The ANX7814 is an ultra-low power Full-HD (1080p60) SlimPort transmitter designed for portable devices.

Cc: Rob Herring robh@kernel.org Signed-off-by: Enric Balletbo i Serra enric.balletbo@collabora.com ---

Changes since v1: - Rob Herring: - Rename cable-det-gpios for hpd-gpios as is more standard - Fix HDMI output for HDMI input

.../devicetree/bindings/video/bridge/anx7814.txt | 41 ++++++++++++++++++++++ 1 file changed, 41 insertions(+) create mode 100644 Documentation/devicetree/bindings/video/bridge/anx7814.txt

diff --git a/Documentation/devicetree/bindings/video/bridge/anx7814.txt b/Documentation/devicetree/bindings/video/bridge/anx7814.txt new file mode 100644 index 0000000..0ce4978 --- /dev/null +++ b/Documentation/devicetree/bindings/video/bridge/anx7814.txt @@ -0,0 +1,41 @@ +Analogix ANX7814 SlimPort (Full-HD Transmitter) +----------------------------------------------- + +The ANX7814 is an ultra-low power Full-HD (1080p60) SlimPort transmitter +designed for portable devices. + +Required properties: + + - compatible : "analogix,anx7814" + - reg : I2C address of the device + - interrupt-parent : Should be the phandle of the interrupt controller + that services interrupts for this device + - interrupts : Should contain the INTP interrupt + - hpd-gpios : Which GPIO to use for hpd + - pd-gpios : Which GPIO to use for power down + - reset-gpios : Which GPIO to use for reset + +Optional properties: + + - v10-gpios : Which GPIO to use for V10 control. + - Video port for HDMI input, using the DT bindings defined in [1]. + +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + + anx7814: anx7814@38 { + compatible = "analogix,anx7814"; + reg = <0x38>; + interrupt-parent = <&gpio0>; + interrupts = <99 IRQ_TYPE_LEVEL_LOW>; /* INTP */ + hpd-gpios = <&pio 36 GPIO_ACTIVE_HIGH>; + pd-gpios = <&pio 33 GPIO_ACTIVE_HIGH>; + reset-gpios = <&pio 98 GPIO_ACTIVE_HIGH>; + v10-gpios = <&pio 35 GPIO_ACTIVE_HIGH>; + port { + anx7814_in: endpoint { + remote-endpoint = <&hdmi0_out>; + }; + }; + };

Although there are other chips from the same family that can reuse this driver, at the moment we only tested ANX7814 chip.

The ANX7814 is an ultra-low power Full-HD (1080p60) SlimPort transmitter designed for portable devices. This driver adds initial support for HDMI to DP pass-through mode.

Cc: Emil Velikov emil.l.velikov@gmail.com Cc: Rob Herring robh@kernel.org Cc: Dan Carpenter dan.carpenter@oracle.com Cc: Daniel Kurtz djkurtz@chromium.org Signed-off-by: Enric Balletbo i Serra enric.balletbo@collabora.com ---

Changes since v1: - Dan Carpenter: - Fix missing error code - Use meaningful names for goto exit paths - Rob Herring: - Use hpd instead cable_det as is the more standard name. - Daniel Kurtz: - Use regmap_bulk in aux_transfer - Fix gpio reset polarity. - Turn off v10 last so we mirror poweron sequence - Fix some error paths. - Remove mutex in anx78xx_detect - kbuild: - WARNING: PTR_ERR_OR_ZERO can be used

free any cached EDID on any plug event. drivers/gpu/drm/bridge/Kconfig | 8 + drivers/gpu/drm/bridge/Makefile | 1 + drivers/gpu/drm/bridge/anx78xx.c | 1411 ++++++++++++++++++++++++++++++++++++++ drivers/gpu/drm/bridge/anx78xx.h | 719 +++++++++++++++++++ 4 files changed, 2139 insertions(+) create mode 100644 drivers/gpu/drm/bridge/anx78xx.c create mode 100644 drivers/gpu/drm/bridge/anx78xx.h

diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig index 27e2022..0f595ae 100644 --- a/drivers/gpu/drm/bridge/Kconfig +++ b/drivers/gpu/drm/bridge/Kconfig @@ -40,4 +40,12 @@ config DRM_PARADE_PS8622 ---help--- Parade eDP-LVDS bridge chip driver.

+config DRM_ANX78XX + tristate "Analogix ANX78XX bridge" + select DRM_KMS_HELPER + select REGMAP_I2C + ---help--- + ANX78XX is a HD video transmitter chip over micro-USB connector + for smartphone device. + endmenu diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile index f13c33d..8f0d69e 100644 --- a/drivers/gpu/drm/bridge/Makefile +++ b/drivers/gpu/drm/bridge/Makefile @@ -4,3 +4,4 @@ obj-$(CONFIG_DRM_DW_HDMI) += dw-hdmi.o obj-$(CONFIG_DRM_DW_HDMI_AHB_AUDIO) += dw-hdmi-ahb-audio.o obj-$(CONFIG_DRM_NXP_PTN3460) += nxp-ptn3460.o obj-$(CONFIG_DRM_PARADE_PS8622) += parade-ps8622.o +obj-$(CONFIG_DRM_ANX78XX) += anx78xx.o diff --git a/drivers/gpu/drm/bridge/anx78xx.c b/drivers/gpu/drm/bridge/anx78xx.c new file mode 100644 index 0000000..995a2a7 --- /dev/null +++ b/drivers/gpu/drm/bridge/anx78xx.c @@ -0,0 +1,1411 @@ +/* + * Copyright(c) 2016, Analogix Semiconductor. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Based on anx7808 driver obtained from chromeos with copyright: + * Copyright(c) 2013, Google Inc. + * + */ +#include <linux/async.h> +#include <linux/delay.h> +#include <linux/err.h> +#include <linux/interrupt.h> +#include <linux/i2c.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/of_gpio.h> +#include <linux/of_irq.h> +#include <linux/of_platform.h> +#include <linux/regmap.h> +#include <linux/types.h> +#include <linux/gpio/consumer.h> +#include <drm/drmP.h> +#include <drm/drm_atomic_helper.h> +#include <drm/drm_crtc.h> +#include <drm/drm_crtc_helper.h> +#include <drm/drm_dp_helper.h> +#include <drm/drm_edid.h> + +#include "anx78xx.h" + +#define I2C_NUM_ADDRESSES 5 +#define I2C_IDX_TX_P0 0 +#define I2C_IDX_TX_P1 1 +#define I2C_IDX_TX_P2 2 +#define I2C_IDX_RX_P0 3 +#define I2C_IDX_RX_P1 4 + +#define XTAL_CLK 270 /* 27M */ +#define AUX_CH_BUFFER_SIZE 16 +#define AUX_WAIT_TIMEOUT_MS 15 +#define AUX_WAIT_INTERVAL_MS 1 + +/* + * _wait_for - magic (register) wait macro + * + * Does the right thing for modeset paths when run under kdgb or similar atomic + * contexts. Note that it's important that we check the condition again after + * having timed out, since the timeout could be due to preemption or similar and + * we've never had a chance to check the condition before the timeout. + */ +#define _wait_for(COND, TO_MS, INTVL_MS) ({ \ + unsigned long timeout__ = jiffies + msecs_to_jiffies(TO_MS) + 1;\ + int ret__ = 0; \ + while (!(COND)) { \ + if (time_after(jiffies, timeout__)) { \ + if (!(COND)) \ + ret__ = -ETIMEDOUT; \ + break; \ + } \ + if (drm_can_sleep()) { \ + usleep_range(INTVL_MS * 1000, \ + (INTVL_MS + 1) * 1000); \ + } else { \ + cpu_relax(); \ + } \ + } \ + ret__; \ +}) + +#define wait_for(COND, TO_MS, INTVL_MS) _wait_for(COND, TO_MS, INTVL_MS) + +static const u8 anx78xx_i2c_addresses[] = { + [I2C_IDX_TX_P0] = TX_P0, + [I2C_IDX_TX_P1] = TX_P1, + [I2C_IDX_TX_P2] = TX_P2, + [I2C_IDX_RX_P0] = RX_P0, + [I2C_IDX_RX_P1] = RX_P1, +}; + +struct anx78xx_platform_data { + struct gpio_desc *gpiod_hpd; + struct gpio_desc *gpiod_pd; + struct gpio_desc *gpiod_reset; + struct gpio_desc *gpiod_v10; + + int hpd_irq; + int intp_irq; +}; + +struct anx78xx { + struct drm_dp_aux aux; + struct drm_bridge bridge; + struct i2c_client *client; + struct edid *edid; + struct drm_connector connector; + struct drm_dp_link link; + struct anx78xx_platform_data pdata; + struct mutex lock; + + /* + * I2C Slave addresses of ANX7814 are mapped as TX_P0, TX_P1, TX_P2, + * RX_P0 and RX_P1. + */ + struct i2c_client *i2c_dummy[I2C_NUM_ADDRESSES]; + struct regmap *map[I2C_NUM_ADDRESSES]; + + u16 chipid; + u8 dpcd[DP_RECEIVER_CAP_SIZE]; + + bool powered; +}; + +static int anx78xx_set_bits(struct regmap *map, u8 reg, u8 mask) +{ + return regmap_update_bits(map, reg, mask, mask); +} + +static int anx78xx_clear_bits(struct regmap *map, u8 reg, u8 mask) +{ + return regmap_update_bits(map, reg, mask, 