) + return PTR_ERR(lconn); + else if (lconn == NULL) { + dispipe->lconn = NULL; + dispipe->available = false; + continue; + } + + /* take a record */ + dispipe->available = true; + dispipe->lconn = lconn; + ldev->num_output++; + } + + drm_info(ddev, "number of outputs: %u\n", ldev->num_output); + + for (i = 0; i < num_crtc; i++) { + struct lsdc_display_pipe * const dispipe = &ldev->disp_pipe[i]; + struct drm_plane * const primary = &dispipe->primary; + struct drm_plane * const cursor = &dispipe->cursor; + struct drm_encoder * const encoder = &dispipe->encoder; + struct drm_crtc * const crtc = &dispipe->crtc; + struct lsdc_pll * const pixpll = &dispipe->pixpll; + + dispipe->index = i; + + ret = lsdc_pixpll_init(pixpll, ddev, i); + if (ret) + return ret; + + ret = lsdc_plane_init(ldev, primary, DRM_PLANE_TYPE_PRIMARY, i); + if (ret) + return ret; + + ret = lsdc_plane_init(ldev, cursor, DRM_PLANE_TYPE_CURSOR, i); + if (ret) + return ret; + + /* + * Initial all of the CRTC available, in this way the crtc + * index is equal to the hardware crtc index. That is: + * display pipe 0 = crtc0 + dvo0 + encoder0 + * display pipe 1 = crtc1 + dvo1 + encoder1 + */ + ret = lsdc_crtc_init(ddev, crtc, i, primary, cursor); + if (ret) + return ret; + + if (dispipe->available) { + ret = lsdc_encoder_init(encoder, + &dispipe->lconn->base, + ddev, + i, + ldev->num_output); + if (ret) + return ret; + } + + drm_info(ddev, "display pipe %u initialized\n", i); + } + + return 0; +} + + +static int lsdc_mode_config_init(struct lsdc_device *ldev) +{ + const struct lsdc_chip_desc * const descp = ldev->desc; + struct drm_device *ddev = &ldev->drm; + int ret; + + spin_lock_init(&ldev->reglock); + + drm_mode_config_init(ddev); + + ddev->mode_config.funcs = &lsdc_mode_config_funcs; + ddev->mode_config.min_width = 1; + ddev->mode_config.min_height = 1; + ddev->mode_config.preferred_depth = 24; + ddev->mode_config.prefer_shadow = 0; + + ddev->mode_config.max_width = 4096; + ddev->mode_config.max_height = 4096; + + ddev->mode_config.cursor_width = descp->hw_cursor_h; + ddev->mode_config.cursor_height = descp->hw_cursor_h; + + if (ldev->vram_base) + ddev->mode_config.fb_base = ldev->vram_base; + + ret = lsdc_modeset_init(ldev, descp->num_of_crtc); + if (ret) + goto out_mode_config; + + drm_mode_config_reset(ddev); + + return 0; + +out_mode_config: + drm_mode_config_cleanup(ddev); + + return ret; +} + + +static void lsdc_mode_config_fini(struct drm_device *ddev) +{ + struct lsdc_device *ldev = to_lsdc(ddev); + + /* disable output polling */ + drm_kms_helper_poll_fini(ddev); + + drm_dev_unregister(ddev); + + devm_free_irq(ddev->dev, ldev->irq, ddev); + + /* shutdown all CRTC, for driver unloading */ + drm_atomic_helper_shutdown(ddev); + + drm_mode_config_cleanup(ddev); +} + +/* + * We need a function to tell different chips apart. + * Because there are difference between the dc in ls7a1000 and the dc in + * ls2k1000, ls7a1000 have two gpio emulated i2c built-in, but ls2k1000 + * don't have such hardware feature. ls2k1000 grab i2c adapter from other + * module, eithor hardware i2c or external gpio-emulated i2c. + * + * Beside, the hardware pixel pll unit is also different. + */ +static int lsdc_determine_chip(struct lsdc_device *ldev) +{ + struct device_node *np; + const char *model; + const char *compat; + unsigned int i; + + for (i = 0; i < ARRAY_SIZE(lsdc_drm_of_match); ++i) { + compat = lsdc_drm_of_match[i].compatible; + + np = of_find_compatible_node(NULL, NULL, compat); + if (np) { + + /* get additional information */ + of_property_read_string(np, "model", &model); + + of_node_put(np); + + ldev->desc = lsdc_drm_of_match[i].data; + + break; + } + } + + if (ldev->desc == NULL) { + drm_err(&ldev->drm, "unknown dc ip core, abort\n"); + return -ENOENT; + } + + drm_info(&ldev->drm, "%s found, model: %s\n", compat, model); + + return 0; +} + + +static int lsdc_drm_suspend(struct device *dev) +{ + struct drm_device *ddev = dev_get_drvdata(dev); + + return drm_mode_config_helper_suspend(ddev); +} + + +static int lsdc_drm_resume(struct device *dev) +{ + struct drm_device *ddev = dev_get_drvdata(dev); + + return drm_mode_config_helper_resume(ddev); +} + + +static int lsdc_pm_freeze(struct device *dev) +{ + return lsdc_drm_suspend(dev); +} + + +static int lsdc_pm_thaw(struct device *dev) +{ + return lsdc_drm_resume(dev); +} + + +static int lsdc_pm_suspend(struct device *dev) +{ + struct pci_dev *pdev = to_pci_dev(dev); + int error; + + error = lsdc_pm_freeze(dev); + if (error) + return error; + + pci_save_state(pdev); + /* Shut down the device */ + pci_disable_device(pdev); + pci_set_power_state(pdev, PCI_D3hot); + + return 0; +} + + +static int lsdc_pm_resume(struct device *dev) +{ + struct pci_dev *pdev = to_pci_dev(dev); + + if (pcim_enable_device(pdev)) + return -EIO; + + pci_set_power_state(pdev, PCI_D0); + + pci_restore_state(pdev); + + return lsdc_pm_thaw(dev); +} + + +static const struct dev_pm_ops lsdc_pm_ops = { + .suspend = lsdc_pm_suspend, + .resume = lsdc_pm_resume, + .freeze = lsdc_pm_freeze, + .thaw = lsdc_pm_thaw, + .poweroff = lsdc_pm_freeze, + .restore = lsdc_pm_resume, +}; + + +static int lsdc_remove_conflicting_framebuffers(const struct drm_driver *drv) +{ + /* lsdc is a pci device, but it don't have a dedicate vram bar because + * of historic reason(The display controller is ported from SoC product + * of Loongson, Loongson 2H series which date back to 2012) + * And simplefb node may have been located anywhere in memory. + */ + return drm_aperture_remove_conflicting_framebuffers(0, ~0, false, drv); +} + + +static int lsdc_vram_init(struct lsdc_device *ldev) +{ + struct drm_device *ddev = &ldev->drm; + struct pci_dev *gpu; + resource_size_t base, size; + int ret; + + /* BAR 2 of LS7A1000's GPU contain VRAM, It's GC1000 */ + gpu = pci_get_device(PCI_VENDOR_ID_LOONGSON, 0x7a15, NULL); + base = pci_resource_start(gpu, 2); + size = pci_resource_len(gpu, 2); + + drm_info(ddev, "vram start: 0x%llx, size: %uMB\n", + base, (unsigned int)(size >> 20)); + + if (!request_mem_region(base, size, "lsdc_vram")) { + drm_err(ddev, "can't reserve VRAM memory region\n"); + return -ENXIO; + } + + if (ldev->use_vram_helper) { +#ifdef CONFIG_DRM_LSDC_VRAM_DRIVER + ret = drmm_vram_helper_init(ddev, base, size); + if (ret) { + drm_err(ddev, "can't init vram helper\n"); + return ret; + } +#endif + } else if (ldev->dirty_update) { + ldev->vram = devm_ioremap_wc(ddev->dev, base, size); + if (ldev->vram == NULL) + return -ENOMEM; + + drm_info(ddev, "vram virtual addr: 0x%llx\n", (u64)ldev->vram); + } + + ldev->vram_base = base; + ldev->vram_size = size; + + return 0; +} + +/* + * For the dc in ls7a1000, it is more reliable scanout from the VRAM. + * scanout from the system memory suffer from some hardware deficiency + * which cause the screen flickering under RAM pressure. + */ +static bool lsdc_should_vram_helper_based(void) +{ + static const char * const dc_compat[] = { "pci0014,7a06.0", + "pci0014,7a06" }; + bool ret = false; + struct device_node *np; + unsigned int i; + + for (i = 0; i < ARRAY_SIZE(dc_compat); ++i) { + np = of_find_compatible_node(NULL, NULL, dc_compat[i]); + if (!np) + continue; + + ret = of_property_read_bool(np, "use_vram_helper"); + of_node_put(np); + break; + } + + if (ret) + DRM_INFO("using vram base solution dictated by device tree\n"); + + return ret; +} + + +static int lsdc_pci_probe(struct pci_dev *pdev, + const struct pci_device_id * const ent) +{ + const struct drm_driver *driver = &lsdc_drm_driver_cma_stub; + struct lsdc_device *ldev; + struct drm_device *ddev; + int ret; + + lsdc_remove_conflicting_framebuffers(driver); + + ret = pci_set_dma_mask(pdev, DMA_BIT_MASK(32)); + if (ret) { + dev_err(&pdev->dev, "Set DMA Mask failed\n"); + return ret; + } + + ret = pcim_enable_device(pdev); + if (ret) { + dev_err(&pdev->dev, "Enable pci devive failed\n"); + return ret; + } + + pci_set_master(pdev); + + /* Get the optional framebuffer memory resource */ + ret = of_reserved_mem_device_init(&pdev->dev); + if (ret && ret != -ENODEV) + return ret; + +#ifdef CONFIG_DRM_LSDC_VRAM_DRIVER + if ((lsdc_use_vram_helper > 0) || lsdc_should_vram_helper_based()) { + driver = &lsdc_vram_driver_stub; + DRM_INFO("using vram helper based solution\n"); + } +#endif + + ldev = devm_drm_dev_alloc(&pdev->dev, + driver, + struct lsdc_device, + drm); + if (IS_ERR(ldev)) + return PTR_ERR(ldev); + + ddev = &ldev->drm; + + pci_set_drvdata(pdev, ddev); + + if (IS_ENABLED(CONFIG_DRM_LSDC_VRAM_DRIVER) && lsdc_use_vram_helper > 0) + ldev->use_vram_helper = true; + else { + if (lsdc_cached_coherent > 0) { + ldev->cached_coherent = true; + drm_info(ddev, "with hardware maintained cached coherent\n"); + } + + if (lsdc_dirty_update > 0) { + ldev->dirty_update = true; + drm_info(ddev, "dirty update enabled\n"); + } + } + + if (lsdc_verbose > 0) + ldev->verbose = true; + + ret = lsdc_determine_chip(ldev); + if (ret) + return ret; + + /* BAR 0 contains registers */ + ldev->reg_base = devm_ioremap_resource(&pdev->dev, &pdev->resource[0]); + if (IS_ERR(ldev->reg_base)) + return PTR_ERR(ldev->reg_base); + + /* LS2K1000/LS2K0500 is SoC, don't have a VRAM */ + if ((ldev->desc->chip == LSDC_CHIP_7A1000) && + (ldev->use_vram_helper || ldev->dirty_update)) + lsdc_vram_init(ldev); + + ret = lsdc_mode_config_init(ldev); + if (ret) + goto err_out; + + + ldev->irq = pdev->irq; + + dev_info(&pdev->dev, "irq = %d\n", ldev->irq); + + ret = devm_request_threaded_irq(&pdev->dev, + pdev->irq, + lsdc_irq_handler_cb, + lsdc_irq_thread_cb, + IRQF_ONESHOT, + dev_name(&pdev->dev), + ddev); + + if (ret) { + dev_err(&pdev->dev, "Failed to register lsdc interrupt\n"); + goto err_out; + } + + ret = drm_vblank_init(ddev, LSDC_MAX_CRTC); + if (ret) { + dev_err(&pdev->dev, + "Fatal error during vblank init: %d\n", ret); + goto err_out; + } + + /* Initialize and enable output polling */ + drm_kms_helper_poll_init(ddev); + + ret = drm_dev_register(ddev, 0); + if (ret) + goto err_out; + + drm_fbdev_generic_setup(ddev, 32); + + return 0; + +err_out: + drm_dev_put(ddev); + + return ret; +} + + +static void lsdc_pci_remove(struct pci_dev *pdev) +{ + struct drm_device *ddev = pci_get_drvdata(pdev); + + lsdc_mode_config_fini(ddev); + + drm_dev_put(ddev); + + pci_clear_master(pdev); + + pci_release_regions(pdev); +} + + +static const struct pci_device_id lsdc_pciid_list[] = { + {PCI_VENDOR_ID_LOONGSON, 0x7a06, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, + {0, 0, 0, 0, 0, 0, 0} +}; + + +static