MSM Mobile Display Subsystem (MDSS) encapsulates sub-blocks like DPU display controller, DSI etc. Add YAML schema for DPU device tree bindings.
Signed-off-by: Krishna Manikandan mkrishn@codeaurora.org Reviewed-by: Rob Herring robh@kernel.org Reviewed-by: Bjorn Andersson bjorn.andersson@linaro.org Reviewed-by: Stephen Boyd swboyd@chromium.org --- Changes in v2: - Changed dpu to DPU (Sam Ravnborg) - Fixed indentation issues (Sam Ravnborg) - Added empty line between different properties (Sam Ravnborg) - Replaced reference txt files with their corresponding yaml files (Sam Ravnborg) - Modified the file to use "|" only when it is necessary (Sam Ravnborg)
Changes in v3: - Corrected the license used (Rob Herring) - Added maxItems for properties (Rob Herring) - Dropped generic descriptions (Rob Herring) - Added ranges property (Rob Herring) - Corrected the indendation (Rob Herring) - Added additionalProperties (Rob Herring) - Split dsi file into two, one for dsi controller and another one for dsi phy per target (Rob Herring) - Corrected description for pinctrl-names (Rob Herring) - Corrected the examples used in yaml file (Rob Herring) - Delete dsi.txt and dpu.txt (Rob Herring)
Changes in v4: - Move schema up by one level (Rob Herring) - Add patternProperties for mdp node (Rob Herring) - Corrected description of some properties (Rob Herring)
Changes in v5: - Correct the indentation (Rob Herring) - Remove unnecessary description from properties (Rob Herring) - Correct the number of interconnect entries (Rob Herring) - Add interconnect names for sc7180 (Rob Herring) - Add description for ports (Rob Herring) - Remove common properties (Rob Herring) - Add unevalutatedProperties (Rob Herring) - Reference existing dsi controller yaml in the common dsi controller file (Rob Herring) - Correct the description of clock names to include only the clocks that are required (Rob Herring) - Remove properties which are already covered under the common binding (Rob Herring) - Add dsi phy supply nodes which are required for sc7180 and sdm845 targets (Rob Herring) - Add type ref for syscon-sfpb (Rob Herring)
Changes in v6: - Fixed errors during dt_binding_check (Rob Herring) - Add maxItems for phys and phys-names (Rob Herring) - Use unevaluatedProperties wherever required (Rob Herring) - Removed interrupt controller from required properties for dsi controller (Rob Herring) - Add constraints for dsi-phy reg-names based on the compatible phy version (Rob Herring) - Add constraints for dsi-phy supply nodes based on the compatible phy version (Rob Herring)
Changes in v7: - Add default value for qcom,mdss-mdp-transfer-time-us (Rob Herring) - Modify the schema for data-lanes (Rob Herring) - Split the phy schema into separate schemas based on the phy version (Rob Herring)
Changes in v8: - Resolve merge conflicts with latest dsi.txt file - Include dp yaml change also in the same series
Changes in v9: - Combine target specific dsi controller yaml files to a single yaml file (Rob Herring) - Combine target specific dsi phy yaml files into a single yaml file (Rob Herring) - Use unevaluatedProperties and additionalProperties wherever required - Remove duplicate properties from common yaml files
Changes in v10: - Split the patch into separate patches for DPU, DSI and PHY (Stephen Boyd) - Drop unnecessary fullstop (Stephen Boyd) - Add newline whereever required (Stephen Boyd) - Add description for clock used (Stephen Boyd) - Modify the description for interconnect entries (Stephen Boyd) - Drop assigned clock entries as it a generic property (Stephen Boyd) - Correct the definition for interrupts (Stephen Boyd) - Drop clock names from required properties (Stephen Boyd) - Drop labels for display nodes from example (Stephen Boyd) - Drop flags from interrupts entries (Stephen Boyd)
Changes in v11: - Drop maxItems for clocks (Stephen Boyd)
Changes in v12: - Add description for register property (Stephen Boyd) - Add maxItems for interrupts (Stephen Boyd) - Add description for iommus property (Stephen Boyd) - Add description for interconnects (Stephen Boyd) - Change display node name to display_controller (Stephen Boyd)
Changes in v13: - Add maxItems for reg property (Stephen Boyd) - Add ranges property in example (Stephen Boyd) - Modify description for iommus property (Stephen Boyd) - Add Dp bindings for ports in the same patch (Stephen Boyd) - Remove soc from examples and change address and size cells accordingly (Stephen Boyd) - Add reference for ports
Changes in v14: - Modify title for SC7180 and SDM845 yaml files (Stephen Boyd) - Add required list for display-controller node (Stephen Boyd)
Changes in v16: - Add reference for port (Rob Herring) - Make additionalProperties as false (Rob Herring) .../bindings/display/msm/dpu-sc7180.yaml | 228 +++++++++++++++++++++ .../bindings/display/msm/dpu-sdm845.yaml | 212 +++++++++++++++++++ .../devicetree/bindings/display/msm/dpu.txt | 141 ------------- 3 files changed, 440 insertions(+), 141 deletions(-) create mode 100644 Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml create mode 100644 Documentation/devicetree/bindings/display/msm/dpu-sdm845.yaml delete mode 100644 Documentation/devicetree/bindings/display/msm/dpu.txt
diff --git a/Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml b/Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml new file mode 100644 index 0000000..12a86b1 --- /dev/null +++ b/Documentation/devicetree/bindings/display/msm/dpu-sc7180.yaml @@ -0,0 +1,228 @@ +# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/msm/dpu-sc7180.