The mode_config max_width/max_height determines the maximum framebuffer size the pixel reader can handle. But the values were set thinking they were determining the maximum screen dimensions.
This patch changes the values to the maximum height/width the CANVAS block can handle rounded to some coherent values.
Fixes: a41e82e6c457 ("drm/meson: Add support for components") Signed-off-by: Neil Armstrong narmstrong@baylibre.com --- drivers/gpu/drm/meson/meson_drv.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/meson/meson_drv.c b/drivers/gpu/drm/meson/meson_drv.c index d344312..2e29968 100644 --- a/drivers/gpu/drm/meson/meson_drv.c +++ b/drivers/gpu/drm/meson/meson_drv.c @@ -243,8 +243,8 @@ static int meson_drv_bind_master(struct device *dev, bool has_components) goto free_drm;
drm_mode_config_init(drm); - drm->mode_config.max_width = 3840; - drm->mode_config.max_height = 2160; + drm->mode_config.max_width = 16384; + drm->mode_config.max_height = 8192; drm->mode_config.funcs = &meson_mode_config_funcs;
/* Hardware Initialization */
On Thu, Oct 04, 2018 at 10:42:43AM +0200, Neil Armstrong wrote:
The mode_config max_width/max_height determines the maximum framebuffer size the pixel reader can handle. But the values were set thinking they were determining the maximum screen dimensions.
This patch changes the values to the maximum height/width the CANVAS block can handle rounded to some coherent values.
Fixes: a41e82e6c457 ("drm/meson: Add support for components") Signed-off-by: Neil Armstrong narmstrong@baylibre.com
It's both. Grep for all the callers of ->fill_modes and you'll see that this limit is also used to filter max screen sizes.
If you want to change this, then I think we need a new mode_config.fb_max_width/height, which if non-zero, would extend the limit for fbs.
There's also the problem that if you extend this for fbs, then there's no check anymore in the atomic_commit paths (or legacy modeset), so that needs to be addressed somehow too.
Bunch of igt to make sure we're not missing anything would be sweet on top, e.g. e.g. trying to set a mode over the limit and making sure it fails.
Cheers, Daniel
drivers/gpu/drm/meson/meson_drv.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/meson/meson_drv.c b/drivers/gpu/drm/meson/meson_drv.c index d344312..2e29968 100644 --- a/drivers/gpu/drm/meson/meson_drv.c +++ b/drivers/gpu/drm/meson/meson_drv.c @@ -243,8 +243,8 @@ static int meson_drv_bind_master(struct device *dev, bool has_components) goto free_drm;
drm_mode_config_init(drm);
- drm->mode_config.max_width = 3840;
- drm->mode_config.max_height = 2160;
drm->mode_config.max_width = 16384;
drm->mode_config.max_height = 8192; drm->mode_config.funcs = &meson_mode_config_funcs;
/* Hardware Initialization */
-- 2.7.4
dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel
On 04/10/2018 12:09, Daniel Vetter wrote:
On Thu, Oct 04, 2018 at 10:42:43AM +0200, Neil Armstrong wrote:
The mode_config max_width/max_height determines the maximum framebuffer size the pixel reader can handle. But the values were set thinking they were determining the maximum screen dimensions.
This patch changes the values to the maximum height/width the CANVAS block can handle rounded to some coherent values.
Fixes: a41e82e6c457 ("drm/meson: Add support for components") Signed-off-by: Neil Armstrong narmstrong@baylibre.com
It's both. Grep for all the callers of ->fill_modes and you'll see that this limit is also used to filter max screen sizes.
If you want to change this, then I think we need a new mode_config.fb_max_width/height, which if non-zero, would extend the limit for fbs.
There's also the problem that if you extend this for fbs, then there's no check anymore in the atomic_commit paths (or legacy modeset), so that needs to be addressed somehow too.
What about adding optionals mode_config.fb_max_width/height and update drm_internal_framebuffer_create() to use these if non-0 or fallback to the mode_config max_width/max_height.
Neil
Bunch of igt to make sure we're not missing anything would be sweet on top, e.g. e.g. trying to set a mode over the limit and making sure it fails.
Cheers, Daniel
drivers/gpu/drm/meson/meson_drv.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/meson/meson_drv.c b/drivers/gpu/drm/meson/meson_drv.c index d344312..2e29968 100644 --- a/drivers/gpu/drm/meson/meson_drv.c +++ b/drivers/gpu/drm/meson/meson_drv.c @@ -243,8 +243,8 @@ static int meson_drv_bind_master(struct device *dev, bool has_components) goto free_drm;
drm_mode_config_init(drm);
- drm->mode_config.max_width = 3840;
- drm->mode_config.max_height = 2160;
drm->mode_config.max_width = 16384;
drm->mode_config.max_height = 8192; drm->mode_config.funcs = &meson_mode_config_funcs;
/* Hardware Initialization */
-- 2.7.4
dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel
On Thu, Oct 4, 2018 at 5:05 PM Neil Armstrong narmstrong@baylibre.com wrote:
On 04/10/2018 12:09, Daniel Vetter wrote:
On Thu, Oct 04, 2018 at 10:42:43AM +0200, Neil Armstrong wrote:
The mode_config max_width/max_height determines the maximum framebuffer size the pixel reader can handle. But the values were set thinking they were determining the maximum screen dimensions.