0); +} + +static int anx78xx_aux_op_finished(struct anx78xx *anx78xx) +{ + int err; + unsigned int aux_ctrl; + + err = regmap_read(anx78xx->map[I2C_IDX_TX_P0], SP_DP_AUX_CH_CTRL2_REG, + &aux_ctrl); + if (err) + return err; + + if (aux_ctrl & SP_AUX_EN) + return -EAGAIN; + + return 0; +} + +static int anx78xx_aux_wait(struct anx78xx *anx78xx) +{ + int err; + unsigned int status; + + err = wait_for(!anx78xx_aux_op_finished(anx78xx), AUX_WAIT_TIMEOUT_MS, + AUX_WAIT_INTERVAL_MS); + if (err) { + DRM_ERROR("Timed out waiting AUX to finish\n"); + return -ETIMEDOUT; + } + + /* Read the AUX channel access status */ + err = regmap_read(anx78xx->map[I2C_IDX_TX_P0], SP_AUX_CH_STATUS_REG, + &status); + if (err) + return err; + + if (status & SP_AUX_STATUS) { + DRM_ERROR("Failed to read AUX channel: 0x%02x\n", status); + return -ETIMEDOUT; + } + + return 0; +} + +static int anx78xx_aux_address(struct anx78xx *anx78xx, unsigned int addr) +{ + int err = 0; + + err |= regmap_write(anx78xx->map[I2C_IDX_TX_P0], SP_AUX_ADDR_7_0_REG, + addr & 0xff); + err |= regmap_write(anx78xx->map[I2C_IDX_TX_P0], SP_AUX_ADDR_15_8_REG, + (addr & 0xff00) >> 8); + + /* + * DP AUX CH Address Register #2, only update bits[3:0] + * [7:4] RESERVED + * [3:0] AUX_ADDR[19:16], Register control AUX CH address. + */ + err |= regmap_update_bits(anx78xx->map[I2C_IDX_TX_P0], + SP_AUX_ADDR_19_16_REG, + SP_AUX_ADDR_19_16_MASK, + (addr & 0xf0000) >> 16); + + if (err) + return -EIO; + + return 0; +} + +static ssize_t anx78xx_aux_transfer(struct drm_dp_aux *aux, + struct drm_dp_aux_msg *msg) +{ + int err = 0; + struct anx78xx *anx78xx = container_of(aux, struct anx78xx, aux); + u8 ctrl1 = msg->request; + u8 ctrl2 = SP_AUX_EN; + u8 *buffer = msg->buffer; + + /* The DP AUX transmit and receive buffer has 16 bytes. */ + if (WARN_ON(msg->size > AUX_CH_BUFFER_SIZE)) + return -E2BIG; + + /* Zero-sized messages specify address-only transactions. */ + if (msg->size < 1) + ctrl2 |= SP_ADDR_ONLY; + else /* For non-zero-sized set the length field. */ + ctrl1 |= (msg->size - 1) << SP_AUX_LENGTH_SHIFT; + + if ((msg->request & DP_AUX_I2C_READ) == 0) { + /* When WRITE | MOT write values to data buffer */ + err = regmap_bulk_write(anx78xx->map[I2C_IDX_TX_P0], + SP_DP_BUF_DATA0_REG, buffer, + msg->size); + if (err) + return -EIO; + } + + /* Write address and request */ + err |= anx78xx_aux_address(anx78xx, msg->address); + err |= regmap_write(anx78xx->map[I2C_IDX_TX_P0], SP_DP_AUX_CH_CTRL1_REG, + ctrl1); + if (err) + return -EIO; + + /* Start transaction */ + err |= regmap_update_bits(anx78xx->map[I2C_IDX_TX_P0], + SP_DP_AUX_CH_CTRL2_REG, SP_ADDR_ONLY | + SP_AUX_EN, ctrl2); + if (err) + return -EIO; + + err = anx78xx_aux_wait(anx78xx); + + msg->reply = err ? DP_AUX_I2C_REPLY_NACK : DP_AUX_I2C_REPLY_ACK; + + if ((msg->size > 0) && (msg->request & DP_AUX_I2C_READ)) { + /* Read values from data buffer */ + err = regmap_bulk_read(anx78xx->map[I2C_IDX_TX_P0], + SP_DP_BUF_DATA0_REG, buffer, + msg->size); + if (err) + return -EIO; + } + + err = anx78xx_clear_bits(anx78xx->map[I2C_IDX_TX_P0], + SP_DP_AUX_CH_CTRL2_REG, SP_ADDR_ONLY); + if (err) + return -EIO; + + return msg->size; +} + +static int anx78xx_set_hpd(struct anx78xx *anx78xx) +{ + int err = 0; + + err |= anx78xx_clear_bits(anx78xx->map[I2C_IDX_RX_P0], + SP_TMDS_CTRL_BASE + 7, SP_PD_RT); + err |= anx78xx_set_bits(anx78xx->map[I2C_IDX_TX_P2], SP_VID_CTRL3_REG, + SP_HPD_OUT); + + if (err) + return -EIO; + + return 0; +} + +static int anx78xx_clear_hpd(struct anx78xx *anx78xx) +{ + int err = 0; + + err |= anx78xx_clear_bits(anx78xx->map[I2C_IDX_TX_P2], SP_VID_CTRL3_REG, + SP_HPD_OUT); + err |= anx78xx_set_bits(anx78xx->map[I2C_IDX_RX_P0], + SP_TMDS_CTRL_BASE + 7, SP_PD_RT); + + if (err) + return -EIO; + + return 0; +} + +static const struct reg_sequence tmds_phy_initialization[] = { + { SP_TMDS_CTRL_BASE + 1, 0x90 }, + { SP_TMDS_CTRL_BASE + 2, 0xa9 }, + { SP_TMDS_CTRL_BASE + 6, 0x92 }, + { SP_TMDS_CTRL_BASE + 7, 0x80 }, + { SP_TMDS_CTRL_BASE + 20, 0xf2 }, + { SP_TMDS_CTRL_BASE + 22, 0xc4 }, + { SP_TMDS_CTRL_BASE + 23, 0x18 }, +}; + +static int anx78xx_rx_initialization(struct anx78xx *anx78xx) +{ + int err = 0; + + err |= regmap_write(anx78xx->map[I2C_IDX_RX_P0], SP_HDMI_MUTE_CTRL_REG, + SP_AUD_MUTE | SP_VID_MUTE); + + err |= anx78xx_set_bits(anx78xx->map[I2C_IDX_RX_P0], SP_CHIP_CTRL_REG, + SP_MAN_HDMI5V_DET | SP_PLLLOCK_CKDT_EN | + SP_DIGITAL_CKDT_EN); + + err |= anx78xx_set_bits(anx78xx->map[I2C_IDX_RX_P0], + SP_SOFTWARE_RESET1_REG, SP_HDCP_MAN_RST | + SP_SW_MAN_RST | SP_TMDS_RST | SP_VIDEO_RST); + + err |= anx78xx_clear_bits(anx78xx->map[I2C_IDX_RX_P0], + SP_SOFTWARE_RESET1_REG, SP_HDCP_MAN_RST | + SP_SW_MAN_RST | SP_TMDS_RST | SP_VIDEO_RST); + + /* Sync detect change, GP set mute */ + err |= anx78xx_set_bits(anx78xx->map[I2C_IDX_RX_P0], + SP_AUD_EXCEPTION_ENABLE_BASE + 1, BIT(5) | + BIT(6)); + + err |= anx78xx_set_bits(anx78xx->map[I2C_IDX_RX_P0], + SP_AUD_EXCEPTION_ENABLE_BASE + 3, + SP_AEC_EN21); + + err |= anx78xx_set_bits(anx78xx->map[I2C_IDX_RX_P0], SP_AUDVID_CTRL_REG, + SP_AVC_EN | SP_AAC_OE | SP_AAC_EN); + + err |= anx78xx_clear_bits(anx78xx->map[I2C_IDX_RX_P0], + SP_SYSTEM_POWER_DOWN1_REG, SP_PWDN_CTRL); + + err |= anx78xx_set_bits(anx78xx->map[I2C_IDX_RX_P0], + SP_VID_DATA_RANGE_CTRL_REG, SP_R2Y_INPUT_LIMIT); + + /* Enable DDC stretch */ + err |= regmap_write(anx78xx->map[I2C_IDX_TX_P0], + SP_DP_EXTRA_I2C_DEV_ADDR_REG, SP_I2C_EXTRA_ADDR); + + /* TMDS phy initialization */ + err |= regmap_multi_reg_write(anx78xx->map[I2C_IDX_RX_P0], + tmds_phy_initialization, + ARRAY_SIZE(tmds_phy_initialization)); + + err |= anx78xx_clear_hpd(anx78xx); + + if (err) + return -EIO; + + return 0; +} + +static const u8 dp_tx_output_precise_tune_bits[20] = { + 0x01, 0x03, 0x07, 0x7f, 0x71, 0x6b, 0x7f, + 0x73, 0x7f, 0x7f, 0x00, 0x00, 0x00, 0x00, + 0x0c, 0x42, 0x1e, 0x3e, 0x72, 0x7e, +}; + +static int anx78xx_link_phy_initialization(struct anx78xx *anx78xx) +{ + int err = 0; + + /* + * REVISIT : It is writing to a RESERVED bits in Analog Control 0 + * register. + */ + err |= regmap_write(anx78xx->map[I2C_IDX_TX_P2], SP_ANALOG_CTRL0_REG, + 0x02); + + /* + * Write DP TX output emphasis precise tune bits. + */ + err |= regmap_bulk_write(anx78xx->map[I2C_IDX_TX_P1], + SP_DP_TX_LT_CTRL0_REG, + dp_tx_output_precise_tune_bits, + ARRAY_SIZE(dp_tx_output_precise_tune_bits)); + + if (err) + return -EIO; + + return 0; +} + +static int anx78xx_xtal_clk_sel(struct anx78xx *anx78xx) +{ + int err = 0; + unsigned int regval; + + err |= regmap_update_bits(anx78xx->map[I2C_IDX_TX_P2], + SP_ANALOG_DEBUG2_REG, + SP_XTAL_FRQ | SP_FORCE_SW_OFF_BYPASS, + SP_XTAL_FRQ_27M); + + err |= regmap_write(anx78xx->map[I2C_IDX_TX_P0], SP_DP_AUX_CH_CTRL3_REG, + XTAL_CLK & SP_WAIT_COUNTER_7_0_MASK); + + err |= regmap_write(anx78xx->map[I2C_IDX_TX_P0], SP_DP_AUX_CH_CTRL4_REG, + ((XTAL_CLK & 0xff00) >> 2) | (XTAL_CLK / 10)); + + err |= regmap_write(anx78xx->map[I2C_IDX_TX_P0], + SP_I2C_GEN_10US_TIMER0_REG, XTAL_CLK & 0xff); + + err |= regmap_write(anx78xx->map[I2C_IDX_TX_P0], + SP_I2C_GEN_10US_TIMER1_REG, + (XTAL_CLK & 0xff00) >> 8); + + err |= regmap_write(anx78xx->map[I2C_IDX_TX_P0], SP_AUX_MISC_CTRL_REG, + XTAL_CLK / 10 - 1); + + err |= regmap_read(anx78xx->map[I2C_IDX_RX_P0], + SP_HDMI_US_TIMER_CTRL_REG, + &regval); + + err |= regmap_write(anx78xx->map[I2C_IDX_RX_P0], + SP_HDMI_US_TIMER_CTRL_REG, + (regval & SP_MS_TIMER_MARGIN_10_8_MASK) | + ((((XTAL_CLK / 10) >> 1) - 