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Display DPU dt properties for SC7180 target + +maintainers: + - Krishna Manikandan mkrishn@codeaurora.org + +description: | + Device tree bindings for MSM Mobile Display Subsystem(MDSS) that encapsulates + sub-blocks like DPU display controller, DSI and DP interfaces etc. Device tree + bindings of MDSS and DPU are mentioned for SC7180 target. + +properties: + compatible: + items: + - const: qcom,sc7180-mdss + + reg: + maxItems: 1 + + reg-names: + const: mdss + + power-domains: + maxItems: 1 + + clocks: + items: + - description: Display AHB clock from gcc + - description: Display AHB clock from dispcc + - description: Display core clock + + clock-names: + items: + - const: iface + - const: ahb + - const: core + + interrupts: + maxItems: 1 + + interrupt-controller: true + + "#address-cells": true + + "#size-cells": true + + "#interrupt-cells": + const: 1 + + iommus: + items: + - description: Phandle to apps_smmu node with SID mask for Hard-Fail port0 + + ranges: true + + interconnects: + items: + - description: Interconnect path specifying the port ids for data bus + + interconnect-names: + const: mdp0-mem + +patternProperties: + "^display-controller@[0-9a-f]+$": + type: object + description: Node containing the properties of DPU. + + properties: + compatible: + items: + - const: qcom,sc7180-dpu + + reg: + items: + - description: Address offset and size for mdp register set + - description: Address offset and size for vbif register set + + reg-names: + items: + - const: mdp + - const: vbif + + clocks: + items: + - description: Display hf axi clock + - description: Display ahb clock + - description: Display rotator clock + - description: Display lut clock + - description: Display core clock + - description: Display vsync clock + + clock-names: + items: + - const: bus + - const: iface + - const: rot + - const: lut + - const: core + - const: vsync + + interrupts: + maxItems: 1 + + power-domains: + maxItems: 1 + + operating-points-v2: true + + ports: + $ref: /schemas/graph.yaml#/properties/ports + description: | + Contains the list of output ports from DPU device. These ports + connect to interfaces that are external to the DPU hardware, + such as DSI, DP etc. Each output port contains an endpoint that + describes how it is connected to an external interface. + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: DPU_INTF1 (DSI1) + + port@2: + $ref: /schemas/graph.yaml#/properties/port + description: DPU_INTF0 (DP) + + required: + - port@0 + + required: + - compatible + - reg + - reg-names + - clocks + - interrupts + - power-domains + - operating-points-v2 + - ports + +required: + - compatible + - reg + - reg-names + - power-domains + - clocks + - interrupts + - interrupt-controller + - iommus + - ranges + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,dispcc-sc7180.h> + #include <dt-bindings/clock/qcom,gcc-sc7180.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interconnect/qcom,sdm845.h> + #include <dt-bindings/power/qcom-rpmpd.h> + + display-subsystem@ae00000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "qcom,sc7180-mdss"; + reg = <0xae00000 0x1000>; + reg-names = "mdss"; + power-domains = <&dispcc MDSS_GDSC>; + clocks = <&gcc GCC_DISP_AHB_CLK>, + <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&dispcc DISP_CC_MDSS_MDP_CLK>; + clock-names = "iface", "ahb", "core"; + + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <1>; + + interconnects = <&mmss_noc MASTER_MDP0 &mc_virt SLAVE_EBI1>; + interconnect-names = "mdp0-mem"; + + iommus = <&apps_smmu 0x800 0x2>; + ranges; + + display-controller@ae01000 { + compatible = "qcom,sc7180-dpu"; + reg = <0x0ae01000 0x8f000>, + <0x0aeb0000 0x2008>; + + reg-names = "mdp", "vbif"; + + clocks = <&gcc GCC_DISP_HF_AXI_CLK>, + <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&dispcc DISP_CC_MDSS_ROT_CLK>, + <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>, + <&dispcc DISP_CC_MDSS_MDP_CLK>, + <&dispcc DISP_CC_MDSS_VSYNC_CLK>; + clock-names = "bus", "iface", "rot", "lut", "core", + "vsync"; + + interrupt-parent = <&mdss>; + interrupts = <0>; + power-domains = <&rpmhpd SC7180_CX>; + operating-points-v2 = <&mdp_opp_table>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + dpu_intf1_out: endpoint { + remote-endpoint = <&dsi0_in>; + }; + }; + + port@2 { + reg = <2>; + dpu_intf0_out: endpoint { + remote-endpoint = <&dp_in>; + }; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/display/msm/dpu-sdm845.yaml b/Documentation/devicetree/bindings/display/msm/dpu-sdm845.yaml new file mode 100644 index 0000000..b4ea7c9 --- /dev/null +++ b/Documentation/devicetree/bindings/display/msm/dpu-sdm845.yaml @@ -0,0 +1,212 @@ +# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/msm/dpu-sdm845.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Display DPU dt properties for SDM845 target + +maintainers: + - Krishna Manikandan mkrishn@codeaurora.org + +description: | + Device tree bindings for MSM Mobile Display Subsystem(MDSS) that encapsulates + sub-blocks like DPU display controller, DSI and DP interfaces etc. Device tree + bindings of MDSS and DPU are mentioned for SDM845 target. + +properties: + compatible: + items: + - const: qcom,sdm845-mdss + + reg: + maxItems: 1 + + reg-names: + const: mdss + + power-domains: + maxItems: 1 + + clocks: + items: + - description: Display AHB clock from gcc + - description: Display AXI clock + - description: Display core clock + + clock-names: + items: + - const: iface + - const: bus + - const: core + + interrupts: + maxItems: 1 + + interrupt-controller: true + + "#address-cells": true + + "#size-cells": true + + "#interrupt-cells": + const: 1 + + iommus: + items: + - description: Phandle to apps_smmu node with SID mask for Hard-Fail port0 + - description: Phandle to apps_smmu node with SID mask for Hard-Fail port1 + + ranges: true + +patternProperties: + "^display-controller@[0-9a-f]+$": + type: object + description: Node containing the properties of DPU. + + properties: + compatible: + items: + - const: qcom,sdm845-dpu + + reg: + items: + - description: Address offset and size for mdp register set + - description: Address offset and size for vbif register set + + reg-names: + items: + - const: mdp + - const: vbif + + clocks: + items: + - description: Display ahb clock + - description: Display axi clock + - description: Display core clock + - description: Display vsync clock + + clock-names: + items: + - const: iface + - const: bus + - const: core + - const: vsync + + interrupts: + maxItems: 1 + + power-domains: + maxItems: 1 + + operating-points-v2: true + ports: + $ref: /schemas/graph.yaml#/properties/ports + description: | + Contains the list of output ports from DPU device. These ports + connect to interfaces that are external to the DPU hardware, + such as DSI, DP etc. Each output port contains an endpoint that + describes how it is connected to an external interface. + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: DPU_INTF1 (DSI1) + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: DPU_INTF2 (DSI2) + + required: + - port@0 + - port@1 + + required: + - compatible + - reg + - reg-names + - clocks + - interrupts + - power-domains + - operating-points-v2 + - ports + +required: + - compatible + - reg + - reg-names + - power-domains + - clocks + - interrupts + - interrupt-controller + - iommus + - ranges + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,dispcc-sdm845.h> + #include <dt-bindings/clock/qcom,gcc-sdm845.