This patch changes the values to the maximum height/width the CANVAS block can handle rounded to some coherent values.
Fixes: a41e82e6c457 ("drm/meson: Add support for components") Signed-off-by: Neil Armstrong narmstrong@baylibre.com
It's both. Grep for all the callers of ->fill_modes and you'll see that this limit is also used to filter max screen sizes.
If you want to change this, then I think we need a new mode_config.fb_max_width/height, which if non-zero, would extend the limit for fbs.
There's also the problem that if you extend this for fbs, then there's no check anymore in the atomic_commit paths (or legacy modeset), so that needs to be addressed somehow too.
What about adding optionals mode_config.fb_max_width/height and update drm_internal_framebuffer_create() to use these if non-0 or fallback to the mode_config max_width/max_height.
That's what I meant. Except you also need to then fix the gap you've opened in atomic_check, and validate the mode size against mode_config.max_width/height. -Daniel
Neil
Bunch of igt to make sure we're not missing anything would be sweet on top, e.g. e.g. trying to set a mode over the limit and making sure it fails.
Cheers, Daniel
drivers/gpu/drm/meson/meson_drv.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/meson/meson_drv.c b/drivers/gpu/drm/meson/meson_drv.c index d344312..2e29968 100644 --- a/drivers/gpu/drm/meson/meson_drv.c +++ b/drivers/gpu/drm/meson/meson_drv.c @@ -243,8 +243,8 @@ static int meson_drv_bind_master(struct device *dev, bool has_components) goto free_drm;
drm_mode_config_init(drm);
- drm->mode_config.max_width = 3840;
- drm->mode_config.max_height = 2160;
drm->mode_config.max_width = 16384;
drm->mode_config.max_height = 8192; drm->mode_config.funcs = &meson_mode_config_funcs;
/* Hardware Initialization */
-- 2.7.4
dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel
dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel
On 04/10/2018 20:10, Daniel Vetter wrote:
On Thu, Oct 4, 2018 at 5:05 PM Neil Armstrong narmstrong@baylibre.com wrote:
On 04/10/2018 12:09, Daniel Vetter wrote:
On Thu, Oct 04, 2018 at 10:42:43AM +0200, Neil Armstrong wrote:
The mode_config max_width/max_height determines the maximum framebuffer size the pixel reader can handle. But the values were set thinking they were determining the maximum screen dimensions.
This patch changes the values to the maximum height/width the CANVAS block can handle rounded to some coherent values.
Fixes: a41e82e6c457 ("drm/meson: Add support for components") Signed-off-by: Neil Armstrong narmstrong@baylibre.com
It's both. Grep for all the callers of ->fill_modes and you'll see that this limit is also used to filter max screen sizes.
If you want to change this, then I think we need a new mode_config.fb_max_width/height, which if non-zero, would extend the limit for fbs.
There's also the problem that if you extend this for fbs, then there's no check anymore in the atomic_commit paths (or legacy modeset), so that needs to be addressed somehow too.
What about adding optionals mode_config.fb_max_width/height and update drm_internal_framebuffer_create() to use these if non-0 or fallback to the mode_config max_width/max_height.
That's what I meant. Except you also need to then fix the gap you've opened in atomic_check, and validate the mode size against mode_config.max_width/height.
OK, won't this be enough ? --- a/include/drm/drm_mode_config.h +++ b/include/drm/drm_mode_config.h @@ -333,6 +333,8 @@ struct drm_mode_config_funcs { * @min_height: minimum fb pixel height on this device * @max_width: maximum fb pixel width on this device * @max_height: maximum fb pixel height on this device + * @max_fb_width: maximum fb buffer width if differs from max_width + * @max_fb_height: maximum fb buffer height if differs from max_height * @funcs: core driver provided mode setting functions * @fb_base: base address of the framebuffer * @poll_enabled: track polling support for this device @@ -508,6 +510,7 @@ struct drm_mode_config {
int min_width, min_height; int max_width, max_height; + int max_fb_width, max_fb_height; const struct drm_mode_config_funcs *funcs; resource_size_t fb_base;
--- a/drivers/gpu/drm/drm_framebuffer.c +++ b/drivers/gpu/drm/drm_framebuffer.c @@ -283,14 +283,20 @@ drm_internal_framebuffer_create(struct drm_device *dev, return ERR_PTR(-EINVAL); }
- if ((config->min_width > r->width) || (r->width > config->max_width)) { + if ((config->min_width > r->width) || + (!config->max_fb_width && r->width > config->max_width) || + (config->max_fb_width && r->width > config->max_fb_width)) { DRM_DEBUG_KMS("bad framebuffer width %d, should be >= %d && <= %d\n", - r->width, config->min_width, config->max_width); + r->width, config->min_width, config->max_fb_width ? + config->max_fb_width : config->max_width); return ERR_PTR(-EINVAL); } - if ((config->min_height > r->height) || (r->height > config->max_height)) { + if ((config->min_height > r->height) || + (!config->max_fb_height && r->height > config->max_height) || + (config->max_fb_height && r->height > config->max_fb_height)) { DRM_DEBUG_KMS("bad framebuffer height %d, should be >= %d && <= %d\n", - r->height, config->min_height, config->max_height); + r->height, config->min_height, config->max_fb_height ? + config->max_fb_height : config->max_height); return ERR_PTR(-EINVAL); }
and in the driver :
+ drm->mode_config.max_width = 4096; + drm->mode_config.max_height = 3840; + drm->mode_config.max_fb_width = 16384; + drm->mode_config.max_fb_height = 8192;
With this I leave the mode filtering intact.