struct pci_driver lsdc_pci_driver = { + .name = "lsdc", + .id_table = lsdc_pciid_list, + .probe = lsdc_pci_probe, + .remove = lsdc_pci_remove, + .driver.pm = &lsdc_pm_ops, +}; + + +static int __init lsdc_drm_init(void) +{ + struct pci_dev *pdev = NULL; + + if (drm_firmware_drivers_only()) + return -EINVAL; + + if (lsdc_modeset == 0) + return -ENOENT; + + while ((pdev = pci_get_class(PCI_CLASS_DISPLAY_VGA << 8, pdev))) { + /* + * Multiple video card workaround + * + * This integrated video driver will always be selected as + * default boot device by vgaarb system. + */ + if (pdev->vendor != PCI_VENDOR_ID_LOONGSON) { + DRM_INFO("Discrete graphic card detected, abort\n"); + return 0; + } + } + + return pci_register_driver(&lsdc_pci_driver); +} +module_init(lsdc_drm_init); + +static void __exit lsdc_drm_exit(void) +{ + pci_unregister_driver(&lsdc_pci_driver); +} +module_exit(lsdc_drm_exit); + + +MODULE_DEVICE_TABLE(pci, lsdc_pciid_list); +MODULE_AUTHOR(DRIVER_AUTHOR); +MODULE_DESCRIPTION(DRIVER_DESC); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/gpu/drm/lsdc/lsdc_drv.h b/drivers/gpu/drm/lsdc/lsdc_drv.h new file mode 100644 index 000000000000..89cf15248c3a --- /dev/null +++ b/drivers/gpu/drm/lsdc/lsdc_drv.h @@ -0,0 +1,216 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2020 Loongson Corporation + * + * Permission is hereby granted, free of charge, to any person obtaining a + * copy of this software and associated documentation files (the + * "Software"), to deal in the Software without restriction, including + * without limitation the rights to use, copy, modify, merge, publish, + * distribute, sub license, and/or sell copies of the Software, and to + * permit persons to whom the Software is furnished to do so, subject to + * the following conditions: + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IN NO EVENT SHALL + * THE COPYRIGHT HOLDERS, AUTHORS AND/OR ITS SUPPLIERS BE LIABLE FOR ANY CLAIM, + * DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR + * OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE + * USE OR OTHER DEALINGS IN THE SOFTWARE. + * + * The above copyright notice and this permission notice (including the + * next paragraph) shall be included in all copies or substantial portions + * of the Software. + */ + +/* + * Authors: + * Sui Jingfeng suijingfeng@loongson.cn + */ + +#ifndef __LSDC_DRV_H__ +#define __LSDC_DRV_H__ + +#include <drm/drm_print.h> +#include <drm/drm_device.h> +#include <drm/drm_crtc.h> +#include <drm/drm_plane.h> +#include <drm/drm_encoder.h> + +#ifdef CONFIG_DRM_LSDC_VRAM_DRIVER +#include <drm/drm_gem_vram_helper.h> +#endif + +#include "lsdc_regs.h" +#include "lsdc_pll.h" + +#define LSDC_MAX_CRTC 2 + +/* There is only a 1:1 mapping of encoders and connectors for lsdc */ +/* + * +-------------------+ _________ + * | | | | + * | CRTC0 --> DVO0 ---------> Encoder0 --> Connector0 ---> | Monotor | + * | | ^ ^ |_________| + * | | | | + * | <----- i2c0 ----------------+ + * | LSDC IP CORE | + * | <----- i2c1 ----------------+ + * | | | | _________ + * | | | | | | + * | CRTC1 --> DVO1 ---------> Encoder1 --> Connector1 ---> | Panel | + * | | |_________| + * +-------------------+ + */ + +enum loongson_dc_family { + LSDC_CHIP_UNKNOWN = 0, + LSDC_CHIP_2K1000 = 1, /* 2-Core SoC, 64-bit */ + LSDC_CHIP_7A1000 = 2, /* North bridge of LS3A3000/LS3A4000/LS3A5000 */ + LSDC_CHIP_2K0500 = 3, /* Reduced version of LS2K1000, single core */ + LSDC_CHIP_7A2000 = 4, /* Enhancement version of 7A1000 */ + LSDC_CHIP_LAST, +}; + +enum lsdc_pixel_format { + LSDC_PF_NONE = 0, + LSDC_PF_ARGB4444 = 1, /* ARGB A:4 bits R/G/B: 4 bits each [16 bits] */ + LSDC_PF_ARGB1555 = 2, /* ARGB A:1 bit RGB:15 bits [16 bits] */ + LSDC_PF_RGB565 = 3, /* RGB [16 bits] */ + LSDC_PF_XRGB8888 = 4, /* XRGB [32 bits] */ +}; + +struct lsdc_chip_desc { + enum loongson_dc_family chip; + uint32_t num_of_crtc; + + uint32_t max_pixel_clk; + + uint32_t max_width; + uint32_t max_height; + + uint32_t num_of_hw_cursor; + uint32_t hw_cursor_w; + uint32_t hw_cursor_h; + bool have_builtin_i2c; + uint32_t stride_alignment; +}; + + +/** + * struct lsdc_display_pipe - simple display pipeline + * @crtc: CRTC control structure + * @plane: Plane control structure + * @encoder: Encoder control structure + * @pixpll: Pll control structure + * @connector: point to connector control structure + * + * display pipeline with plane, crtc, encoder, pll collapsed into one + * entity. It should be initialized by calling drm_simple_display_pipe_init(). + */ +struct lsdc_display_pipe { + struct drm_crtc crtc; + struct drm_plane primary; + struct drm_plane cursor; + struct drm_encoder encoder; + struct lsdc_pll pixpll; + struct lsdc_connector *lconn; + + int index; + bool available; +}; + + +struct lsdc_crtc_state { + struct drm_crtc_state base; + struct lsdc_pll_core_values pparams; + unsigned int pix_fmt; +}; + + +struct lsdc_device { + struct drm_device drm; + + void __iomem *reg_base; + void __iomem *vram; + resource_size_t vram_base; + resource_size_t vram_size; + + struct lsdc_display_pipe disp_pipe[LSDC_MAX_CRTC]; + + unsigned int num_output; + + /* platform specific data */ + const struct lsdc_chip_desc *desc; + + /* @reglock: protects concurrent register access */ + spinlock_t reglock; + + /* + * @dirty_update: true if manual dirty update is wantted + */ + bool dirty_update; + /* + * @cached_coherent: true if the host platform is hardware maintained + * cached coherent. + */ + bool cached_coherent; + /* + * @use_vram_helper: using vram helper instead of cma helper base + * solution. As ls7a1000 has a dediacted video ram, the dc scanout + * from the vram is more reliable. + */ + bool use_vram_helper; + + /* + * @verbose: set it to true if print useful information is wantted + */ + bool verbose; + + int irq; + u32 irq_status; +}; + +#define to_lsdc(x) container_of(x, struct lsdc_device, drm) + +static inline struct lsdc_crtc_state * +to_lsdc_crtc_state(struct drm_crtc_state *base) +{ + return container_of(base, struct lsdc_crtc_state, base); +} + +static inline u32 lsdc_reg_read32(struct lsdc_device * const ldev, u32 offset) +{ + u32 val; + unsigned long flags; + + spin_lock_irqsave(&ldev->reglock, flags); + val = readl(ldev->reg_base + offset); + spin_unlock_irqrestore(&ldev->reglock, flags); + + return val; +} + +static inline void lsdc_reg_write32(struct lsdc_device * const ldev, u32 offset, u32 val) +{ + unsigned long flags; + + spin_lock_irqsave(&ldev->reglock, flags); + writel(val, ldev->reg_base + offset); + spin_unlock_irqrestore(&ldev->reglock, flags); +} + +int lsdc_crtc_init(struct drm_device *ddev, struct drm_crtc *crtc, + unsigned int index, struct drm_plane *primary, + struct drm_plane *cursor); + +int lsdc_plane_init(struct lsdc_device *ldev, struct drm_plane *plane, + enum drm_plane_type type, unsigned int index); + +int lsdc_encoder_init(struct drm_encoder * const encoder, + struct drm_connector *connector, + struct drm_device *ddev, + unsigned int index, + unsigned int total); + +#endif diff --git a/drivers/gpu/drm/lsdc/lsdc_encoder.c b/drivers/gpu/drm/lsdc/lsdc_encoder.c new file mode 100644 index 000000000000..0cdd95f5bc37 --- /dev/null +++ b/drivers/gpu/drm/lsdc/lsdc_encoder.c @@ -0,0 +1,79 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2020 Loongson Corporation + * + * Permission is hereby granted, free of charge, to any person obtaining a + * copy of this software and associated documentation files (the + * "Software"), to deal in the Software without restriction, including + * without limitation the rights to use, copy, modify, merge, publish, + * distribute, sub license, and/or sell copies of the Software, and to + * permit persons to whom the Software is furnished to do so, subject to + * the following conditions: + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IN NO EVENT SHALL + * THE COPYRIGHT HOLDERS, AUTHORS AND/OR ITS SUPPLIERS BE LIABLE FOR ANY CLAIM, + * DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR + * OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE + * USE OR OTHER DEALINGS IN THE SOFTWARE. + * + * The above copyright notice and this permission notice (including the + * next paragraph) shall be included in all copies or substantial portions + * of the Software. + */ + +/* + * Authors: + * Sui Jingfeng suijingfeng@loongson.cn + */ +#include <drm/drm_print.h> +#include <drm/drm_crtc_helper.h> + +#include "lsdc_drv.h" + +static const struct drm_encoder_funcs lsdc_encoder_funcs = { + .destroy = drm_encoder_cleanup, +}; + + +int lsdc_encoder_init(struct drm_encoder * const encoder, + struct drm_connector *connector, + struct drm_device *ddev, + unsigned int index, + unsigned int total) +{ + int ret; + int type; + + encoder->possible_crtcs = BIT(index); + + if (total == 2) + encoder->possible_clones = BIT(1) | BIT(0); + else if (total < 2) + encoder->possible_clones = 0; + + if (connector->connector_type == DRM_MODE_CONNECTOR_VGA) + type = DRM_MODE_ENCODER_DAC; + else if ((connector->connector_type == DRM_MODE_CONNECTOR_HDMIA) || + (connector->connector_type == DRM_MODE_CONNECTOR_HDMIB) || + (connector->connector_type == DRM_MODE_CONNECTOR_DVID)) + type = DRM_MODE_ENCODER_TMDS; + else if (connector->connector_type == DRM_MODE_CONNECTOR_DPI) + type = DRM_MODE_ENCODER_DPI; + else if (connector->connector_type == DRM_MODE_CONNECTOR_VIRTUAL) + type = DRM_MODE_ENCODER_VIRTUAL; + else + type = DRM_MODE_ENCODER_NONE; + + ret = drm_encoder_init(ddev, + encoder, + &lsdc_encoder_funcs, + type, + "encoder%d", + index); + if (ret) + return ret; + + return drm_connector_attach_encoder(connector, encoder); +} diff --git a/drivers/gpu/drm/lsdc/lsdc_i2c.c b/drivers/gpu/drm/lsdc/lsdc_i2c.c new file mode 100644 index 000000000000..895e94ae6827 --- /dev/null +++ b/drivers/gpu/drm/lsdc/lsdc_i2c.c @@ -0,0 +1,220 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2020 Loongson Corporation + * + * Permission is hereby granted, free of charge, to any person obtaining a + * copy of this software and associated documentation files (the + * "Software"), to deal in the Software without restriction, including + * without limitation the rights to use, copy, modify, merge, publish, + * distribute, sub license, and/or sell copies of the Software, and to + * permit persons to whom the Software is furnished to do so, subject to + * the following conditions: + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IN NO EVENT SHALL + * THE COPYRIGHT HOLDERS, AUTHORS AND/OR ITS SUPPLIERS