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/qcom-rpmpd.h> + + display-subsystem@ae00000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "qcom,sdm845-mdss"; + reg = <0x0ae00000 0x1000>; + reg-names = "mdss"; + power-domains = <&dispcc MDSS_GDSC>; + + clocks = <&gcc GCC_DISP_AHB_CLK>, + <&gcc GCC_DISP_AXI_CLK>, + <&dispcc DISP_CC_MDSS_MDP_CLK>; + clock-names = "iface", "bus", "core"; + + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <1>; + + iommus = <&apps_smmu 0x880 0x8>, + <&apps_smmu 0xc80 0x8>; + ranges; + + display-controller@ae01000 { + compatible = "qcom,sdm845-dpu"; + reg = <0x0ae01000 0x8f000>, + <0x0aeb0000 0x2008>; + reg-names = "mdp", "vbif"; + + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&dispcc DISP_CC_MDSS_AXI_CLK>, + <&dispcc DISP_CC_MDSS_MDP_CLK>, + <&dispcc DISP_CC_MDSS_VSYNC_CLK>; + clock-names = "iface", "bus", "core", "vsync"; + + interrupt-parent = <&mdss>; + interrupts = <0>; + power-domains = <&rpmhpd SDM845_CX>; + operating-points-v2 = <&mdp_opp_table>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + dpu_intf1_out: endpoint { + remote-endpoint = <&dsi0_in>; + }; + }; + + port@1 { + reg = <1>; + dpu_intf2_out: endpoint { + remote-endpoint = <&dsi1_in>; + }; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/display/msm/dpu.txt b/Documentation/devicetree/bindings/display/msm/dpu.txt deleted file mode 100644 index 586e6ea..0000000 --- a/Documentation/devicetree/bindings/display/msm/dpu.txt +++ /dev/null @@ -1,141 +0,0 @@ -Qualcomm Technologies, Inc. DPU KMS - -Description: - -Device tree bindings for MSM Mobile Display Subsystem(MDSS) that encapsulates -sub-blocks like DPU display controller, DSI and DP interfaces etc. -The DPU display controller is found in SDM845 SoC. - -MDSS: -Required properties: -- compatible: "qcom,sdm845-mdss", "qcom,sc7180-mdss" -- reg: physical base address and length of controller's registers. -- reg-names: register region names. The following region is required: - * "mdss" -- power-domains: a power domain consumer specifier according to - Documentation/devicetree/bindings/power/power_domain.txt -- clocks: list of clock specifiers for clocks needed by the device. -- clock-names: device clock names, must be in same order as clocks property. - The following clocks are required: - * "iface" - * "bus" - * "core" -- interrupts: interrupt signal from MDSS. -- interrupt-controller: identifies the node as an interrupt controller. -- #interrupt-cells: specifies the number of cells needed to encode an interrupt - source, should be 1. -- iommus: phandle of iommu device node. -- #address-cells: number of address cells for the MDSS children. Should be 1. -- #size-cells: Should be 1. -- ranges: parent bus address space is the same as the child bus address space. -- interconnects : interconnect path specifier for MDSS according to - Documentation/devicetree/bindings/interconnect/interconnect.txt. Should be - 2 paths corresponding to 2 AXI ports. -- interconnect-names : MDSS will have 2 port names to differentiate between the - 2 interconnect paths defined with interconnect specifier. - -Optional properties: -- assigned-clocks: list of clock specifiers for clocks needing rate assignment -- assigned-clock-rates: list of clock frequencies sorted in the same order as - the assigned-clocks property. - -MDP: -Required properties: -- compatible: "qcom,sdm845-dpu", "qcom,sc7180-dpu" -- reg: physical base address and length of controller's registers. -- reg-names : register region names. The following region is required: - * "mdp" - * "vbif" -- clocks: list of clock specifiers for clocks needed by the device. -- clock-names: device clock names, must be in same order as clocks property. - The following clocks are required. - * "bus" - * "iface" - * "core" - * "vsync" -- interrupts: interrupt line from DPU to MDSS. -- ports: contains the list of output ports from DPU device. These ports connect - to interfaces that are external to the DPU hardware, such as DSI, DP etc. - - Each output port contains an endpoint that describes how it is connected to an - external interface. These are described by the standard properties documented - here: - Documentation/devicetree/bindings/graph.txt - Documentation/devicetree/bindings/media/video-interfaces.txt - - Port 0 -> DPU_INTF1 (DSI1) - Port 1 -> DPU_INTF2 (DSI2) - -Optional properties: -- assigned-clocks: list of clock specifiers for clocks needing rate assignment -- assigned-clock-rates: list of clock frequencies sorted in the same order as - the assigned-clocks property. - -Example: - - mdss: mdss@ae00000 { - compatible = "qcom,sdm845-mdss"; - reg = <0xae00000 0x1000>; - reg-names = "mdss"; - - power-domains = <&clock_dispcc 0>; - - clocks = <&gcc GCC_DISP_AHB_CLK>, <&gcc GCC_DISP_AXI_CLK>, - <&clock_dispcc DISP_CC_MDSS_MDP_CLK>; - clock-names = "iface", "bus", "core"; - - assigned-clocks = <&clock_dispcc DISP_CC_MDSS_MDP_CLK>; - assigned-clock-rates = <300000000>; - - interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; - interrupt-controller; - #interrupt-cells = <1>; - - interconnects = <&rsc_hlos MASTER_MDP0 &rsc_hlos SLAVE_EBI1>, - <&rsc_hlos MASTER_MDP1 &rsc_hlos SLAVE_EBI1>; - - interconnect-names = "mdp0-mem", "mdp1-mem"; - - iommus = <&apps_iommu 0>; - - #address-cells = <2>; - #size-cells = <1>; - ranges = <0 0 0xae00000 0xb2008>; - - mdss_mdp: mdp@ae01000 { - compatible = "qcom,sdm845-dpu"; - reg = <0 0x1000 0x8f000>, <0 0xb0000 0x2008>; - reg-names = "mdp", "vbif"; - - clocks = <&clock_dispcc DISP_CC_MDSS_AHB_CLK>, - <&clock_dispcc DISP_CC_MDSS_AXI_CLK>, - <&clock_dispcc DISP_CC_MDSS_MDP_CLK>, - <&clock_dispcc DISP_CC_MDSS_VSYNC_CLK>; - clock-names = "iface", "bus", "core", "vsync"; - - assigned-clocks = <&clock_dispcc DISP_CC_MDSS_MDP_CLK>, - <&clock_dispcc DISP_CC_MDSS_VSYNC_CLK>; - assigned-clock-rates = <0 0 300000000 19200000>; - - interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - dpu_intf1_out: endpoint { - remote-endpoint = <&dsi0_in>; - }; - }; - - port@1 { - reg = <1>; - dpu_intf2_out: endpoint { - remote-endpoint = <&dsi1_in>; - }; - }; - }; - }; - };