Neil
-Daniel
Neil
Bunch of igt to make sure we're not missing anything would be sweet on top, e.g. e.g. trying to set a mode over the limit and making sure it fails.
Cheers, Daniel
drivers/gpu/drm/meson/meson_drv.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/meson/meson_drv.c b/drivers/gpu/drm/meson/meson_drv.c index d344312..2e29968 100644 --- a/drivers/gpu/drm/meson/meson_drv.c +++ b/drivers/gpu/drm/meson/meson_drv.c @@ -243,8 +243,8 @@ static int meson_drv_bind_master(struct device *dev, bool has_components) goto free_drm;
drm_mode_config_init(drm);
- drm->mode_config.max_width = 3840;
- drm->mode_config.max_height = 2160;
drm->mode_config.max_width = 16384;
drm->mode_config.max_height = 8192; drm->mode_config.funcs = &meson_mode_config_funcs;
/* Hardware Initialization */
-- 2.7.4
dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel
dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel
On Fri, Oct 5, 2018 at 9:39 AM Neil Armstrong narmstrong@baylibre.com wrote:
On 04/10/2018 20:10, Daniel Vetter wrote:
On Thu, Oct 4, 2018 at 5:05 PM Neil Armstrong narmstrong@baylibre.com wrote:
On 04/10/2018 12:09, Daniel Vetter wrote:
On Thu, Oct 04, 2018 at 10:42:43AM +0200, Neil Armstrong wrote:
The mode_config max_width/max_height determines the maximum framebuffer size the pixel reader can handle. But the values were set thinking they were determining the maximum screen dimensions.
This patch changes the values to the maximum height/width the CANVAS block can handle rounded to some coherent values.
Fixes: a41e82e6c457 ("drm/meson: Add support for components") Signed-off-by: Neil Armstrong narmstrong@baylibre.com
It's both. Grep for all the callers of ->fill_modes and you'll see that this limit is also used to filter max screen sizes.
If you want to change this, then I think we need a new mode_config.fb_max_width/height, which if non-zero, would extend the limit for fbs.
There's also the problem that if you extend this for fbs, then there's no check anymore in the atomic_commit paths (or legacy modeset), so that needs to be addressed somehow too.
What about adding optionals mode_config.fb_max_width/height and update drm_internal_framebuffer_create() to use these if non-0 or fallback to the mode_config max_width/max_height.
That's what I meant. Except you also need to then fix the gap you've opened in atomic_check, and validate the mode size against mode_config.max_width/height.
OK, won't this be enough ? --- a/include/drm/drm_mode_config.h +++ b/include/drm/drm_mode_config.h @@ -333,6 +333,8 @@ struct drm_mode_config_funcs {
- @min_height: minimum fb pixel height on this device
- @max_width: maximum fb pixel width on this device
- @max_height: maximum fb pixel height on this device
- @max_fb_width: maximum fb buffer width if differs from max_width
- @max_fb_height: maximum fb buffer height if differs from max_height
- @funcs: core driver provided mode setting functions
- @fb_base: base address of the framebuffer
- @poll_enabled: track polling support for this device
@@ -508,6 +510,7 @@ struct drm_mode_config {
int min_width, min_height; int max_width, max_height;
int max_fb_width, max_fb_height; const struct drm_mode_config_funcs *funcs; resource_size_t fb_base;--- a/drivers/gpu/drm/drm_framebuffer.c +++ b/drivers/gpu/drm/drm_framebuffer.c @@ -283,14 +283,20 @@ drm_internal_framebuffer_create(struct drm_device *dev, return ERR_PTR(-EINVAL); }
if ((config->min_width > r->width) || (r->width > config->max_width)) {
if ((config->min_width > r->width) ||(!config->max_fb_width && r->width > config->max_width) ||(config->max_fb_width && r->width > config->max_fb_width)) { DRM_DEBUG_KMS("bad framebuffer width %d, should be >= %d && <= %d\n",
r->width, config->min_width, config->max_width);
r->width, config->min_width, config->max_fb_width ?config->max_fb_width : config->max_width); return ERR_PTR(-EINVAL); }
if ((config->min_height > r->height) || (r->height > config->max_height)) {
if ((config->min_height > r->height) ||(!config->max_fb_height && r->height > config->max_height) ||(config->max_fb_height && r->height > config->max_fb_height)) { DRM_DEBUG_KMS("bad framebuffer height %d, should be >= %d && <= %d\n",
r->height, config->min_height, config->max_height);
r->height, config->min_height, config->max_fb_height ?config->max_fb_height : config->max_height); return ERR_PTR(-EINVAL); }and in the driver :
drm->mode_config.max_width = 4096;drm->mode_config.max_height = 3840;drm->mode_config.max_fb_width = 16384;drm->mode_config.max_fb_height = 8192;With this I leave the mode filtering intact.