BE LIABLE FOR ANY CLAIM, + * DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR + * OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE + * USE OR OTHER DEALINGS IN THE SOFTWARE. + * + * The above copyright notice and this permission notice (including the + * next paragraph) shall be included in all copies or substantial portions + * of the Software. + */ + +/* + * Authors: + * Sui Jingfeng suijingfeng@loongson.cn + */ + +#include <linux/string.h> +#include <linux/i2c.h> + +#include "lsdc_drv.h" +#include "lsdc_regs.h" +#include "lsdc_i2c.h" + +/* + * set the state of a gpio pin indicated by mask + * @mask: gpio pin mask + */ +static void ls7a_gpio_i2c_set(struct lsdc_i2c * const i2c, int mask, int state) +{ + struct lsdc_device *ldev = to_lsdc(i2c->ddev); + u8 val; + unsigned long flags; + + spin_lock_irqsave(&ldev->reglock, flags); + + if (state) { + val = readb(i2c->dir_reg); + val |= mask; + writeb(val, i2c->dir_reg); + } else { + val = readb(i2c->dir_reg); + val &= ~mask; + writeb(val, i2c->dir_reg); + + val = readb(i2c->dat_reg); + if (state) + val |= mask; + else + val &= ~mask; + writeb(val, i2c->dat_reg); + } + + spin_unlock_irqrestore(&ldev->reglock, flags); +} + +/* + * read value back from gpio pin + * @mask: gpio pin mask + */ +static int ls7a_gpio_i2c_get(struct lsdc_i2c * const i2c, int mask) +{ + struct lsdc_device *ldev = to_lsdc(i2c->ddev); + u8 val; + unsigned long flags; + + spin_lock_irqsave(&ldev->reglock, flags); + + /* first set this pin as input */ + val = readb(i2c->dir_reg); + val |= mask; + writeb(val, i2c->dir_reg); + + /* then get level state from this pin */ + val = readb(i2c->dat_reg); + + spin_unlock_irqrestore(&ldev->reglock, flags); + + return (val & mask) ? 1 : 0; +} + + +/* set the state on the i2c->sda pin */ +static void ls7a_i2c_set_sda(void *i2c, int state) +{ + struct lsdc_i2c * const li2c = (struct lsdc_i2c *)i2c; + + return ls7a_gpio_i2c_set(li2c, li2c->sda, state); +} + +/* set the state on the i2c->scl pin */ +static void ls7a_i2c_set_scl(void *i2c, int state) +{ + struct lsdc_i2c * const li2c = (struct lsdc_i2c *)i2c; + + return ls7a_gpio_i2c_set(li2c, li2c->scl, state); +} + +/* read the value from the i2c->sda pin */ +static int ls7a_i2c_get_sda(void *i2c) +{ + struct lsdc_i2c * const li2c = (struct lsdc_i2c *)i2c; + + return ls7a_gpio_i2c_get(li2c, li2c->sda); +} + +/* read the value from the i2c->scl pin */ +static int ls7a_i2c_get_scl(void *i2c) +{ + struct lsdc_i2c * const li2c = (struct lsdc_i2c *)i2c; + + return ls7a_gpio_i2c_get(li2c, li2c->scl); +} + +/* + * Get i2c id from connector id + * + * TODO: get it from dtb + */ +static int lsdc_get_i2c_id(struct drm_device *ddev, unsigned int index) +{ + return index; +} + +/* + * mainly for dc in ls7a1000 which have builtin gpio emulated i2c + * + * @index : output channel index, 0 for DVO0, 1 for DVO1 + */ +struct i2c_adapter *lsdc_create_i2c_chan(struct drm_device *ddev, + unsigned int index) +{ + struct lsdc_device *ldev = to_lsdc(ddev); + struct i2c_adapter *adapter; + struct lsdc_i2c *li2c; + int ret; + + li2c = devm_kzalloc(ddev->dev, sizeof(*li2c), GFP_KERNEL); + if (li2c == NULL) + return ERR_PTR(-ENOMEM); + + li2c->ddev = ddev; + + if (index == 0) { + li2c->sda = 0x01; + li2c->scl = 0x02; + } else if (index == 1) { + li2c->sda = 0x04; + li2c->scl = 0x08; + } + + li2c->dir_reg = ldev->reg_base + LS7A_DC_GPIO_DIR_REG; + li2c->dat_reg = ldev->reg_base + LS7A_DC_GPIO_DAT_REG; + + li2c->bit.setsda = ls7a_i2c_set_sda; + li2c->bit.setscl = ls7a_i2c_set_scl; + li2c->bit.getsda = ls7a_i2c_get_sda; + li2c->bit.getscl = ls7a_i2c_get_scl; + li2c->bit.udelay = 5; + li2c->bit.timeout = usecs_to_jiffies(2200); /* from VESA */ + li2c->bit.data = li2c; + + adapter = &li2c->adapter; + + adapter->algo_data = &li2c->bit; + adapter->owner = THIS_MODULE; + adapter->class = I2C_CLASS_DDC; + adapter->dev.parent = ddev->dev; + adapter->nr = -1; + + snprintf(adapter->name, sizeof(adapter->name), + "%s-%d", "lsdc_gpio_i2c", index); + + i2c_set_adapdata(adapter, li2c); + + ret = i2c_bit_add_numbered_bus(adapter); + if (ret) { + devm_kfree(ddev->dev, li2c); + return ERR_PTR(ret); + } + + return adapter; +} + + +/* + * Mainly for dc in ls2k1000, ls2k0500 SoC which should get a i2c adapter + * from i2c susystem. + * + * @index : output channel index, 0 for DVO0, 1 for DVO1 + */ +struct i2c_adapter *lsdc_get_i2c_adapter(struct drm_device *ddev, + unsigned int index) +{ + unsigned int i2c_id; + + /* find mapping between i2c id and connector id */ + i2c_id = lsdc_get_i2c_id(ddev, index); + + return i2c_get_adapter(i2c_id); +} + + +void lsdc_destroy_i2c(struct drm_device *ddev, struct i2c_adapter *adapter) +{ + i2c_put_adapter(adapter); +} diff --git a/drivers/gpu/drm/lsdc/lsdc_i2c.h b/drivers/gpu/drm/lsdc/lsdc_i2c.h new file mode 100644 index 000000000000..f4560db3694a --- /dev/null +++ b/drivers/gpu/drm/lsdc/lsdc_i2c.h @@ -0,0 +1,61 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2020 Loongson Corporation + * + * Permission is hereby granted, free of charge, to any person obtaining a + * copy of this software and associated documentation files (the + * "Software"), to deal in the Software without restriction, including + * without limitation the rights to use, copy, modify, merge, publish, + * distribute, sub license, and/or sell copies of the Software, and to + * permit persons to whom the Software is furnished to do so, subject to + * the following conditions: + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IN NO EVENT SHALL + * THE COPYRIGHT HOLDERS, AUTHORS AND/OR ITS SUPPLIERS BE LIABLE FOR ANY CLAIM, + * DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR + * OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE + * USE OR OTHER DEALINGS IN THE SOFTWARE. + * + * The above copyright notice and this permission notice (including the + * next paragraph) shall be included in all copies or substantial portions + * of the Software. + */ + +/* + * Authors: + * Sui Jingfeng suijingfeng@loongson.cn + */ + + +#ifndef __LSDC_I2C__ +#define __LSDC_I2C__ + +#include <linux/i2c.h> +#include <linux/i2c-algo-bit.h> + + +struct lsdc_i2c { + struct drm_device *ddev; + struct i2c_adapter adapter; + struct i2c_algo_bit_data bit; + /* pin bit mask */ + u8 sda; + u8 scl; + + void __iomem *dir_reg; + void __iomem *dat_reg; +}; + + +void lsdc_destroy_i2c(struct drm_device *ddev, struct i2c_adapter *i2c); + +struct i2c_adapter *lsdc_create_i2c_chan(struct drm_device *ddev, + unsigned int con_id); + +struct i2c_adapter *lsdc_get_i2c_adapter(struct drm_device *ddev, + unsigned int con_id); + + +#endif diff --git a/drivers/gpu/drm/lsdc/lsdc_irq.c b/drivers/gpu/drm/lsdc/lsdc_irq.c new file mode 100644 index 000000000000..7620de54aae4 --- /dev/null +++ b/drivers/gpu/drm/lsdc/lsdc_irq.c @@ -0,0 +1,77 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2020 Loongson Corporation + * + * Permission is hereby granted, free of charge, to any person obtaining a + * copy of this software and associated documentation files (the + * "Software"), to deal in the Software without restriction, including + * without limitation the rights to use, copy, modify, merge, publish, + * distribute, sub license, and/or sell copies of the Software, and to + * permit persons to whom the Software is furnished to do so, subject to + * the following conditions: + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IN NO EVENT SHALL + * THE COPYRIGHT HOLDERS, AUTHORS AND/OR ITS SUPPLIERS BE LIABLE FOR ANY CLAIM, + * DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR + * OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE + * USE OR OTHER DEALINGS IN THE SOFTWARE. + * + * The above copyright notice and this permission notice (including the + * next paragraph) shall be included in all copies or substantial portions + * of the Software. + */ + +/* + * Authors: + * Sui Jingfeng suijingfeng@loongson.cn + */ +#include <drm/drm_vblank.h> + +#include "lsdc_drv.h" +#include "lsdc_regs.h" +#include "lsdc_irq.h" + +/* Function to be called in a threaded interrupt context. */ +irqreturn_t lsdc_irq_thread_cb(int irq, void *arg) +{ + struct drm_device *ddev = arg; + struct lsdc_device *ldev = to_lsdc(ddev); + struct drm_crtc *crtc; + + /* trigger the vblank event */ + if (ldev->irq_status & INT_CRTC0_VS) { + crtc = drm_crtc_from_index(ddev, 0); + drm_crtc_handle_vblank(crtc); + } + + if (ldev->irq_status & INT_CRTC1_VS) { + crtc = drm_crtc_from_index(ddev, 1); + drm_crtc_handle_vblank(crtc); + } + + lsdc_reg_write32(ldev, LSDC_INT_REG, INT_CRTC0_VS_EN | INT_CRTC1_VS_EN); + + return IRQ_HANDLED; +} + + +/* Function to be called when the IRQ occurs */ +irqreturn_t lsdc_irq_handler_cb(int irq, void *arg) +{ + struct drm_device *ddev = arg; + struct lsdc_device *ldev = to_lsdc(ddev); + + /* Read & Clear the interrupt status */ + ldev->irq_status = lsdc_reg_read32(ldev, LSDC_INT_REG); + if ((ldev->irq_status & INT_STATUS_MASK) == 0) { + drm_warn(ddev, "no interrupt occurs\n"); + return IRQ_NONE; + } + + /* clear all interrupt */ + lsdc_reg_write32(ldev, LSDC_INT_REG, ldev->irq_status); + + return IRQ_WAKE_THREAD; +} diff --git a/drivers/gpu/drm/lsdc/lsdc_irq.h b/drivers/gpu/drm/lsdc/lsdc_irq.h new file mode 100644 index 000000000000..ac187538d746 --- /dev/null +++ b/drivers/gpu/drm/lsdc/lsdc_irq.h @@ -0,0 +1,37 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2020 Loongson Corporation + * + * Permission is hereby granted, free of charge, to any person obtaining a + * copy of this software and associated documentation files (the + * "Software"), to deal in the Software without restriction, including + * without limitation the rights to use, copy, modify, merge, publish, + * distribute, sub license, and/or sell copies of the Software, and to + * permit persons to whom the Software is furnished to do so, subject to + * the following conditions: + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IN NO EVENT SHALL + * THE COPYRIGHT HOLDERS, AUTHORS AND/OR ITS SUPPLIERS BE LIABLE FOR ANY CLAIM, + * DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR + * OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE + * USE OR OTHER DEALINGS IN THE SOFTWARE. + * + * The above copyright notice and this permission notice (including the + * next paragraph) shall be included in all copies or substantial portions + * of the Software. + */ + +/* + * Authors: + * Sui Jingfeng suijingfeng@loongson.cn + */ + +#ifndef __LSDC_IRQ_H__ +#define __LSDC_IRQ_H__ + +irqreturn_t lsdc_irq_thread_cb(int irq, void *arg); +irqreturn_t lsdc_irq_handler_cb(int irq, void *arg); + +#endif diff --git a/drivers/gpu/drm/lsdc/lsdc_plane.c b/drivers/gpu/drm/lsdc/lsdc_plane.c new file mode 100644 index 000000000000..62801e100a13 --- /dev/null +++ b/drivers/gpu/drm/lsdc/lsdc_plane.c @@ -0,0 +1,681 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2020 Loongson Corporation + * + * Permission is hereby granted, free of charge, to any person obtaining a + * copy of this software and associated documentation files (the + * "Software"), to deal in the Software without restriction, including + * without limitation the rights to use, copy, modify, merge, publish, + * distribute, sub license, and/or sell copies of the Software, and to + * permit persons to whom the Software is furnished to do so, subject to + * the following conditions: + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IN NO EVENT SHALL + * THE COPYRIGHT HOLDERS, AUTHORS AND/OR ITS SUPPLIERS BE LIABLE FOR ANY CLAIM, + * DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR + * OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE + * USE OR OTHER DEALINGS IN THE SOFTWARE. + * + * The above copyright notice and this permission notice (including the + * next paragraph) shall be included in all copies or substantial portions + * of the Software. + */ + +/* + * Authors: + * Sui Jingfeng suijingfeng@loongson.cn + */ + +#include <drm/drm_print.h> +#include <drm/drm_device.h> +#include <drm/drm_crtc.h> +#include <drm/drm_plane.h> +#include <drm/drm_atomic.h> +#include <drm/drm_vblank.h> +#include <drm/drm_drv.h> + +#include <drm/drm_format_helper.h> +#include <drm/drm_plane_helper.h> +#include <drm/drm_fb_cma_helper.h> +#include <drm/drm_gem_cma_helper.h> +#include <drm/drm_atomic_helper.h> +#include <drm/drm_gem_framebuffer_helper.h> +#include <drm/drm_gem_atomic_helper.h> +#include <drm/drm_damage_helper.h> + + +#include "lsdc_drv.h" +#include "lsdc_regs.h" +#include "lsdc_pll.h" + + +static const uint32_t lsdc_primary_formats[] = { + DRM_FORMAT_RGB565, + DRM_FORMAT_XRGB8888, + DRM_FORMAT_ARGB8888, +}; + +static const uint32_t lsdc_cursor_formats[] = { + DRM_FORMAT_ARGB8888, +}; + +static const u64 lsdc_fb_format_modifiers[] = { + DRM_FORMAT_MOD_LINEAR, + DRM_FORMAT_MOD_INVALID +}; + + +static u32 lsdc_pixfmt_to_drm_pixfmt(enum lsdc_pixel_format pf) +{ + switch (pf) { + case LSDC_PF_XRGB8888: + return DRM_FORMAT_XRGB8888; + case LSDC_PF_RGB565: + return DRM_FORMAT_RGB565; + case LSDC_PF_ARGB1555: + return DRM_FORMAT_ARGB1555; + case LSDC_PF_ARGB4444: + return DRM_FORMAT_ARGB4444; + case LSDC_PF_NONE: + default: + return 0; + } +} + +static const char *lsdc_pixfmt_to_string(u32 reg) +{ + switch (reg & CFG_PIX_FMT_MASK) { + case LSDC_PF_XRGB8888: + return "XRGB8888"; + case LSDC_PF_RGB565: + return "RGB565"; + case LSDC_PF_ARGB1555: + return "ARGB1555"; + case LSDC_PF_ARGB4444: + return "ARGB4444"; + case LSDC_PF_NONE: + return "NONE"; + default: + return "unknown"; + } +} + + + +static void lsdc_update_fb_format(struct lsdc_device *ldev, + struct drm_crtc *crtc, + const struct drm_format_info *fmt_info) +{ + unsigned int index = drm_crtc_index(crtc); + u32 val = 0; + u32 fmt; + + switch (fmt_info->format) { + case DRM_FORMAT_RGB565: + fmt = LSDC_PF_RGB565; + break; + case DRM_FORMAT_XRGB8888: + fmt = LSDC_PF_XRGB8888; + break; + case DRM_FORMAT_ARGB8888: + fmt = LSDC_PF_XRGB8888; + break; + default: + fmt = LSDC_PF_XRGB8888; + break; + } + + if (ldev->verbose) + drm_info(&ldev->drm, "fmt wanted is %s\n", + lsdc_pixfmt_to_string(fmt)); + + if (index == 0) { + val = lsdc_reg_read32(ldev, LSDC_CRTC0_CFG_REG); + val = (val & ~CFG_PIX_FMT_MASK) | fmt; + lsdc_reg_write32(ldev, LSDC_CRTC0_CFG_REG, val); + val = lsdc_reg_read32(ldev, LSDC_CRTC0_CFG_REG); + } else if (index == 1) { + val = lsdc_reg_read32(ldev, LSDC_CRTC1_CFG_REG); + val = (val & ~CFG_PIX_FMT_MASK) | fmt; + lsdc_reg_write32(ldev, LSDC_CRTC1_CFG_REG, val); + val = lsdc_reg_read32(ldev, LSDC_CRTC1_CFG_REG); + } + + if (ldev->verbose) + drm_info(&ldev->drm, "after update fb%d format is %s\n", + index, lsdc_pixfmt_to_string(val)); +} + + +static u32 lsdc_primary_get_default_format(struct drm_crtc *crtc) +{ + struct lsdc_device *ldev = to_lsdc(crtc->dev); + unsigned int index = drm_crtc_index(crtc); + u32 val; + + if (index == 0) + val = lsdc_reg_read32(ldev, LSDC_CRTC0_CFG_REG); + else if (index == 1) + val = lsdc_reg_read32(ldev, LSDC_CRTC1_CFG_REG); + + return val & CFG_PIX_FMT_MASK; +} + + +static void lsdc_update_fb_start_addr(struct lsdc_device *ldev, + struct drm_crtc *crtc, + u64 paddr) +{ + unsigned int index = drm_crtc_index(crtc); + u32 addr_reg; + u32 cfg_reg; + u32 val; + + /* + * Find which framebuffer address register should update. + * if FB_ADDR0_REG is in using, we write the addr to FB_ADDR1_REG, + * if FB_ADDR1_REG is in using, we write the addr to FB_ADDR0_REG + */ + if (index == 0) { + /* CRTC0 */ + val = lsdc_reg_read32(ldev, LSDC_CRTC0_CFG_REG); + + cfg_reg = LSDC_CRTC0_CFG_REG; + + if (val & CFG_FB_IDX_BIT) { + addr_reg = LSDC_CRTC0_FB_ADDR0_REG; + drm_dbg_kms(&ldev->drm, "CRTC0 FB0 will be use\n"); + } else { + addr_reg = LSDC_CRTC0_FB_ADDR1_REG; + drm_dbg_kms(&ldev->drm, "CRTC0 FBq will be use\n"); + } + } else if (index == 1) { + /* CRTC1 */ + val = lsdc_reg_read32(ldev, LSDC_CRTC1_CFG_REG); + + cfg_reg = LSDC_CRTC1_CFG_REG; + + if (val & CFG_FB_IDX_BIT) { + addr_reg = LSDC_CRTC1_FB_ADDR0_REG; + drm_dbg_kms(&ldev->drm, "CRTC1 FB0 will be use\n"); + } else { + addr_reg = LSDC_CRTC1_FB_ADDR1_REG; + drm_dbg_kms(&ldev->drm, "CRTC1 FBq will be use\n"); + } + } + + lsdc_reg_write32(ldev, addr_reg, paddr); + + /* + * Then, we triger the fb switch, the switch of the framebuffer + * to be scanout will complete at the next vblank. + */ + lsdc_reg_write32(ldev, cfg_reg, val | CFG_PAGE_FLIP_BIT); + + drm_dbg_kms(&ldev->drm, "crtc%u scantout from 0x%llx\n", index, paddr); +} + + +static void lsdc_handle_damage(struct lsdc_device *ldev, + struct drm_framebuffer *fb, + struct drm_rect *clip, + void *src) +{ + unsigned int offset; + void __iomem *dst; + + offset = drm_fb_clip_offset(fb->pitches[0], fb->format, clip); + dst = ldev->vram + offset; + drm_fb_memcpy_toio(dst, fb->pitches[0], src, fb, clip); +} + + +static unsigned int lsdc_get_fb_offset(struct drm_framebuffer *fb, + struct drm_plane_state *state, + unsigned int plane) +{ + unsigned int offset; + + offset = fb->offsets[plane]; + offset += fb->format->cpp[plane] * (state->src_x >> 16); + offset += fb->pitches[plane] * (state->src_y >> 16); + + return offset; +} + +#ifdef CONFIG_DRM_LSDC_VRAM_DRIVER +static s64 lsdc_get_vram_bo_offset(struct drm_framebuffer *fb) +{ + struct drm_gem_vram_object *gbo; + s64 gpu_addr; + + gbo = drm_gem_vram_of_gem(fb->obj[0]); + gpu_addr = drm_gem_vram_offset(gbo); + + return gpu_addr; +} +#endif + + +static int lsdc_primary_plane_atomic_check(struct drm_plane *plane, + struct drm_atomic_state *state) +{ + struct drm_device *ddev = plane->dev; + struct lsdc_device *ldev = to_lsdc(ddev); + struct drm_plane_state *old_plane_state = drm_atomic_get_old_plane_state(state, plane); + struct drm_plane_state *new_plane_state = drm_atomic_get_new_plane_state(state, plane); + struct drm_framebuffer *new_fb = new_plane_state->fb; + struct drm_framebuffer *old_fb = old_plane_state->fb; + struct drm_crtc *crtc = new_plane_state->crtc; + u32 new_format = new_fb->format->format; + struct drm_crtc_state *new_crtc_state; + struct lsdc_crtc_state *priv_crtc_state; + int ret; + + if (!crtc) + return 0; + + new_crtc_state = drm_atomic_get_new_crtc_state(state, crtc); + if (WARN_ON(!new_crtc_state)) + return -EINVAL; + + priv_crtc_state = to_lsdc_crtc_state(new_crtc_state); + + ret = drm_atomic_helper_check_plane_state(new_plane_state, + new_crtc_state, + DRM_PLANE_HELPER_NO_SCALING, + DRM_PLANE_HELPER_NO_SCALING, + false, + true); + if (ret) + return ret; + + /* + * Require full modeset if enabling or disabling a plane, + * or changing its position, size, depth or format. + */ + if ((!new_fb || !old_fb || + old_plane_state->crtc_x != new_plane_state->crtc_x || + old_plane_state->crtc_y != new_plane_state->crtc_y || + old_plane_state->crtc_w != new_plane_state->crtc_w || + old_plane_state->crtc_h != new_plane_state->crtc_h || + old_fb->format->format != new_format)) + new_crtc_state->mode_changed = true; + + + priv_crtc_state->pix_fmt = lsdc_primary_get_default_format(crtc); + + if (lsdc_pixfmt_to_drm_pixfmt(priv_crtc_state->pix_fmt) != new_format) { + drm_info(&ldev->drm, "mode changed\n"); + new_crtc_state->mode_changed = true; + } + + if (new_crtc_state->mode_changed) { + struct lsdc_display_pipe *dispipe = container_of(plane, struct lsdc_display_pipe, primary); + struct lsdc_pll *pixpll = &dispipe->pixpll; + const struct lsdc_pixpll_funcs *pfuncs = pixpll->funcs; + + ret = pfuncs->compute(pixpll, + new_crtc_state->mode.clock, + true, + &priv_crtc_state->pparams); + if (ret == false) { + drm_warn(plane->dev, + "failed find a set of pll param for mode %u\n", + new_crtc_state->mode.clock); + return -EINVAL; + } + } + + if (ldev->dirty_update) + drm_atomic_helper_check_plane_damage(state, new_plane_state); + + return 0; +} + +static void lsdc_update_stride(struct lsdc_device *ldev, + struct drm_crtc *crtc, + unsigned int stride) +{ + unsigned int index = drm_crtc_index(crtc); + + if (index == 0) + lsdc_reg_write32(ldev, LSDC_CRTC0_STRIDE_REG, stride); + else if (index == 1) + lsdc_reg_write32(ldev, LSDC_CRTC1_STRIDE_REG, stride); + + drm_dbg_kms(&ldev->drm, "update stride to %u\n", stride); +} + + + +static void lsdc_primary_plane_atomic_update(struct drm_plane *plane, + struct drm_atomic_state *state) +{ + struct lsdc_device *ldev = to_lsdc(plane->dev); + struct drm_plane_state *new_plane_state = drm_atomic_get_new_plane_state(state, plane); + struct drm_crtc *crtc = new_plane_state->crtc; + struct drm_framebuffer *fb = new_plane_state->fb; + u32 fb_offset = lsdc_get_fb_offset(fb, new_plane_state, 0); + struct drm_gem_cma_object *obj; + dma_addr_t fb_addr; + + if (ldev->use_vram_helper) { +#ifdef CONFIG_DRM_LSDC_VRAM_DRIVER + s64 gpu_addr; + + gpu_addr = lsdc_get_vram_bo_offset(fb); + if (gpu_addr < 0) + return; + + fb_addr = ldev->vram_base + gpu_addr + fb_offset; +#endif + } else { + obj = drm_fb_cma_get_gem_obj(fb, 0); + + if (ldev->dirty_update) + fb_addr = ldev->vram_base + fb_offset; + else + fb_addr = obj->paddr + fb_offset; + } + + lsdc_update_fb_start_addr(ldev, crtc, fb_addr); + + lsdc_update_stride(ldev, crtc, fb->pitches[0]); + + if (drm_atomic_crtc_needs_modeset(crtc->state)) + lsdc_update_fb_format(ldev, crtc, fb->format); + + if (ldev->dirty_update) { + struct drm_plane_state *old_plane_state; + struct drm_rect damage; + bool valid; + + old_plane_state = drm_atomic_get_old_plane_state(state, plane); + + valid = drm_atomic_helper_damage_merged(old_plane_state, + new_plane_state, + &damage); + if (valid) + lsdc_handle_damage(ldev, fb, &damage, obj->vaddr); + } +} + + +static void lsdc_primary_plane_atomic_disable(struct drm_plane *plane, + struct drm_atomic_state *state) +{ + drm_dbg_kms(plane->dev, "%s disabled\n", plane->name); +} + + +static int lsdc_plane_prepare_fb(struct drm_plane *plane, + struct drm_plane_state *new_state) +{ +#ifdef CONFIG_DRM_LSDC_VRAM_DRIVER + struct lsdc_device *ldev = to_lsdc(plane->dev); + + if (ldev->use_vram_helper) + return drm_gem_vram_plane_helper_prepare_fb(plane, new_state); +#endif + return drm_gem_plane_helper_prepare_fb(plane, new_state); +} + + +static void lsdc_plane_cleanup_fb(struct drm_plane *plane, + struct drm_plane_state *old_state) +{ +#ifdef CONFIG_DRM_LSDC_VRAM_DRIVER + struct drm_device *ddev = plane->dev; + struct lsdc_device *ldev = to_lsdc(ddev); + + if (ldev->use_vram_helper) + return drm_gem_vram_plane_helper_cleanup_fb(plane, old_state); +#endif +} + +static const struct drm_plane_helper_funcs lsdc_primary_plane_helpers = { + .prepare_fb = lsdc_plane_prepare_fb, + .cleanup_fb = lsdc_plane_cleanup_fb, + .atomic_check = lsdc_primary_plane_atomic_check, + .atomic_update = lsdc_primary_plane_atomic_update, + .atomic_disable = lsdc_primary_plane_atomic_disable, +}; + + + +static int lsdc_cursor_atomic_check(struct drm_plane *plane, + struct drm_atomic_state *state) +{ + struct drm_plane_state *new_plane_state = drm_atomic_get_new_plane_state(state, plane); + struct drm_crtc *crtc = new_plane_state->crtc; + struct drm_framebuffer *fb = new_plane_state->fb; + struct drm_crtc_state *crtc_state; + int ret; + + /* no need for further checks if the plane is being disabled */ + if (!crtc || !fb) + return 0; + + if (!new_plane_state->visible) + return 0; + + crtc_state = drm_atomic_get_new_crtc_state(state, + new_plane_state->crtc); + + ret = drm_atomic_helper_check_plane_state(new_plane_state, + crtc_state, + DRM_PLANE_HELPER_NO_SCALING, + DRM_PLANE_HELPER_NO_SCALING, + true, + true); + if (ret) + return ret; + + if ((fb->width < LSDC_CURS_MIN_SIZE) || + (fb->height < LSDC_CURS_MIN_SIZE) || + (fb->width > LSDC_CURS_MAX_SIZE) || + (fb->height > LSDC_CURS_MAX_SIZE)) { + drm_err(plane->dev, "Invalid cursor size: %dx%d\n", + fb->width, fb->height); + return -EINVAL; + } + + return 0; +} + + +/* Update the location of the cursor */ +static void lsdc_cursor_update_location(struct lsdc_device *ldev, + struct drm_crtc *crtc) +{ + u32 val; + + val = lsdc_reg_read32(ldev, LSDC_CURSOR_CFG_REG); + + if ((val & CURSOR_FORMAT_MASK) == 0) + val |= CURSOR_FORMAT_ARGB8888; + + /* Update the location of the cursor */ + if (drm_crtc_index(crtc)) + val |= CURSOR_LOCATION_BIT; + + lsdc_reg_write32(ldev, LSDC_CURSOR_CFG_REG, val); +} + +/* update the position of the cursor */ +static void lsdc_cursor_update_position(struct lsdc_device *ldev, int x, int y) +{ + if (x < 0) + x = 0; + + if (y < 0) + y = 0; + + lsdc_reg_write32(ldev, LSDC_CURSOR_POSITION_REG, (y << 16) | x); +} + + +static void lsdc_cursor_atomic_update(struct drm_plane *plane, + struct drm_atomic_state *state) +{ + struct drm_device *ddev = plane->dev; + struct lsdc_device *ldev = to_lsdc(ddev); + struct drm_plane_state *new_plane_state = drm_atomic_get_new_plane_state(state, plane); + struct drm_plane_state *old_plane_state = drm_atomic_get_old_plane_state(state, plane); + struct drm_framebuffer *new_fb = new_plane_state->fb; + struct drm_framebuffer *old_fb = old_plane_state->fb; + + if (new_fb != old_fb) { + u64 cursor_addr; + + if (ldev->use_vram_helper) { +#ifdef CONFIG_DRM_LSDC_VRAM_DRIVER + s64 offset; + + offset = lsdc_get_vram_bo_offset(new_fb); + cursor_addr = ldev->vram_base + offset; + + drm_dbg_kms(ddev, "%s offset: %llx\n", + plane->name, offset); +#endif + } else { + struct drm_gem_cma_object *cursor_obj; + + cursor_obj = drm_fb_cma_get_gem_obj(new_fb, 0); + if (!cursor_obj) + return; + + cursor_addr = cursor_obj->paddr; + } + + lsdc_reg_write32(ldev, LSDC_CURSOR_ADDR_REG, cursor_addr); + } + + lsdc_cursor_update_position(ldev, new_plane_state->crtc_x, + new_plane_state->crtc_y); + + lsdc_cursor_update_location(ldev, new_plane_state->crtc); +} + + +static void lsdc_cursor_atomic_disable(struct drm_plane *plane, + struct drm_atomic_state *state) +{ + struct drm_device *ddev = plane->dev; + struct lsdc_device *ldev = to_lsdc(ddev); + struct drm_plane_state *old_plane_state; + struct drm_crtc *crtc; + + old_plane_state = drm_atomic_get_old_plane_state(state, plane); + + if (old_plane_state) + crtc = old_plane_state->crtc; + + lsdc_reg_write32(ldev, LSDC_CURSOR_CFG_REG, 0); + + drm_dbg_kms(ddev, "%s disable\n", plane->name); +} + + +static const struct drm_plane_helper_funcs lsdc_cursor_plane_helpers = { + .prepare_fb = lsdc_plane_prepare_fb, + .cleanup_fb = lsdc_plane_cleanup_fb, + .atomic_check = lsdc_cursor_atomic_check, + .atomic_update = lsdc_cursor_atomic_update, + .atomic_disable = lsdc_cursor_atomic_disable, +}; + + +static int lsdc_plane_get_default_zpos(enum drm_plane_type type) +{ + switch (type) { + case DRM_PLANE_TYPE_PRIMARY: + return 0; + case DRM_PLANE_TYPE_OVERLAY: + return 1; + case DRM_PLANE_TYPE_CURSOR: + return 7; + } + return 0; +} + + +static void lsdc_plane_reset(struct drm_plane *plane) +{ + drm_atomic_helper_plane_reset(plane); + + plane->state->zpos = lsdc_plane_get_default_zpos(plane->type); + + drm_dbg_kms(plane->dev, "%s reset\n", plane->name); +} + + +static const struct drm_plane_funcs lsdc_plane_funcs = { + .update_plane = drm_atomic_helper_update_plane, + .disable_plane = drm_atomic_helper_disable_plane, + .destroy = drm_plane_cleanup, + .reset = lsdc_plane_reset, + .atomic_duplicate_state = drm_atomic_helper_plane_duplicate_state, + .atomic_destroy_state = drm_atomic_helper_plane_destroy_state, +}; + + +int lsdc_plane_init(struct lsdc_device *ldev, struct drm_plane *plane, + enum drm_plane_type type, unsigned int index) +{ + struct drm_device *ddev = &ldev->drm; + int zpos = lsdc_plane_get_default_zpos(type); + unsigned int format_count; + const uint32_t *formats; + const char *name; + int ret; + + switch (type) { + case DRM_PLANE_TYPE_PRIMARY: + formats = lsdc_primary_formats; + format_count = ARRAY_SIZE(lsdc_primary_formats); + name = "primary-%u"; + break; + case DRM_PLANE_TYPE_CURSOR: + formats = lsdc_cursor_formats; + format_count = ARRAY_SIZE(lsdc_cursor_formats); + name = "cursor-%u"; + break; + case DRM_PLANE_TYPE_OVERLAY: + drm_err(ddev, "overlay plane is not supported\n"); + break; + } + + ret = drm_universal_plane_init(ddev, plane, 1 << index, + &lsdc_plane_funcs, + formats, format_count, + lsdc_fb_format_modifiers, + type, name, index); + if (ret) { + drm_err(ddev, "%s failed: %d\n", __func__, ret); + return ret; + } + + switch (type) { + case DRM_PLANE_TYPE_PRIMARY: + drm_plane_helper_add(plane, &lsdc_primary_plane_helpers); + drm_plane_create_zpos_property(plane, zpos, 0, 6); + if (ldev->dirty_update) + drm_plane_enable_fb_damage_clips(plane); + break; + case DRM_PLANE_TYPE_CURSOR: + drm_plane_helper_add(plane, &lsdc_cursor_plane_helpers); + drm_plane_create_zpos_immutable_property(plane, zpos); + break; + case DRM_PLANE_TYPE_OVERLAY: + drm_err(ddev, "overlay plane is not supported\n"); + break; + } + + drm_plane_create_alpha_property(plane); + + return 0; +} diff --git a/drivers/gpu/drm/lsdc/lsdc_pll.c b/drivers/gpu/drm/lsdc/lsdc_pll.c new file mode 100644 index 000000000000..fcf3728a9067 --- /dev/null +++ b/drivers/gpu/drm/lsdc/lsdc_pll.c @@ -0,0 +1,657 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2020 Loongson Corporation + * + * Permission is hereby granted, free of charge, to any person obtaining a + * copy of this software and associated documentation files (the + * "Software"), to deal in the Software without restriction, including + * without limitation the rights to use, copy, modify, merge, publish, + * distribute, sub license, and/or sell copies of the Software, and to + * permit persons to whom the Software is furnished to do so, subject to + * the following conditions: + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IN NO EVENT SHALL + * THE COPYRIGHT HOLDERS, AUTHORS AND/OR ITS SUPPLIERS BE LIABLE FOR ANY CLAIM, + * DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR + * OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE + * USE OR OTHER DEALINGS IN THE SOFTWARE. + * + * The above copyright notice and this permission notice (including the + * next paragraph) shall be included in all copies or substantial portions + * of the Software. + */ + +/* + * Authors: + * Sui Jingfeng suijingfeng@loongson.cn + */ + +#include <drm/drm_print.h> + +#include "lsdc_drv.h" +#include "lsdc_regs.h" +#include "lsdc_pll.h" + +/* device dependent pixpll regs */ + +/* u64 */ +struct ls7a1000_pixpll_bitmap { + /* Byte 0 ~ Byte 3 */ + unsigned div_out : 7; /* 0 : 6 output clock divider */ + unsigned reserved_1 : 14; /* 7 : 20 */ + unsigned loopc : 9; /* 21 : 29 */ + unsigned reserved_2 : 2; /* 30 : 31 */ + + /* Byte 4 ~ Byte 7 */ + unsigned div_ref : 7; /* 0 : 6 input clock divider */ + unsigned locked : 1; /* 7 PLL locked flag */ + unsigned sel_out : 1; /* 8 output clk selector */ + unsigned reserved_3 : 2; /* 9 : 10 reserved */ + unsigned set_param : 1; /* 11 set pll param */ + unsigned bypass : 1; /* 12 */ + unsigned powerdown : 1; /* 13 */ + unsigned reserved_4 : 18; /* 14 : 31 */ +}; + + +/* u128 */ +struct ls2k1000_pixpll_bitmap { + /* Byte 0 ~ Byte 3 */ + unsigned sel_out : 1; /* 0 select this PLL */ + unsigned reserved_1 : 1; /* 1 */ + unsigned sw_adj_en : 1; /* 2 allow software adjust */ + unsigned bypass : 1; /* 3 bypass L1 PLL */ + unsigned reserved_2 : 3; /* 4:6 */ + unsigned lock_en : 1; /* 7 enable lock L1 PLL */ + unsigned reserved_3 : 2; /* 8:9 */ + unsigned lock_check : 2; /* 10:11 precision check */ + unsigned reserved_4 : 4; /* 12:15 */ + + unsigned locked : 1; /* 16 PLL locked flag bit */ + unsigned reserved_5 : 2; /* 17:18 */ + unsigned powerdown : 1; /* 19 powerdown the pll if set */ + unsigned reserved_6 : 6; /* 20:25 */ + unsigned div_ref : 6; /* 26:31 L1 Prescaler */ + + /* Byte 4 ~ Byte 7 */ + unsigned loopc : 10; /* 32:41 Clock Multiplier */ + unsigned l1_div : 6; /* 42:47 not used */ + unsigned reserved_7 : 16; /* 48:63 */ + + /* Byte 8 ~ Byte 15 */ + unsigned div_out : 6; /* 0 : 5 output clock divider */ + unsigned reserved_8 : 26; /* 6 : 31 */ + unsigned reserved_9 : 32; /* 70: 127 */ +}; + + +/* u32 */ +struct ls2k0500_pixpll_bitmap { + /* Byte 0 ~ Byte 1 */ + unsigned sel_out : 1; + unsigned reserved_1 : 2; + unsigned sw_adj_en : 1; /* allow software adjust */ + unsigned bypass : 1; /* bypass L1 PLL */ + unsigned powerdown : 1; /* write 1 to powerdown the PLL */ + unsigned reserved_2 : 1; + unsigned locked : 1; /* 7 Is L1 PLL locked, read only */ + unsigned div_ref : 6; /* 8:13 ref clock divider */ + unsigned reserved_3 : 2; /* 14:15 */ + /* Byte 2 ~ Byte 3 */ + unsigned loopc : 8; /* 16:23 Clock Multiplier */ + unsigned div_out : 6; /* 24:29 output clock divider */ + unsigned reserved_4 : 2; /* 30:31 */ +}; + + +/* + * NOTE: All loongson's cpu is little endian. + */ +union lsdc_pix_pll_param { + struct ls7a1000_pixpll_bitmap ls7a1000; + struct ls2k1000_pixpll_bitmap ls2k1000; + struct ls2k0500_pixpll_bitmap ls2k0500; + + u32 dword[4]; +}; + +/* + * pixel clock to pll parameters translation table + */ +struct pixclk_to_pll_parm { + /* kHz */ + unsigned int clock; + + /* unrelated information */ + unsigned short width; + unsigned short height; + unsigned short vrefresh; + + /* Stores parameters for programming the Hardware PLLs */ + unsigned short div_out; + unsigned short loopc; + unsigned short div_ref; +}; + + +/* + * Small cached value to speed up pll parameter calculation + */ +static const struct pixclk_to_pll_parm pll_param_table[] = { + {148500, 1920, 1080, 60, 11, 49, 3}, /* 1920x1080@60Hz */ + /* 1920x1080@50Hz */ + {174500, 1920, 1080, 75, 17, 89, 3}, /* 1920x1080@75Hz */ + {181250, 2560, 1080, 75, 8, 58, 4}, /* 2560x1080@75Hz */ + {146250, 1680, 1050, 60, 16, 117, 5}, /* 1680x1050@60Hz */ + {135000, 1280, 1024, 75, 10, 54, 4}, /* 1280x1024@75Hz */ + + {108000, 1600, 900, 60, 15, 81, 5}, /* 1600x900@60Hz */ + /* 1280x1024@60Hz */ + /* 1280x960@60Hz */ + /* 1152x864@75Hz */ + + {106500, 1440, 900, 60, 19, 81, 4}, /* 1440x900@60Hz */ + {88750, 1440, 900, 60, 16, 71, 5}, /* 1440x900@60Hz */ + {83500, 1280, 800, 60, 17, 71, 5}, /* 1280x800@60Hz */ + {71000, 1280, 800, 60, 20, 71, 5}, /* 1280x800@60Hz */ + + {74250, 1280, 720, 60, 22, 49, 3}, /* 1280x720@60Hz */ + /* 1280x720@50Hz */ + + {78750, 1024, 768, 75, 16, 63, 5}, /* 1024x768@75Hz */ + {75000, 1024, 768, 70, 29, 87, 4}, /* 1024x768@70Hz */ + {65000, 1024, 768, 60, 20, 39, 3}, /* 1024x768@60Hz */ + + {51200, 1024, 600, 60, 25, 64, 5}, /* 1024x600@60Hz */ + + {57284, 832, 624, 75, 24, 55, 4}, /* 832x624@75Hz */ + {49500, 800, 600, 75, 40, 99, 5}, /* 800x600@75Hz */ + {50000, 800, 600, 72, 44, 88, 4}, /* 800x600@72Hz */ + {40000, 800, 600, 60, 30, 36, 3}, /* 800x600@60Hz */ + {36000, 800, 600, 56, 50, 72, 4}, /* 800x600@56Hz */ + {31500, 640, 480, 75, 40, 63, 5}, /* 640x480@75Hz */ + /* 640x480@73Hz */ + + {30240, 640, 480, 67, 62, 75, 4}, /* 640x480@67Hz */ + {27000, 720, 576, 50, 50, 54, 4}, /* 720x576@60Hz */ + {25175, 640, 480, 60, 85, 107, 5}, /* 640x480@60Hz */ + {25200, 640, 480, 60, 50, 63, 5}, /* 640x480@60Hz */ + /* 720x480@60Hz */ +}; + +/** + * lsdc_pixpll_setup + * + * @this: point to the object which calling this function + * + * ioremap the device dependent register before using it + */ +static int lsdc_pixpll_setup(struct lsdc_pll * const this) +{ + this->mmio = ioremap(this->reg_base, this->reg_size); + + drm_info(this->ddev, "PIXPLL%u REG[%x, %u] map to %llx\n", + this->index, this->reg_base, this->reg_size, (u64)this->mmio); + + return 0; +} + + + +/* + * Find a set of pll parameters (to generate pixel clock) from a static + * local table, which avoid to compute the pll parameter everytime a + * modeset is triggered. + * + * @this: point to the object which calling this function + * @clock: the desired pixel clock wanted to generate, the unit is kHz + * @pout: pointer to where hardware pll parameters(if found) to save + * + * Return true if a parameter is found, otherwise return false. + */ +static bool lsdc_pixpll_find(struct lsdc_pll * const this, + unsigned int clock, + struct lsdc_pll_core_values * const pout) +{ + unsigned int num = ARRAY_SIZE(pll_param_table); + unsigned int i; + + for (i = 0; i < num; i++) { + if (clock != pll_param_table[i].clock) + continue; + + pout->div_ref = pll_param_table[i].div_ref; + pout->loopc = pll_param_table[i].loopc; + pout->div_out = pll_param_table[i].div_out; + + return true; + } + + drm_dbg(this->ddev, "pixel clock %u: miss\n", clock); + + return false; +} + +/* + * Find a set of pll parameters which have minimal difference with desired + * clock frequency. It does that by computing the all of pll parameters + * combines possible and compare the diff and find the minimal. + * + * clock_out = refclk / div_ref * loopc / div_out + * + * refclk is fixed as 100MHz in ls7a1000, ls2k1000 and ls2k0500 + * + * @this: point to the object which calling this function + * @clk: the desired pixel clock wanted to generate, the unit is kHz + * @verbose: print the pll parameter and the actual pixel clock. + * @pout: pointer to where hardware pll parameters(if found) to save + * + * Return true if a parameter is found, otherwise return false. + */ +static bool lsdc_pixpll_compute(struct lsdc_pll * const this, + unsigned int clk, + bool verbose, + struct lsdc_pll_core_values * const pout) +{ + unsigned int refclk = this->ref_clock; + const unsigned int tolerance = 1000; + unsigned int min = tolerance; + unsigned int div_out, loopc, div_ref; + + if (lsdc_pixpll_find(this, clk, pout)) + return true; + + for (div_out = 6; div_out < 64; div_out++) { + for (div_ref = 3; div_ref < 6; div_ref++) { + for (loopc = 6; loopc < 161; loopc++) { + int diff; + + if (loopc < 12 * div_ref) + continue; + if (loopc > 32 * div_ref) + continue; + + diff = clk * div_out - refclk * loopc / div_ref; + + if (diff < 0) + diff = -diff; + + if (diff < min) { + min = diff; + pout->div_ref = div_ref; + pout->div_out = div_out; + pout->loopc = loopc; + + if (diff == 0) + return true; + } + } + } + } + + if (verbose) { + unsigned int clk_out; + + clk_out = refclk / pout->div_ref * pout->loopc / pout->div_out; + + drm_info(this->ddev, "pixpll%u\n", this->index); + + drm_info(this->ddev, "div_ref=%u, loopc=%u, div_out=%u\n", + pout->div_ref, pout->loopc, pout->div_out); + + drm_info(this->ddev, "desired clk=%u, actual out=%u, diff=%d\n", + clk, clk_out, clk_out - clk); + } + + return min < tolerance; +} + +/* + * Update the pll parameters to hardware, target to the pixpll in ls7a1000 + * + * @this: point to the object which calling this function + * @param: pointer to where the parameters passed in + * + * Return true if a parameter is found, otherwise return false. + */ +static int ls7a1000_pixpll_param_update(struct lsdc_pll * const this, + const struct lsdc_pll_core_values * const param) +{ + u32 val; + unsigned int counter = 0; + void __iomem *reg = this->mmio; + bool locked; + + + /* clear sel_pll_out0 */ + val = readl(reg + 0x4); + val &= ~(1 << 8); + writel(val, reg + 0x4); + + /* set pll_pd */ + val = readl(reg + 0x4); + val |= (1 << 13); + writel(val, reg + 0x4); + + /* clear set_pll_param */ + val = readl(reg + 0x4); + val &= ~(1 << 11); + writel(val, reg + 0x4); + + /* clear old value & config new value */ + val = readl(reg + 0x04); + val &= ~0x7F; + + val |= param->div_ref; /* div_ref */ + writel(val, reg + 0x4); + + val = readl(reg); + val &= ~(0x7f << 0); + val |= param->div_out; /* div_out */ + val &= ~(0x1ffUL << 21); + val |= param->loopc << 21; /* loopc */ + writel(val, reg); + + /* set set_pll_param */ + val = readl(reg + 0x4); + val |= (1 << 11); + writel(val, reg + 0x4); + + /* clear pll_pd */ + val = readl(reg + 0x4); + val &= ~(1 << 13); + writel(val, reg + 0x4); + + /* wait pll lock */ + do { + val = readl(reg + 0x4); + locked = val & 0x80; + counter++; + } while (locked == false); + + drm_dbg_kms(this->ddev, "%u loop waited\n", counter); + + /* set sel_pll_out0 */ + val = readl(reg + 0x4); + val |= (1UL << 8); + writel(val, reg + 0x4); + + return 0; +} + + +/* + * Update the pll parameters to hardware, target to the pixpll in ls2k1000 + * + * @this: point to the object which calling this function + * @param: pointer to where the parameters passed in + * + * Return true if a parameter is found, otherwise return false. + */ +static int ls2k1000_pixpll_param_update(struct lsdc_pll * const this, + const struct lsdc_pll_core_values * const param) +{ + void __iomem *reg = this->mmio; + unsigned int counter = 0; + bool locked = false; + u32 val; + + val = readl(reg); + /* Bypass the software configured PLL, using refclk directly */ + val &= ~(1 << 0); + writel(val, reg); + + /* powerdown the PLL */ + val |= (1 << 19); + writel(val, reg); + + /* Allow the software configuration */ + val &= ~(1 << 2); + writel(val, reg); + + /* allow L1 PLL lock */ + val = (1L << 7) | (3L << 10); + writel(val, reg); + + /* clear div_ref bit field */ + val &= ~(0x3f << 26); + /* set div_ref bit field */ + val = val | (param->div_ref << 26); + writel(val, reg); + + val = readl(reg + 4); + /* clear loopc bit field */ + val &= ~0x0fff; + /* set loopc bit field */ + val |= param->loopc; + writel(val, reg + 4); + + /* set div_out */ + writel(param->div_out, reg + 8); + + val = readl(reg); + /* use the software configure param */ + val |= (1 << 2); + /* powerup the PLL */ + val &= ~(1 << 19); + writel(val, reg); + + /* wait pll setup and locked */ + do { + val = readl(reg); + locked = val & 0x10000; + counter++; + } while (locked == false); + + drm_dbg_kms(this->ddev, "%u loop waited\n", counter); + + /* Switch to the above software configured PLL instead of refclk */ + val |= 1; + writel(val, reg); + + return 0; +} + +/* + * Update the pll parameters to hardware, target to the pixpll in ls2k0500 + * + * @this: point to the object which calling this function + * @param: pointer to where the parameters passed in + * + * Return true if a parameter is found, otherwise return false. + */ + +static int ls2k0500_pixpll_param_update(struct lsdc_pll * const this, + const struct lsdc_pll_core_values * const param) +{ + void __iomem *reg = this->mmio; + unsigned int counter = 0; + bool locked = false; + u32 val; + + /* Bypass the software configured PLL, using refclk directly */ + val = readl(reg); + val &= ~(1 << 0); + writel(val, reg); + + /* Powerdown the PLL */ + val = readl(reg); + val |= (1 << 5); + writel(val, reg); + + /* Allow the software configuration */ + val |= (1 << 3); + writel(val, reg); + + /* Update the pll params */ + val = (param->div_out << 24) | + (param->loopc << 16) | + (param->div_ref << 8); + + writel(val, reg); + + /* Powerup the PLL */ + val = readl(reg); + val &= ~(1 << 5); + writel(val, reg); + + /* wait pll setup and locked */ + do { + val = readl(reg); + locked = val & 0x80; + counter++; + } while (locked == false); + + drm_dbg_kms(this->ddev, "%u loop waited\n", counter); + + /* Switch to the above software configured PLL instead of refclk */ + writel((val | 1), reg); + + return 0; +} + + +#define LSDC_PIXPLL_BITMAP(type,var,parms) \ + struct type ## _pixpll_bitmap *var = &parms.type + +#define LSDC_PIXPLL_PRINT_CODE_BLOCK(ddev,var,index,refclk) \ +{ \ + out_clk = refclk / var->div_ref * var->loopc / var->div_out; \ + drm_info(ddev, "div_ref=%u, loopc=%u, div_out=%u\n", \ + var->div_ref, var->loopc, var->div_out); \ + drm_info(ddev, "locked: %s\n", var->locked ? "Yes" : "No"); \ + drm_info(ddev, "bypass: %s\n", var->bypass ? "Yes" : "No"); \ + drm_info(ddev, "powerdown: %s\n", var->powerdown ? "Yes" : "No"); \ + drm_info(ddev, "set_out: %s\n", var->sel_out ? "Yes" : "No"); \ + drm_info(ddev, "pixpll%u generate %ukHz\n", index, out_clk); \ + drm_info(ddev, "\n"); \ +} + +/* lsdc_print_clock - print clock related parameters + * + * clock_out = refclk / div_ref * loopc / divout + * + * also print the precision information + */ +static void lsdc_pixpll_print(struct lsdc_pll * const this, unsigned int pixclk) +{ + struct drm_device *ddev = this->ddev; + struct lsdc_device *ldev = to_lsdc(ddev); + const struct lsdc_chip_desc * const desc = ldev->desc; + unsigned short index = this->index; + unsigned int refclk = this->ref_clock; + unsigned int out_clk; + union lsdc_pix_pll_param parms; + + if (desc->chip == LSDC_CHIP_7A1000) { + LSDC_PIXPLL_BITMAP(ls7a1000, obj, parms); + parms.dword[0] = readl(this->mmio); + parms.dword[1] = readl(this->mmio + 4); + LSDC_PIXPLL_PRINT_CODE_BLOCK(ddev, obj, index, refclk); + } else if (desc->chip == LSDC_CHIP_2K1000) { + LSDC_PIXPLL_BITMAP(ls2k1000, obj, parms); + parms.dword[0] = readl(this->mmio); + parms.dword[1] = readl(this->mmio + 4); + parms.dword[2] = readl(this->mmio + 8); + parms.dword[3] = readl(this->mmio + 12); + LSDC_PIXPLL_PRINT_CODE_BLOCK(ddev, obj, index, refclk); + } else if (desc->chip == LSDC_CHIP_2K0500) { + LSDC_PIXPLL_BITMAP(ls2k0500, obj, parms); + parms.dword[0] = readl(this->mmio); + LSDC_PIXPLL_PRINT_CODE_BLOCK(ddev, obj, index, refclk); + } else { + drm_err(ddev, "unknown chip, the driver need update\n"); + return; + } +} + + +static unsigned int lsdc_get_clock_rate(struct lsdc_pll * const this) +{ + struct lsdc_pll_core_values * const parms = &this->core_params; + unsigned int clk_out = this->ref_clock / parms->div_ref; + + clk_out = clk_out * parms->loopc / parms->div_out; + + return clk_out; +} + + +static const struct lsdc_pixpll_funcs ls7a1000_pixpll_funcs = { + .setup = lsdc_pixpll_setup, + .compute = lsdc_pixpll_compute, + .update = ls7a1000_pixpll_param_update, + .get_clock_rate = lsdc_get_clock_rate, + + .print = lsdc_pixpll_print, +}; + +static const struct lsdc_pixpll_funcs ls2k1000_pixpll_funcs = { + .setup = lsdc_pixpll_setup, + .compute = lsdc_pixpll_compute, + .update = ls2k1000_pixpll_param_update, + .get_clock_rate = lsdc_get_clock_rate, + + .print = lsdc_pixpll_print, +}; + +static const struct lsdc_pixpll_funcs ls2k0500_pixpll_funcs = { + .setup = lsdc_pixpll_setup, + .compute = lsdc_pixpll_compute, + .update = ls2k0500_pixpll_param_update, + .get_clock_rate = lsdc_get_clock_rate, + + .print = lsdc_pixpll_print, +}; + + +int lsdc_pixpll_init(struct lsdc_pll * const this, + struct drm_device *ddev, + unsigned int index) +{ + struct lsdc_device *ldev = to_lsdc(ddev); + const struct lsdc_chip_desc *ip = ldev->desc; + + this->ddev = ddev; + this->index = index; + this->ref_clock = LSDC_PLL_REF_CLK; + + if (ip->chip == LSDC_CHIP_7A1000) { + if (index == 0) + this->reg_base = LS7A1000_CFG_REG_BASE + + LS7A1000_PIX_PLL0_REG; + else if (index == 1) + this->reg_base = LS7A1000_CFG_REG_BASE + + LS7A1000_PIX_PLL1_REG; + this->reg_size = 8; + this->funcs = &ls7a1000_pixpll_funcs; + } else if (ip->chip == LSDC_CHIP_2K1000) { + if (index == 0) + this->reg_base = LS2K1000_CFG_REG_BASE + + LS2K1000_PIX_PLL0_REG; + else if (index == 1) + this->reg_base = LS2K1000_CFG_REG_BASE + + LS2K1000_PIX_PLL1_REG; + + this->reg_size = 16; + this->funcs = &ls2k1000_pixpll_funcs; + } else if (ip->chip == LSDC_CHIP_2K0500) { + if (index == 0) + this->reg_base = LS2K0500_CFG_REG_BASE + + LS2K0500_PIX_PLL0_REG; + else if (index == 1) + this->reg_base = LS2K0500_CFG_REG_BASE + + LS2K0500_PIX_PLL1_REG; + + this->reg_size = 4; + this->funcs = &ls2k0500_pixpll_funcs; + } else { + DRM_ERROR("unknown chip, the driver need update\n"); + return -ENOENT; + } + + /* call funcs->init only once */ + return this->funcs->setup(this); +} diff --git a/drivers/gpu/drm/lsdc/lsdc_pll.h b/drivers/gpu/drm/lsdc/lsdc_pll.h new file mode 100644 index 000000000000..ea44646b91ba --- /dev/null +++ b/drivers/gpu/drm/lsdc/lsdc_pll.h @@ -0,0 +1,109 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright (C) 2020 Loongson Corporation + * + * Permission is hereby granted, free of charge, to any person obtaining a + * copy of this software and associated documentation files (the + * "Software"), to deal in the Software without restriction, including + * without limitation the rights to use, copy, modify, merge, publish, + * distribute, sub license, and/or sell copies of the Software, and to + * permit persons to whom the Software is furnished to do so, subject to + * the following conditions: + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IN NO EVENT SHALL + * THE COPYRIGHT HOLDERS, AUTHORS AND/OR ITS SUPPLIERS BE LIABLE FOR ANY CLAIM, + * DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR + * OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE + * USE OR OTHER DEALINGS IN THE SOFTWARE. + * + * The above copyright notice and this permission notice (including the + * next paragraph) shall be included in all copies or substantial portions + * of the Software. + */ + +/* + * Authors: + * Sui Jingfeng suijingfeng@loongson.cn + */ + +#ifndef __LSDC_PLL_H__ +#define __LSDC_PLL_H__ + +#include <drm/drm_device.h> + +/* + * PIXEL PLL structure + * + * refclk: reference frequency, 100 MHz from external oscillator + * outclk: output frequency desired. + * + * + * L1 Fref Fvco L2 + * refclk +-----------+ +------------------+ +---------+ outclk + * -------> | Prescaler | ---> | Clock Multiplier | ---> | divider | ---------> + * | +-----------+ +------------------+ +---------+ ^ + * | ^ ^ ^ | + * | | | | | + * | | | | | + * | div_ref loopc div_out | + * | | + * +------------- sel_out (=1 => bypass above clock) -----------------+ + * + * + * outclk = refclk / div_ref * loopc / div_out; + * + * PLL hardware working requirements: + * + * 1) 20 MHz <= refclk / div_ref <= 40Mhz + * 2) 1.2 GHz <= refclk /div_out * loopc <= 3.2 Ghz + * + */ + +struct lsdc_pll_core_values { + unsigned int div_ref; + unsigned int loopc; + unsigned int div_out; +}; + +struct lsdc_pll; + +struct lsdc_pixpll_funcs { + int (*setup)(struct lsdc_pll * const this); + bool (*compute)(struct lsdc_pll * const this, + unsigned int clock, + bool verbose, + struct lsdc_pll_core_values * const params_out); + int (*update)(struct lsdc_pll * const this, + const struct lsdc_pll_core_values * const params_in); + + void (*print)(struct lsdc_pll * const this, unsigned int clock); + + unsigned int (*get_clock_rate)(struct lsdc_pll * const this); +}; + + +struct lsdc_pll { + const struct lsdc_pixpll_funcs *funcs; + struct drm_device *ddev; + void __iomem *mmio; + + /* Reg offset of the PLL */ + u32 reg_base; + u32 reg_size; + + struct lsdc_pll_core_values core_params; + + /* Stores parameters for programming the PLLs */ + unsigned int ref_clock; /* 100000kHz, fixed */ + + unsigned short index; +}; + + +int lsdc_pixpll_init(struct lsdc_pll * const this, + struct drm_device *ddev, + unsigned int index); + +#endif diff --git a/drivers/gpu/drm/lsdc/lsdc_regs.h b/drivers/gpu/drm/lsdc/lsdc_regs.h new file mode 100644 index 000000000000..804e476a2e7a --- /dev/null +++ b/drivers/gpu/drm/lsdc/lsdc_regs.h @@ -0,0 +1,246 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright (C) 2020 Loongson Corporation + * + * Permission is hereby granted, free of charge, to any person obtaining a + * copy of this software and associated documentation files (the + * "Software"), to deal in the Software without restriction, including + * without limitation the rights to use, copy, modify, merge, publish, + * distribute, sub license, and/or sell copies of the Software, and to + * permit persons to whom the Software is furnished to do so, subject to + * the following conditions: + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IN NO EVENT SHALL + * THE COPYRIGHT HOLDERS, AUTHORS AND/OR ITS SUPPLIERS BE LIABLE FOR ANY CLAIM, + * DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR + * OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE + * USE OR OTHER DEALINGS IN THE SOFTWARE. + * + * The above copyright notice and this permission notice (including the + * next paragraph) shall be included in all copies or substantial portions + * of the Software. + */ + +/* + * Authors: + * Sui Jingfeng suijingfeng@loongson.cn + */ + +#ifndef __LSDC_REGS_H__ +#define __LSDC_REGS_H__ + +#include <linux/bitops.h> +#include <linux/types.h> + +/* + * PLL + */ +#define LSDC_PLL_REF_CLK 100000 /* kHz */ +#define PCLK_PRECISION_INDICATOR 10000 + + +/* + * Those PLL registers is not in dc's bar space, + * there are relative to LSXXXXX_CFG_REG_BASE. + * XXXXX = 7A1000, 2K1000, 2K0500 + */ + +/* LS2K1000 */ +#define LS2K1000_DC_PLL_REG 0x04A0 + +#define LS2K1000_PIX_PLL0_REG 0x04B0 +#define LS2K1000_PIX_PLL1_REG 0x04C0 + +#define LS2K1000_CFG_REG_BASE 0x1fe10000 + +/* LS7A1000 */ +#define LS7A1000_DC_PLL_REG 0x0490 + +#define LS7A1000_PIX_PLL0_REG 0x04B0 +#define LS7A1000_PIX_PLL1_REG 0x04C0 + +#define LS7A1000_CFG_REG_BASE 0x10010000 + +/* LS2K0500 */ +#define LS2K0500_PIX_PLL0_REG 0x0418 +#define LS2K0500_PIX_PLL1_REG 0x0420 + +#define LS2K0500_CFG_REG_BASE 0x1fe10000 + + +/* + * CRTC CFG REG + */ +#define CFG_PIX_FMT_MASK 