Add YAML schema for the device tree bindings for DSI
Signed-off-by: Krishna Manikandan mkrishn@codeaurora.org Reviewed-by: Bjorn Andersson bjorn.andersson@linaro.org Reviewed-by: Stephen Boyd swboyd@chromium.org --- Changes in v1: - Separate dsi controller bindings to a separate patch (Stephen Boyd) - Merge dsi-common-controller.yaml and dsi-controller-main.yaml to a single file (Stephen Boyd) - Drop supply entries and definitions from properties (Stephen Boyd) - Modify phy-names property for dsi controller (Stephen Boyd) - Remove boolean from description (Stephen Boyd) - Drop pinctrl properties as they are standard entries (Stephen Boyd) - Modify the description for ports property and keep the reference to the generic binding where this is defined (Stephen Boyd) - Add description to clock names (Stephen Boyd) - Correct the indendation (Stephen Boyd) - Drop the label for display dt nodes and correct the node name (Stephen Boyd)
Changes in v2: - Drop maxItems for clock (Stephen Boyd) - Drop qcom,mdss-mdp-transfer-time-us as it is not used in upstream dt file (Stephen Boyd) - Keep child node directly under soc node (Stephen Boyd) - Drop qcom,sync-dual-dsi as it is not used in upstream dt
Changes in v3: - Add description for register property (Stephen Boyd)
Changes in v4: - Add maxItems for phys property (Stephen Boyd) - Add maxItems for reg property (Stephen Boyd) - Add reference for data-lanes property (Stephen Boyd) - Remove soc from example (Stephen Boyd)
Changes in v5: - Modify title and description (Stephen Boyd) - Add required properties for ports node (Stephen Boyd) - Add data-lanes in the example (Stephen Boyd) - Drop qcom,master-dsi property (Stephen Boyd)
Changes in v6: - Add required properties for port@0, port@1 and corresponding endpoints (Stephen Boyd) - Add address-cells and size-cells for ports (Stephen Boyd) - Use additionalProperties instead of unevaluatedProperties (Stephen Boyd)
Changes in v7: - Add reference for ports and data-lanes (Rob Herring) - Add maxItems and minItems for data-lanes (Rob Herring)
Changes in v8: - Drop common properties and description from ports (Rob Herring) - Add reference for endpoint (Rob Herring) - Add correct reference for data-lanes (Rob Herring) - Drop common properties from required list for ports (Rob Herring)
Changes in v9: - Drop reference for data-lanes (Rob Herring) - Add unevaluatedProperties for endpoint (Rob Herring)
.../bindings/display/msm/dsi-controller-main.yaml | 185 +++++++++++++++ .../devicetree/bindings/display/msm/dsi.txt | 249 --------------------- 2 files changed, 185 insertions(+), 249 deletions(-) create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml delete mode 100644 Documentation/devicetree/bindings/display/msm/dsi.txt
diff --git a/Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml b/Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml new file mode 100644 index 0000000..76348b7 --- /dev/null +++ b/Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml @@ -0,0 +1,185 @@ +# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/msm/dsi-controller-main.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Display DSI controller + +maintainers: + - Krishna Manikandan mkrishn@codeaurora.org + +allOf: + - $ref: "../dsi-controller.yaml#" + +properties: + compatible: + items: + - const: qcom,mdss-dsi-ctrl + + reg: + maxItems: 1 + + reg-names: + const: dsi_ctrl + + interrupts: + maxItems: 1 + + clocks: + items: + - description: Display byte clock + - description: Display byte interface clock + - description: Display pixel clock + - description: Display escape clock + - description: Display AHB clock + - description: Display AXI clock + + clock-names: + items: + - const: byte + - const: byte_intf + - const: pixel + - const: core + - const: iface + - const: bus + + phys: + maxItems: 1 + + phy-names: + const: dsi + + "#address-cells": true + + "#size-cells": true + + syscon-sfpb: + description: A phandle to mmss_sfpb syscon node (only for DSIv2). + $ref: "/schemas/types.yaml#/definitions/phandle" + + qcom,dual-dsi-mode: + type: boolean + description: | + Indicates if the DSI controller is driving a panel which needs + 2 DSI links. + + power-domains: + maxItems: 1 + + operating-points-v2: true + + ports: + $ref: "/schemas/graph.yaml#/properties/ports" + description: | + Contains DSI controller input and output ports as children, each + containing one endpoint subnode. + + properties: + port@0: + $ref: "/schemas/graph.yaml#/properties/port" + description: | + Input endpoints of the controller. + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + properties: + data-lanes: + maxItems: 4 + minItems: 4 + items: + enum: [ 0, 1, 2, 3 ] + + port@1: + $ref: "/schemas/graph.yaml#/properties/port" + description: | + Output endpoints of the controller. + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + properties: + data-lanes: + maxItems: 4 + minItems: 4 + items: + enum: [ 0, 1, 2, 3 ] + + required: + - port@0 + - port@1 + +required: + - compatible + - reg + - reg-names + - interrupts + - clocks + - clock-names + - phys + - phy-names + - power-domains + - operating-points-v2 + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/qcom,dispcc-sdm845.h> + #include <dt-bindings/clock/qcom,gcc-sdm845.h> + #include <dt-bindings/power/qcom-rpmpd.h> + + dsi@ae94000 { + compatible = "qcom,mdss-dsi-ctrl"; + reg = <0x0ae94000 0x400>; + reg-names = "dsi_ctrl"; + + #address-cells = <1>; + #size-cells = <0>; + + interrupt-parent = <&mdss>; + interrupts = <4>; + + clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>, + <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>, + <&dispcc DISP_CC_MDSS_PCLK0_CLK>, + <&dispcc DISP_CC_MDSS_ESC0_CLK>, + <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&dispcc DISP_CC_MDSS_AXI_CLK>; + clock-names = "byte", + "byte_intf", + "pixel", + "core", + "iface", + "bus"; + + phys = <&dsi0_phy>; + phy-names = "dsi"; + + power-domains = <&rpmhpd SC7180_CX>; + operating-points-v2 = <&dsi_opp_table>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + dsi0_in: endpoint { + remote-endpoint = <&dpu_intf1_out>; + }; + }; + + port@1 { + reg = <1>; + dsi0_out: endpoint { + remote-endpoint = <&sn65dsi86_in>; + data-lanes = <0 1 2 3>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/display/msm/dsi.txt b/Documentation/devicetree/bindings/display/msm/dsi.txt deleted file mode 100644 index b9a64d3..0000000 --- a/Documentation/devicetree/bindings/display/msm/dsi.txt +++ /dev/null @@ -1,249 +0,0 @@ -Qualcomm Technologies Inc. adreno/snapdragon DSI output - -DSI Controller: -Required properties: -- compatible: - * "qcom,mdss-dsi-ctrl" -- reg: Physical base address and length of the registers of controller -- reg-names: The names of register regions. The following regions are required: - * "dsi_ctrl" -- interrupts: The interrupt signal from the DSI block. -- power-domains: Should be <&mmcc MDSS_GDSC>. -- clocks: Phandles to device clocks. -- clock-names: the following clocks are required: - * "mdp_core" - * "iface" - * "bus" - * "core_mmss" - * "byte" - * "pixel" - * "core" - For DSIv2, we need an additional clock: - * "src" - For DSI6G v2.0 onwards, we need also need the clock: - * "byte_intf" -- assigned-clocks: Parents of "byte" and "pixel" for the given platform. -- assigned-clock-parents: The Byte clock and Pixel clock PLL outputs provided - by a DSI PHY block. See [1] for details on clock bindings. -- vdd-supply: phandle to vdd regulator device node -- vddio-supply: phandle to vdd-io regulator device node -- vdda-supply: phandle to vdda regulator device node -- phys: phandle to DSI PHY device node -- phy-names: the name of the corresponding PHY device -- syscon-sfpb: A phandle to mmss_sfpb syscon node (only for DSIv2) -- ports: Contains 2 DSI controller ports as child nodes. Each port contains - an endpoint subnode as defined in [2] and [3]. - -Optional properties: -- panel@0: Node of panel connected to this DSI controller. - See files in [4] for each supported panel. -- qcom,dual-dsi-mode: Boolean value indicating if the DSI controller is - driving a panel which needs 2 DSI links. -- qcom,master-dsi: Boolean value indicating if the DSI controller is driving - the master link of the 2-DSI panel. -- qcom,sync-dual-dsi: Boolean value indicating if the DSI controller is - driving a 2-DSI panel whose 2 links need receive command simultaneously. -- pinctrl-names: the pin control state names; should contain "default" -- pinctrl-0: the default pinctrl state (active) -- pinctrl-n: the "sleep" pinctrl state -- ports: contains DSI controller input and output ports as children, each - containing one endpoint subnode. - - DSI Endpoint properties: - - remote-endpoint: For port@0, set to phandle of the connected panel/bridge's - input endpoint. For port@1, set to the MDP interface output. See [2] for - device graph info. - - - data-lanes: this describes how the physical DSI data lanes are mapped - to the logical lanes on the given platform. The value contained in - index n describes what physical lane is mapped to the logical lane n - (DATAn, where n lies between 0 and 3). The clock lane position is fixed - and can't be changed. Hence, they aren't a part of the DT bindings. See - [3] for more info on the data-lanes property. - - For example: - - data-lanes = <3 0 1 2>; - - The above mapping describes that the logical data lane DATA0 is mapped to - the physical data lane DATA3, logical DATA1 to physical DATA0, logic DATA2 - to phys DATA1 and logic DATA3 to phys DATA2. - - There are only a limited number of physical to logical mappings possible: - <0 1 2 3> - <1 2 3 0> - <2 3 0 1> - <3 0 1 2> - <0 3 2 1> - <1 0 3 2> - <2 1 0 3> - <3 2 1 0> - -DSI PHY: -Required properties: -- compatible: Could be the following - * "qcom,dsi-phy-28nm-hpm" - * "qcom,dsi-phy-28nm-lp" - * "qcom,dsi-phy-20nm" - * "qcom,dsi-phy-28nm-8960" - * "qcom,dsi-phy-14nm" - * "qcom,dsi-phy-14nm-660" - * "qcom,dsi-phy-10nm" - * "qcom,dsi-phy-10nm-8998" - * "qcom,dsi-phy-7nm" - * "qcom,dsi-phy-7nm-8150" -- reg: Physical base address and length of the registers of PLL, PHY. Some - revisions require the PHY regulator base address, whereas others require the - PHY lane base address. See below for each PHY revision. -- reg-names: The names of register regions. The following regions are required: - For DSI 28nm HPM/LP/8960 PHYs and 20nm PHY: - * "dsi_pll" - * "dsi_phy" - * "dsi_phy_regulator" - For DSI 14nm, 10nm and 7nm PHYs: - * "dsi_pll" - * "dsi_phy" - * "dsi_phy_lane" -- clock-cells: Must be 1. The DSI PHY block acts as a clock provider, creating - 2 clocks: A byte clock (index 0), and a pixel clock (index 1). -- power-domains: Should be <&mmcc MDSS_GDSC>. -- clocks: Phandles to device clocks. See [1] for details on clock bindings. -- clock-names: the following clocks are required: - * "iface" - * "ref" (only required for new DTS files/entries) - For 28nm HPM/LP, 28nm 8960 PHYs: -- vddio-supply: phandle to vdd-io regulator device node - For 20nm PHY: -- vddio-supply: phandle to vdd-io regulator device node -- vcca-supply: phandle to vcca regulator device node - For 14nm PHY: -- vcca-supply: phandle to vcca regulator device node - For 10nm and 7nm PHY: -- vdds-supply: phandle to vdds regulator device node - -Optional properties: -- qcom,dsi-phy-regulator-ldo-mode: Boolean value indicating if the LDO mode PHY - regulator is wanted. -- qcom,mdss-mdp-transfer-time-us: Specifies the dsi transfer time for command mode - panels in microseconds. Driver uses this number to adjust - the clock rate according to the expected transfer time. - Increasing