This adds a new device tree binding for Sitronix ST7735R display panels, such as the Adafruit 1.8" TFT.

Signed-off-by: David Lechner david@lechnology.com Reviewed-by: Rob Herring robh@kernel.org ---

v4 changes: * none

v3 changes: * compatible string is changed from "sitronix,st7735r-jd-t18003-t01" to "jianda,jd-t18003-t01", "sitronix,st7735r"

v2 changes: * none

.../bindings/display/sitronix,st7735r.txt | 35 ++++++++++++++++++++++ 1 file changed, 35 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/sitronix,st7735r.txt

diff --git a/Documentation/devicetree/bindings/display/sitronix,st7735r.txt b/Documentation/devicetree/bindings/display/sitronix,st7735r.txt new file mode 100644 index 0000000..f0a5090 --- /dev/null +++ b/Documentation/devicetree/bindings/display/sitronix,st7735r.txt @@ -0,0 +1,35 @@ +Sitronix ST7735R display panels + +This binding is for display panels using a Sitronix ST7735R controller in SPI +mode. + +Required properties: +- compatible: "jianda,jd-t18003-t01", "sitronix,st7735r" +- dc-gpios: Display data/command selection (D/CX) +- reset-gpios: Reset signal (RSTX) + +The node for this driver must be a child node of a SPI controller, hence +all mandatory properties described in ../spi/spi-bus.txt must be specified. + +Optional properties: +- rotation: panel rotation in degrees counter clockwise (0,90,180,270) +- backlight: phandle of the backlight device attached to the panel + +Example: + + backlight: backlight { + compatible = "gpio-backlight"; + gpios = <&gpio 44 GPIO_ACTIVE_HIGH>; + } + + ... + + display@0{ + compatible = "jianda,jd-t18003-t01", "sitronix,st7735r"; + reg = <0>; + spi-max-frequency = <32000000>; + dc-gpios = <&gpio 43 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio 80 GPIO_ACTIVE_HIGH>; + rotation = <270>; + backlight = &backlight; + };

This adds a new driver for Sitronix ST7735R display panels.

This has been tested using an Adafruit 1.8" TFT.

Signed-off-by: David Lechner david@lechnology.com Reviewed-by: Noralf Trønnes noralf@tronnes.org ---

v4 changes: * renamed st7735r_pipe_enable to jd_t18003_t01_pipe_enable * renamed st7735r_pipe_funcs to jd_t18003_t01_pipe_funcs * changed gamma curve to one from Adafruit's Arduino library

v3 changes: * Changed compatible string * use SPDX license header * Renamed mode struct to use panel name instead of controller name

v2 changes: * Change delay from 10ms to 20ms to avoid checkpatch warning * Use mipi_dbi_pipe_enable()/mipi_dbi_pipe_disable() to reduce duplicated code * Rebase on drm-misc-next (tinydrm_lastclose => drm_fb_helper_lastclose) * Use mipi_dbi_debugfs_init * Add mipi->read_commands = NULL; since this display is write-only

MAINTAINERS | 6 ++ drivers/gpu/drm/tinydrm/Kconfig | 10 ++ drivers/gpu/drm/tinydrm/Makefile | 1 + drivers/gpu/drm/tinydrm/st7735r.c | 215 ++++++++++++++++++++++++++++++++++++++ 4 files changed, 232 insertions(+) create mode 100644 drivers/gpu/drm/tinydrm/st7735r.c

diff --git a/MAINTAINERS b/MAINTAINERS index 528e223..b4ffbc2 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -4556,6 +4556,12 @@ S: Maintained F: drivers/gpu/drm/tinydrm/st7586.c F: Documentation/devicetree/bindings/display/st7586.txt

+DRM DRIVER FOR SITRONIX ST7735R PANELS +M: David Lechner david@lechnology.com +S: Maintained +F: drivers/gpu/drm/tinydrm/st7735r.c +F: Documentation/devicetree/bindings/display/st7735r.txt + DRM DRIVER FOR TDFX VIDEO CARDS S: Orphan / Obsolete F: drivers/gpu/drm/tdfx/ diff --git a/drivers/gpu/drm/tinydrm/Kconfig b/drivers/gpu/drm/tinydrm/Kconfig index 90c5bd5..b0e567d 100644 --- a/drivers/gpu/drm/tinydrm/Kconfig +++ b/drivers/gpu/drm/tinydrm/Kconfig @@ -52,3 +52,13 @@ config TINYDRM_ST7586 * LEGO MINDSTORMS EV3