Not enough. See https://dri.freedesktop.org/docs/drm/gpu/drm-kms-helpers.html#c.drm_connecto... and scroll down to mode_valid. You need to filter modes both in the detect paths, and the atomic_check paths.
Detect is explicitly filtered out, but atomic_check was only implicitly filtered, through the max fb size checks. Ok, you could light up a mode that's bigger than max fb, but in practice, no userspace ever did that. But with your code we're missing crucial validation now, and userspace could fall over that. What I think we need is to add mode filter against mode_config.max_width/height in drm_atomic_helper_check_modeset(). Probably best to stuff that into the mode_valid() function.
Cheers, Daniel
Neil
-Daniel
Neil
Bunch of igt to make sure we're not missing anything would be sweet on top, e.g. e.g. trying to set a mode over the limit and making sure it fails.
Cheers, Daniel
drivers/gpu/drm/meson/meson_drv.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/meson/meson_drv.c b/drivers/gpu/drm/meson/meson_drv.c index d344312..2e29968 100644 --- a/drivers/gpu/drm/meson/meson_drv.c +++ b/drivers/gpu/drm/meson/meson_drv.c @@ -243,8 +243,8 @@ static int meson_drv_bind_master(struct device *dev, bool has_components) goto free_drm;
drm_mode_config_init(drm);
- drm->mode_config.max_width = 3840;
- drm->mode_config.max_height = 2160;
drm->mode_config.max_width = 16384;
drm->mode_config.max_height = 8192; drm->mode_config.funcs = &meson_mode_config_funcs;
/* Hardware Initialization */
-- 2.7.4
dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel
dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel
On 05/10/2018 09:58, Daniel Vetter wrote:
On Fri, Oct 5, 2018 at 9:39 AM Neil Armstrong narmstrong@baylibre.com wrote:
[...]
OK, won't this be enough ? --- a/include/drm/drm_mode_config.h +++ b/include/drm/drm_mode_config.h @@ -333,6 +333,8 @@ struct drm_mode_config_funcs {
- @min_height: minimum fb pixel height on this device
- @max_width: maximum fb pixel width on this device
- @max_height: maximum fb pixel height on this device
- @max_fb_width: maximum fb buffer width if differs from max_width
- @max_fb_height: maximum fb buffer height if differs from max_height
- @funcs: core driver provided mode setting functions
- @fb_base: base address of the framebuffer
- @poll_enabled: track polling support for this device
@@ -508,6 +510,7 @@ struct drm_mode_config {
int min_width, min_height; int max_width, max_height;
int max_fb_width, max_fb_height; const struct drm_mode_config_funcs *funcs; resource_size_t fb_base;--- a/drivers/gpu/drm/drm_framebuffer.c +++ b/drivers/gpu/drm/drm_framebuffer.c @@ -283,14 +283,20 @@ drm_internal_framebuffer_create(struct drm_device *dev, return ERR_PTR(-EINVAL); }
if ((config->min_width > r->width) || (r->width > config->max_width)) {
if ((config->min_width > r->width) ||(!config->max_fb_width && r->width > config->max_width) ||(config->max_fb_width && r->width > config->max_fb_width)) { DRM_DEBUG_KMS("bad framebuffer width %d, should be >= %d && <= %d\n",
r->width, config->min_width, config->max_width);
r->width, config->min_width, config->max_fb_width ?config->max_fb_width : config->max_width); return ERR_PTR(-EINVAL); }
if ((config->min_height > r->height) || (r->height > config->max_height)) {
if ((config->min_height > r->height) ||(!config->max_fb_height && r->height > config->max_height) ||(config->max_fb_height && r->height > config->max_fb_height)) { DRM_DEBUG_KMS("bad framebuffer height %d, should be >= %d && <= %d\n",
r->height, config->min_height, config->max_height);
r->height, config->min_height, config->max_fb_height ?config->max_fb_height : config->max_height); return ERR_PTR(-EINVAL); }and in the driver :
drm->mode_config.max_width = 4096;drm->mode_config.max_height = 3840;drm->mode_config.max_fb_width = 16384;drm->mode_config.max_fb_height = 8192;With this I leave the mode filtering intact.