2) << 3)); + + if (err) + return -EIO; + + return 0; +} + +static const struct reg_sequence otp_key_protect[] = { + { SP_OTP_KEY_PROTECT1_REG, SP_OTP_PSW1 }, + { SP_OTP_KEY_PROTECT2_REG, SP_OTP_PSW2 }, + { SP_OTP_KEY_PROTECT3_REG, SP_OTP_PSW3 }, +}; + +static int anx78xx_tx_initialization(struct anx78xx *anx78xx) +{ + int err = 0; + + /* Set terminal resistor to 50 ohm */ + err |= regmap_write(anx78xx->map[I2C_IDX_TX_P0], SP_DP_AUX_CH_CTRL2_REG, + 0x30); + + /* Enable aux double diff output */ + err |= anx78xx_set_bits(anx78xx->map[I2C_IDX_TX_P0], + SP_DP_AUX_CH_CTRL2_REG, 0x08); + + err |= anx78xx_clear_bits(anx78xx->map[I2C_IDX_TX_P0], + SP_DP_HDCP_CTRL_REG, SP_AUTO_EN | + SP_AUTO_START); + + err |= regmap_multi_reg_write(anx78xx->map[I2C_IDX_TX_P0], + otp_key_protect, + ARRAY_SIZE(otp_key_protect)); + + err |= anx78xx_set_bits(anx78xx->map[I2C_IDX_TX_P0], + SP_HDCP_KEY_COMMAND_REG, SP_DISABLE_SYNC_HDCP); + + err |= regmap_write(anx78xx->map[I2C_IDX_TX_P2], SP_VID_CTRL8_REG, + SP_VID_VRES_TH); + + /* + * DP HDCP auto authentication wait timer (when downstream starts to + * auth, DP side will wait for this period then do auth automatically) + */ + err |= regmap_write(anx78xx->map[I2C_IDX_TX_P0], SP_HDCP_AUTO_TIMER_REG, + 0x00); + + err |= anx78xx_set_bits(anx78xx->map[I2C_IDX_TX_P0], + SP_DP_HDCP_CTRL_REG, SP_LINK_POLLING); + + err |= anx78xx_set_bits(anx78xx->map[I2C_IDX_TX_P0], + SP_DP_LINK_DEBUG_CTRL_REG, SP_M_VID_DEBUG); + + err |= anx78xx_set_bits(anx78xx->map[I2C_IDX_TX_P2], + SP_ANALOG_DEBUG2_REG, SP_POWERON_TIME_1P5MS); + + err |= anx78xx_xtal_clk_sel(anx78xx); + + err |= regmap_write(anx78xx->map[I2C_IDX_TX_P0], SP_AUX_DEFER_CTRL_REG, + SP_DEFER_CTRL_EN | 0x0c); + + err |= anx78xx_set_bits(anx78xx->map[I2C_IDX_TX_P0], + SP_DP_POLLING_CTRL_REG, + SP_AUTO_POLLING_DISABLE); + + /* + * Short the link integrity check timer to speed up bstatus + * polling for HDCP CTS item 1A-07 + */ + err |= regmap_write(anx78xx->map[I2C_IDX_TX_P0], + SP_HDCP_LINK_CHECK_TIMER_REG, 0x1d); + + err |= anx78xx_set_bits(anx78xx->map[I2C_IDX_TX_P0], + SP_DP_MISC_CTRL_REG, SP_EQ_TRAINING_LOOP); + + /* Power down the main link by default */ + err |= anx78xx_set_bits(anx78xx->map[I2C_IDX_TX_P0], + SP_DP_ANALOG_POWER_DOWN_REG, SP_CH0_PD); + + err |= anx78xx_link_phy_initialization(anx78xx); + + /* Gen m_clk with downspreading */ + err |= anx78xx_set_bits(anx78xx->map[I2C_IDX_TX_P0], + SP_DP_M_CALCULATION_CTRL_REG, SP_M_GEN_CLK_SEL); + + if (err) + return -EIO; + + return 0; +} + +static int anx78xx_enable_interrupts(struct anx78xx *anx78xx) +{ + int err = 0; + + /* + * BIT0: INT pin assertion polarity: 1 = assert high + * BIT1: INT pin output type: 0 = push/pull + */ + err |= regmap_write(anx78xx->map[I2C_IDX_TX_P2], SP_INT_CTRL_REG, 0x01); + + err |= regmap_write(anx78xx->map[I2C_IDX_TX_P2], + SP_COMMON_INT_MASK4_REG, SP_HPD_LOST | SP_HPD_PLUG); + + err |= regmap_write(anx78xx->map[I2C_IDX_TX_P2], SP_DP_INT_MASK1_REG, + SP_TRAINING_FINISH); + + err |= regmap_write(anx78xx->map[I2C_IDX_RX_P0], SP_INT_MASK1_REG, + SP_CKDT_CHG | SP_SCDT_CHG); + + if (err) + return -EIO; + + return 0; +} + +static void anx78xx_poweron(struct anx78xx *anx78xx) +{ + struct anx78xx_platform_data *pdata = &anx78xx->pdata; + + if (WARN_ON(anx78xx->powered)) + return; + + if (pdata->gpiod_v10) { + gpiod_set_value_cansleep(pdata->gpiod_v10, 1); + usleep_range(1000, 2000); + } + + gpiod_set_value_cansleep(pdata->gpiod_reset, 1); + usleep_range(1000, 2000); + + gpiod_set_value_cansleep(pdata->gpiod_pd, 0); + usleep_range(1000, 2000); + + gpiod_set_value_cansleep(pdata->gpiod_reset, 0); + + /* Power on registers module */ + anx78xx_set_bits(anx78xx->map[I2C_IDX_TX_P2], SP_POWERDOWN_CTRL_REG, + SP_HDCP_PD | SP_AUDIO_PD | SP_VIDEO_PD | SP_LINK_PD); + anx78xx_clear_bits(anx78xx->map[I2C_IDX_TX_P2], SP_POWERDOWN_CTRL_REG, + SP_REGISTER_PD | SP_TOTAL_PD); + + anx78xx->powered = true; +} + +static void anx78xx_poweroff(struct anx78xx *anx78xx) +{ + struct anx78xx_platform_data *pdata = &anx78xx->pdata; + + if (WARN_ON(!anx78xx->powered)) + return; + + gpiod_set_value_cansleep(pdata->gpiod_reset, 1); + usleep_range(1000, 2000); + + gpiod_set_value_cansleep(pdata->gpiod_pd, 1); + usleep_range(1000, 2000); + + if (pdata->gpiod_v10) { + gpiod_set_value_cansleep(pdata->gpiod_v10, 0); + usleep_range(1000, 2000); + } + + anx78xx->powered = false; +} + +static int anx78xx_start(struct anx78xx *anx78xx) +{ + int err = 0; + + /* Power on all modules */ + err |= anx78xx_clear_bits(anx78xx->map[I2C_IDX_TX_P2], + SP_POWERDOWN_CTRL_REG, + SP_HDCP_PD | SP_AUDIO_PD | SP_VIDEO_PD | + SP_LINK_PD); + + err |= anx78xx_enable_interrupts(anx78xx); + err |= anx78xx_rx_initialization(anx78xx); + err |= anx78xx_tx_initialization(anx78xx); + + if (err) { + DRM_ERROR("Failed SlimPort transmitter initialization\n"); + anx78xx_poweroff(anx78xx); + return -EIO; + } + + /* + * This delay seems to help keep the hardware in a good state. Without + * it, there are times where it fails silently. + */ + usleep_range(10000, 15000); + + return 0; +} + +static int anx78xx_init_gpio(struct anx78xx *anx78xx) +{ + struct device *dev = &anx78xx->client->dev; + struct anx78xx_platform_data *pdata = &anx78xx->pdata; + + /* GPIO for hpd */ + pdata->gpiod_hpd = devm_gpiod_get(dev, "hpd", GPIOD_IN); + if (IS_ERR(pdata->gpiod_hpd)) + return PTR_ERR(pdata->gpiod_hpd); + + /* GPIO for chip power down */ + pdata->gpiod_pd = devm_gpiod_get(dev, "pd", GPIOD_OUT_HIGH); + if (IS_ERR(pdata->gpiod_pd)) + return PTR_ERR(pdata->gpiod_pd); + + /* GPIO for chip reset */ + pdata->gpiod_reset = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW); + if (IS_ERR(pdata->gpiod_reset)) + return PTR_ERR(pdata->gpiod_reset); + + /* GPIO for V10 power control */ + pdata->gpiod_v10 = devm_gpiod_get_optional(dev, "v10", GPIOD_OUT_LOW); + + return PTR_ERR_OR_ZERO(pdata->gpiod_v10); +} + +static int anx78xx_dp_link_training(struct anx78xx *anx78xx) +{ + int err = 0; + u8 dp_bw, regval; + + err |= regmap_write(anx78xx->map[I2C_IDX_RX_P0], SP_HDMI_MUTE_CTRL_REG, + 0x0); + err |= anx78xx_clear_bits(anx78xx->map[I2C_IDX_TX_P2], + SP_POWERDOWN_CTRL_REG, + SP_TOTAL_PD); + if (err) + return -EIO; + + err = drm_dp_dpcd_readb(&anx78xx->aux, DP_MAX_LINK_RATE, &dp_bw); + if (err < 0) + return err; + + switch (dp_bw) { + case DP_LINK_BW_1_62: + case DP_LINK_BW_2_7: + case DP_LINK_BW_5_4: + break; + default: + DRM_DEBUG_KMS("Waiting to read DP bandwidth.