this value would slow down the mdp processing - and can result in slower performance. - Decreasing this value can speed up the mdp processing, - but this can also impact power consumption. - As a rule this time should not be higher than the time - that would be expected with the processing at the - dsi link rate since anyways this would be the maximum - transfer time that could be achieved. - If ping pong split is enabled, this time should not be higher - than two times the dsi link rate time. - If the property is not specified, then the default value is 14000 us. - -[1] Documentation/devicetree/bindings/clock/clock-bindings.txt -[2] Documentation/devicetree/bindings/graph.txt -[3] Documentation/devicetree/bindings/media/video-interfaces.txt -[4] Documentation/devicetree/bindings/display/panel/ - -Example: - dsi0: dsi@fd922800 { - compatible = "qcom,mdss-dsi-ctrl"; - qcom,dsi-host-index = <0>; - interrupt-parent = <&mdp>; - interrupts = <4 0>; - reg-names = "dsi_ctrl"; - reg = <0xfd922800 0x200>; - power-domains = <&mmcc MDSS_GDSC>; - clock-names = - "bus", - "byte", - "core", - "core_mmss", - "iface", - "mdp_core", - "pixel"; - clocks = - <&mmcc MDSS_AXI_CLK>, - <&mmcc MDSS_BYTE0_CLK>, - <&mmcc MDSS_ESC0_CLK>, - <&mmcc MMSS_MISC_AHB_CLK>, - <&mmcc MDSS_AHB_CLK>, - <&mmcc MDSS_MDP_CLK>, - <&mmcc MDSS_PCLK0_CLK>; - - assigned-clocks = - <&mmcc BYTE0_CLK_SRC>, - <&mmcc PCLK0_CLK_SRC>; - assigned-clock-parents = - <&dsi_phy0 0>, - <&dsi_phy0 1>; - - vdda-supply = <&pma8084_l2>; - vdd-supply = <&pma8084_l22>; - vddio-supply = <&pma8084_l12>; - - phys = <&dsi_phy0>; - phy-names ="dsi-phy"; - - qcom,dual-dsi-mode; - qcom,master-dsi; - qcom,sync-dual-dsi; - - qcom,mdss-mdp-transfer-time-us = <12000>; - - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&dsi_active>; - pinctrl-1 = <&dsi_suspend>; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - dsi0_in: endpoint { - remote-endpoint = <&mdp_intf1_out>; - }; - }; - - port@1 { - reg = <1>; - dsi0_out: endpoint { - remote-endpoint = <&panel_in>; - data-lanes = <0 1 2 3>; - }; - }; - }; - - panel: panel@0 { - compatible = "sharp,lq101r1sx01"; - reg = <0>; - link2 = <&secondary>; - - power-supply = <...>; - backlight = <...>; - - port { - panel_in: endpoint { - remote-endpoint = <&dsi0_out>; - }; - }; - }; - }; - - dsi_phy0: dsi-phy@fd922a00 { - compatible = "qcom,dsi-phy-28nm-hpm"; - qcom,dsi-phy-index = <0>; - reg-names = - "dsi_pll", - "dsi_phy", - "dsi_phy_regulator"; - reg = <0xfd922a00 0xd4>, - <0xfd922b00 0x2b0>, - <0xfd922d80 0x7b>; - clock-names = "iface"; - clocks = <&mmcc MDSS_AHB_CLK>; - #clock-cells = <1>; - vddio-supply = <&pma8084_l12>; - - qcom,dsi-phy-regulator-ldo-mode; - };
On Mon, 24 May 2021 17:14:11 +0530, Krishna Manikandan wrote:
Reviewed-by: Rob Herring robh@kernel.org
Add YAML schema for the device tree bindings for DSI PHY.
Signed-off-by: Krishna Manikandan mkrishn@codeaurora.org Reviewed-by: Bjorn Andersson bjorn.andersson@linaro.org Reviewed-by: Stephen Boyd swboyd@chromium.org Reviewed-by: Rob Herring robh@kernel.org --- Changes in v1: - Merge dsi-phy.yaml and dsi-phy-10nm.yaml (Stephen Boyd) - Remove qcom,dsi-phy-regulator-ldo-mode (Stephen Boyd) - Add clock cells properly (Stephen Boyd) - Remove unnecessary decription from clock names (Stephen Boyd) - Add pin names for the supply entries for 10nm phy which is used in sc7180 and sdm845 (Stephen Boyd) - Remove unused header files from examples (Stephen Boyd) - Drop labels for display nodes and correct node name (Stephen Boyd)
Changes in v2: - Drop maxItems for clock (Stephen Boyd) - Add vdds supply pin information for sdm845 (Stephen Boyd) - Add examples for 14nm, 20nm and 28nm phy yaml files (Stephen Boyd) - Keep child nodes directly under soc node (Stephen Boyd)
Changes in v3: - Use a separate yaml file to describe the common properties for all the dsi phy versions (Stephen Boyd) - Remove soc from examples (Stephen Boyd) - Add description for register property
Changes in v4: - Modify the title for all the phy versions (Stephen Boyd) - Drop description for all the phy versions (Stephen Boyd) - Modify the description for register property (Stephen Boyd)
Changes in v5: - Remove unused properties from common dsi phy file - Add clock-cells and phy-cells to required property list (Stephen Boyd)
Changes in v6: - Add proper compatible string in example
.../bindings/display/msm/dsi-phy-10nm.yaml | 68 +++++++++++++++++++++ .../bindings/display/msm/dsi-phy-14nm.yaml | 66 ++++++++++++++++++++ .../bindings/display/msm/dsi-phy-20nm.yaml | 71 ++++++++++++++++++++++ .../bindings/display/msm/dsi-phy-28nm.yaml | 68 +++++++++++++++++++++ .../bindings/display/msm/dsi-phy-common.yaml | 40 ++++++++++++ 5 files changed, 313 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-phy-10nm.yaml create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-phy-14nm.yaml create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-phy-20nm.yaml create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-phy-28nm.yaml create mode 100644 Documentation/devicetree/bindings/display/msm/dsi-phy-common.yaml
diff --git a/Documentation/devicetree/bindings/display/msm/dsi-phy-10nm.yaml b/Documentation/devicetree/bindings/display/msm/dsi-phy-10nm.yaml new file mode 100644 index 0000000..4a26bef --- /dev/null +++ b/Documentation/devicetree/bindings/display/msm/dsi-phy-10nm.yaml @@ -0,0 +1,68 @@ +# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/msm/dsi-phy-10nm.