Not enough. See https://dri.freedesktop.org/docs/drm/gpu/drm-kms-helpers.html#c.drm_connecto... and scroll down to mode_valid. You need to filter modes both in the detect paths, and the atomic_check paths.
Detect is explicitly filtered out, but atomic_check was only implicitly filtered, through the max fb size checks. Ok, you could light up a mode that's bigger than max fb, but in practice, no userspace ever did that. But with your code we're missing crucial validation now, and userspace could fall over that. What I think we need is to add mode filter against mode_config.max_width/height in drm_atomic_helper_check_modeset(). Probably best to stuff that into the mode_valid() function.
Ok I understood now, thanks for pointer, I'll try to add this.
Neil
Cheers, Daniel
Neil
-Daniel
Neil
Bunch of igt to make sure we're not missing anything would be sweet on top, e.g. e.g. trying to set a mode over the limit and making sure it fails.
Cheers, Daniel
drivers/gpu/drm/meson/meson_drv.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/meson/meson_drv.c b/drivers/gpu/drm/meson/meson_drv.c index d344312..2e29968 100644 --- a/drivers/gpu/drm/meson/meson_drv.c +++ b/drivers/gpu/drm/meson/meson_drv.c @@ -243,8 +243,8 @@ static int meson_drv_bind_master(struct device *dev, bool has_components) goto free_drm;
drm_mode_config_init(drm);
- drm->mode_config.max_width = 3840;
- drm->mode_config.max_height = 2160;
drm->mode_config.max_width = 16384;
drm->mode_config.max_height = 8192; drm->mode_config.funcs = &meson_mode_config_funcs;
/* Hardware Initialization */
-- 2.7.4
dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel
dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel
Reviving this thread from the context of the below conversion:
https://lore.kernel.org/linux-arm-msm/db26145b-3f64-a334-f698-76f972332881@b...
On 2018-10-05 01:19, Neil Armstrong wrote:
On 05/10/2018 09:58, Daniel Vetter wrote:
On Fri, Oct 5, 2018 at 9:39 AM Neil Armstrong narmstrong@baylibre.com wrote:
[...]
OK, won't this be enough ? --- a/include/drm/drm_mode_config.h +++ b/include/drm/drm_mode_config.h @@ -333,6 +333,8 @@ struct drm_mode_config_funcs {
- @min_height: minimum fb pixel height on this device
- @max_width: maximum fb pixel width on this device
- @max_height: maximum fb pixel height on this device
- @max_fb_width: maximum fb buffer width if differs from max_width
- @max_fb_height: maximum fb buffer height if differs from
max_height
- @funcs: core driver provided mode setting functions
- @fb_base: base address of the framebuffer
- @poll_enabled: track polling support for this device
@@ -508,6 +510,7 @@ struct drm_mode_config {
int min_width, min_height; int max_width, max_height;
int max_fb_width, max_fb_height; const struct drm_mode_config_funcs *funcs; resource_size_t fb_base;--- a/drivers/gpu/drm/drm_framebuffer.c +++ b/drivers/gpu/drm/drm_framebuffer.c @@ -283,14 +283,20 @@ drm_internal_framebuffer_create(struct drm_device *dev, return ERR_PTR(-EINVAL); }
if ((config->min_width > r->width) || (r->width >config->max_width)) {
if ((config->min_width > r->width) ||(!config->max_fb_width && r->width > config->max_width)||
(config->max_fb_width && r->width >config->max_fb_width)) { DRM_DEBUG_KMS("bad framebuffer width %d, should be >= %d && <= %d\n",
r->width, config->min_width,config->max_width);
r->width, config->min_width,config->max_fb_width ?
config->max_fb_width : config->max_width); return ERR_PTR(-EINVAL); }
if ((config->min_height > r->height) || (r->height >config->max_height)) {
if ((config->min_height > r->height) ||(!config->max_fb_height && r->height >config->max_height) ||
(config->max_fb_height && r->height >config->max_fb_height)) { DRM_DEBUG_KMS("bad framebuffer height %d, should be
= %d && <= %d\n",
r->height, config->min_height,config->max_height);
r->height, config->min_height,config->max_fb_height ?
config->max_fb_height :config->max_height); return ERR_PTR(-EINVAL); }
and in the driver :
drm->mode_config.max_width = 4096;drm->mode_config.max_height = 3840;drm->mode_config.max_fb_width = 16384;drm->mode_config.max_fb_height = 8192;With this I leave the mode filtering intact.