0x07 + + +#define CFG_PAGE_FLIP_BIT BIT(7) /* triger pageflip */ +#define CFG_OUTPUT_EN_BIT BIT(8) +#define CFG_PANEL_SWITCH BIT(9) +/* Indicate witch framebuffer addr reg is in using */ +#define CFG_FB_IDX_BIT BIT(11) +#define CFG_GAMMAR_EN_BIT BIT(12) +#define CFG_DC_DMA_MASK GENMASK(17, 16) + +/* crtc get soft reset if voltage level change from 1 -> 0 */ +#define CFG_RESET_BIT BIT(20) + +#define EN_HSYNC_BIT BIT(30) +#define INV_HSYNC_BIT BIT(31) + +#define EN_VSYNC_BIT BIT(30) +#define INV_VSYNC_BIT BIT(31) + + +/******** CRTC0 & DVO0 ********/ + +#define LSDC_CRTC0_CFG_REG 0x1240 + +#define LSDC_CRTC0_FB_ADDR0_REG 0x1260 +#define LSDC_CRTC0_FB_ADDR1_REG 0x1580 + +#define LSDC_CRTC0_STRIDE_REG 0x1280 +#define LSDC_CRTC0_FB_ORIGIN_REG 0x1300 +#define LSDC_CRTC0_HDISPLAY_REG 0x1400 +#define LSDC_CRTC0_HSYNC_REG 0x1420 +#define LSDC_CRTC0_VDISPLAY_REG 0x1480 +#define LSDC_CRTC0_VSYNC_REG 0x14a0 + + +/******** CTRC1 & DVO1 ********/ + +#define LSDC_CRTC1_CFG_REG 0x1250 + +#define LSDC_CRTC1_FB_ADDR0_REG 0x1270 +#define LSDC_CRTC1_FB_ADDR1_REG 0x1590 + +#define LSDC_CRTC1_STRIDE_REG 0x1290 +#define LSDC_CRTC1_FB_ORIGIN_REG 0x1310 +#define LSDC_CRTC1_HDISPLAY_REG 0x1410 +#define LSDC_CRTC1_HSYNC_REG 0x1430 +#define LSDC_CRTC1_VDISPLAY_REG 0x1490 +#define LSDC_CRTC1_VSYNC_REG 0x14b0 + + +/* + * Hardware cursor + * There is only one hardware cursor shared by two crtc in ls7a1000, + * ls2k1000 and ls2k0500, but ls7a2000 have two Hardware cursor. + */ +#define LSDC_CURSOR_CFG_REG 0x1520 + +#define CURSOR_FORMAT_MASK 0x03 +#define CURSOR_FORMAT_DISABLE 0 +#define CURSOR_FORMAT_MONOCHROME BIT(0) +#define CURSOR_FORMAT_ARGB8888 BIT(1) +#define CURSOR_LOCATION_BIT BIT(4) + +#define LSDC_CURSOR_ADDR_REG 0x1530 +#define LSDC_CURSOR_POSITION_REG 0x1540 +#define LSDC_CURSOR_BG_COLOR_REG 0x1550 /* background color */ +#define LSDC_CURSOR_FG_COLOR_REG 0x1560 /* foreground color */ + +#define CUR_WIDTH_SIZE 32 +#define CUR_HEIGHT_SIZE 32 + +#define LSDC_CURS_MIN_SIZE 1 +#define LSDC_CURS_MAX_SIZE 64 + +/* + * DC Interrupt Control Register, 32bit, Address Offset: 1570 + * + * Bits 0:10 inidicate the interrupt type, read only + * Bits 16:26 control if the specific interrupt corresponding to bit 0~10 + * is enabled or not. Write 1 to enable, write 0 to disable + * + * RF: Read Finished + * IDBU : Internal Data Buffer Underflow + * IDBFU : Internal Data Buffer Fatal Underflow + * + * + * +-------+-------------------------------+-------+--------+--------+-------+ + * | 31:27 | 26:16 | 15:11 | 10 | 9 | 8 | + * +-------+-------------------------------+-------+--------+--------+-------+ + * | N/A | Interrupt Enable Control Bits | N/A | IDBFU0 | IDBFU1 | IDBU0 | + * +-------+-------------------------------+-------+--------+--------+-------+ + * + * Bit 4 is cursor buffer read finished, no use. + * + * +-------+-----+-----+-----+--------+--------+--------+--------+ + * | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | + * +-------+-----+-----+-----+--------+--------+--------+--------+ + * | IDBU1 | RF0 | RF1 | | HSYNC0 | VSYNC0 | HSYNC1 | VSYNC1 | + * +-------+-----+-----+-----+--------+--------+--------+--------+ + * + */ + +#define LSDC_INT_REG 0x1570 + +#define INT_CRTC0_VS BIT(2) +#define INT_CRTC0_HS BIT(3) +#define INT_CRTC0_RF BIT(6) +#define INT_CRTC0_IDBU BIT(8) +#define INT_CRTC0_IDBFU BIT(10) + +#define INT_CURSOR_RF BIT(4) + +#define INT_CRTC1_VS BIT(0) +#define INT_CRTC1_HS BIT(1) +#define INT_CRTC1_RF BIT(5) +#define INT_CRTC1_IDBU BIT(7) +#define INT_CRTC1_IDBFU BIT(9) + + +#define INT_CRTC0_VS_EN BIT(18) +#define INT_CRTC0_HS_EN BIT(19) +#define INT_CRTC0_RF_EN BIT(22) +#define INT_CRTC0_IDBU_EN BIT(24) +#define INT_CRTC0_IDBFU_EN BIT(26) + +#define INT_CURSOR_RF_EN BIT(20) + +#define INT_CRTC1_VS_EN BIT(16) +#define INT_CRTC1_HS_EN BIT(17) +#define INT_CRTC1_RF_EN BIT(21) +#define INT_CRTC1_IDBU_EN BIT(23) +#define INT_CRTC1_IDBFU_EN BIT(25) + + +#define INT_STATUS_MASK GENMASK(10, 0) + + +/* + * LS7A1000 have 4 gpio which is under control of the LS7A_DC_GPIO_DAT_REG + * and LS7A_DC_GPIO_DIR_REG register, it has no relationship whth the general + * GPIO hardware as those two registers are in the DC register space on + * LS7A1000. + * + * This driver using those GPIO to emulated I2C, for reading edid and + * monitor detection + * + * LS2k1000 and LS2K0500 don't have those registers, they use hardware i2c or + * generial GPIO emulated i2c from other module. + * + * GPIO data register + * Address offset: 0x1650 + * +---------------+-----------+-----------+ + * | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | + * +---------------+-----------+-----------+ + * | | DVO1 | DVO0 | + * + N/A +-----------+-----------+ + * | | SCL | SDA | SCL | SDA | + * +---------------+-----------+-----------+ + */ +#define LS7A_DC_GPIO_DAT_REG 0x1650 + +/* + * GPIO Input/Output direction control register + * Address offset: 0x1660 + * write 1 for Input, 0 for Output. + */ +#define LS7A_DC_GPIO_DIR_REG 0x1660 + + +#endif
From: suijingfeng suijingfeng@loongson.cn
The display controller is a pci device, its vendor id is 0x0014 its device id is 0x7a06.
Signed-off-by: suijingfeng suijingfeng@loongson.cn Signed-off-by: Sui Jingfeng 15330273260@189.cn --- arch/mips/boot/dts/loongson/loongson64-2k1000.dtsi | 11 +++++++++++ 1 file changed, 11 insertions(+)
diff --git a/arch/mips/boot/dts/loongson/loongson64-2k1000.dtsi b/arch/mips/boot/dts/loongson/loongson64-2k1000.dtsi index 8143a61111e3..6510b0e6928a 100644 --- a/arch/mips/boot/dts/loongson/loongson64-2k1000.dtsi +++ b/arch/mips/boot/dts/loongson/loongson64-2k1000.dtsi @@ -198,6 +198,17 @@ interrupt-parent = <&liointc0>; };
+ lsdc: dc@6,0 { + compatible = "pci0014,7a06.0", + "pci0014,7a06", + "pciclass030000", + "pciclass0300"; + + reg = <0x3000 0x0 0x0 0x0 0x0>; + interrupts = <28 IRQ_TYPE_LEVEL_LOW>; + interrupt-parent = <&liointc0>; + }; + pci_bridge@9,0 { compatible = "pci0014,7a19.0", "pci0014,7a19",
From: suijingfeng suijingfeng@loongson.cn
For board specific devices which is outside of the cpu and bridge chip. this patch introduce two dts, one for lemote a1901(aka LX-6901) motherboard. documnet can be found from [1]. Another one is loongson 3A4000 evb board, this board have a vga and dvi interface.
We need introduce board specific dts because of we need the device tree to tell how does the connectors and encoders are connected to the DVO port of the display controller.
[1] https://wiki.godson.ac.cn/device:lemote_a1901
Signed-off-by: suijingfeng suijingfeng@loongson.cn Signed-off-by: Sui Jingfeng 15330273260@189.cn --- arch/mips/boot/dts/loongson/lemote_a1901.dts | 64 +++++++++++++++++ .../boot/dts/loongson/ls3a4000_7a1000_evb.dts | 68 +++++++++++++++++++ arch/mips/boot/dts/loongson/ls7a-pch.dtsi | 2 +- 3 files changed, 133 insertions(+), 1 deletion(-) create mode 100644 arch/mips/boot/dts/loongson/lemote_a1901.dts create mode 100644 arch/mips/boot/dts/loongson/ls3a4000_7a1000_evb.dts
diff --git a/arch/mips/boot/dts/loongson/lemote_a1901.dts b/arch/mips/boot/dts/loongson/lemote_a1901.dts new file mode 100644 index 000000000000..81828945ba52 --- /dev/null +++ b/arch/mips/boot/dts/loongson/lemote_a1901.dts @@ -0,0 +1,64 @@ +// SPDX-License-Identifier: GPL-2.0 + +/dts-v1/; + +#include "loongson64g-package.dtsi" +#include "ls7a-pch.dtsi" + +/ { + compatible = "lemode,a1901", "loongson,loongson64g-4core-ls7a"; + model = "lemode,a1901"; +}; + +&package0 { + htvec: interrupt-controller@efdfb000080 { + compatible = "loongson,htvec-1.0"; + reg = <0xefd 0xfb000080 0x40>; + interrupt-controller; + #interrupt-cells = <1>; + + interrupt-parent = <&liointc>; + interrupts = <24 IRQ_TYPE_LEVEL_HIGH>, + <25 IRQ_TYPE_LEVEL_HIGH>, + <26 IRQ_TYPE_LEVEL_HIGH>, + <27 IRQ_TYPE_LEVEL_HIGH>, + <28 IRQ_TYPE_LEVEL_HIGH>, + <29 IRQ_TYPE_LEVEL_HIGH>, + <30 IRQ_TYPE_LEVEL_HIGH>, + <31 IRQ_TYPE_LEVEL_HIGH>; + }; +}; + +&pch { + msi: msi-controller@2ff00000 { + compatible = "loongson,pch-msi-1.0"; + reg = <0 0x2ff00000 0 0x8>; + interrupt-controller; + msi-controller; + loongson,msi-base-vec = <64>; + loongson,msi-num-vecs = <192>; + interrupt-parent = <&htvec>; + }; +}; + +&lsdc { + /* use_vram_helper; */ + output-ports = <&dvo0 &dvo1>; + + #address-cells = <1>; + #size-cells = <0>; + + dvo0: dvo@0 { + /* 0 for DVO0 */ + reg = <0>; + status = "disabled"; + }; + + dvo1: dvo@1 { + /* 1 for DVO1 */ + reg = <1>; + connector = "vga-connector"; + encoder = "adi,adv7125"; + status = "okay"; + }; +}; diff --git a/arch/mips/boot/dts/loongson/ls3a4000_7a1000_evb.dts b/arch/mips/boot/dts/loongson/ls3a4000_7a1000_evb.dts new file mode 100644 index 000000000000..ff07f529ea43 --- /dev/null +++ b/arch/mips/boot/dts/loongson/ls3a4000_7a1000_evb.dts @@ -0,0 +1,68 @@ +// SPDX-License-Identifier: GPL-2.0 + +/dts-v1/; + +#include "loongson64g-package.dtsi" +#include "ls7a-pch.dtsi" + +/ { + compatible = "loongson,loongson64g-4core-ls7a"; + model = "loongson,ls3a4000_7a1000_evb"; + version = "v1.4"; +}; + +&package0 { + htvec: interrupt-controller@efdfb000080 { + compatible = "loongson,htvec-1.0"; + reg = <0xefd 0xfb000080 0x40>; + interrupt-controller; + #interrupt-cells = <1>; + + interrupt-parent = <&liointc>; + interrupts = <24 IRQ_TYPE_LEVEL_HIGH>, + <25 IRQ_TYPE_LEVEL_HIGH>, + <26 IRQ_TYPE_LEVEL_HIGH>, + <27 IRQ_TYPE_LEVEL_HIGH>, + <28 IRQ_TYPE_LEVEL_HIGH>, + <29 IRQ_TYPE_LEVEL_HIGH>, + <30 IRQ_TYPE_LEVEL_HIGH>, + <31 IRQ_TYPE_LEVEL_HIGH>; + }; +}; + +&pch { + msi: msi-controller@2ff00000 { + compatible = "loongson,pch-msi-1.0"; + reg = <0 0x2ff00000 0 0x8>; + interrupt-controller; + msi-controller; + loongson,msi-base-vec = <64>; + loongson,msi-num-vecs = <192>; + interrupt-parent = <&htvec>; + }; +}; + +&lsdc { + /* use_vram_helper; */ + output-ports = <&dvo0 &dvo1>; + + #address-cells = <1>; + #size-cells = <0>; + + dvo0: dvo@0 { + /* 0 for DVO0 */ + reg = <0>; + connector = "vga-connector"; + encoder = "adi,adv7125"; + status = "okay"; + }; + + dvo1: dvo@1 { + /* 1 for DVO1 */ + reg = <1>; + connector = "dvi-connector"; + encoder = "ti,tfp410"; + digital; + status = "okay"; + }; +}; diff --git a/arch/mips/boot/dts/loongson/ls7a-pch.dtsi b/arch/mips/boot/dts/loongson/ls7a-pch.dtsi index 2f45fce2cdc4..70a0b7ac0839 100644 --- a/arch/mips/boot/dts/loongson/ls7a-pch.dtsi +++ b/arch/mips/boot/dts/loongson/ls7a-pch.dtsi @@ -160,7 +160,7 @@ interrupt-parent = <&pic>; };
- dc@6,1 { + lsdc: dc@6,1 { compatible = "pci0014,7a06.0", "pci0014,7a06", "pciclass030000",
dri-devel@lists.freedesktop.org
-
Sui Jingfeng