\n"); + return -EAGAIN; + } + + err = anx78xx_set_bits(anx78xx->map[I2C_IDX_TX_P2], SP_VID_CTRL1_REG, + SP_VIDEO_MUTE); + err |= anx78xx_clear_bits(anx78xx->map[I2C_IDX_TX_P2], + SP_VID_CTRL1_REG, SP_VIDEO_EN); + if (err) + return -EIO; + + /* Get dpcd info */ + err = drm_dp_dpcd_read(&anx78xx->aux, DP_DPCD_REV, + &anx78xx->dpcd, DP_RECEIVER_CAP_SIZE); + if (err < 0) { + DRM_ERROR("Failed to read DPCD\n"); + return err; + } + + /* Clear channel x SERDES power down */ + err = anx78xx_clear_bits(anx78xx->map[I2C_IDX_TX_P0], + SP_DP_ANALOG_POWER_DOWN_REG, SP_CH0_PD); + if (err) + return -EIO; + + /* Check link capabilities */ + err = drm_dp_link_probe(&anx78xx->aux, &anx78xx->link); + if (err < 0) { + DRM_ERROR("Failed to probe link capabilities\n"); + return err; + } + + /* Power up the sink */ + err = drm_dp_link_power_up(&anx78xx->aux, &anx78xx->link); + if (err < 0) { + DRM_ERROR("Failed to power up DisplayPort link\n"); + return err; + } + + /* Possibly enable downspread on the sink */ + err = regmap_write(anx78xx->map[I2C_IDX_TX_P0], + SP_DP_DOWNSPREAD_CTRL1_REG, 0); + if (err) + return -EIO; + + if (anx78xx->dpcd[3] & 0x1) { + DRM_DEBUG("Enable downspread on the sink\n"); + /* 4000PPM */ + err = regmap_write(anx78xx->map[I2C_IDX_TX_P0], + SP_DP_DOWNSPREAD_CTRL1_REG, 8); + if (err) + return -EIO; + + err = drm_dp_dpcd_writeb(&anx78xx->aux, DP_DOWNSPREAD_CTRL, + DP_SPREAD_AMP_0_5); + if (err < 0) + return err; + } else { + err = drm_dp_dpcd_writeb(&anx78xx->aux, DP_DOWNSPREAD_CTRL, 0); + if (err < 0) + return err; + } + + /* Set the lane count and the link rate on the sink */ + if (drm_dp_enhanced_frame_cap(anx78xx->dpcd)) + err = anx78xx_set_bits(anx78xx->map[I2C_IDX_TX_P0], + SP_DP_SYSTEM_CTRL_BASE + 4, + SP_ENHANCED_MODE); + else + err = anx78xx_clear_bits(anx78xx->map[I2C_IDX_TX_P0], + SP_DP_SYSTEM_CTRL_BASE + 4, + SP_ENHANCED_MODE); + if (err) + return -EIO; + + regval = drm_dp_link_rate_to_bw_code(anx78xx->link.rate); + err = regmap_write(anx78xx->map[I2C_IDX_TX_P0], + SP_DP_MAIN_LINK_BW_SET_REG, regval); + if (err) + return -EIO; + + err = drm_dp_link_configure(&anx78xx->aux, &anx78xx->link); + if (err < 0) { + DRM_ERROR("Failed to configure DisplayPort link\n"); + return err; + } + + /* Start training on the source */ + err = regmap_write(anx78xx->map[I2C_IDX_TX_P0], SP_DP_LT_CTRL_REG, + SP_LT_EN); + if (err) + return -EIO; + + return 0; +} + +static int anx78xx_config_dp_output(struct anx78xx *anx78xx) +{ + int err = 0; + + err |= anx78xx_clear_bits(anx78xx->map[I2C_IDX_TX_P2], SP_VID_CTRL1_REG, + SP_VIDEO_MUTE); + /* Enable DP output */ + err |= anx78xx_set_bits(anx78xx->map[I2C_IDX_TX_P2], SP_VID_CTRL1_REG, + SP_VIDEO_EN); + + if (err) + return -EIO; + + return 0; +} + +static int anx78xx_send_video_infoframe(struct anx78xx *anx78xx, + struct hdmi_avi_infoframe *frame) +{ + int err; + u8 buffer[HDMI_INFOFRAME_HEADER_SIZE + HDMI_AVI_INFOFRAME_SIZE]; + + err = hdmi_avi_infoframe_pack(frame, buffer, sizeof(buffer)); + if (err < 0) { + DRM_ERROR("Failed to pack AVI infoframe: %d\n", err); + return err; + } + + err = anx78xx_clear_bits(anx78xx->map[I2C_IDX_TX_P0], + SP_PACKET_SEND_CTRL_REG, SP_AVI_IF_EN); + + err |= regmap_bulk_write(anx78xx->map[I2C_IDX_TX_P2], + SP_INFOFRAME_AVI_DB1_REG, buffer, + frame->length); + + err |= anx78xx_set_bits(anx78xx->map[I2C_IDX_TX_P0], + SP_PACKET_SEND_CTRL_REG, SP_AVI_IF_UD); + + err |= anx78xx_set_bits(anx78xx->map[I2C_IDX_TX_P0], + SP_PACKET_SEND_CTRL_REG, SP_AVI_IF_EN); + + if (err) + return -EIO; + + return 0; +} + +static inline struct anx78xx * + connector_to_anx78xx(struct drm_connector *connector) +{ + return container_of(connector, struct anx78xx, connector); +} + +static int anx78xx_get_downstream_info(struct anx78xx *anx78xx) +{ + int err; + u8 regval; + + err = drm_dp_dpcd_readb(&anx78xx->aux, DP_SINK_COUNT, &regval); + if (err < 0) { + DRM_ERROR("Get sink count failed %d\n", err); + return err; + } + + if (!DP_GET_SINK_COUNT(regval)) { + DRM_ERROR("Downstream disconnected\n"); + return -EIO; + } + + return 0; +} + +static int anx78xx_get_modes(struct drm_connector *connector) +{ + int err, num_modes = 0; + struct anx78xx *anx78xx = connector_to_anx78xx(connector); + + if (WARN_ON(!anx78xx->powered)) + return 0; + + if (anx78xx->edid) + return drm_add_edid_modes(connector, anx78xx->edid); + + mutex_lock(&anx78xx->lock); + + err = anx78xx_get_downstream_info(anx78xx); + if (err) { + DRM_ERROR("Failed to get downstream info: %d\n", err); + goto unlock; + } + + anx78xx->edid = drm_get_edid(connector, &anx78xx->aux.ddc); + if (!anx78xx->edid) { + DRM_ERROR("Failed to read edid\n"); + goto unlock; + } + + err = drm_mode_connector_update_edid_property(connector, + anx78xx->edid); + if (err) { + DRM_ERROR("Failed to update edid property\n"); + goto unlock; + } + + num_modes = drm_add_edid_modes(connector, anx78xx->edid); + /* Store the ELD */ + drm_edid_to_eld(connector, anx78xx->edid); + +unlock: + mutex_unlock(&anx78xx->lock); + + return num_modes; +} + +static struct drm_encoder *anx78xx_best_encoder(struct drm_connector *connector) +{ + struct anx78xx *anx78xx = connector_to_anx78xx(connector); + + return anx78xx->bridge.encoder; +} + +static const struct drm_connector_helper_funcs + anx78xx_connector_helper_funcs = { + .get_modes = anx78xx_get_modes, + .best_encoder = anx78xx_best_encoder, +}; + +static enum drm_connector_status anx78xx_detect(struct drm_connector *connector, + bool force) +{ + struct anx78xx *anx78xx = container_of(connector, struct anx78xx, + connector); + + DRM_DEBUG_KMS("[CONNECTOR:%d:%s]\n", connector->base.id, + connector->name); + + if (!gpiod_get_value(anx78xx->pdata.gpiod_hpd)) { + DRM_DEBUG_KMS("CONNECTOR STATUS DISCONNECTED\n"); + return connector_status_disconnected; + } + + return connector_status_connected; +} + +static void anx78xx_connector_destroy(struct drm_connector *connector) +{ + drm_connector_cleanup(connector); +} + +static const struct drm_connector_funcs anx78xx_connector_funcs = { + .dpms = drm_atomic_helper_connector_dpms, + .fill_modes = drm_helper_probe_single_connector_modes, + .detect = anx78xx_detect, + .destroy = anx78xx_connector_destroy, + .reset = drm_atomic_helper_connector_reset, + .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, + .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, +}; + +static inline struct anx78xx *bridge_to_anx78xx(struct drm_bridge *bridge) +{ + return container_of(bridge, struct anx78xx, bridge); +} + +static int anx78xx_bridge_attach(struct drm_bridge *bridge) +{ + struct anx78xx *anx78xx = bridge_to_anx78xx(bridge); + int err; + + if (!bridge->encoder) { + DRM_ERROR("Parent encoder object not found"); + return -ENODEV; + } + + /* Register aux channel */ + anx78xx->aux.name = "DP-AUX"; + anx78xx->aux.dev = &anx78xx->client->dev; + anx78xx->aux.transfer = anx78xx_aux_transfer; + + err = drm_dp_aux_register(&anx78xx->aux); + if (err < 0) { + DRM_ERROR("Failed to register aux channel: %d\n", err); + return err; + } + + err = drm_connector_init(bridge->dev, &anx78xx->connector, + &anx78xx_connector_funcs, + DRM_MODE_CONNECTOR_DisplayPort); + if (err) { + DRM_ERROR("Failed to initialize connector: %d\n", err); + return err; + } + + drm_connector_helper_add(&anx78xx->connector, + &anx78xx_connector_helper_funcs); + + err = drm_connector_register(&anx78xx->connector); + if (err) { + DRM_ERROR("Failed to register connector: %d\n", err); + return err; + } + + anx78xx->connector.polled = DRM_CONNECTOR_POLL_HPD; + + err = drm_mode_connector_attach_encoder(&anx78xx->connector, + bridge->encoder); + if (err) { + DRM_ERROR("Failed to link up connector to encoder: %d\n", err); + return err; + } + + return 0; +} + +static bool anx78xx_bridge_mode_fixup(struct drm_bridge *bridge, + const struct drm_display_mode *mode, + struct drm_display_mode *adjusted_mode) +{ + if (mode->flags & DRM_MODE_FLAG_INTERLACE) + return false; + + /* Max 1200p at 5.4 Ghz, one lane */ + if (mode->clock > 154000) + return false; + + return true; +} + +static void anx78xx_bridge_disable(struct drm_bridge *bridge) { + struct anx78xx *anx78xx = bridge_to_anx78xx(bridge); + + mutex_lock(&anx78xx->lock); + + /* Power off all modules except configuration registers access */ + anx78xx_set_bits(anx78xx->map[I2C_IDX_TX_P2], SP_POWERDOWN_CTRL_REG, + SP_HDCP_PD | SP_AUDIO_PD | SP_VIDEO_PD | SP_LINK_PD); + + mutex_unlock(&anx78xx->lock); +} + +static void anx78xx_bridge_mode_set(struct drm_bridge *bridge, + struct