Not enough. See https://dri.freedesktop.org/docs/drm/gpu/drm-kms-helpers.html#c.drm_connecto... and scroll down to mode_valid. You need to filter modes both in the detect paths, and the atomic_check paths.
Detect is explicitly filtered out, but atomic_check was only implicitly filtered, through the max fb size checks. Ok, you could light up a mode that's bigger than max fb, but in practice, no userspace ever did that.
Daniel, MSM and few other vendor hardware have upscale blocks where the driver can expose fb sizes smaller than the mode resolution and use h/w upscaling to fill the screen. This would optimize the fetch bandwidth.
But with your code we're missing crucial
validation now, and userspace could fall over that. What I think we need is to add mode filter against mode_config.max_width/height in drm_atomic_helper_check_modeset(). Probably best to stuff that into the mode_valid() function.
Agreed! Since the above patch from Niel is taking care of cases where max/min fb values are not set, by checking against the original max/min values, can we separate out this core change from the driver level mode_valid changes? If Niel couldn't find the time, I can repost the above change.
Thanks and Regards, Jeykumar S.
Ok I understood now, thanks for pointer, I'll try to add this.
Neil
Cheers, Daniel
Neil
-Daniel
Neil
Bunch of igt to make sure we're not missing anything would be sweet on top, e.g. e.g. trying to set a mode over the limit and making sure it fails.
Cheers, Daniel
> --- > drivers/gpu/drm/meson/meson_drv.c | 4 ++-- > 1 file changed, 2 insertions(+), 2 deletions(-) > > diff --git a/drivers/gpu/drm/meson/meson_drv.c > b/drivers/gpu/drm/meson/meson_drv.c > index d344312..2e29968 100644 > --- a/drivers/gpu/drm/meson/meson_drv.c > +++ b/drivers/gpu/drm/meson/meson_drv.c > @@ -243,8 +243,8 @@ static int meson_drv_bind_master(struct > device *dev, bool has_components) > goto free_drm; > > drm_mode_config_init(drm); > - drm->mode_config.max_width = 3840; > - drm->mode_config.max_height = 2160; > + drm->mode_config.max_width = 16384; > + drm->mode_config.max_height = 8192; > drm->mode_config.funcs = &meson_mode_config_funcs; > > /* Hardware Initialization */ > -- > 2.7.4 > > _______________________________________________ > dri-devel mailing list > dri-devel@lists.freedesktop.org > https://lists.freedesktop.org/mailman/listinfo/dri-devel
dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel
dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel
On Tue, Sep 24, 2019 at 10:28:48AM -0700, Jeykumar Sankaran wrote:
Reviving this thread from the context of the below conversion:
https://lore.kernel.org/linux-arm-msm/db26145b-3f64-a334-f698-76f972332881@b...
On 2018-10-05 01:19, Neil Armstrong wrote:
On 05/10/2018 09:58, Daniel Vetter wrote:
On Fri, Oct 5, 2018 at 9:39 AM Neil Armstrong narmstrong@baylibre.com wrote:
[...]
OK, won't this be enough ? --- a/include/drm/drm_mode_config.h +++ b/include/drm/drm_mode_config.h @@ -333,6 +333,8 @@ struct drm_mode_config_funcs {
- @min_height: minimum fb pixel height on this device
- @max_width: maximum fb pixel width on this device
- @max_height: maximum fb pixel height on this device
- @max_fb_width: maximum fb buffer width if differs from max_width
- @max_fb_height: maximum fb buffer height if differs from
max_height
- @funcs: core driver provided mode setting functions
- @fb_base: base address of the framebuffer
- @poll_enabled: track polling support for this device
@@ -508,6 +510,7 @@ struct drm_mode_config {
int min_width, min_height; int max_width, max_height;
int max_fb_width, max_fb_height; const struct drm_mode_config_funcs *funcs; resource_size_t fb_base;--- a/drivers/gpu/drm/drm_framebuffer.c +++ b/drivers/gpu/drm/drm_framebuffer.c @@ -283,14 +283,20 @@ drm_internal_framebuffer_create(struct drm_device *dev, return ERR_PTR(-EINVAL); }
if ((config->min_width > r->width) || (r->width >config->max_width)) {
if ((config->min_width > r->width) ||(!config->max_fb_width && r->width >config->max_width) ||
(config->max_fb_width && r->width >config->max_fb_width)) { DRM_DEBUG_KMS("bad framebuffer width %d, should be >= %d && <= %d\n",
r->width, config->min_width,config->max_width);
r->width, config->min_width,config->max_fb_width ?
config->max_fb_width : config->max_width); return ERR_PTR(-EINVAL); }
if ((config->min_height > r->height) || (r->height >config->max_height)) {
if ((config->min_height > r->height) ||(!config->max_fb_height && r->height >config->max_height) ||
(config->max_fb_height && r->height >config->max_fb_height)) { DRM_DEBUG_KMS("bad framebuffer height %d, should be >= %d && <= %d\n",
r->height, config->min_height,config->max_height);
r->height, config->min_height,config->max_fb_height ?
config->max_fb_height :config->max_height); return ERR_PTR(-EINVAL); }
and in the driver :
drm->mode_config.max_width = 4096;drm->mode_config.max_height = 3840;drm->mode_config.max_fb_width = 16384;drm->mode_config.max_fb_height = 8192;With this I leave the mode filtering intact.