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Display DSI 10nm PHY + +maintainers: + - Krishna Manikandan mkrishn@codeaurora.org + +allOf: + - $ref: dsi-phy-common.yaml# + +properties: + compatible: + oneOf: + - const: qcom,dsi-phy-10nm + - const: qcom,dsi-phy-10nm-8998 + + reg: + items: + - description: dsi phy register set + - description: dsi phy lane register set + - description: dsi pll register set + + reg-names: + items: + - const: dsi_phy + - const: dsi_phy_lane + - const: dsi_pll + + vdds-supply: + description: | + Connected to DSI0_MIPI_DSI_PLL_VDDA0P9 pin for sc7180 target and + connected to VDDA_MIPI_DSI_0_PLL_0P9 pin for sdm845 target + +required: + - compatible + - reg + - reg-names + - vdds-supply + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,dispcc-sdm845.h> + #include <dt-bindings/clock/qcom,rpmh.h> + + dsi-phy@ae94400 { + compatible = "qcom,dsi-phy-10nm"; + reg = <0x0ae94400 0x200>, + <0x0ae94600 0x280>, + <0x0ae94a00 0x1e0>; + reg-names = "dsi_phy", + "dsi_phy_lane", + "dsi_pll"; + + #clock-cells = <1>; + #phy-cells = <0>; + + vdds-supply = <&vdda_mipi_dsi0_pll>; + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&rpmhcc RPMH_CXO_CLK>; + clock-names = "iface", "ref"; + }; +... diff --git a/Documentation/devicetree/bindings/display/msm/dsi-phy-14nm.yaml b/Documentation/devicetree/bindings/display/msm/dsi-phy-14nm.yaml new file mode 100644 index 0000000..72a00cc --- /dev/null +++ b/Documentation/devicetree/bindings/display/msm/dsi-phy-14nm.yaml @@ -0,0 +1,66 @@ +# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/msm/dsi-phy-14nm.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Display DSI 14nm PHY + +maintainers: + - Krishna Manikandan mkrishn@codeaurora.org + +allOf: + - $ref: dsi-phy-common.yaml# + +properties: + compatible: + oneOf: + - const: qcom,dsi-phy-14nm + - const: qcom,dsi-phy-14nm-660 + + reg: + items: + - description: dsi phy register set + - description: dsi phy lane register set + - description: dsi pll register set + + reg-names: + items: + - const: dsi_phy + - const: dsi_phy_lane + - const: dsi_pll + + vcca-supply: + description: Phandle to vcca regulator device node. + +required: + - compatible + - reg + - reg-names + - vcca-supply + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,dispcc-sdm845.h> + #include <dt-bindings/clock/qcom,rpmh.h> + + dsi-phy@ae94400 { + compatible = "qcom,dsi-phy-14nm"; + reg = <0x0ae94400 0x200>, + <0x0ae94600 0x280>, + <0x0ae94a00 0x1e0>; + reg-names = "dsi_phy", + "dsi_phy_lane", + "dsi_pll"; + + #clock-cells = <1>; + #phy-cells = <0>; + + vcca-supply = <&vcca_reg>; + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&rpmhcc RPMH_CXO_CLK>; + clock-names = "iface", "ref"; + }; +... diff --git a/Documentation/devicetree/bindings/display/msm/dsi-phy-20nm.yaml b/Documentation/devicetree/bindings/display/msm/dsi-phy-20nm.yaml new file mode 100644 index 0000000..743806d --- /dev/null +++ b/Documentation/devicetree/bindings/display/msm/dsi-phy-20nm.yaml @@ -0,0 +1,71 @@ +# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/msm/dsi-phy-20nm.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Display DSI 20nm PHY + +maintainers: + - Krishna Manikandan mkrishn@codeaurora.org + +allOf: + - $ref: dsi-phy-common.yaml# + +properties: + compatible: + oneOf: + - const: qcom,dsi-phy-20nm + + reg: + items: + - description: dsi pll register set + - description: dsi phy register set + - description: dsi phy regulator register set + + reg-names: + items: + - const: dsi_pll + - const: dsi_phy + - const: dsi_phy_regulator + + vcca-supply: + description: Phandle to vcca regulator device node. + + vddio-supply: + description: Phandle to vdd-io regulator device node. + +required: + - compatible + - reg + - reg-names + - vddio-supply + - vcca-supply + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,dispcc-sdm845.h> + #include <dt-bindings/clock/qcom,rpmh.h> + + dsi-phy@fd922a00 { + compatible = "qcom,dsi-phy-20nm"; + reg = <0xfd922a00 0xd4>, + <0xfd922b00 0x2b0>, + <0xfd922d80 0x7b>; + reg-names = "dsi_pll", + "dsi_phy", + "dsi_phy_regulator"; + + #clock-cells = <1>; + #phy-cells = <0>; + + vcca-supply = <&vcca_reg>; + vddio-supply = <&vddio_reg>; + + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&rpmhcc RPMH_CXO_CLK>; + clock-names = "iface", "ref"; + }; +... diff --git a/Documentation/devicetree/bindings/display/msm/dsi-phy-28nm.yaml b/Documentation/devicetree/bindings/display/msm/dsi-phy-28nm.yaml new file mode 100644 index 0000000..b106007 --- /dev/null +++ b/Documentation/devicetree/bindings/display/msm/dsi-phy-28nm.yaml @@ -0,0 +1,68 @@ +# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/msm/dsi-phy-28nm.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Display DSI 28nm PHY + +maintainers: + - Krishna Manikandan mkrishn@codeaurora.org + +allOf: + - $ref: dsi-phy-common.yaml# + +properties: + compatible: + oneOf: + - const: qcom,dsi-phy-28nm-hpm + - const: qcom,dsi-phy-28nm-lp + - const: qcom,dsi-phy-28nm-8960 + + reg: + items: + - description: dsi pll register set + - description: dsi phy register set + - description: dsi phy regulator register set + + reg-names: + items: + - const: dsi_pll + - const: dsi_phy + - const: dsi_phy_regulator + + vddio-supply: + description: Phandle to vdd-io regulator device node. + +required: + - compatible + - reg + - reg-names + - vddio-supply + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,dispcc-sdm845.h> + #include <dt-bindings/clock/qcom,rpmh.h> + + dsi-phy@fd922a00 { + compatible = "qcom,dsi-phy-28nm-lp"; + reg = <0xfd922a00 0xd4>, + <0xfd922b00 0x2b0>, + <0xfd922d80 0x7b>; + reg-names = "dsi_pll", + "dsi_phy", + "dsi_phy_regulator"; + + #clock-cells = <1>; + #phy-cells = <0>; + + vddio-supply = <&vddio_reg>; + + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&rpmhcc RPMH_CXO_CLK>; + clock-names = "iface", "ref"; + }; +... diff --git a/Documentation/devicetree/bindings/display/msm/dsi-phy-common.yaml b/Documentation/devicetree/bindings/display/msm/dsi-phy-common.yaml new file mode 100644 index 0000000..502bdda --- /dev/null +++ b/Documentation/devicetree/bindings/display/msm/dsi-phy-common.yaml @@ -0,0 +1,40 @@ +# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/msm/dsi-phy-common.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Description of Qualcomm Display DSI PHY common dt properties + +maintainers: + - Krishna Manikandan mkrishn@codeaurora.org + +description: | + This defines the DSI PHY dt properties which are common for all + dsi phy versions. + +properties: + "#clock-cells": + const: 1 + + "#phy-cells": + const: 0 + + clocks: + items: + - description: Display AHB clock + - description: Board XO source + + clock-names: + items: + - const: iface + - const: ref + +required: + - clocks + - clock-names + - "#clock-cells" + - "#phy-cells" + +additionalProperties: true +...