drm_display_mode *mode, + struct drm_display_mode *adjusted_mode) +{ + int err; + struct hdmi_avi_infoframe frame; + struct anx78xx *anx78xx = bridge_to_anx78xx(bridge); + + if (WARN_ON(!anx78xx->powered)) + return; + + mutex_lock(&anx78xx->lock); + + mode = adjusted_mode; + + err = drm_hdmi_avi_infoframe_from_display_mode(&frame, mode); + if (err) { + DRM_ERROR("Failed to setup AVI infoframe: %d\n", err); + goto unlock; + } + + err = anx78xx_send_video_infoframe(anx78xx, &frame); + if (err) + DRM_ERROR("Failed to send AVI infoframe: %d\n", err); + +unlock: + mutex_unlock(&anx78xx->lock); +} + +static void anx78xx_bridge_enable(struct drm_bridge *bridge) { + int err; + struct anx78xx *anx78xx = bridge_to_anx78xx(bridge); + + mutex_lock(&anx78xx->lock); + + err = anx78xx_start(anx78xx); + if (err) + DRM_ERROR("Failed to initialize: %d\n", err); + + err = anx78xx_set_hpd(anx78xx); + if (err) + DRM_ERROR("Failed to set HPD: %d\n", err); + + mutex_unlock(&anx78xx->lock); +} + +static const struct drm_bridge_funcs anx78xx_bridge_funcs = { + .attach = anx78xx_bridge_attach, + .mode_fixup = anx78xx_bridge_mode_fixup, + .disable = anx78xx_bridge_disable, + .mode_set = anx78xx_bridge_mode_set, + .enable = anx78xx_bridge_enable, +}; + +static irqreturn_t anx78xx_hpd_threaded_handler(int unused, void *data) +{ + int err; + struct anx78xx *anx78xx = data; + + if (anx78xx->powered) + return IRQ_HANDLED; + + mutex_lock(&anx78xx->lock); + + /* Cable is pulled, power on the chip */ + anx78xx_poweron(anx78xx); + + err = anx78xx_enable_interrupts(anx78xx); + if (err) + DRM_ERROR("Failed to enable interrupts: %d\n", err); + + mutex_unlock(&anx78xx->lock); + + return IRQ_HANDLED; +} + +static int anx78xx_handle_dp_int_1(struct anx78xx *anx78xx, u8 irq) +{ + int err; + + DRM_DEBUG_KMS("Handle DP interrupt 1: %02x\n", irq); + + err = regmap_write(anx78xx->map[I2C_IDX_TX_P2], SP_DP_INT_STATUS1_REG, + irq); + if (err) + return err; + + if (irq & SP_TRAINING_FINISH) { + DRM_DEBUG_KMS("IRQ: hardware link training finished\n"); + err = anx78xx_config_dp_output(anx78xx); + } + + return err; +} + +static bool anx78xx_handle_common_int_4(struct anx78xx *anx78xx, u8 irq) +{ + int err; + bool event = false; + + DRM_DEBUG_KMS("Handle common interrupt 4: %02x\n", irq); + + err = regmap_write(anx78xx->map[I2C_IDX_TX_P2], + SP_COMMON_INT_STATUS4_REG, irq); + if (err) { + DRM_ERROR("Failed to write SP_COMMON_INT_STATUS4 %d\n", err); + return event; + } + + if (irq & SP_HPD_LOST) { + DRM_DEBUG_KMS("IRQ: Hot plug detect - cable is pulled out\n"); + event = true; + anx78xx_poweroff(anx78xx); + } else if (irq & SP_HPD_PLUG) { + DRM_DEBUG_KMS("IRQ: Hot plug detect - cable plug\n"); + event = true; + /* Free previous cached EDID if any */ + kfree(anx78xx->edid); + anx78xx->edid = NULL; + } + + return event; +} + +static void anx78xx_handle_hdmi_int_1(struct anx78xx *anx78xx, u8 irq) +{ + int err; + unsigned int regval; + + DRM_DEBUG_KMS("Handle HDMI interrupt 1: %02x\n", irq); + + err = regmap_write(anx78xx->map[I2C_IDX_RX_P0], SP_INT_STATUS1_REG, + irq); + if (err) { + DRM_ERROR("Write hdmi int 1 failed %d\n", err); + return; + } + + if ((irq & SP_CKDT_CHG) || (irq & SP_SCDT_CHG)) { + DRM_DEBUG_KMS("IRQ: HDMI input detected\n"); + err = regmap_read(anx78xx->map[I2C_IDX_RX_P0], + SP_SYSTEM_STATUS_REG, &regval); + if (err) { + DRM_ERROR("Read system status reg failed %d\n", err); + return; + } + + if (!(regval & SP_TMDS_CLOCK_DET)) { + DRM_DEBUG_KMS("IRQ: *** Waiting for HDMI clock ***\n"); + return; + } + if (!(regval & SP_TMDS_DE_DET)) { + DRM_DEBUG_KMS("IRQ: *** Waiting for HDMI signal ***\n"); + return; + } + + err = anx78xx_dp_link_training(anx78xx); + if (err) + DRM_ERROR("Failed to start link training: %d\n", err); + } +} + +static irqreturn_t anx78xx_intp_threaded_handler(int unused, void *data) +{ + struct anx78xx *anx78xx = data; + int err; + unsigned int irq; + bool event = false; + + mutex_lock(&anx78xx->lock); + + err = regmap_read(anx78xx->map[I2C_IDX_TX_P2], SP_DP_INT_STATUS1_REG, + &irq); + if (err) { + DRM_ERROR("Failed to read dp int 1 status %d\n", err); + goto unlock; + } else if (irq) { + anx78xx_handle_dp_int_1(anx78xx, irq); + } + + err = regmap_read(anx78xx->map[I2C_IDX_TX_P2], + SP_COMMON_INT_STATUS4_REG, &irq); + if (err) { + DRM_ERROR("Failed to read common int 4 status %d\n", err); + goto unlock; + } else if (irq) { + event = anx78xx_handle_common_int_4(anx78xx, irq); + } + + /* Make sure we are still powered after handle HPD events */ + if (!anx78xx->powered) + goto unlock; + + err = regmap_read(anx78xx->map[I2C_IDX_RX_P0], SP_INT_STATUS1_REG, + &irq); + if (err) + DRM_ERROR("Failed to read hdmi int 1 status %d\n", err); + else if (irq) + anx78xx_handle_hdmi_int_1(anx78xx, irq); + +unlock: + mutex_unlock(&anx78xx->lock); + + if (event) + drm_helper_hpd_irq_event(anx78xx->connector.dev); + + return IRQ_HANDLED; +} + +static void unregister_i2c_dummy_clients(struct anx78xx *anx78xx) +{ + int i; + + for (i = 0; i < ARRAY_SIZE(anx78xx->i2c_dummy); i++) + if (anx78xx->i2c_dummy[i]) + i2c_unregister_device(anx78xx->i2c_dummy[i]); +} + +static const struct regmap_config anx78xx_regmap_config = { + .reg_bits = 8, + .val_bits = 8, +}; + +static const u16 anx78xx_chipid_list[] = { + 0x7812, + 0x7814, + 0x7818, +}; + +static int anx78xx_i2c_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct anx78xx *anx78xx; + struct anx78xx_platform_data *pdata; + int err, i; + unsigned int idl, idh, version; + bool found = false; + + anx78xx = devm_kzalloc(&client->dev, sizeof(*anx78xx), GFP_KERNEL); + if (!anx78xx) + return -ENOMEM; + + pdata = &anx78xx->pdata; + + mutex_init(&anx78xx->lock); + +#if IS_ENABLED(CONFIG_OF) + anx78xx->bridge.of_node = client->dev.of_node; +#endif + + anx78xx->client = client; + i2c_set_clientdata(client, anx78xx); + + err = anx78xx_init_gpio(anx78xx); + if (err) { + DRM_ERROR("Failed to initialize gpios\n"); + return err; + } + + pdata->hpd_irq = gpiod_to_irq(pdata->gpiod_hpd); + if (pdata->hpd_irq < 0) { + DRM_ERROR("Failed to get hpd irq %d\n", + pdata->hpd_irq); + return -ENODEV; + } + + pdata->intp_irq = client->irq; + if (!pdata->intp_irq) { + DRM_ERROR("Failed to get CABLE_DET and INTP irq\n"); + return -ENODEV; + } + + /* Map slave addresses of ANX7814 */ + for (i = 0; i < I2C_NUM_ADDRESSES; i++) { + anx78xx->i2c_dummy[i] = i2c_new_dummy(client->adapter, + anx78xx_i2c_addresses[i] >> 1); + if (!anx78xx->i2c_dummy[i]) { + err = -ENOMEM; + DRM_ERROR("Failed to reserve i2c bus %02x.\n", + anx78xx_i2c_addresses[i]); + goto err_unregister_i2c; + } + + anx78xx->map[i] = devm_regmap_init_i2c(anx78xx->i2c_dummy[i], + &anx78xx_regmap_config); + if (IS_ERR(anx78xx->map[i])) { + err = PTR_ERR(anx78xx->map[i]); + DRM_ERROR("Failed regmap initialization %02x.