If M is selected the module will be called st7586. + +config TINYDRM_ST7735R + tristate "DRM support for Sitronix ST7735R display panels" + depends on DRM_TINYDRM && SPI + select TINYDRM_MIPI_DBI + help + DRM driver Sitronix ST7735R with one of the following LCDs: + * JD-T18003-T01 1.8" 128x160 TFT + + If M is selected the module will be called st7735r. diff --git a/drivers/gpu/drm/tinydrm/Makefile b/drivers/gpu/drm/tinydrm/Makefile index 8aeee53..49a1119 100644 --- a/drivers/gpu/drm/tinydrm/Makefile +++ b/drivers/gpu/drm/tinydrm/Makefile @@ -8,3 +8,4 @@ obj-$(CONFIG_TINYDRM_ILI9225) += ili9225.o obj-$(CONFIG_TINYDRM_MI0283QT) += mi0283qt.o obj-$(CONFIG_TINYDRM_REPAPER) += repaper.o obj-$(CONFIG_TINYDRM_ST7586) += st7586.o +obj-$(CONFIG_TINYDRM_ST7735R) += st7735r.o diff --git a/drivers/gpu/drm/tinydrm/st7735r.c b/drivers/gpu/drm/tinydrm/st7735r.c new file mode 100644 index 0000000..98ff447 --- /dev/null +++ b/drivers/gpu/drm/tinydrm/st7735r.c @@ -0,0 +1,215 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * DRM driver for Sitronix ST7735R panels + * + * Copyright 2017 David Lechner david@lechnology.com + */ + +#include <linux/delay.h> +#include <linux/dma-buf.h> +#include <linux/gpio/consumer.h> +#include <linux/module.h> +#include <linux/property.h> +#include <linux/spi/spi.h> +#include <video/mipi_display.h> + +#include <drm/drm_fb_helper.h> +#include <drm/drm_gem_framebuffer_helper.h> +#include <drm/tinydrm/mipi-dbi.h> +#include <drm/tinydrm/tinydrm-helpers.h> + +#define ST7735R_FRMCTR1 0xb1 +#define ST7735R_FRMCTR2 0xb2 +#define ST7735R_FRMCTR3 0xb3 +#define ST7735R_INVCTR 0xb4 +#define ST7735R_PWCTR1 0xc0 +#define ST7735R_PWCTR2 0xc1 +#define ST7735R_PWCTR3 0xc2 +#define ST7735R_PWCTR4 0xc3 +#define ST7735R_PWCTR5 0xc4 +#define ST7735R_VMCTR1 0xc5 +#define ST7735R_GAMCTRP1 0xe0 +#define ST7735R_GAMCTRN1 0xe1 + +#define ST7735R_MY BIT(7) +#define ST7735R_MX BIT(6) +#define ST7735R_MV BIT(5) + +static void jd_t18003_t01_pipe_enable(struct drm_simple_display_pipe *pipe, + struct drm_crtc_state *crtc_state) +{ + struct tinydrm_device *tdev = pipe_to_tinydrm(pipe); + struct mipi_dbi *mipi = mipi_dbi_from_tinydrm(tdev); + struct device *dev = tdev->drm->dev; + int ret; + u8 addr_mode; + + DRM_DEBUG_KMS("\n"); + + mipi_dbi_hw_reset(mipi); + + ret = mipi_dbi_command(mipi, MIPI_DCS_SOFT_RESET); + if (ret) { + DRM_DEV_ERROR(dev, "Error sending command %d\n", ret); + return; + } + + msleep(150); + + mipi_dbi_command(mipi, MIPI_DCS_EXIT_SLEEP_MODE); + msleep(500); + + mipi_dbi_command(mipi, ST7735R_FRMCTR1, 0x01, 0x2c, 0x2d); + mipi_dbi_command(mipi, ST7735R_FRMCTR2, 0x01, 0x2c, 0x2d); + mipi_dbi_command(mipi, ST7735R_FRMCTR3, 0x01, 0x2c, 0x2d, 0x01, 0x2c, + 0x2d); + mipi_dbi_command(mipi, ST7735R_INVCTR, 0x07); + mipi_dbi_command(mipi, ST7735R_PWCTR1, 0xa2, 0x02, 0x84); + mipi_dbi_command(mipi, ST7735R_PWCTR2, 0xc5); + mipi_dbi_command(mipi, ST7735R_PWCTR3, 0x0a, 0x00); + mipi_dbi_command(mipi, ST7735R_PWCTR4, 0x8a, 0x2a); + mipi_dbi_command(mipi, ST7735R_PWCTR5, 0x8a, 0xee); + mipi_dbi_command(mipi, ST7735R_VMCTR1, 0x0e); + mipi_dbi_command(mipi, MIPI_DCS_EXIT_INVERT_MODE); + switch (mipi->rotation) { + default: + addr_mode = ST7735R_MX | ST7735R_MY; + break; + case 90: + addr_mode = ST7735R_MX | ST7735R_MV; + break; + case 180: + addr_mode = 0; + break; + case 270: + addr_mode = ST7735R_MY | ST7735R_MV; + break; + } + mipi_dbi_command(mipi, MIPI_DCS_SET_ADDRESS_MODE, addr_mode); + mipi_dbi_command(mipi, MIPI_DCS_SET_PIXEL_FORMAT, + MIPI_DCS_PIXEL_FMT_16BIT); + mipi_dbi_command(mipi, ST7735R_GAMCTRP1, 0x02, 0x1c, 0x07, 0x12, 0x37, + 0x32, 0x29, 0x2d, 0x29, 0x25, 0x2b, 0x39, 0x00, 0x01, + 0x03, 0x10); + mipi_dbi_command(mipi, ST7735R_GAMCTRN1, 0x03, 0x1d, 0x07, 0x06, 0x2e, + 0x2c, 0x29, 0x2d, 0x2e, 0x2e, 0x37, 0x3f, 0x00, 0x00, + 0x02, 0x10); + mipi_dbi_command(mipi, MIPI_DCS_SET_DISPLAY_ON); + + msleep(100); + + mipi_dbi_command(mipi, MIPI_DCS_ENTER_NORMAL_MODE); + + msleep(20); + + mipi_dbi_pipe_enable(pipe, crtc_state); +} + +static const struct drm_simple_display_pipe_funcs jd_t18003_t01_pipe_funcs = { + .enable = jd_t18003_t01_pipe_enable, + .disable = mipi_dbi_pipe_disable, + .update = tinydrm_display_pipe_update, + .prepare_fb = tinydrm_display_pipe_prepare_fb, +}; + +static const struct drm_display_mode jd_t18003_t01_mode = { + TINYDRM_MODE(128, 160, 28, 35), +}; + +DEFINE_DRM_GEM_CMA_FOPS(st7735r_fops); + +static struct drm_driver st7735r_driver = { + .driver_features = DRIVER_GEM | DRIVER_MODESET | DRIVER_PRIME | + DRIVER_ATOMIC, + .fops = &st7735r_fops, + TINYDRM_GEM_DRIVER_OPS, + .lastclose = drm_fb_helper_lastclose, + .debugfs_init = mipi_dbi_debugfs_init, + .name = "st7735r", + .desc = "Sitronix ST7735R", + .date = "20171128", + .major = 1, + .minor = 0, +}; + +static const struct of_device_id st7735r_of_match[] = { + { .compatible = "jianda,jd-t18003-t01" }, + { }, +}; +MODULE_DEVICE_TABLE(of, st7735r_of_match); + +static const struct spi_device_id st7735r_id[] = { + { "jd-t18003-t01", 0 }, + { }, +}; +MODULE_DEVICE_TABLE(spi, st7735r_id); + +static int st7735r_probe(struct spi_device *spi) +{ + struct device *dev = &spi->dev; + struct mipi_dbi *mipi; + struct gpio_desc *dc; + u32 rotation = 0; + int ret; + + mipi = devm_kzalloc(dev, sizeof(*mipi), GFP_KERNEL); + if (!mipi) + return -ENOMEM; + + mipi->reset = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH); + if (IS_ERR(mipi->reset)) { + DRM_DEV_ERROR(dev, "Failed to get gpio 'reset'\n"); + return PTR_ERR(mipi->reset); + } + + dc = devm_gpiod_get(dev, "dc", GPIOD_OUT_LOW); + if (IS_ERR(dc)) { + DRM_DEV_ERROR(dev, "Failed to get gpio 'dc'\n"); + return PTR_ERR(dc); + } + + mipi->backlight = tinydrm_of_find_backlight(dev); + if (IS_ERR(mipi->backlight)) + return PTR_ERR(mipi->backlight); + + device_property_read_u32(dev, "rotation", &rotation); + + ret = mipi_dbi_spi_init(spi, mipi, dc); + if (ret) + return ret; + + /* Cannot read from Adafruit 1.8" display via SPI */ + mipi->read_commands = NULL; + + ret = mipi_dbi_init(&spi->dev, mipi, &jd_t18003_t01_pipe_funcs, + &st7735r_driver, &jd_t18003_t01_mode, rotation); + if (ret) + return ret; + + spi_set_drvdata(spi, mipi); + + return devm_tinydrm_register(&mipi->tinydrm); +} + +static void st7735r_shutdown(struct spi_device *spi) +{ + struct mipi_dbi *mipi = spi_get_drvdata(spi); + + tinydrm_shutdown(&mipi->tinydrm); +} + +static struct spi_driver st7735r_spi_driver = { + .driver = { + .name = "st7735r", + .owner = THIS_MODULE, + .of_match_table = st7735r_of_match, + }, + .id_table = st7735r_id, + .probe = st7735r_probe, + .shutdown = st7735r_shutdown, +}; +module_spi_driver(st7735r_spi_driver); + +MODULE_DESCRIPTION("Sitronix ST7735R DRM driver"); +MODULE_AUTHOR("David Lechner david@lechnology.com"); +MODULE_LICENSE("GPL");