Add bindings for Snapdragon DisplayPort controller driver.
Signed-off-by: Chandan Uddaraju chandanu@codeaurora.org Signed-off-by: Vara Reddy varar@codeaurora.org Signed-off-by: Tanmay Shah tanmay@codeaurora.org Signed-off-by: Kuogee Hsieh khsieh@codeaurora.org Signed-off-by: Krishna Manikandan mkrishn@codeaurora.org Reviewed-by: Bjorn Andersson bjorn.andersson@linaro.org Reviewed-by: Rob Herring robh@kernel.org Reviewed-by: Stephen Boyd swboyd@chromium.org --- Changes in V2: -Provide details about sel-gpio
Changes in V4: -Provide details about max dp lanes -Change the commit text
Changes in V5: -moved dp.txt to yaml file
Changes in v6: - Squash all AUX LUT properties into one pattern Property - Make aux-cfg[0-9]-settings properties optional - Remove PLL/PHY bindings from DP controller dts - Add DP clocks description - Remove _clk suffix from clock names - Rename pixel clock to stream_pixel - Remove redundant bindings (GPIO, PHY, HDCP clock, etc..) - Fix indentation - Add Display Port as interface of DPU in DPU bindings and add port mapping accordingly.
Chages in v7: - Add dp-controller.yaml file common between multiple SOC - Rename dp-sc7180.yaml to dp-controller-sc7180.yaml - change compatible string and add SOC name to it. - Remove Root clock generator for pixel clock - Add assigned-clocks and assigned-clock-parents bindings - Remove redundant properties, descriptions and blank lines - Add DP port in DPU bindings - Update depends-on tag in commit message and rebase change accordingly
Changes in v8: - Add MDSS AHB clock in bindings
Changes in v9: - Remove redundant reg-name property - Change assigned-clocks and assigned-clocks-parents counts to 2 - Use IRQ flags in example dts
Changes in v10: - Change title of this patch as it does not contain PLL bindings anymore - Remove redundant properties - Remove use of IRQ flag - Fix ports property
Changes in v11: - add ports required of both #address-cells and #size-cells - add required operating-points-v2 - add required #sound-dai-cells - add required power-domains - update maintainer list
Changes in v12: - remove soc node from examples (Stephen Boyd) - split dpu-sc7180.yaml changes to separate patch (Stephen Boyd)
Changes in v13: - add assigned-clocks - add assigned-clock-parents
Changes in v14: - add reference for ports (Rob Herring)
Changes in v15: - drop common properties from ports (Rob Herring)
.../bindings/display/msm/dp-controller.yaml | 146 +++++++++++++++++++++ 1 file changed, 146 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/msm/dp-controller.yaml
diff --git a/Documentation/devicetree/bindings/display/msm/dp-controller.yaml b/Documentation/devicetree/bindings/display/msm/dp-controller.yaml new file mode 100644 index 0000000..64d8d9e --- /dev/null +++ b/Documentation/devicetree/bindings/display/msm/dp-controller.yaml @@ -0,0 +1,146 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/msm/dp-controller.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MSM Display Port Controller + +maintainers: + - Kuogee Hsieh khsieh@codeaurora.org + +description: | + Device tree bindings for DisplayPort host controller for MSM targets + that are compatible with VESA DisplayPort interface specification. + +properties: + compatible: + enum: + - qcom,sc7180-dp + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: AHB clock to enable register access + - description: Display Port AUX clock + - description: Display Port Link clock + - description: Link interface clock between DP and PHY + - description: Display Port Pixel clock + + clock-names: + items: + - const: core_iface + - const: core_aux + - const: ctrl_link + - const: ctrl_link_iface + - const: stream_pixel + + assigned-clocks: + items: + - description: link clock source + - description: pixel clock source + + assigned-clock-parents: + items: + - description: phy 0 parent + - description: phy 1 parent + + phys: + maxItems: 1 + + phy-names: + items: + - const: dp + + operating-points-v2: + maxItems: 1 + + power-domains: + maxItems: 1 + + "#sound-dai-cells": + const: 0 + + ports: + $ref: /schemas/graph.yaml#/properties/ports + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: Input endpoint of the controller + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: Output endpoint of the controller + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - phys + - phy-names + - "#sound-dai-cells" + - power-domains + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/qcom,dispcc-sc7180.h> + #include <dt-bindings/power/qcom-aoss-qmp.h> + #include <dt-bindings/power/qcom-rpmpd.h> + + displayport-controller@ae90000 { + compatible = "qcom,sc7180-dp"; + reg = <0xae90000 0x1400>; + interrupt-parent = <&mdss>; + interrupts = <12>; + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&dispcc DISP_CC_MDSS_DP_AUX_CLK>, + <&dispcc DISP_CC_MDSS_DP_LINK_CLK>, + <&dispcc DISP_CC_MDSS_DP_LINK_INTF_CLK>, + <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK>; + clock-names = "core_iface", "core_aux", + "ctrl_link", + "ctrl_link_iface", "stream_pixel"; + + assigned-clocks = <&dispcc DISP_CC_MDSS_DP_LINK_CLK_SRC>, + <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK_SRC>; + + assigned-clock-parents = <&dp_phy 0>, <&dp_phy 1>; + + phys = <&dp_phy>; + phy-names = "dp"; + + #sound-dai-cells = <0>; + + power-domains = <&rpmhpd SC7180_CX>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + endpoint { + remote-endpoint = <&dpu_intf0_out>; + }; + }; + + port@1 { + reg = <1>; + endpoint { + remote-endpoint = <&typec>; + }; + }; + }; + }; +...
dri-devel@lists.freedesktop.org
-
Krishna Manikandan -
Rob Herring