\n", + anx78xx_i2c_addresses[i]); + goto err_unregister_i2c; + } + } + + /* Look for supported chip id */ + anx78xx_poweron(anx78xx); + + err = regmap_read(anx78xx->map[I2C_IDX_TX_P2], SP_DEVICE_IDL_REG, + &idl); + if (err) + goto err_poweroff; + + err = regmap_read(anx78xx->map[I2C_IDX_TX_P2], SP_DEVICE_IDH_REG, + &idh); + if (err) + goto err_poweroff; + + anx78xx->chipid = (u8)idl | ((u8)idh << 8); + + err = regmap_read(anx78xx->map[I2C_IDX_TX_P2], SP_DEVICE_VERSION_REG, + &version); + if (err) + goto err_poweroff; + + for (i = 0; i < ARRAY_SIZE(anx78xx_chipid_list); i++) { + if (anx78xx->chipid == anx78xx_chipid_list[i]) { + DRM_INFO("Found ANX%x (ver. %d) SlimPort Transmitter\n", + anx78xx->chipid, version); + found = true; + break; + } + } + + if (!found) { + DRM_ERROR("ANX%x (ver. %d) not supported by this driver\n", + anx78xx->chipid, version); + err = -ENODEV; + goto err_poweroff; + } + + err = devm_request_threaded_irq(&client->dev, pdata->hpd_irq, + NULL, + anx78xx_hpd_threaded_handler, + IRQF_TRIGGER_RISING | IRQF_ONESHOT, + "anx78xx-hpd", anx78xx); + if (err) { + DRM_ERROR("Failed to request CABLE_DET threaded irq\n"); + goto err_poweroff; + } + + err = devm_request_threaded_irq(&client->dev, pdata->intp_irq, NULL, + anx78xx_intp_threaded_handler, + IRQF_TRIGGER_RISING | IRQF_ONESHOT, + "anx78xx-intp", anx78xx); + if (err) { + DRM_ERROR("Failed to request INTP threaded irq\n"); + goto err_poweroff; + } + + anx78xx->bridge.funcs = &anx78xx_bridge_funcs; + err = drm_bridge_add(&anx78xx->bridge); + if (err < 0) { + DRM_ERROR("Failed to add drm bridge\n"); + goto err_poweroff; + } + + /* If cable is pulled out, just poweroff and wait for hpd event */ + if (!gpiod_get_value(anx78xx->pdata.gpiod_hpd)) + anx78xx_poweroff(anx78xx); + + return 0; + +err_poweroff: + anx78xx_poweroff(anx78xx); + +err_unregister_i2c: + unregister_i2c_dummy_clients(anx78xx); + return err; +} + +static int anx78xx_i2c_remove(struct i2c_client *client) +{ + struct anx78xx *anx78xx = i2c_get_clientdata(client); + + drm_bridge_remove(&anx78xx->bridge); + + unregister_i2c_dummy_clients(anx78xx); + + kfree(anx78xx->edid); + anx78xx->edid = NULL; + + return 0; +} + +static const struct i2c_device_id anx78xx_id[] = { + {"anx7814", 0}, + { /* sentinel */ } +}; + +MODULE_DEVICE_TABLE(i2c, anx78xx_id); + +#if IS_ENABLED(CONFIG_OF) +static const struct of_device_id anx78xx_match_table[] = { + {.compatible = "analogix,anx7814",}, + { /* sentinel */ }, +}; +MODULE_DEVICE_TABLE(of, anx78xx_match_table); +#endif + +static struct i2c_driver anx78xx_driver = { + .driver = { + .name = "anx7814", + .of_match_table = of_match_ptr(anx78xx_match_table), + }, + .probe = anx78xx_i2c_probe, + .remove = anx78xx_i2c_remove, + .id_table = anx78xx_id, +}; + +module_i2c_driver(anx78xx_driver); + +MODULE_DESCRIPTION("ANX78xx SlimPort Transmitter driver"); +MODULE_AUTHOR("Enric Balletbo i Serra enric.balletbo@collabora.com"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/gpu/drm/bridge/anx78xx.h b/drivers/gpu/drm/bridge/anx78xx.h new file mode 100644 index 0000000..38753c8 --- /dev/null +++ b/drivers/gpu/drm/bridge/anx78xx.h @@ -0,0 +1,719 @@ +/* + * Copyright(c) 2016, Analogix Semiconductor. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#ifndef __ANX78xx_H +#define __ANX78xx_H + +#define TX_P0 0x70 +#define TX_P1 0x7a +#define TX_P2 0x72 + +#define RX_P0 0x7e +#define RX_P1 0x80 + +/***************************************************************/ +/* Register definition of device address 0x7e */ +/***************************************************************/ + +/* + * System Control and Status + */ + +/* Software Reset Register 1 */ +#define SP_SOFTWARE_RESET1_REG 0x11 +#define SP_VIDEO_RST BIT(4) +#define SP_HDCP_MAN_RST BIT(2) +#define SP_TMDS_RST BIT(1) +#define SP_SW_MAN_RST BIT(0) + +/* System Status Register */ +#define SP_SYSTEM_STATUS_REG 0x14 +#define SP_TMDS_CLOCK_DET BIT(1) +#define SP_TMDS_DE_DET BIT(0) + +/* HDMI Status Register */ +#define SP_HDMI_STATUS_REG 0x15 +#define SP_HDMI_AUD_LAYOUT BIT(3) +#define SP_HDMI_DET BIT(0) +# define SP_DVI_MODE 0 +# define SP_HDMI_MODE 1 + +/* HDMI Mute Control Register */ +#define SP_HDMI_MUTE_CTRL_REG 0x16 +#define SP_AUD_MUTE BIT(1) +#define SP_VID_MUTE BIT(0) + +/* System Power Down Register 1 */ +#define SP_SYSTEM_POWER_DOWN1_REG 0x18 +#define SP_PWDN_CTRL BIT(0) + +/* + * Audio and Video Auto Control + */ + +/* Auto Audio and Video Control register */ +#define SP_AUDVID_CTRL_REG 0x20 +#define SP_AVC_OE BIT(7) +#define SP_AAC_OE BIT(6) +#define SP_AVC_EN BIT(1) +#define SP_AAC_EN BIT(0) + +/* Audio Exception Enable Registers */ +#define SP_AUD_EXCEPTION_ENABLE_BASE (0x24 - 1) +/* Bits for Audio Exception Enable Register 3 */ +#define SP_AEC_EN21 BIT(5) + +/* + * Interrupt + */ + +/* Interrupt Status Register 1 */ +#define SP_INT_STATUS1_REG 0x31 +/* Bits for Interrupt Status Register 1 */ +#define SP_HDMI_DVI BIT(7) +#define SP_CKDT_CHG BIT(6) +#define SP_SCDT_CHG BIT(5) +#define SP_PCLK_CHG BIT(4) +#define SP_PLL_UNLOCK BIT(3) +#define SP_CABLE_PLUG_CHG BIT(2) +#define SP_SET_MUTE BIT(1) +#define SP_SW_INTR BIT(0) +/* Bits for Interrupt Status Register 2 */ +#define SP_HDCP_ERR BIT(5) +#define SP_AUDIO_SAMPLE_CHG BIT(0) /* undocumented */ +/* Bits for Interrupt Status Register 3 */ +#define SP_AUD_MODE_CHG BIT(0) +/* Bits for Interrupt Status Register 5 */ +#define SP_AUDIO_RCV BIT(0) +/* Bits for Interrupt Status Register 6 */ +#define SP_INT_STATUS6_REG 0x36 +#define SP_CTS_RCV BIT(7) +#define SP_NEW_AUD_PKT BIT(4) +#define SP_NEW_AVI_PKT BIT(1) +#define SP_NEW_CP_PKT BIT(0) +/* Bits for Interrupt Status Register 7 */ +#define SP_NO_VSI BIT(7) +#define SP_NEW_VS BIT(4) + +/* Interrupt Mask 1 Status Registers */ +#define SP_INT_MASK1_REG 0x41 + +/* HDMI US TIMER Control Register */ +#define SP_HDMI_US_TIMER_CTRL_REG 0x49 +#define SP_MS_TIMER_MARGIN_10_8_MASK 0x07 + +/* + * TMDS Control + */ + +/* TMDS Control Registers */ +#define SP_TMDS_CTRL_BASE (0x50 - 1) +/* Bits for TMDS Control Register 7 */ +#define SP_PD_RT BIT(0) + +/* + * Video Control + */ + +/* Video Status Register */ +#define SP_VIDEO_STATUS_REG 0x70 +#define SP_COLOR_DEPTH_MASK 0xf0 +#define SP_COLOR_DEPTH_SHIFT 4 +# define SP_COLOR_DEPTH_MODE_LEGACY 0x00 +# define SP_COLOR_DEPTH_MODE_24BIT 0x04 +# define SP_COLOR_DEPTH_MODE_30BIT 0x05 +# define SP_COLOR_DEPTH_MODE_36BIT 0x06 +# define SP_COLOR_DEPTH_MODE_48BIT 0x07 + +/* Video Data Range Control Register */ +#define SP_VID_DATA_RANGE_CTRL_REG 0x83 +#define SP_R2Y_INPUT_LIMIT BIT(1) + +/* Pixel Clock High Resolution Counter Registers */ +#define SP_PCLK_HIGHRES_CNT_BASE (0x8c - 1) + +/* + * Audio Control + */ + +/* Number of Audio Channels Status Registers */ +#define SP_AUD_CH_STATUS_REG_NUM 6 + +/* Audio IN S/PDIF Channel Status Registers */ +#define SP_AUD_SPDIF_CH_STATUS_BASE 0xc7 + +/* Audio IN S/PDIF Channel Status Register 4 */ +#define SP_FS_FREQ_MASK 0x0f +# define SP_FS_FREQ_44100HZ 0x00 +# define SP_FS_FREQ_48000HZ 0x02 +# define SP_FS_FREQ_32000HZ 0x03 +# define SP_FS_FREQ_88200HZ 0x08 +# define SP_FS_FREQ_96000HZ 0x0a +# define SP_FS_FREQ_176400HZ 0x0c +# define SP_FS_FREQ_192000HZ 0x0e + +/* + * Micellaneous Control Block + */ + +/* CHIP Control Register */ +#define SP_CHIP_CTRL_REG 0xe3 +#define SP_MAN_HDMI5V_DET BIT(3) +#define SP_PLLLOCK_CKDT_EN BIT(2) +#define SP_ANALOG_CKDT_EN BIT(1) +#define SP_DIGITAL_CKDT_EN BIT(0) + +/* Packet Receiving Status Register */ +#define SP_PACKET_RECEIVING_STATUS_REG 0xf3 +#define SP_AVI_RCVD BIT(5) +#define SP_VSI_RCVD BIT(1) + +/***************************************************************/ +/* Register definition of device address 0x80 */ +/***************************************************************/ + +/* HDCP BCAPS Shadow Register */ +#define SP_HDCP_BCAPS_SHADOW_REG 0x2a +#define SP_BCAPS_REPEATER BIT(5) + +/* HDCP Status Register */ +#define SP_RX_HDCP_STATUS_REG 0x3f +#define SP_AUTH_EN BIT(4) + +/* + * InfoFrame and Control Packet Registers + */ + +/* AVI InfoFrame packet checksum */ +#define SP_AVI_INFOFRAME_CHECKSUM 0xa3 + +/* AVI InfoFrame Registers */ +#define SP_AVI_INFOFRAME_DATA_BASE 0xa4 + +#define SP_AVI_COLOR_F_MASK 0x60 +#define SP_AVI_COLOR_F_SHIFT 5 + +/* Audio InfoFrame Registers */ +#define SP_AUD_INFOFRAME_DATA_BASE 0xc4 +#define SP_AUD_INFOFRAME_LAYOUT_MASK 0x0f + +/* MPEG/HDMI Vendor Specific InfoFrame Packet type code */ +#define SP_MPEG_VS_INFOFRAME_TYPE_REG 0xe0 + +/* MPEG/HDMI Vendor Specific InfoFrame Packet length */ +#define SP_MPEG_VS_INFOFRAME_LEN_REG 0xe2 + +/* MPEG/HDMI Vendor Specific InfoFrame Packet version number */ +#define SP_MPEG_VS_INFOFRAME_VER_REG 0xe1 + +/* MPEG/HDMI Vendor Specific InfoFrame Packet content */ +#define SP_MPEG_VS_INFOFRAME_DATA_BASE 0xe4 + +/* General Control Packet Register */ +#define SP_GENERAL_CTRL_PACKET_REG 0x9f +#define SP_CLEAR_AVMUTE BIT(4) +#define SP_SET_AVMUTE BIT(0) + +/***************************************************************/ +/* Register definition of device address 0x70 */ +/***************************************************************/ + +/* HDCP Status Register */ +#define SP_TX_HDCP_STATUS_REG 0x00 +#define SP_AUTH_FAIL BIT(5) +#define SP_AUTHEN_PASS BIT(1) + +/* HDCP Control Register 0 */ +#define SP_HDCP_CTRL0_REG 0x01 +#define SP_RX_REPEATER BIT(6) +#define SP_RE_AUTH BIT(5) +#define SP_SW_AUTH_OK BIT(4) +#define SP_HARD_AUTH_EN BIT(3) +#define SP_HDCP_ENC_EN BIT(2) +#define SP_BKSV_SRM_PASS BIT(1) +#define SP_KSVLIST_VLD BIT(0) +/* HDCP Function Enabled */ +#define SP_HDCP_FUNCTION_ENABLED (BIT(0) | BIT(1) | BIT(2) | BIT(3)) + +/* HDCP Receiver BSTATUS Register 0 */ +#define SP_HDCP_RX_BSTATUS0_REG 0x1b +/* HDCP Receiver BSTATUS Register 1 */ +#define SP_HDCP_RX_BSTATUS1_REG 0x1c + +/* HDCP Embedded "Blue Screen" Content Registers */ +#define SP_HDCP_VID0_BLUE_SCREEN_REG 0x2c +#define SP_HDCP_VID1_BLUE_SCREEN_REG 0x2d +#define SP_HDCP_VID2_BLUE_SCREEN_REG 0x2e + +/* HDCP Wait R0 Timing Register */ +#define SP_HDCP_WAIT_R0_TIME_REG 0x40 + +/* HDCP Link Integrity Check Timer Register */ +#define SP_HDCP_LINK_CHECK_TIMER_REG 0x41 + +/* HDCP Repeater Ready Wait Timer Register */ +#define SP_HDCP_RPTR_RDY_WAIT_TIME_REG 0x42 + +/* HDCP Auto Timer Register */ +#define SP_HDCP_AUTO_TIMER_REG 0x51 + +/* HDCP Key Status Register */ +#define SP_HDCP_KEY_STATUS_REG 0x5e + +/* HDCP Key Command Register */ +#define SP_HDCP_KEY_COMMAND_REG 0x5f +#define SP_DISABLE_SYNC_HDCP BIT(2) + +/* OTP Memory Key Protection Registers */ +#define SP_OTP_KEY_PROTECT1_REG 0x60 +#define SP_OTP_KEY_PROTECT2_REG 0x61 +#define SP_OTP_KEY_PROTECT3_REG 0x62 +#define SP_OTP_PSW1 0xa2 +#define SP_OTP_PSW2 0x7e +#define SP_OTP_PSW3 0xc6 + +/* DP System Control Registers */ +#define SP_DP_SYSTEM_CTRL_BASE (0x80 - 1) +/* Bits for DP System Control Register 2 */ +#define SP_CHA_STA BIT(2) +/* Bits for DP System Control Register 3 */ +#define SP_HPD_STATUS BIT(6) +#define SP_STRM_VALID BIT(2) +/* Bits for DP System Control Register 4 */ +#define SP_ENHANCED_MODE BIT(3) + +/* DP Video Control Register */ +#define SP_DP_VIDEO_CTRL_REG 0x84 +#define SP_COLOR_F_MASK 0x06 +#define SP_COLOR_F_SHIFT 1 +#define SP_BPC_MASK 0xe0 +#define SP_BPC_SHIFT 5 +# define SP_BPC_6BITS 0x00 +# define SP_BPC_8BITS 0x01 +# define SP_BPC_10BITS 0x02 +# define SP_BPC_12BITS 0x03 + +/* DP Audio Control Register */ +#define SP_DP_AUDIO_CTRL_REG 0x87 +#define SP_AUD_EN BIT(0) + +/* 10us Pulse Generate Timer Registers */ +#define SP_I2C_GEN_10US_TIMER0_REG 0x88 +#define SP_I2C_GEN_10US_TIMER1_REG 0x89 + +/* Packet Send Control Register */ +#define SP_PACKET_SEND_CTRL_REG 0x90 +#define SP_AUD_IF_UP BIT(7) +#define SP_AVI_IF_UD BIT(6) +#define SP_MPEG_IF_UD BIT(5) +#define SP_SPD_IF_UD BIT(4) +#define SP_AUD_IF_EN BIT(3) +#define SP_AVI_IF_EN BIT(2) +#define SP_MPEG_IF_EN BIT(1) +#define SP_SPD_IF_EN BIT(0) + +/* DP HDCP Control Register */ +#define SP_DP_HDCP_CTRL_REG 0x92 +#define SP_AUTO_EN BIT(7) +#define SP_AUTO_START BIT(5) +#define SP_LINK_POLLING BIT(1) + +/* DP Main Link Bandwidth Setting Register */ +#define SP_DP_MAIN_LINK_BW_SET_REG 0xa0 +#define SP_LINK_BW_SET_MASK 0x1f +#define SP_INITIAL_SLIM_M_AUD_SEL BIT(5) + +/* DP Training Pattern Set Register */ +#define SP_DP_TRAINING_PATTERN_SET_REG 0xa2 + +/* DP Lane 0 Link Training Control Register */ +#define SP_DP_LANE0_LT_CTRL_REG 0xa3 +#define SP_TX_SW_SET_MASK 0x1b +#define SP_MAX_PRE_REACH BIT(5) +#define SP_MAX_DRIVE_REACH BIT(4) +#define SP_PRE_EMP_LEVEL1 BIT(3) +#define SP_DRVIE_CURRENT_LEVEL1 BIT(0) + +/* DP Link Training Control Register */ +#define SP_DP_LT_CTRL_REG 0xa8 +#define SP_LT_ERROR_TYPE_MASK 0x70 +# define SP_LT_NO_ERROR 0x00 +# define SP_LT_AUX_WRITE_ERROR 0x01 +# define SP_LT_MAX_DRIVE_REACHED 0x02 +# define SP_LT_WRONG_LANE_COUNT_SET 0x03 +# define SP_LT_LOOP_SAME_5_TIME 0x04 +# define SP_LT_CR_FAIL_IN_EQ 0x05 +# define SP_LT_EQ_LOOP_5_TIME 0x06 +#define SP_LT_EN BIT(0) + +/* DP CEP Training Control Registers */ +#define SP_DP_CEP_TRAINING_CTRL0_REG 0xa9 +#define SP_DP_CEP_TRAINING_CTRL1_REG 0xaa + +/* DP Debug Register 1 */ +#define SP_DP_DEBUG1_REG 0xb0 +#define SP_DEBUG_PLL_LOCK BIT(4) +#define SP_POLLING_EN BIT(1) + +/* DP Polling Control Register */ +#define SP_DP_POLLING_CTRL_REG 0xb4 +#define SP_AUTO_POLLING_DISABLE BIT(0) + +/* DP Link Debug Control Register */ +#define SP_DP_LINK_DEBUG_CTRL_REG 0xb8 +#define SP_M_VID_DEBUG BIT(5) +#define SP_NEW_PRBS7 BIT(4) +#define SP_INSERT_ER BIT(1) +#define SP_PRBS31_EN BIT(0) + +/* AUX Misc control Register */ +#define SP_AUX_MISC_CTRL_REG 0xbf + +/* DP PLL control Register */ +#define SP_DP_PLL_CTRL_REG 0xc7 +#define SP_PLL_RST BIT(6) + +/* DP Analog Power Down Register */ +#define SP_DP_ANALOG_POWER_DOWN_REG 0xc8 +#define SP_CH0_PD BIT(0) + +/* DP Misc Control Register */ +#define SP_DP_MISC_CTRL_REG 0xcd +#define SP_EQ_TRAINING_LOOP BIT(6) + +/* DP Extra I2C Device Address Register */ +#define SP_DP_EXTRA_I2C_DEV_ADDR_REG 0xce +#define SP_I2C_STRETCH_DISABLE BIT(7) + +#define SP_I2C_EXTRA_ADDR 0x50 + +/* DP Downspread Control Register 1 */ +#define SP_DP_DOWNSPREAD_CTRL1_REG 0xd0 + +/* DP M Value Calculation Control Register */ +#define SP_DP_M_CALCULATION_CTRL_REG 0xd9 +#define SP_M_GEN_CLK_SEL BIT(0) + +/* AUX Channel Access Status Register */ +#define SP_AUX_CH_STATUS_REG 0xe0 +#define SP_AUX_STATUS 0x0f + +/* AUX Channel DEFER Control Register */ +#define SP_AUX_DEFER_CTRL_REG 0xe2 +#define SP_DEFER_CTRL_EN BIT(7) + +/* DP Buffer Data Count Register */ +#define SP_BUF_DATA_COUNT_REG 0xe4 +#define SP_BUF_DATA_COUNT_MASK 0x1f +#define SP_BUF_CLR BIT(7) + +/* DP AUX Channel Control Register 1 */ +#define SP_DP_AUX_CH_CTRL1_REG 0xe5 +#define SP_AUX_TX_COMM_MASK 0x0f +#define SP_AUX_LENGTH_MASK 0xf0 +#define SP_AUX_LENGTH_SHIFT 4 + +/* DP AUX CH Address Register 0 */ +#define SP_AUX_ADDR_7_0_REG 0xe6 + +/* DP AUX CH Address Register 1 */ +#define SP_AUX_ADDR_15_8_REG 0xe7 + +/* DP AUX CH Address Register 2 */ +#define SP_AUX_ADDR_19_16_REG 0xe8 +#define SP_AUX_ADDR_19_16_MASK 0x0f + +/* DP AUX Channel Control Register 2 */ +#define SP_DP_AUX_CH_CTRL2_REG 0xe9 +#define SP_AUX_SEL_RXCM BIT(6) +#define SP_AUX_CHSEL BIT(3) +#define SP_AUX_PN_INV BIT(2) +#define SP_ADDR_ONLY BIT(1) +#define SP_AUX_EN BIT(0) + +/* DP Video Stream Control InfoFrame Register */ +#define SP_DP_3D_VSC_CTRL_REG 0xea +#define SP_INFO_FRAME_VSC_EN BIT(0) + +/* DP Video Stream Data Byte 1 Register */ +#define SP_DP_VSC_DB1_REG 0xeb + +/* DP AUX Channel Control Register 3 */ +#define SP_DP_AUX_CH_CTRL3_REG 0xec +#define SP_WAIT_COUNTER_7_0_MASK 