Not enough. See https://dri.freedesktop.org/docs/drm/gpu/drm-kms-helpers.html#c.drm_connecto... and scroll down to mode_valid. You need to filter modes both in the detect paths, and the atomic_check paths.
Detect is explicitly filtered out, but atomic_check was only implicitly filtered, through the max fb size checks. Ok, you could light up a mode that's bigger than max fb, but in practice, no userspace ever did that.
Daniel, MSM and few other vendor hardware have upscale blocks where the driver can expose fb sizes smaller than the mode resolution and use h/w upscaling to fill the screen. This would optimize the fetch bandwidth.
But with your code we're missing crucial
validation now, and userspace could fall over that. What I think we need is to add mode filter against mode_config.max_width/height in drm_atomic_helper_check_modeset(). Probably best to stuff that into the mode_valid() function.
Agreed! Since the above patch from Niel is taking care of cases where max/min fb values are not set, by checking against the original max/min values, can we separate out this core change from the driver level mode_valid changes? If Niel couldn't find the time, I can repost the above change.
Sure, I think Neil wouldn't mind if you take this over and get it ready for merging. Just need to make sure we're not leaving any validation gaps in core/helper code. -Daniel
Thanks and Regards, Jeykumar S.
Ok I understood now, thanks for pointer, I'll try to add this.
Neil
Cheers, Daniel
Neil
-Daniel
Neil
> > Bunch of igt to make sure we're not missing anything > would be sweet on > top, e.g. e.g. trying to set a mode over the limit > and making sure it > fails. > > Cheers, Daniel > > > --- > > drivers/gpu/drm/meson/meson_drv.c | 4 ++-- > > 1 file changed, 2 insertions(+), 2 deletions(-) > > > > diff --git a/drivers/gpu/drm/meson/meson_drv.c > > b/drivers/gpu/drm/meson/meson_drv.c > > index d344312..2e29968 100644 > > --- a/drivers/gpu/drm/meson/meson_drv.c > > +++ b/drivers/gpu/drm/meson/meson_drv.c > > @@ -243,8 +243,8 @@ static int > > meson_drv_bind_master(struct device *dev, bool > > has_components) > > goto free_drm; > > > > drm_mode_config_init(drm); > > - drm->mode_config.max_width = 3840; > > - drm->mode_config.max_height = 2160; > > + drm->mode_config.max_width = 16384; > > + drm->mode_config.max_height = 8192; > > drm->mode_config.funcs = &meson_mode_config_funcs; > > > > /* Hardware Initialization */ > > -- > > 2.7.4 > > > > _______________________________________________ > > dri-devel mailing list > > dri-devel@lists.freedesktop.org > > https://lists.freedesktop.org/mailman/listinfo/dri-devel >
dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel
dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel
-- Jeykumar S
On 2019-10-09 03:47, Daniel Vetter wrote:
On Tue, Sep 24, 2019 at 10:28:48AM -0700, Jeykumar Sankaran wrote:
Reviving this thread from the context of the below conversion:
https://lore.kernel.org/linux-arm-msm/db26145b-3f64-a334-f698-76f972332881 @baylibre.com/T/#u
On 2018-10-05 01:19, Neil Armstrong wrote:
On 05/10/2018 09:58, Daniel Vetter wrote:
On Fri, Oct 5, 2018 at 9:39 AM Neil Armstrong narmstrong@baylibre.com wrote:
[...]
OK, won't this be enough ? --- a/include/drm/drm_mode_config.h +++ b/include/drm/drm_mode_config.h @@ -333,6 +333,8 @@ struct drm_mode_config_funcs {
- @min_height: minimum fb pixel height on this device
- @max_width: maximum fb pixel width on this device
- @max_height: maximum fb pixel height on this device
- @max_fb_width: maximum fb buffer width if differs from
max_width
- @max_fb_height: maximum fb buffer height if differs from
max_height
- @funcs: core driver provided mode setting functions
- @fb_base: base address of the framebuffer
- @poll_enabled: track polling support for this device
@@ -508,6 +510,7 @@ struct drm_mode_config {
int min_width, min_height; int max_width, max_height;
int max_fb_width, max_fb_height; const struct drm_mode_config_funcs *funcs; resource_size_t fb_base;--- a/drivers/gpu/drm/drm_framebuffer.c +++ b/drivers/gpu/drm/drm_framebuffer.c @@ -283,14 +283,20 @@ drm_internal_framebuffer_create(struct drm_device *dev, return ERR_PTR(-EINVAL); }
if ((config->min_width > r->width) || (r->width >config->max_width)) {
if ((config->min_width > r->width) ||(!config->max_fb_width && r->width >config->max_width) ||
(config->max_fb_width && r->width >config->max_fb_width)) { DRM_DEBUG_KMS("bad framebuffer width %d, should be >= %d && <= %d\n",
r->width, config->min_width,config->max_width);
r->width, config->min_width,config->max_fb_width ?