0xff + +/* DP AUX Channel Control Register 4 */ +#define SP_DP_AUX_CH_CTRL4_REG 0xed + +/* DP AUX Buffer Data Registers */ +#define SP_DP_BUF_DATA0_REG 0xf0 + +/***************************************************************/ +/* Register definition of device address 0x72 */ +/***************************************************************/ + +/* + * Core Register Definitions + */ + +/* Device ID Low Byte Register */ +#define SP_DEVICE_IDL_REG 0x02 + +/* Device ID High Byte Register */ +#define SP_DEVICE_IDH_REG 0x03 + +/* Device version register */ +#define SP_DEVICE_VERSION_REG 0x04 + +/* Power Down Control Register */ +#define SP_POWERDOWN_CTRL_REG 0x05 +#define SP_REGISTER_PD BIT(7) +#define SP_HDCP_PD BIT(5) +#define SP_AUDIO_PD BIT(4) +#define SP_VIDEO_PD BIT(3) +#define SP_LINK_PD BIT(2) +#define SP_TOTAL_PD BIT(1) + +/* Reset Control Register 1 */ +#define SP_RESET_CTRL1_REG 0x06 +#define SP_MISC_RST BIT(7) +#define SP_VIDCAP_RST BIT(6) +#define SP_VIDFIF_RST BIT(5) +#define SP_AUDFIF_RST BIT(4) +#define SP_AUDCAP_RST BIT(3) +#define SP_HDCP_RST BIT(2) +#define SP_SW_RST BIT(1) +#define SP_HW_RST BIT(0) + +/* Reset Control Register 2 */ +#define SP_RESET_CTRL2_REG 0x07 +#define SP_AUX_RST BIT(2) +#define SP_SERDES_FIFO_RST BIT(1) +#define SP_I2C_REG_RST BIT(0) + +/* Video Control Register 1 */ +#define SP_VID_CTRL1_REG 0x08 +#define SP_VIDEO_EN BIT(7) +#define SP_VIDEO_MUTE BIT(2) +#define SP_DE_GEN BIT(1) +#define SP_DEMUX BIT(0) + +/* Video Control Register 2 */ +#define SP_VID_CTRL2_REG 0x09 +#define SP_IN_COLOR_F_MASK 0x03 +#define SP_IN_YC_BIT_SEL BIT(2) +#define SP_IN_BPC_MASK 0x70 +#define SP_IN_BPC_SHIFT 4 +# define SP_IN_BPC_12BIT 0x03 +# define SP_IN_BPC_10BIT 0x02 +# define SP_IN_BPC_8BIT 0x01 +# define SP_IN_BPC_6BIT 0x00 +#define SP_IN_D_RANGE BIT(7) + +/* Video Control Register 3 */ +#define SP_VID_CTRL3_REG 0x0a +#define SP_HPD_OUT BIT(6) + +/* Video Control Register 5 */ +#define SP_VID_CTRL5_REG 0x0c +#define SP_CSC_STD_SEL BIT(7) +#define SP_XVYCC_RNG_LMT BIT(6) +#define SP_RANGE_Y2R BIT(5) +#define SP_CSPACE_Y2R BIT(4) +#define SP_RGB_RNG_LMT BIT(3) +#define SP_Y_RNG_LMT BIT(2) +#define SP_RANGE_R2Y BIT(1) +#define SP_CSPACE_R2Y BIT(0) + +/* Video Control Register 6 */ +#define SP_VID_CTRL6_REG 0x0d +#define SP_TEST_PATTERN_EN BIT(7) +#define SP_VIDEO_PROCESS_EN BIT(6) +#define SP_VID_US_MODE BIT(3) +#define SP_VID_DS_MODE BIT(2) +#define SP_UP_SAMPLE BIT(1) +#define SP_DOWN_SAMPLE BIT(0) + +/* Video Control Register 8 */ +#define SP_VID_CTRL8_REG 0x0f +#define SP_VID_VRES_TH BIT(0) + +/* Total Line Status Low Byte Register */ +#define SP_TOTAL_LINE_STAL_REG 0x24 + +/* Total Line Status High Byte Register */ +#define SP_TOTAL_LINE_STAH_REG 0x25 + +/* Active Line Status Low Byte Register */ +#define SP_ACT_LINE_STAL_REG 0x26 + +/* Active Line Status High Byte Register */ +#define SP_ACT_LINE_STAH_REG 0x27 + +/* Vertical Front Porch Status Register */ +#define SP_V_F_PORCH_STA_REG 0x28 + +/* Vertical SYNC Width Status Register */ +#define SP_V_SYNC_STA_REG 0x29 + +/* Vertical Back Porch Status Register */ +#define SP_V_B_PORCH_STA_REG 0x2a + +/* Total Pixel Status Low Byte Register */ +#define SP_TOTAL_PIXEL_STAL_REG 0x2b + +/* Total Pixel Status High Byte Register */ +#define SP_TOTAL_PIXEL_STAH_REG 0x2c + +/* Active Pixel Status Low Byte Register */ +#define SP_ACT_PIXEL_STAL_REG 0x2d + +/* Active Pixel Status High Byte Register */ +#define SP_ACT_PIXEL_STAH_REG 0x2e + +/* Horizontal Front Porch Status Low Byte Register */ +#define SP_H_F_PORCH_STAL_REG 0x2f + +/* Horizontal Front Porch Statys High Byte Register */ +#define SP_H_F_PORCH_STAH_REG 0x30 + +/* Horizontal SYNC Width Status Low Byte Register */ +#define SP_H_SYNC_STAL_REG 0x31 + +/* Horizontal SYNC Width Status High Byte Register */ +#define SP_H_SYNC_STAH_REG 0x32 + +/* Horizontal Back Porch Status Low Byte Register */ +#define SP_H_B_PORCH_STAL_REG 0x33 + +/* Horizontal Back Porch Status High Byte Register */ +#define SP_H_B_PORCH_STAH_REG 0x34 + +/* InfoFrame AVI Packet DB1 Register */ +#define SP_INFOFRAME_AVI_DB1_REG 0x70 + +/* Bit Control Specific Register */ +#define SP_BIT_CTRL_SPECIFIC_REG 0x80 +#define SP_BIT_CTRL_SELECT_SHIFT 1 +#define SP_ENABLE_BIT_CTRL BIT(0) + +/* InfoFrame Audio Packet DB1 Register */ +#define SP_INFOFRAME_AUD_DB1_REG 0x83 + +/* InfoFrame MPEG Packet DB1 Register */ +#define SP_INFOFRAME_MPEG_DB1_REG 0xb0 + +/* Audio Channel Status Registers */ +#define SP_AUD_CH_STATUS_BASE 0xd0 + +/* Audio Channel Num Register 5 */ +#define SP_I2S_CHANNEL_NUM_MASK 0xe0 +# define SP_I2S_CH_NUM_1 (0x00 << 5) +# define SP_I2S_CH_NUM_2 (0x01 << 5) +# define SP_I2S_CH_NUM_3 (0x02 << 5) +# define SP_I2S_CH_NUM_4 (0x03 << 5) +# define SP_I2S_CH_NUM_5 (0x04 << 5) +# define SP_I2S_CH_NUM_6 (0x05 << 5) +# define SP_I2S_CH_NUM_7 (0x06 << 5) +# define SP_I2S_CH_NUM_8 (0x07 << 5) +#define SP_EXT_VUCP BIT(2) +#define SP_VBIT BIT(1) +#define SP_AUDIO_LAYOUT BIT(0) + +/* Analog Debug Register 2 */ +#define SP_ANALOG_DEBUG2_REG 0xdd +#define SP_FORCE_SW_OFF_BYPASS 0x20 +#define SP_XTAL_FRQ 0x1c +# define SP_XTAL_FRQ_19M2 (0x00 << 2) +# define SP_XTAL_FRQ_24M (0x01 << 2) +# define SP_XTAL_FRQ_25M (0x02 << 2) +# define SP_XTAL_FRQ_26M (0x03 << 2) +# define SP_XTAL_FRQ_27M (0x04 << 2) +# define SP_XTAL_FRQ_38M4 (0x05 << 2) +# define SP_XTAL_FRQ_52M (0x06 << 2) +#define SP_POWERON_TIME_1P5MS 0x03 + +/* Analog Control 0 Register */ +#define SP_ANALOG_CTRL0_REG 0xe1 + +/* Common Interrupt Status Register 1 */ +#define SP_COMMON_INT_STATUS_BASE (0xf1 - 1) +#define SP_PLL_LOCK_CHG 0x40 + +/* Common Interrupt Status Register 2 */ +#define SP_COMMON_INT_STATUS2 0xf2 +#define SP_HDCP_AUTH_CHG BIT(1) +#define SP_HDCP_AUTH_DONE BIT(0) + +#define SP_HDCP_LINK_CHECK_FAIL BIT(0) + +/* Common Interrupt Status Register 4 */ +#define SP_COMMON_INT_STATUS4_REG 0xf4 +#define SP_HPD_IRQ BIT(6) +#define SP_HPD_ESYNC_ERR BIT(4) +#define SP_HPD_CHG BIT(2) +#define SP_HPD_LOST BIT(1) +#define SP_HPD_PLUG BIT(0) + +/* DP Interrupt Status Register */ +#define SP_DP_INT_STATUS1_REG 0xf7 +#define SP_TRAINING_FINISH BIT(5) +#define SP_POLLING_ERR BIT(4) + +/* Common Interrupt Mask Register */ +#define SP_COMMON_INT_MASK_BASE (0xf8 - 1) + +#define SP_COMMON_INT_MASK4_REG 0xfb + +/* DP Interrupts Mask Register */ +#define SP_DP_INT_MASK1_REG 0xfe + +/* Interrupt Control Register */ +#define SP_INT_CTRL_REG 0xff + +/***************************************************************/ +/* Register definition of device address 0x7a */ +/***************************************************************/ + +/* DP TX Link Training Control Register */ +#define SP_DP_TX_LT_CTRL0_REG 0x30 + +/* PD 1.2 Lint Training 80bit Pattern Register */ +#define SP_DP_LT_80BIT_PATTERN0_REG 0x80 +#define SP_DP_LT_80BIT_PATTERN_REG_NUM 10 + +/* Audio Interface Control Register 0 */ +#define SP_AUD_INTERFACE_CTRL0_REG 0x5f +#define SP_AUD_INTERFACE_DISABLE 0x80 + +/* Audio Interface Control Register 2 */ +#define SP_AUD_INTERFACE_CTRL2_REG 0x60 +#define SP_M_AUD_ADJUST_ST 0x04 + +/* Audio Interface Control Register 3 */ +#define SP_AUD_INTERFACE_CTRL3_REG 0x62 + +/* Audio Interface Control Register 4 */ +#define SP_AUD_INTERFACE_CTRL4_REG 0x67 + +/* Audio Interface Control Register 5 */ +#define SP_AUD_INTERFACE_CTRL5_REG 0x68 + +/* Audio Interface Control Register 6 */ +#define SP_AUD_INTERFACE_CTRL6_REG 0x69 + +/* Firmware Version Register */ +#define SP_FW_VER_REG 0xb7 + +#endif