config->max_fb_width :config->max_width);
return ERR_PTR(-EINVAL); }
if ((config->min_height > r->height) || (r->height >config->max_height)) {
if ((config->min_height > r->height) ||(!config->max_fb_height && r->height >config->max_height) ||
(config->max_fb_height && r->height >config->max_fb_height)) { DRM_DEBUG_KMS("bad framebuffer height %d, should be >= %d && <= %d\n",
r->height, config->min_height,config->max_height);
r->height, config->min_height,config->max_fb_height ?
config->max_fb_height :config->max_height); return ERR_PTR(-EINVAL); }
and in the driver :
drm->mode_config.max_width = 4096;drm->mode_config.max_height = 3840;drm->mode_config.max_fb_width = 16384;drm->mode_config.max_fb_height = 8192;With this I leave the mode filtering intact.
Not enough. See
https://dri.freedesktop.org/docs/drm/gpu/drm-kms-helpers.html#c.drm_connec tor_helper_funcs
and scroll down to mode_valid. You need to filter modes both in the detect paths, and the atomic_check paths.
Detect is explicitly filtered out, but atomic_check was only implicitly filtered, through the max fb size checks. Ok, you could light up a mode that's bigger than max fb, but in practice, no userspace ever did that.
Daniel, MSM and few other vendor hardware have upscale blocks where the driver can expose fb sizes smaller than the mode resolution and use h/w upscaling to fill the screen. This would optimize the fetch bandwidth.
But with your code we're missing crucial
validation now, and userspace could fall over that. What I think we need is to add mode filter against mode_config.max_width/height in drm_atomic_helper_check_modeset(). Probably best to stuff that into the mode_valid() function.
Agreed! Since the above patch from Niel is taking care of cases where max/min fb values are not set, by checking against the original max/min values, can we separate out this core change from the driver level mode_valid changes? If Niel couldn't
find
the time, I can repost the above change.
Sure, I think Neil wouldn't mind if you take this over and get it ready for merging. Just need to make sure we're not leaving any validation gaps in core/helper code. -Daniel
I guess you are a bit late for the party!
I did post the patch on the forum. The latest on the thread can be found here: https://lkml.org/lkml/2019/10/2/369
The basic concern is if FB limits are different (especially smaller) than the display (mode) limits, it will break the existing user space, who are creating unscaled FB's out of exposed mode limits.
Thanks and Regards, Jeykumar S.
Thanks and Regards, Jeykumar S.
Ok I understood now, thanks for pointer, I'll try to add this.
Neil
Cheers, Daniel
Neil
-Daniel
> > Neil > > > > > Bunch of igt to make sure we're not missing anything > > would be sweet on > > top, e.g. e.g. trying to set a mode over the limit > > and making sure it > > fails. > > > > Cheers, Daniel > > > > > --- > > > drivers/gpu/drm/meson/meson_drv.c | 4 ++-- > > > 1 file changed, 2 insertions(+), 2 deletions(-) > > > > > > diff --git a/drivers/gpu/drm/meson/meson_drv.c > > > b/drivers/gpu/drm/meson/meson_drv.c > > > index d344312..2e29968 100644 > > > --- a/drivers/gpu/drm/meson/meson_drv.c > > > +++ b/drivers/gpu/drm/meson/meson_drv.c > > > @@ -243,8 +243,8 @@ static int > > > meson_drv_bind_master(struct device *dev, bool > > > has_components) > > > goto free_drm; > > > > > > drm_mode_config_init(drm); > > > - drm->mode_config.max_width = 3840; > > > - drm->mode_config.max_height = 2160; > > > + drm->mode_config.max_width = 16384; > > > + drm->mode_config.max_height = 8192; > > > drm->mode_config.funcs = &meson_mode_config_funcs; > > > > > > /* Hardware Initialization */ > > > -- > > > 2.7.4 > > > > > > _______________________________________________ > > > dri-devel mailing list > > > dri-devel@lists.freedesktop.org > > > https://lists.freedesktop.org/mailman/listinfo/dri-devel > > > > _______________________________________________ > dri-devel mailing list > dri-devel@lists.freedesktop.org > https://lists.freedesktop.org/mailman/listinfo/dri-devel
dri-devel mailing list dri-devel@lists.freedesktop.org https://lists.freedesktop.org/mailman/listinfo/dri-devel
-- Jeykumar S
dri-devel@lists.freedesktop.org
-
Daniel Vetter -
Jeykumar Sankaran -
Neil Armstrong